summaryrefslogtreecommitdiffstats
path: root/Documentation/driver-api/gpio/driver.rst
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/driver-api/gpio/driver.rst')
-rw-r--r--Documentation/driver-api/gpio/driver.rst645
1 files changed, 645 insertions, 0 deletions
diff --git a/Documentation/driver-api/gpio/driver.rst b/Documentation/driver-api/gpio/driver.rst
new file mode 100644
index 000000000..072a74550
--- /dev/null
+++ b/Documentation/driver-api/gpio/driver.rst
@@ -0,0 +1,645 @@
+=====================
+GPIO Driver Interface
+=====================
+
+This document serves as a guide for writers of GPIO chip drivers.
+
+Each GPIO controller driver needs to include the following header, which defines
+the structures used to define a GPIO driver::
+
+ #include <linux/gpio/driver.h>
+
+
+Internal Representation of GPIOs
+================================
+
+A GPIO chip handles one or more GPIO lines. To be considered a GPIO chip, the
+lines must conform to the definition: General Purpose Input/Output. If the
+line is not general purpose, it is not GPIO and should not be handled by a
+GPIO chip. The use case is the indicative: certain lines in a system may be
+called GPIO but serve a very particular purpose thus not meeting the criteria
+of a general purpose I/O. On the other hand a LED driver line may be used as a
+GPIO and should therefore still be handled by a GPIO chip driver.
+
+Inside a GPIO driver, individual GPIO lines are identified by their hardware
+number, sometime also referred to as ``offset``, which is a unique number
+between 0 and n-1, n being the number of GPIOs managed by the chip.
+
+The hardware GPIO number should be something intuitive to the hardware, for
+example if a system uses a memory-mapped set of I/O-registers where 32 GPIO
+lines are handled by one bit per line in a 32-bit register, it makes sense to
+use hardware offsets 0..31 for these, corresponding to bits 0..31 in the
+register.
+
+This number is purely internal: the hardware number of a particular GPIO
+line is never made visible outside of the driver.
+
+On top of this internal number, each GPIO line also needs to have a global
+number in the integer GPIO namespace so that it can be used with the legacy GPIO
+interface. Each chip must thus have a "base" number (which can be automatically
+assigned), and for each GPIO line the global number will be (base + hardware
+number). Although the integer representation is considered deprecated, it still
+has many users and thus needs to be maintained.
+
+So for example one platform could use global numbers 32-159 for GPIOs, with a
+controller defining 128 GPIOs at a "base" of 32 ; while another platform uses
+global numbers 0..63 with one set of GPIO controllers, 64-79 with another type
+of GPIO controller, and on one particular board 80-95 with an FPGA. The legacy
+numbers need not be contiguous; either of those platforms could also use numbers
+2000-2063 to identify GPIO lines in a bank of I2C GPIO expanders.
+
+
+Controller Drivers: gpio_chip
+=============================
+
+In the gpiolib framework each GPIO controller is packaged as a "struct
+gpio_chip" (see <linux/gpio/driver.h> for its complete definition) with members
+common to each controller of that type, these should be assigned by the
+driver code:
+
+ - methods to establish GPIO line direction
+ - methods used to access GPIO line values
+ - method to set electrical configuration for a given GPIO line
+ - method to return the IRQ number associated to a given GPIO line
+ - flag saying whether calls to its methods may sleep
+ - optional line names array to identify lines
+ - optional debugfs dump method (showing extra state information)
+ - optional base number (will be automatically assigned if omitted)
+ - optional label for diagnostics and GPIO chip mapping using platform data
+
+The code implementing a gpio_chip should support multiple instances of the
+controller, preferably using the driver model. That code will configure each
+gpio_chip and issue gpiochip_add(), gpiochip_add_data(), or
+devm_gpiochip_add_data(). Removing a GPIO controller should be rare; use
+gpiochip_remove() when it is unavoidable.
+
+Often a gpio_chip is part of an instance-specific structure with states not
+exposed by the GPIO interfaces, such as addressing, power management, and more.
+Chips such as audio codecs will have complex non-GPIO states.
