summaryrefslogtreecommitdiffstats
path: root/Documentation/devicetree/bindings/net/marvell-bt-8xxx.txt
diff options
context:
space:
mode:
Diffstat (limited to '')
-rw-r--r--Documentation/devicetree/bindings/net/marvell-bt-8xxx.txt83
1 files changed, 83 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/net/marvell-bt-8xxx.txt b/Documentation/devicetree/bindings/net/marvell-bt-8xxx.txt
new file mode 100644
index 000000000..957e5e5c2
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/marvell-bt-8xxx.txt
@@ -0,0 +1,83 @@
+Marvell 8897/8997 (sd8897/sd8997) bluetooth devices (SDIO or USB based)
+------
+The 8997 devices supports multiple interfaces. When used on SDIO interfaces,
+the btmrvl driver is used and when used on USB interface, the btusb driver is
+used.
+
+Required properties:
+
+ - compatible : should be one of the following:
+ * "marvell,sd8897-bt" (for SDIO)
+ * "marvell,sd8997-bt" (for SDIO)
+ * "usb1286,204e" (for USB)
+
+Optional properties:
+
+ - marvell,cal-data: Calibration data downloaded to the device during
+ initialization. This is an array of 28 values(u8).
+ This is only applicable to SDIO devices.
+
+ - marvell,wakeup-pin: It represents wakeup pin number of the bluetooth chip.
+ firmware will use the pin to wakeup host system (u16).
+ - marvell,wakeup-gap-ms: wakeup gap represents wakeup latency of the host
+ platform. The value will be configured to firmware. This
+ is needed to work chip's sleep feature as expected (u16).
+ - interrupt-names: Used only for USB based devices (See below)
+ - interrupts : specifies the interrupt pin number to the cpu. For SDIO, the
+ driver will use the first interrupt specified in the interrupt
+ array. For USB based devices, the driver will use the interrupt
+ named "wakeup" from the interrupt-names and interrupt arrays.
+ The driver will request an irq based on this interrupt number.
+ During system suspend, the irq will be enabled so that the
+ bluetooth chip can wakeup host platform under certain
+ conditions. During system resume, the irq will be disabled
+ to make sure unnecessary interrupt is not received.
+
+Example:
+
+IRQ pin 119 is used as system wakeup source interrupt.
+wakeup pin 13 and gap 100ms are configured so that firmware can wakeup host
+using this device side pin and wakeup latency.
+
+Example for SDIO device follows (calibration data is also available in
+below example).
+
+&mmc3 {
+ vmmc-supply = <&wlan_en_reg>;
+ bus-width = <4>;
+ cap-power-off-card;
+ keep-power-in-suspend;
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+ btmrvl: bluetooth@2 {
+ compatible = "marvell,sd8897-bt";
+ reg = <2>;
+ interrupt-parent = <&pio>;
+ interrupts = <119 IRQ_TYPE_LEVEL_LOW>;
+
+ marvell,cal-data = /bits/ 8 <
+ 0x37 0x01 0x1c 0x00 0xff 0xff 0xff 0xff 0x01 0x7f 0x04 0x02
+ 0x00 0x00 0xba 0xce 0xc0 0xc6 0x2d 0x00 0x00 0x00 0x00 0x00
+ 0x00 0x00 0xf0 0x00>;
+ marvell,wakeup-pin = /bits/ 16 <0x0d>;
+ marvell,wakeup-gap-ms = /bits/ 16 <0x64>;
+ };
+};
+
+Example for USB device:
+
+&usb_host1_ohci {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mvl_bt1: bt@1 {
+ compatible = "usb1286,204e";
+ reg = <1>;
+ interrupt-parent = <&gpio0>;
+ interrupt-names = "wakeup";
+ interrupts = <119 IRQ_TYPE_LEVEL_LOW>;
+ marvell,wakeup-pin = /bits/ 16 <0x0d>;
+ marvell,wakeup-gap-ms = /bits/ 16 <0x64>;
+ };
+};