summaryrefslogtreecommitdiffstats
path: root/Documentation/devicetree/bindings/pinctrl/pinctrl-mcp23s08.txt
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/devicetree/bindings/pinctrl/pinctrl-mcp23s08.txt')
-rw-r--r--Documentation/devicetree/bindings/pinctrl/pinctrl-mcp23s08.txt146
1 files changed, 146 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-mcp23s08.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-mcp23s08.txt
new file mode 100644
index 000000000..8b94aa8f5
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-mcp23s08.txt
@@ -0,0 +1,146 @@
+Microchip MCP2308/MCP23S08/MCP23017/MCP23S17 driver for
+8-/16-bit I/O expander with serial interface (I2C/SPI)
+
+Required properties:
+- compatible : Should be
+ - "mcp,mcp23s08" (DEPRECATED) for 8 GPIO SPI version
+ - "mcp,mcp23s17" (DEPRECATED) for 16 GPIO SPI version
+ - "mcp,mcp23008" (DEPRECATED) for 8 GPIO I2C version or
+ - "mcp,mcp23017" (DEPRECATED) for 16 GPIO I2C version of the chip
+
+ - "microchip,mcp23s08" for 8 GPIO SPI version
+ - "microchip,mcp23s17" for 16 GPIO SPI version
+ - "microchip,mcp23s18" for 16 GPIO SPI version
+ - "microchip,mcp23008" for 8 GPIO I2C version or
+ - "microchip,mcp23017" for 16 GPIO I2C version of the chip
+ - "microchip,mcp23018" for 16 GPIO I2C version
+ NOTE: Do not use the old mcp prefix any more. It is deprecated and will be
+ removed.
+- #gpio-cells : Should be two.
+ - first cell is the pin number
+ - second cell is used to specify flags as described in
+ 'Documentation/devicetree/bindings/gpio/gpio.txt'. Allowed values defined by
+ 'include/dt-bindings/gpio/gpio.h' (e.g. GPIO_ACTIVE_LOW).
+- gpio-controller : Marks the device node as a GPIO controller.
+- reg : For an address on its bus. I2C uses this a the I2C address of the chip.
+ SPI uses this to specify the chipselect line which the chip is
+ connected to. The driver and the SPI variant of the chip support
+ multiple chips on the same chipselect. Have a look at
+ microchip,spi-present-mask below.
+
+Required device specific properties (only for SPI chips):
+- mcp,spi-present-mask (DEPRECATED)
+- microchip,spi-present-mask : This is a present flag, that makes only sense for SPI
+ chips - as the name suggests. Multiple SPI chips can share the same
+ SPI chipselect. Set a bit in bit0-7 in this mask to 1 if there is a
+ chip connected with the corresponding spi address set. For example if
+ you have a chip with address 3 connected, you have to set bit3 to 1,
+ which is 0x08. mcp23s08 chip variant only supports bits 0-3. It is not
+ possible to mix mcp23s08 and mcp23s17 on the same chipselect. Set at
+ least one bit to 1 for SPI chips.
+ NOTE: Do not use the old mcp prefix any more. It is deprecated and will be
+ removed.
+- spi-max-frequency = The maximum frequency this chip is able to handle
+
+Optional properties:
+- #interrupt-cells : Should be two.
+ - first cell is the pin number
+ - second cell is used to specify flags.
+- interrupt-controller: Marks the device node as a interrupt controller.
+- drive-open-drain: Sets the ODR flag in the IOCON register. This configures
+ the IRQ output as open drain active low.
+
+Optional device specific properties:
+- microchip,irq-mirror: Sets the mirror flag in the IOCON register. Devices
+ with two interrupt outputs (these are the devices ending with 17 and
+ those that have 16 IOs) have two IO banks: IO 0-7 form bank 1 and
+ IO 8-15 are bank 2. These chips have two different interrupt outputs:
+ One for bank 1 and another for bank 2. If irq-mirror is set, both
+ interrupts are generated regardless of the bank that an input change
+ occurred on. If it is not set, the interrupt are only generated for the
+ bank they belong to.
+ On devices with only one interrupt output this property is useless.
+- microchip,irq-active-high: Sets the INTPOL flag in the IOCON register. This
+ configures the IRQ output polarity as active high.
+
+Example I2C (with interrupt):
+gpiom1: gpio@20 {
+ compatible = "microchip,mcp23017";
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x20>;
+
+ interrupt-parent = <&gpio1>;
+ interrupts = <17 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #interrupt-cells=<2>;
+ microchip,irq-mirror;
+};
+
+Example SPI:
+gpiom1: gpio@0 {
+ compatible = "microchip,mcp23s17";
+ gpio-controller;
+ #gpio-cells = <2>;
+ microchip,spi-present-mask = <0x01>;
+ reg = <0>;
+ spi-max-frequency = <1000000>;
+};
+
+Pull-up configuration
+=====================
+
+If pins are used as output, they can also be configured with pull-ups. This is
+done with pinctrl.
+
+Please refer file <devicetree/bindings/pinctrl/pinctrl-bindings.txt>
+for details of the common pinctrl bindings used by client devices,
+including the meaning of the phrase "pin configuration node".
+
+Optional Pinmux properties:
+--------------------------
+Following properties are required if default setting of pins are required
+at boot.
+- pinctrl-names: A pinctrl state named per <pinctrl-bindings.txt>.
+- pinctrl[0...n]: Properties to contain the phandle for pinctrl states per
+ <pinctrl-bindings.txt>.
+
+The pin configurations are defined as child of the pinctrl states node. Each
+sub-node have following properties:
+
+Required properties:
+------------------
+- pins: List of pins. Valid values of pins properties are:
+ gpio0 ... gpio7 for the devices with 8 GPIO pins and
+ gpio0 ... gpio15 for the devices with 16 GPIO pins.
+
+Optional properties:
+-------------------
+The following optional property is defined in the pinmux DT binding document
+<pinctrl-bindings.txt>. Absence of this property will leave the configuration
+in its default state.
+ bias-pull-up
+
+Example with pinctrl to pull-up output pins:
+gpio21: gpio@21 {
+ compatible = "microchip,mcp23017";
+ gpio-controller;
+ #gpio-cells = <0x2>;
+ reg = <0x21>;
+ interrupt-parent = <&socgpio>;
+ interrupts = <0x17 0x8>;
+ interrupt-names = "mcp23017@21 irq";
+ interrupt-controller;
+ #interrupt-cells = <0x2>;
+ microchip,irq-mirror;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2cgpio0irq &gpio21pullups>;
+
+ gpio21pullups: pinmux {
+ pins = "gpio0", "gpio1", "gpio2", "gpio3",
+ "gpio4", "gpio5", "gpio6", "gpio7",
+ "gpio8", "gpio9", "gpio10", "gpio11",
+ "gpio12", "gpio13", "gpio14", "gpio15";
+ bias-pull-up;
+ };
+};