diff options
Diffstat (limited to '')
| -rw-r--r-- | Documentation/devicetree/bindings/soundwire/qcom,sdw.txt | 168 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/soundwire/soundwire-controller.yaml | 86 |
2 files changed, 254 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/soundwire/qcom,sdw.txt b/Documentation/devicetree/bindings/soundwire/qcom,sdw.txt new file mode 100644 index 000000000..b104be131 --- /dev/null +++ b/Documentation/devicetree/bindings/soundwire/qcom,sdw.txt @@ -0,0 +1,168 @@ +Qualcomm SoundWire Controller Bindings + + +This binding describes the Qualcomm SoundWire Controller along with its +board specific bus parameters. + +- compatible: + Usage: required + Value type: <stringlist> + Definition: must be "qcom,soundwire-v<MAJOR>.<MINOR>.<STEP>", + Example: + "qcom,soundwire-v1.3.0" + "qcom,soundwire-v1.5.0" + "qcom,soundwire-v1.5.1" + "qcom,soundwire-v1.6.0" +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: the base address and size of SoundWire controller + address space. + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: should specify the SoundWire Controller IRQ + +- clock-names: + Usage: required + Value type: <stringlist> + Definition: should be "iface" for SoundWire Controller interface clock + +- clocks: + Usage: required + Value type: <prop-encoded-array> + Definition: should specify the SoundWire Controller interface clock + +- #sound-dai-cells: + Usage: required + Value type: <u32> + Definition: must be 1 for digital audio interfaces on the controller. + +- qcom,dout-ports: + Usage: required + Value type: <u32> + Definition: must be count of data out ports + +- qcom,din-ports: + Usage: required + Value type: <u32> + Definition: must be count of data in ports + +- qcom,ports-offset1: + Usage: required + Value type: <prop-encoded-array> + Definition: should specify payload transport window offset1 of each + data port. Out ports followed by In ports. + More info in MIPI Alliance SoundWire 1.0 Specifications. + +- qcom,ports-offset2: + Usage: required + Value type: <prop-encoded-array> + Definition: should specify payload transport window offset2 of each + data port. Out ports followed by In ports. + More info in MIPI Alliance SoundWire 1.0 Specifications. + +- qcom,ports-sinterval-low: + Usage: required + Value type: <prop-encoded-array> + Definition: should be sample interval low of each data port. + Out ports followed by In ports. Used for Sample Interval + calculation. + More info in MIPI Alliance SoundWire 1.0 Specifications. + +- qcom,ports-word-length: + Usage: optional + Value type: <prop-encoded-array> + Definition: should be size of payload channel sample. + More info in MIPI Alliance SoundWire 1.0 Specifications. + +- qcom,ports-block-pack-mode: + Usage: optional + Value type: <prop-encoded-array> + Definition: should be 0 or 1 to indicate the block packing mode. + 0 to indicate Blocks are per Channel + 1 to indicate Blocks are per Port. + Out ports followed by In ports. + More info in MIPI Alliance SoundWire 1.0 Specifications. + +- qcom,ports-block-group-count: + Usage: optional + Value type: <prop-encoded-array> + Definition: should be in range 1 to 4 to indicate how many sample + intervals are combined into a payload. + Out ports followed by In ports. + More info in MIPI Alliance SoundWire 1.0 Specifications. + +- qcom,ports-lane-control: + Usage: optional + Value type: <prop-encoded-array> + Definition: should be in range 0 to 7 to identify which data lane + the data port uses. + Out ports followed by In ports. + More info in MIPI Alliance SoundWire 1.0 Specifications. + +- qcom,ports-hstart: + Usage: optional + Value type: <prop-encoded-array> + Definition: should be number identifying lowerst numbered coloum in + SoundWire Frame, i.e. left edge of the Transport sub-frame + for each port. Values between 0 and 15 are valid. + Out ports followed by In ports. + More info in MIPI Alliance SoundWire 1.0 Specifications. + +- qcom,ports-hstop: + Usage: optional + Value type: <prop-encoded-array> + Definition: should be number identifying highest numbered coloum in + SoundWire Frame, i.e. the right edge of the Transport + sub-frame for each port. Values between 0 and 15 are valid. + Out ports followed by In ports. + More info in MIPI Alliance SoundWire 1.0 Specifications. + +- qcom,dports-type: + Usage: optional + Value type: <prop-encoded-array> + Definition: should be one of the following types + 0 for reduced port + 1 for simple ports + 2 for full port + Out ports followed by In ports. + More info in MIPI Alliance SoundWire 1.0 Specifications. + +Note: + More Information on detail of encoding of these fields can be +found in MIPI Alliance SoundWire 1.0 Specifications. + += SoundWire devices +Each subnode of the bus represents SoundWire device attached to it. +The properties of these nodes are defined by the individual bindings. + += EXAMPLE +The following example represents a SoundWire controller on DB845c board +which has controller integrated inside WCD934x codec on SDM845 SoC. + +soundwire: soundwire@c85 { + compatible = "qcom,soundwire-v1.3.0"; + reg = <0xc85 0x20>; + interrupts = <20 IRQ_TYPE_EDGE_RISING>; + clocks = <&wcc>; + clock-names = "iface"; + #sound-dai-cells = <1>; + qcom,dports-type = <0>; + qcom,dout-ports = <6>; + qcom,din-ports = <2>; + qcom,ports-sinterval-low = /bits/ 8 <0x07 0x1F 0x3F 0x7 0x1F 0x3F 0x0F 0x0F>; + qcom,ports-offset1 = /bits/ 8 <0x01 0x02 0x0C 0x6 0x12 0x0D 0x07 0x0A >; + qcom,ports-offset2 = /bits/ 8 <0x00 0x00 0x1F 0x00 0x00 0x1F 0x00 0x00>; + + /* Left Speaker */ + left{ + .... + }; + + /* Right Speaker */ + right{ + .... + }; +}; diff --git a/Documentation/devicetree/bindings/soundwire/soundwire-controller.yaml b/Documentation/devicetree/bindings/soundwire/soundwire-controller.yaml new file mode 100644 index 000000000..4aad121ef --- /dev/null +++ b/Documentation/devicetree/bindings/soundwire/soundwire-controller.yaml @@ -0,0 +1,86 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/soundwire/soundwire-controller.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: SoundWire Controller Generic Binding + +maintainers: + - Srinivas Kandagatla <srinivas.kandagatla@linaro.org> + - Vinod Koul <vkoul@kernel.org> + +description: | + SoundWire busses can be described with a node for the SoundWire controller + device and a set of child nodes for each SoundWire slave on the bus. + +properties: + $nodename: + pattern: "^soundwire(@.*)?$" + + "#address-cells": + const: 2 + + "#size-cells": + const: 0 + +patternProperties: + "^.*@[0-9a-f],[0-9a-f]$": + type: object + + properties: + compatible: + pattern: "^sdw[0-9a-f]{1}[0-9a-f]{4}[0-9a-f]{4}[0-9a-f]{2}$" + description: Is the textual representation of SoundWire Enumeration + address. compatible string should contain SoundWire Version ID, + Manufacturer ID, Part ID and Class ID in order and shall be in + lower-case hexadecimal with leading zeroes. + Valid sizes of these fields are + Version ID is 1 nibble, number '0x1' represents SoundWire 1.0 + and '0x2' represents SoundWire 1.1 and so on. + MFD is 4 nibbles + PID is 4 nibbles + CID is 2 nibbles + More Information on detail of encoding of these fields can be + found in MIPI Alliance DisCo & SoundWire 1.0 Specifications. + + reg: + maxItems: 1 + description: + Link ID followed by Instance ID of SoundWire Device Address. + + required: + - compatible + - reg + +required: + - "#address-cells" + - "#size-cells" + +additionalProperties: true + +examples: + - | + soundwire@c2d0000 { + #address-cells = <2>; + #size-cells = <0>; + reg = <0x0c2d0000 0x2000>; + + speaker@0,1 { + compatible = "sdw10217201000"; + reg = <0 1>; + powerdown-gpios = <&wcdpinctrl 2 0>; + #thermal-sensor-cells = <0>; + #sound-dai-cells = <0>; + }; + + speaker@0,2 { + compatible = "sdw10217201000"; + reg = <0 2>; + powerdown-gpios = <&wcdpinctrl 2 0>; + #thermal-sensor-cells = <0>; + #sound-dai-cells = <0>; + }; + }; + +... |