+
+Any debugfs dump method should normally ignore lines which haven't been
+requested. They can use gpiochip_is_requested(), which returns either
+NULL or the label associated with that GPIO line when it was requested.
+
+Realtime considerations: the GPIO driver should not use spinlock_t or any
+sleepable APIs (like PM runtime) in its gpio_chip implementation (.get/.set
+and direction control callbacks) if it is expected to call GPIO APIs from
+atomic context on realtime kernels (inside hard IRQ handlers and similar
+contexts). Normally this should not be required.
+
+
+GPIO electrical configuration
+-----------------------------
+
+GPIO lines can be configured for several electrical modes of operation by using
+the .set_config() callback. Currently this API supports setting:
+
+- Debouncing
+- Single-ended modes (open drain/open source)
+- Pull up and pull down resistor enablement
+
+These settings are described below.
+
+The .set_config() callback uses the same enumerators and configuration
+semantics as the generic pin control drivers. This is not a coincidence: it is
+possible to assign the .set_config() to the function gpiochip_generic_config()
+which will result in pinctrl_gpio_set_config() being called and eventually
+ending up in the pin control back-end "behind" the GPIO controller, usually
+closer to the actual pins. This way the pin controller can manage the below
+listed GPIO configurations.
+
+If a pin controller back-end is used, the GPIO controller or hardware
+description needs to provide "GPIO ranges" mapping the GPIO line offsets to pin
+numbers on the pin controller so they can properly cross-reference each other.
+
+
+GPIO lines with debounce support
+--------------------------------
+
+Debouncing is a configuration set to a pin indicating that it is connected to
+a mechanical switch or button, or similar that may bounce. Bouncing means the
+line is pulled high/low quickly at very short intervals for mechanical
+reasons. This can result in the value being unstable or irqs fireing repeatedly
+unless the line is debounced.
+
+Debouncing in practice involves setting up a timer when something happens on
+the line, wait a little while and then sample the line again, so see if it
+still has the same value (low or high). This could also be repeated by a clever
+state machine, waiting for a line to become stable. In either case, it sets
+a certain number of milliseconds for debouncing, or just "on/off" if that time
+is not configurable.
+
+
+GPIO lines with open drain/source support
+-----------------------------------------
+
+Open drain (CMOS) or open collector (TTL) means the line is not actively driven
+high: instead you provide the drain/collector as output, so when the transistor
+is not open, it will present a high-impedance (tristate) to the external rail::
+
+
+ CMOS CONFIGURATION TTL CONFIGURATION
+
+ ||--- out +--- out
+ in ----|| |/
+ ||--+ in ----|
+ | |\
+ GND GND
+
+This configuration is normally used as a way to achieve one of two things:
+
+- Level-shifting: to reach a logical level higher than that of the silicon
+ where the output resides.
+
+- Inverse wire-OR on an I/O line, for example a GPIO line, making it possible
+ for any driving stage on the line to drive it low even if any other output
+ to the same line is simultaneously driving it high. A special case of this
+ is driving the SCL and SDA lines of an I2C bus, which is by definition a
+ wire-OR bus.
+
+Both use cases require that the line be equipped with a pull-up resistor. This
+resistor will make the line tend to high level unless one of the transistors on
+the rail actively pulls it down.
+
+The level on the line will go as high as the VDD on the pull-up resistor, which
+may be higher than the level supported by the transistor, achieving a
+level-shift to the higher VDD.
+
+Integrated electronics often have an output driver stage in the form of a CMOS
+"totem-pole" with one N-MOS and one P-MOS transistor where one of them drives
+the line high and one of them drives the line low. This is called a push-pull
+output. The "totem-pole" looks like so::
+
+ VDD
+ |
+ OD ||--+
+ +--/ ---o|| P-MOS-FET
+ | ||--+
+ IN --+ +----- out
+ | ||--+
+ +--/ ----|| N-MOS-FET
+ OS ||--+
+ |
+ GND
+
+The desired output signal (e.g. coming directly from some GPIO output register)
+arrives at IN. The switches named "OD" and "OS" are normally closed, creating
+a push-pull circuit.
