summaryrefslogtreecommitdiffstats
path: root/Documentation/devicetree/bindings/pinctrl/brcm,iproc-gpio.txt
diff options
context:
space:
mode:
Diffstat (limited to '')
-rw-r--r--Documentation/devicetree/bindings/pinctrl/brcm,iproc-gpio.txt123
1 files changed, 123 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,iproc-gpio.txt b/Documentation/devicetree/bindings/pinctrl/brcm,iproc-gpio.txt
new file mode 100644
index 000000000..a73cbeb0f
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/brcm,iproc-gpio.txt
@@ -0,0 +1,123 @@
+Broadcom iProc GPIO/PINCONF Controller
+
+Required properties:
+
+- compatible:
+ "brcm,iproc-gpio" for the generic iProc based GPIO controller IP that
+ supports full-featured pinctrl and GPIO functions used in various iProc
+ based SoCs
+
+ May contain an SoC-specific compatibility string to accommodate any
+ SoC-specific features
+
+ "brcm,cygnus-ccm-gpio", "brcm,cygnus-asiu-gpio", or
+ "brcm,cygnus-crmu-gpio" for Cygnus SoCs
+
+ "brcm,iproc-nsp-gpio" for the iProc NSP SoC that has drive strength support
+ disabled
+
+ "brcm,iproc-stingray-gpio" for the iProc Stingray SoC that has the general
+ pinctrl support completely disabled in this IP block. In Stingray, a
+ different IP block is used to handle pinctrl related functions
+
+- reg:
+ Define the base and range of the I/O address space that contains SoC
+GPIO/PINCONF controller registers
+
+- ngpios:
+ Total number of in-use slots in GPIO controller
+
+- #gpio-cells:
+ Must be two. The first cell is the GPIO pin number (within the
+controller's pin space) and the second cell is used for the following:
+ bit[0]: polarity (0 for active high and 1 for active low)
+
+- gpio-controller:
+ Specifies that the node is a GPIO controller
+
+Optional properties:
+
+- interrupts:
+ Interrupt ID
+
+- interrupt-controller:
+ Specifies that the node is an interrupt controller
+
+- gpio-ranges:
+ Specifies the mapping between gpio controller and pin-controllers pins.
+ This requires 4 fields in cells defined as -
+ 1. Phandle of pin-controller.
+ 2. GPIO base pin offset.
+ 3 Pin-control base pin offset.
+ 4. number of gpio pins which are linearly mapped from pin base.
+
+Supported generic PINCONF properties in child nodes:
+
+- pins:
+ The list of pins (within the controller's own pin space) that properties
+in the node apply to. Pin names are "gpio-<pin>"
+
+- bias-disable:
+ Disable pin bias
+
+- bias-pull-up:
+ Enable internal pull up resistor
+
+- bias-pull-down:
+ Enable internal pull down resistor
+
+- drive-strength:
+ Valid drive strength values include 2, 4, 6, 8, 10, 12, 14, 16 (mA)
+
+Example:
+ gpio_ccm: gpio@1800a000 {
+ compatible = "brcm,cygnus-ccm-gpio";
+ reg = <0x1800a000 0x50>,
+ <0x0301d164 0x20>;
+ ngpios = <24>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+
+ touch_pins: touch_pins {
+ pwr: pwr {
+ pins = "gpio-0";
+ drive-strength = <16>;
+ };
+
+ event: event {
+ pins = "gpio-1";
+ bias-pull-up;
+ };
+ };
+ };
+
+ gpio_asiu: gpio@180a5000 {
+ compatible = "brcm,cygnus-asiu-gpio";
+ reg = <0x180a5000 0x668>;
+ ngpios = <146>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-controller;
+ gpio-ranges = <&pinctrl 0 42 1>,
+ <&pinctrl 1 44 3>;
+ };
+
+ /*
+ * Touchscreen that uses the CCM GPIO 0 and 1
+ */
+ tsc {
+ ...
+ ...
+ gpio-pwr = <&gpio_ccm 0 0>;
+ gpio-event = <&gpio_ccm 1 0>;
+ };
+
+ /* Bluetooth that uses the ASIU GPIO 5, with polarity inverted */
+ bluetooth {
+ ...
+ ...
+ bcm,rfkill-bank-sel = <&gpio_asiu 5 1>
+ }