diff options
Diffstat (limited to '')
| -rw-r--r-- | Documentation/devicetree/bindings/regulator/rohm,bd71847-regulator.yaml | 107 |
1 files changed, 107 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/regulator/rohm,bd71847-regulator.yaml b/Documentation/devicetree/bindings/regulator/rohm,bd71847-regulator.yaml new file mode 100644 index 000000000..eeac32cd1 --- /dev/null +++ b/Documentation/devicetree/bindings/regulator/rohm,bd71847-regulator.yaml @@ -0,0 +1,107 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/regulator/rohm,bd71847-regulator.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ROHM BD71847 and BD71850 Power Management Integrated Circuit regulators + +maintainers: + - Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com> + +description: | + List of regulators provided by this controller. BD71847 regulators node + should be sub node of the BD71847 MFD node. See BD71847 MFD bindings at + Documentation/devicetree/bindings/mfd/rohm,bd71847-pmic.yaml + Regulator nodes should be named to BUCK_<number> and LDO_<number>. The + definition for each of these nodes is defined using the standard + binding for regulators at + Documentation/devicetree/bindings/regulator/regulator.txt. + Note that if BD71847 starts at RUN state you probably want to use + regulator-boot-on at least for BUCK5. LDO6 is supplied by it and it must + not be disabled by driver at startup. If BUCK5 is disabled at startup the + voltage monitoring for LDO5/LDO6 can cause PMIC to reset. + +#The valid names for BD71847 regulator nodes are: +#BUCK1, BUCK2, BUCK3, BUCK4, BUCK5, BUCK6 +#LDO1, LDO2, LDO3, LDO4, LDO5, LDO6 + +patternProperties: + "^LDO[1-6]$": + type: object + $ref: regulator.yaml# + description: + Properties for single LDO regulator. + + properties: + regulator-name: + pattern: "^ldo[1-6]$" + description: + should be "ldo1", ..., "ldo6" + + unevaluatedProperties: false + + "^BUCK[1-6]$": + type: object + $ref: regulator.yaml# + description: + Properties for single BUCK regulator. + + properties: + regulator-name: + pattern: "^buck[1-6]$" + description: + should be "buck1", ..., "buck6" + + rohm,dvs-run-voltage: + $ref: "/schemas/types.yaml#/definitions/uint32" + minimum: 0 + maximum: 1300000 + description: + PMIC default "RUN" state voltage in uV. See below table for + bucks which support this. 0 means disabled. + + rohm,dvs-idle-voltage: + $ref: "/schemas/types.yaml#/definitions/uint32" + minimum: 0 + maximum: 1300000 + description: + PMIC default "IDLE" state voltage in uV. See below table for + bucks which support this. 0 means disabled. + + rohm,dvs-suspend-voltage: + $ref: "/schemas/types.yaml#/definitions/uint32" + minimum: 0 + maximum: 1300000 + description: + PMIC default "SUSPEND" state voltage in uV. See below table for + bucks which support this. 0 means disabled. + + # Supported default DVS states: + # + # BD71847: + # buck | dvs-run-voltage | dvs-idle-voltage | dvs-suspend-voltage + # ---------------------------------------------------------------- + # 1 | supported | supported | supported + # ---------------------------------------------------------------- + # 2 | supported | supported | not supported + # ---------------------------------------------------------------- + # rest | not supported | not supported | not supported + + # BD718(47/50) power outputs can either be controlled by the PMIC internal + # hardware state machine or by software. If you need regulators to be + # turned ON/OFF for example based on PMIC_STBY_REQ line (which toggles + # PMIC HW state machine) - then you should set this property. + # Tradeoff is that then SW can't control the ON/OFF state for this + # regulator (other than invoking a PMIC state change). + rohm,no-regulator-enable-control: + description: | + Enable/Disable control of this regulator must be left to the + PMIC hardware state machine. + type: boolean + required: + - regulator-name + + unevaluatedProperties: false + +additionalProperties: false |