+
+Consider the little "switches" named "OD" and "OS" that enable/disable the
+P-MOS or N-MOS transistor right after the split of the input. As you can see,
+either transistor will go totally numb if this switch is open. The totem-pole
+is then halved and give high impedance instead of actively driving the line
+high or low respectively. That is usually how software-controlled open
+drain/source works.
+
+Some GPIO hardware come in open drain / open source configuration. Some are
+hard-wired lines that will only support open drain or open source no matter
+what: there is only one transistor there. Some are software-configurable:
+by flipping a bit in a register the output can be configured as open drain
+or open source, in practice by flicking open the switches labeled "OD" and "OS"
+in the drawing above.
+
+By disabling the P-MOS transistor, the output can be driven between GND and
+high impedance (open drain), and by disabling the N-MOS transistor, the output
+can be driven between VDD and high impedance (open source). In the first case,
+a pull-up resistor is needed on the outgoing rail to complete the circuit, and
+in the second case, a pull-down resistor is needed on the rail.
+
+Hardware that supports open drain or open source or both, can implement a
+special callback in the gpio_chip: .set_config() that takes a generic
+pinconf packed value telling whether to configure the line as open drain,
+open source or push-pull. This will happen in response to the
+GPIO_OPEN_DRAIN or GPIO_OPEN_SOURCE flag set in the machine file, or coming
+from other hardware descriptions.
+
+If this state can not be configured in hardware, i.e. if the GPIO hardware does
+not support open drain/open source in hardware, the GPIO library will instead
+use a trick: when a line is set as output, if the line is flagged as open
+drain, and the IN output value is low, it will be driven low as usual. But
+if the IN output value is set to high, it will instead *NOT* be driven high,
+instead it will be switched to input, as input mode is high impedance, thus
+achieveing an "open drain emulation" of sorts: electrically the behaviour will
+be identical, with the exception of possible hardware glitches when switching
+the mode of the line.
+
+For open source configuration the same principle is used, just that instead
+of actively driving the line low, it is set to input.
+
+
+GPIO lines with pull up/down resistor support
+---------------------------------------------
+
+A GPIO line can support pull-up/down using the .set_config() callback. This
+means that a pull up or pull-down resistor is available on the output of the
+GPIO line, and this resistor is software controlled.
+
+In discrete designs, a pull-up or pull-down resistor is simply soldered on
+the circuit board. This is not something we deal with or model in software. The
+most you will think about these lines is that they will very likely be
+configured as open drain or open source (see the section above).
+
+The .set_config() callback can only turn pull up or down on and off, and will
+no have any semantic knowledge about the resistance used. It will only say
+switch a bit in a register enabling or disabling pull-up or pull-down.
+
+If the GPIO line supports shunting in different resistance values for the
+pull-up or pull-down resistor, the GPIO chip callback .set_config() will not
+suffice. For these complex use cases, a combined GPIO chip and pin controller
+need to be implemented, as the pin config interface of a pin controller
+supports more versatile control over electrical properties and can handle
+different pull-up or pull-down resistance values.
+
+
+GPIO drivers providing IRQs
+===========================
+
+It is custom that GPIO drivers (GPIO chips) are also providing interrupts,
+most often cascaded off a parent interrupt controller, and in some special
+cases the GPIO logic is melded with a SoC's primary interrupt controller.
+
+The IRQ portions of the GPIO block are implemented using an irq_chip, using
+the header <linux/irq.h>. So this combined driver is utilizing two sub-
+systems simultaneously: gpio and irq.
+
+It is legal for any IRQ consumer to request an IRQ from any irqchip even if it
+is a combined GPIO+IRQ driver. The basic premise is that gpio_chip and
+irq_chip are orthogonal, and offering their services independent of each
+other.
+
+gpiod_to_irq() is just a convenience function to figure out the IRQ for a
+certain GPIO line and should not be relied upon to have been called before
+the IRQ is used.
+
+Always prepare the hardware and make it ready for action in respective
+callbacks from the GPIO and irq_chip APIs. Do not rely on gpiod_to_irq() having
+been called first.
