diff options
Diffstat (limited to '')
| -rw-r--r-- | Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt | 87 |
1 files changed, 87 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt new file mode 100644 index 000000000..415ccdd74 --- /dev/null +++ b/Documentation/devicetree/bindings/ufs/ufshcd-pltfrm.txt @@ -0,0 +1,87 @@ +* Universal Flash Storage (UFS) Host Controller + +UFSHC nodes are defined to describe on-chip UFS host controllers. +Each UFS controller instance should have its own node. + +Required properties: +- compatible : must contain "jedec,ufs-1.1" or "jedec,ufs-2.0" + + For Qualcomm SoCs must contain, as below, an + SoC-specific compatible along with "qcom,ufshc" and + the appropriate jedec string: + "qcom,msm8994-ufshc", "qcom,ufshc", "jedec,ufs-2.0" + "qcom,msm8996-ufshc", "qcom,ufshc", "jedec,ufs-2.0" + "qcom,msm8998-ufshc", "qcom,ufshc", "jedec,ufs-2.0" + "qcom,sdm845-ufshc", "qcom,ufshc", "jedec,ufs-2.0" + "qcom,sm8150-ufshc", "qcom,ufshc", "jedec,ufs-2.0" +- interrupts : <interrupt mapping for UFS host controller IRQ> +- reg : <registers mapping> + +Optional properties: +- phys : phandle to UFS PHY node +- phy-names : the string "ufsphy" when is found in a node, along + with "phys" attribute, provides phandle to UFS PHY node +- vdd-hba-supply : phandle to UFS host controller supply regulator node +- vcc-supply : phandle to VCC supply regulator node +- vccq-supply : phandle to VCCQ supply regulator node +- vccq2-supply : phandle to VCCQ2 supply regulator node +- vcc-supply-1p8 : For embedded UFS devices, valid VCC range is 1.7-1.95V + or 2.7-3.6V. This boolean property when set, specifies + to use low voltage range of 1.7-1.95V. Note for external + UFS cards this property is invalid and valid VCC range is + always 2.7-3.6V. +- vcc-max-microamp : specifies max. load that can be drawn from vcc supply +- vccq-max-microamp : specifies max. load that can be drawn from vccq supply +- vccq2-max-microamp : specifies max. load that can be drawn from vccq2 supply + +- clocks : List of phandle and clock specifier pairs +- clock-names : List of clock input name strings sorted in the same + order as the clocks property. + "ref_clk" indicates reference clock frequency. + UFS host supplies reference clock to UFS device and UFS device + specification allows host to provide one of the 4 frequencies (19.2 MHz, + 26 MHz, 38.4 MHz, 52MHz) for reference clock. This "ref_clk" entry is + parsed and used to update the reference clock setting in device. + Defaults to 26 MHz(as per specification) if not specified by host. +- freq-table-hz : Array of <min max> operating frequencies stored in the same + order as the clocks property. If this property is not + defined or a value in the array is "0" then it is assumed + that the frequency is set by the parent clock or a + fixed rate clock source. +-lanes-per-direction : number of lanes available per direction - either 1 or 2. + Note that it is assume same number of lanes is used both + directions at once. If not specified, default is 2 lanes per direction. +- #reset-cells : Must be <1> for Qualcomm UFS controllers that expose + PHY reset from the UFS controller. +- resets : reset node register +- reset-names : describe reset node register, the "rst" corresponds to reset the whole UFS IP. +- reset-gpios : A phandle and gpio specifier denoting the GPIO connected + to the RESET pin of the UFS memory device. + +Note: If above properties are not defined it can be assumed that the supply +regulators or clocks are always on. + +Example: + ufshc@fc598000 { + compatible = "jedec,ufs-1.1"; + reg = <0xfc598000 0x800>; + interrupts = <0 28 0>; + + vdd-hba-supply = <&xxx_reg0>; + vcc-supply = <&xxx_reg1>; + vcc-supply-1p8; + vccq-supply = <&xxx_reg2>; + vccq2-supply = <&xxx_reg3>; + vcc-max-microamp = 500000; + vccq-max-microamp = 200000; + vccq2-max-microamp = 200000; + + clocks = <&core 0>, <&ref 0>, <&phy 0>, <&iface 0>; + clock-names = "core_clk", "ref_clk", "phy_clk", "iface_clk"; + freq-table-hz = <100000000 200000000>, <0 0>, <0 0>, <0 0>; + resets = <&reset 0 1>; + reset-names = "rst"; + phys = <&ufsphy1>; + phy-names = "ufsphy"; + #reset-cells = <1>; + }; |