summaryrefslogtreecommitdiffstats
path: root/Documentation/devicetree/bindings/net/mediatek-bluetooth.txt
diff options
context:
space:
mode:
Diffstat (limited to '')
-rw-r--r--Documentation/devicetree/bindings/net/mediatek-bluetooth.txt116
1 files changed, 116 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/net/mediatek-bluetooth.txt b/Documentation/devicetree/bindings/net/mediatek-bluetooth.txt
new file mode 100644
index 000000000..9ef5bacda
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/mediatek-bluetooth.txt
@@ -0,0 +1,116 @@
+MediaTek SoC built-in Bluetooth Devices
+==================================
+
+This device is a serial attached device to BTIF device and thus it must be a
+child node of the serial node with BTIF. The dt-bindings details for BTIF
+device can be known via Documentation/devicetree/bindings/serial/8250.yaml.
+
+Required properties:
+
+- compatible: Must be
+ "mediatek,mt7622-bluetooth": for MT7622 SoC
+- clocks: Should be the clock specifiers corresponding to the entry in
+ clock-names property.
+- clock-names: Should contain "ref" entries.
+- power-domains: Phandle to the power domain that the device is part of
+
+Example:
+
+ btif: serial@1100c000 {
+ compatible = "mediatek,mt7622-btif",
+ "mediatek,mtk-btif";
+ reg = <0 0x1100c000 0 0x1000>;
+ interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&pericfg CLK_PERI_BTIF_PD>;
+ clock-names = "main";
+ reg-shift = <2>;
+ reg-io-width = <4>;
+
+ bluetooth {
+ compatible = "mediatek,mt7622-bluetooth";
+ power-domains = <&scpsys MT7622_POWER_DOMAIN_WB>;
+ clocks = <&clk25m>;
+ clock-names = "ref";
+ };
+ };
+
+MediaTek UART based Bluetooth Devices
+==================================
+
+This device is a serial attached device to UART device and thus it must be a
+child node of the serial node with UART.
+
+Please refer to the following documents for generic properties:
+
+ Documentation/devicetree/bindings/serial/serial.yaml
+
+Required properties:
+
+- compatible: Must be
+ "mediatek,mt7663u-bluetooth": for MT7663U device
+ "mediatek,mt7668u-bluetooth": for MT7668U device
+- vcc-supply: Main voltage regulator
+
+If the pin controller on the platform can support both pinmux and GPIO
+control such as the most of MediaTek platform. Please use below properties.
+
+- pinctrl-names: Should be "default", "runtime"
+- pinctrl-0: Should contain UART RXD low when the device is powered up to
+ enter proper bootstrap mode.
+- pinctrl-1: Should contain UART mode pin ctrl
+
+Else, the pin controller on the platform only can support pinmux control and
+the GPIO control still has to rely on the dedicated GPIO controller such as
+a legacy MediaTek SoC, MT7621. Please use the below properties.
+
+- boot-gpios: GPIO same to the pin as UART RXD and used to keep LOW when
+ the device is powered up to enter proper bootstrap mode when
+- pinctrl-names: Should be "default"
+- pinctrl-0: Should contain UART mode pin ctrl
+
+Optional properties:
+
+- reset-gpios: GPIO used to reset the device whose initial state keeps low,
+ if the GPIO is missing, then board-level design should be
+ guaranteed.
+- clocks: Should be the clock specifiers corresponding to the entry in
+ clock-names property. If the clock is missing, then board-level
+ design should be guaranteed.
+- clock-names: Should contain "osc" entry for the external oscillator.
+- current-speed: Current baud rate of the device whose defaults to 921600
+
+Example:
+
+ uart1_pins_boot: uart1-default {
+ pins-dat {
+ pinmux = <MT7623_PIN_81_URXD1_FUNC_GPIO81>;
+ output-low;
+ };
+ };
+
+ uart1_pins_runtime: uart1-runtime {
+ pins-dat {
+ pinmux = <MT7623_PIN_81_URXD1_FUNC_URXD1>,
+ <MT7623_PIN_82_UTXD1_FUNC_UTXD1>;
+ };
+ };
+
+ uart1: serial@11003000 {
+ compatible = "mediatek,mt7623-uart",
+ "mediatek,mt6577-uart";
+ reg = <0 0x11003000 0 0x400>;
+ interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&pericfg CLK_PERI_UART1_SEL>,
+ <&pericfg CLK_PERI_UART1>;
+ clock-names = "baud", "bus";
+
+ bluetooth {
+ compatible = "mediatek,mt7663u-bluetooth";
+ vcc-supply = <&reg_5v>;
+ reset-gpios = <&pio 24 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default", "runtime";
+ pinctrl-0 = <&uart1_pins_boot>;
+ pinctrl-1 = <&uart1_pins_runtime>;
+ current-speed = <921600>;
+ };
+ };