+
+We can divide GPIO irqchips in two broad categories:
+
+- CASCADED INTERRUPT CHIPS: this means that the GPIO chip has one common
+ interrupt output line, which is triggered by any enabled GPIO line on that
+ chip. The interrupt output line will then be routed to an parent interrupt
+ controller one level up, in the most simple case the systems primary
+ interrupt controller. This is modeled by an irqchip that will inspect bits
+ inside the GPIO controller to figure out which line fired it. The irqchip
+ part of the driver needs to inspect registers to figure this out and it
+ will likely also need to acknowledge that it is handling the interrupt
+ by clearing some bit (sometime implicitly, by just reading a status
+ register) and it will often need to set up the configuration such as
+ edge sensitivity (rising or falling edge, or high/low level interrupt for
+ example).
+
+- HIERARCHICAL INTERRUPT CHIPS: this means that each GPIO line has a dedicated
+ irq line to a parent interrupt controller one level up. There is no need
+ to inquire the GPIO hardware to figure out which line has fired, but it
+ may still be necessary to acknowledge the interrupt and set up configuration
+ such as edge sensitivity.
+
+Realtime considerations: a realtime compliant GPIO driver should not use
+spinlock_t or any sleepable APIs (like PM runtime) as part of its irqchip
+implementation.
+
+- spinlock_t should be replaced with raw_spinlock_t.[1]
+- If sleepable APIs have to be used, these can be done from the .irq_bus_lock()
+ and .irq_bus_unlock() callbacks, as these are the only slowpath callbacks
+ on an irqchip. Create the callbacks if needed.[2]
+
+
+Cascaded GPIO irqchips
+----------------------
+
+Cascaded GPIO irqchips usually fall in one of three categories:
+
+- CHAINED CASCADED GPIO IRQCHIPS: these are usually the type that is embedded on
+ an SoC. This means that there is a fast IRQ flow handler for the GPIOs that
+ gets called in a chain from the parent IRQ handler, most typically the
+ system interrupt controller. This means that the GPIO irqchip handler will
+ be called immediately from the parent irqchip, while holding the IRQs
+ disabled. The GPIO irqchip will then end up calling something like this
+ sequence in its interrupt handler::
+
+ static irqreturn_t foo_gpio_irq(int irq, void *data)
+ chained_irq_enter(...);
+ generic_handle_irq(...);
+ chained_irq_exit(...);
+
+ Chained GPIO irqchips typically can NOT set the .can_sleep flag on
+ struct gpio_chip, as everything happens directly in the callbacks: no
+ slow bus traffic like I2C can be used.
+
+ Realtime considerations: Note that chained IRQ handlers will not be forced
+ threaded on -RT. As a result, spinlock_t or any sleepable APIs (like PM
+ runtime) can't be used in a chained IRQ handler.
+
+ If required (and if it can't be converted to the nested threaded GPIO irqchip,
+ see below) a chained IRQ handler can be converted to generic irq handler and
+ this way it will become a threaded IRQ handler on -RT and a hard IRQ handler
+ on non-RT (for example, see [3]).
+
+ The generic_handle_irq() is expected to be called with IRQ disabled,
+ so the IRQ core will complain if it is called from an IRQ handler which is
+ forced to a thread. The "fake?" raw lock can be used to work around this
+ problem::
+
+ raw_spinlock_t wa_lock;
+ static irqreturn_t omap_gpio_irq_handler(int irq, void *gpiobank)
+ unsigned long wa_lock_flags;
+ raw_spin_lock_irqsave(&bank->wa_lock, wa_lock_flags);
+ generic_handle_irq(irq_find_mapping(bank->chip.irq.domain, bit));
+ raw_spin_unlock_irqrestore(&bank->wa_lock, wa_lock_flags);
+
+- GENERIC CHAINED GPIO IRQCHIPS: these are the same as "CHAINED GPIO irqchips",
+ but chained IRQ handlers are not used. Instead GPIO IRQs dispatching is
+ performed by generic IRQ handler which is configured using request_irq().
