diff options
Diffstat (limited to '')
| -rw-r--r-- | Documentation/devicetree/bindings/usb/dwc3.txt | 128 |
1 files changed, 128 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/usb/dwc3.txt b/Documentation/devicetree/bindings/usb/dwc3.txt new file mode 100644 index 000000000..1aae2b616 --- /dev/null +++ b/Documentation/devicetree/bindings/usb/dwc3.txt @@ -0,0 +1,128 @@ +synopsys DWC3 CORE + +DWC3- USB3 CONTROLLER. Complies to the generic USB binding properties + as described in 'usb/generic.txt' + +Required properties: + - compatible: must be "snps,dwc3" + - reg : Address and length of the register set for the device + - interrupts: Interrupts used by the dwc3 controller. + - clock-names: list of clock names. Ideally should be "ref", + "bus_early", "suspend" but may be less or more. + - clocks: list of phandle and clock specifier pairs corresponding to + entries in the clock-names property. + +Exception for clocks: + clocks are optional if the parent node (i.e. glue-layer) is compatible to + one of the following: + "cavium,octeon-7130-usb-uctl" + "qcom,dwc3" + "samsung,exynos5250-dwusb3" + "samsung,exynos5433-dwusb3" + "samsung,exynos7-dwusb3" + "sprd,sc9860-dwc3" + "st,stih407-dwc3" + "ti,am437x-dwc3" + "ti,dwc3" + "ti,keystone-dwc3" + "rockchip,rk3399-dwc3" + "xlnx,zynqmp-dwc3" + +Optional properties: + - usb-phy : array of phandle for the PHY device. The first element + in the array is expected to be a handle to the USB2/HS PHY and + the second element is expected to be a handle to the USB3/SS PHY + - phys: from the *Generic PHY* bindings + - phy-names: from the *Generic PHY* bindings; supported names are "usb2-phy" + or "usb3-phy". + - resets: set of phandle and reset specifier pairs + - snps,usb2-lpm-disable: indicate if we don't want to enable USB2 HW LPM + - snps,usb3_lpm_capable: determines if platform is USB3 LPM capable + - snps,dis-start-transfer-quirk: when set, disable isoc START TRANSFER command + failure SW work-around for DWC_usb31 version 1.70a-ea06 + and prior. + - snps,disable_scramble_quirk: true when SW should disable data scrambling. + Only really useful for FPGA builds. + - snps,has-lpm-erratum: true when DWC3 was configured with LPM Erratum enabled + - snps,lpm-nyet-threshold: LPM NYET threshold + - snps,u2exit_lfps_quirk: set if we want to enable u2exit lfps quirk + - snps,u2ss_inp3_quirk: set if we enable P3 OK for U2/SS Inactive quirk + - snps,req_p1p2p3_quirk: when set, the core will always request for + P1/P2/P3 transition sequence. + - snps,del_p1p2p3_quirk: when set core will delay P1/P2/P3 until a certain + amount of 8B10B errors occur. + - snps,del_phy_power_chg_quirk: when set core will delay PHY power change + from P0 to P1/P2/P3. + - snps,lfps_filter_quirk: when set core will filter LFPS reception. + - snps,rx_detect_poll_quirk: when set core will disable a 400us delay to start + Polling LFPS after RX.Detect. + - snps,tx_de_emphasis_quirk: when set core will set Tx de-emphasis value. + - snps,tx_de_emphasis: the value driven to the PHY is controlled by the + LTSSM during USB3 Compliance mode. + - snps,dis_u3_susphy_quirk: when set core will disable USB3 suspend phy. + - snps,dis_u2_susphy_quirk: when set core will disable USB2 suspend phy. + - snps,dis_enblslpm_quirk: when set clears the enblslpm in GUSB2PHYCFG, + disabling the suspend signal to the PHY. + - snps,dis-u1-entry-quirk: set if link entering into U1 needs to be disabled. + - snps,dis-u2-entry-quirk: set if link entering into U2 needs to be disabled. + - snps,dis_rxdet_inp3_quirk: when set core will disable receiver detection + in PHY P3 power state. + - snps,dis-u2-freeclk-exists-quirk: when set, clear the u2_freeclk_exists + in GUSB2PHYCFG, specify that USB2 PHY doesn't provide + a free-running PHY clock. + - snps,dis-del-phy-power-chg-quirk: when set core will change PHY power + from P0 to P1/P2/P3 without delay. + - snps,dis-tx-ipgap-linecheck-quirk: when set, disable u2mac linestate check + during HS transmit. + - snps,parkmode-disable-ss-quirk: when set, all SuperSpeed bus instances in + park mode are disabled. + - snps,dis_metastability_quirk: when set, disable metastability workaround. + CAUTION: use only if you are absolutely sure of it. + - snps,dis-split-quirk: when set, change the way URBs are handled by the + driver. Needed to avoid -EPROTO errors with usbhid + on some devices (Hikey 970). + - snps,is-utmi-l1-suspend: true when DWC3 asserts output signal + utmi_l1_suspend_n, false when asserts utmi_sleep_n + - snps,hird-threshold: HIRD threshold + - snps,hsphy_interface: High-Speed PHY interface selection between "utmi" for + UTMI+ and "ulpi" for ULPI when the DWC_USB3_HSPHY_INTERFACE has value 3. + - snps,quirk-frame-length-adjustment: Value for GFLADJ_30MHZ field of GFLADJ + register for post-silicon frame length adjustment when the + fladj_30mhz_sdbnd signal is invalid or incorrect. + - snps,rx-thr-num-pkt-prd: periodic ESS RX packet threshold count - host mode + only. Set this and rx-max-burst-prd to a valid, + non-zero value 1-16 (DWC_usb31 programming guide + section 1.2.4) to enable periodic ESS RX threshold. + - snps,rx-max-burst-prd: max periodic ESS RX burst size - host mode only. Set + this and rx-thr-num-pkt-prd to a valid, non-zero value + 1-16 (DWC_usb31 programming guide section 1.2.4) to + enable periodic ESS RX threshold. + - snps,tx-thr-num-pkt-prd: periodic ESS TX packet threshold count - host mode + only. Set this and tx-max-burst-prd to a valid, + non-zero value 1-16 (DWC_usb31 programming guide + section 1.2.3) to enable periodic ESS TX threshold. + - snps,tx-max-burst-prd: max periodic ESS TX burst size - host mode only. Set + this and tx-thr-num-pkt-prd to a valid, non-zero value + 1-16 (DWC_usb31 programming guide section 1.2.3) to + enable periodic ESS TX threshold. + + - <DEPRECATED> tx-fifo-resize: determines if the FIFO *has* to be reallocated. + - snps,incr-burst-type-adjustment: Value for INCR burst type of GSBUSCFG0 + register, undefined length INCR burst type enable and INCRx type. + When just one value, which means INCRX burst mode enabled. When + more than one value, which means undefined length INCR burst type + enabled. The values can be 1, 4, 8, 16, 32, 64, 128 and 256. + + - in addition all properties from usb-xhci.txt from the current directory are + supported as well + + +This is usually a subnode to DWC3 glue to which it is connected. + +dwc3@4a030000 { + compatible = "snps,dwc3"; + reg = <0x4a030000 0xcfff>; + interrupts = <0 92 4> + usb-phy = <&usb2_phy>, <&usb3,phy>; + snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>; +}; |