+ The GPIO irqchip will then end up calling something like this sequence in
+ its interrupt handler::
+
+ static irqreturn_t gpio_rcar_irq_handler(int irq, void *dev_id)
+ for each detected GPIO IRQ
+ generic_handle_irq(...);
+
+ Realtime considerations: this kind of handlers will be forced threaded on -RT,
+ and as result the IRQ core will complain that generic_handle_irq() is called
+ with IRQ enabled and the same work-around as for "CHAINED GPIO irqchips" can
+ be applied.
+
+- NESTED THREADED GPIO IRQCHIPS: these are off-chip GPIO expanders and any
+ other GPIO irqchip residing on the other side of a sleeping bus such as I2C
+ or SPI.
+
+ Of course such drivers that need slow bus traffic to read out IRQ status and
+ similar, traffic which may in turn incur other IRQs to happen, cannot be
+ handled in a quick IRQ handler with IRQs disabled. Instead they need to spawn
+ a thread and then mask the parent IRQ line until the interrupt is handled
+ by the driver. The hallmark of this driver is to call something like
+ this in its interrupt handler::
+
+ static irqreturn_t foo_gpio_irq(int irq, void *data)
+ ...
+ handle_nested_irq(irq);
+
+ The hallmark of threaded GPIO irqchips is that they set the .can_sleep
+ flag on struct gpio_chip to true, indicating that this chip may sleep
+ when accessing the GPIOs.
+
+ These kinds of irqchips are inherently realtime tolerant as they are
+ already set up to handle sleeping contexts.
+
+
+Infrastructure helpers for GPIO irqchips
+----------------------------------------
+
+To help out in handling the set-up and management of GPIO irqchips and the
+associated irqdomain and resource allocation callbacks. These are activated
+by selecting the Kconfig symbol GPIOLIB_IRQCHIP. If the symbol
+IRQ_DOMAIN_HIERARCHY is also selected, hierarchical helpers will also be
+provided. A big portion of overhead code will be managed by gpiolib,
+under the assumption that your interrupts are 1-to-1-mapped to the
+GPIO line index:
+
+.. csv-table::
+ :header: GPIO line offset, Hardware IRQ
+
+ 0,0
+ 1,1
+ 2,2
+ ...,...
+ ngpio-1, ngpio-1
+
+
+If some GPIO lines do not have corresponding IRQs, the bitmask valid_mask
+and the flag need_valid_mask in gpio_irq_chip can be used to mask off some
+lines as invalid for associating with IRQs.
+
+The preferred way to set up the helpers is to fill in the
+struct gpio_irq_chip inside struct gpio_chip before adding the gpio_chip.
+If you do this, the additional irq_chip will be set up by gpiolib at the
+same time as setting up the rest of the GPIO functionality. The following
+is a typical example of a cascaded interrupt handler using gpio_irq_chip:
+
+.. code-block:: c
+
+ /* Typical state container with dynamic irqchip */
+ struct my_gpio {
+ struct gpio_chip gc;
+ struct irq_chip irq;
+ };
+
+ int irq; /* from platform etc */
+ struct my_gpio *g;
+ struct gpio_irq_chip *girq;
+
+ /* Set up the irqchip dynamically */
+ g->irq.name = "my_gpio_irq";
+ g->irq.irq_ack = my_gpio_ack_irq;
+ g->irq.irq_mask = my_gpio_mask_irq;
+ g->irq.irq_unmask = my_gpio_unmask_irq;
+ g->irq.irq_set_type = my_gpio_set_irq_type;
+
+ /* Get a pointer to the gpio_irq_chip */
+ girq = &g->gc.irq;
+ girq->chip = &g->irq;
+ girq->parent_handler = ftgpio_gpio_irq_handler;
+ girq->num_parents = 1;
+ girq->parents = devm_kcalloc(dev, 1, sizeof(*girq->parents),
+ GFP_KERNEL);
+ if (!girq->parents)
+ return -ENOMEM;
+ girq->default_type = IRQ_TYPE_NONE;
+ girq->handler = handle_bad_irq;
+ girq->parents[0] = irq;
+
+ return devm_gpiochip_add_data(dev, &g->gc, g);
+
+The helper support using hierarchical interrupt controllers as well.
+In this case the typical set-up will look like this:
+
+.. code-block:: c
+
+ /* Typical state container with dynamic irqchip */
+ struct my_gpio {
+ struct gpio_chip gc;
+ struct irq_chip irq;
+ struct fwnode_handle *fwnode;
+ };
+
+ int irq; /* from platform etc */
+ struct my_gpio *g;
+ struct gpio_irq_chip *girq;
+
+ /* Set up the irqchip dynamically */
+ g->irq.name = "my_gpio_irq";
+ g->irq.irq_ack = my_gpio_ack_irq;
+ g->irq.irq_mask = my_gpio_mask_irq;
+ g->irq.irq_unmask = my_gpio_unmask_irq;
+ g->irq.irq_set_type = my_gpio_set_irq_type;
+
+ /* Get a pointer to the gpio_irq_chip */
+ girq = &g->gc.irq;
+ girq->chip = &g->irq;
+ girq->default_type = IRQ_TYPE_NONE;
+ girq->handler = handle_bad_irq;
+ girq->fwnode = g->fwnode;
+ girq->parent_domain = parent;
+ girq->child_to_parent_hwirq = my_gpio_child_to_parent_hwirq;
+
+ return devm_gpiochip_add_data(dev, &g->gc, g);
+
+As you can see pretty similar, but you do not supply a parent handler for
+the IRQ, instead a parent irqdomain, an fwnode for the hardware and
+a funcion .child_to_parent_hwirq() that has the purpose of looking up
+the parent hardware irq from a child (i.e. this gpio chip) hardware irq.
+As always it is good to look at examples in the kernel tree for advice
+on how to find the required pieces.
+
+The old way of adding irqchips to gpiochips after registration is also still
+available but we try to move away from this:
+
+- DEPRECATED: gpiochip_irqchip_add(): adds a chained cascaded irqchip to a
+ gpiochip. It will pass the struct gpio_chip* for the chip to all IRQ
+ callbacks, so the callbacks need to embed the gpio_chip in its state
+ container and obtain a pointer to the container using container_of().
+ (See Documentation/driver-api/driver-model/design-patterns.rst)
+
+- gpiochip_irqchip_add_nested(): adds a nested cascaded irqchip to a gpiochip,
+ as discussed above regarding different types of cascaded irqchips. The
+ cascaded irq has to be handled by a threaded interrupt handler.
+ Apart from that it works exactly like the chained irqchip.
+
+- gpiochip_set_nested_irqchip(): sets up a nested cascaded irq handler for a
+ gpio_chip from a parent IRQ. As the parent IRQ has usually been
+ explicitly requested by the driver, this does very little more than
+ mark all the child IRQs as having the other IRQ as parent.
+
+If there is a need to exclude certain GPIO lines from the IRQ domain handled by
+these helpers, we can set .irq.need_valid_mask of the gpiochip before
+devm_gpiochip_add_data() or gpiochip_add_data() is called. This allocates an
+.irq.valid_mask with as many bits set as there are GPIO lines in the chip, each
+bit representing line 0..n-1. Drivers can exclude GPIO lines by clearing bits
+from this mask. The mask must be filled in before gpiochip_irqchip_add() or
+gpiochip_irqchip_add_nested() is called.
+
+To use the helpers please keep the following in mind:
+
+- Make sure to assign all relevant members of the struct gpio_chip so that
+ the irqchip can initialize. E.g. .dev and .can_sleep shall be set up
+ properly.
+
+- Nominally set all handlers to handle_bad_irq() in the setup call and pass
+ handle_bad_irq() as flow handler parameter in gpiochip_irqchip_add() if it is
+ expected for GPIO driver that irqchip .set_type() callback will be called
+ before using/enabling each GPIO IRQ. Then set the handler to
+ handle_level_irq() and/or handle_edge_irq() in the irqchip .set_type()
+ callback depending on what your controller supports and what is requested
+ by the consumer.
+
+
+Locking IRQ usage
+-----------------
+
+Since GPIO and irq_chip are orthogonal, we can get conflicts between different
+use cases. For example a GPIO line used for IRQs should be an input line,
+it does not make sense to fire interrupts on an output GPIO.
+
+If there is competition inside the subsystem which side is using the
+resource (a certain GPIO line and register for example) it needs to deny
+certain operations and keep track of usage inside of the gpiolib subsystem.
+
+Input GPIOs can be used as IRQ signals. When this happens, a driver is requested
+to mark the GPIO as being used as an IRQ::
+
+ int gpiochip_lock_as_irq(struct gpio_chip *chip, unsigned int offset)
+
+This will prevent the use of non-irq related GPIO APIs until the GPIO IRQ lock
+is released::
+
+ void gpiochip_unlock_as_irq(struct gpio_chip *chip, unsigned int offset)
+
+When implementing an irqchip inside a GPIO driver, these two functions should
+typically be called in the .startup() and .shutdown() callbacks from the
+irqchip.
+
+When using the gpiolib irqchip helpers, these callbacks are automatically
+assigned.
+
+
+Disabling and enabling IRQs
+---------------------------
+
+In some (fringe) use cases, a driver may be using a GPIO line as input for IRQs,
+but occasionally switch that line over to drive output and then back to being
+an input with interrupts again. This happens on things like CEC (Consumer
+Electronics Control).
+
+When a GPIO is used as an IRQ signal, then gpiolib also needs to know if
+the IRQ is enabled or disabled. In order to inform gpiolib about this,
+the irqchip driver should call::
+
+ void gpiochip_disable_irq(struct gpio_chip *chip, unsigned int offset)
+
+This allows drivers to drive the GPIO as an output while the IRQ is
+disabled. When the IRQ is enabled again, a driver should call::
+
+ void gpiochip_enable_irq(struct gpio_chip *chip, unsigned int offset)
+
+When implementing an irqchip inside a GPIO driver, these two functions should
+typically be called in the .irq_disable() and .irq_enable() callbacks from the
+irqchip.
+
+When using the gpiolib irqchip helpers, these callbacks are automatically
+assigned.
+
+
+Real-Time compliance for GPIO IRQ chips
+---------------------------------------
+
+Any provider of irqchips needs to be carefully tailored to support Real-Time
+preemption. It is desirable that all irqchips in the GPIO subsystem keep this
+in mind and do the proper testing to assure they are real time-enabled.
+
+So, pay attention on above realtime considerations in the documentation.
+
+The following is a checklist to follow when preparing a driver for real-time
+compliance:
+
+- ensure spinlock_t is not used as part irq_chip implementation
+- ensure that sleepable APIs are not used as part irq_chip implementation
+ If sleepable APIs have to be used, these can be done from the .irq_bus_lock()
+ and .irq_bus_unlock() callbacks
+- Chained GPIO irqchips: ensure spinlock_t or any sleepable APIs are not used
+ from the chained IRQ handler
+- Generic chained GPIO irqchips: take care about generic_handle_irq() calls and
+ apply corresponding work-around
+- Chained GPIO irqchips: get rid of the chained IRQ handler and use generic irq
+ handler if possible
+- regmap_mmio: it is possible to disable internal locking in regmap by setting
+ .disable_locking and handling the locking in the GPIO driver
+- Test your driver with the appropriate in-kernel real-time test cases for both
+ level and edge IRQs
+
+* [1] http://www.spinics.net/lists/linux-omap/msg120425.html
+* [2] https://lkml.org/lkml/2015/9/25/494
+* [3] https://lkml.org/lkml/2015/9/25/495
+
+
+Requesting self-owned GPIO pins
+===============================
+
+Sometimes it is useful to allow a GPIO chip driver to request its own GPIO
+descriptors through the gpiolib API. A GPIO driver can use the following
+functions to request and free descriptors::
+
+ struct gpio_desc *gpiochip_request_own_desc(struct gpio_desc *desc,
+ u16 hwnum,
+ const char *label,
+ enum gpiod_flags flags)
+
+ void gpiochip_free_own_desc(struct gpio_desc *desc)
+
+Descriptors requested with gpiochip_request_own_desc() must be released with
+gpiochip_free_own_desc().
+
+These functions must be used with care since they do not affect module use
+count. Do not use the functions to request gpio descriptors not owned by the
+calling driver.