summaryrefslogtreecommitdiffstats
path: root/Documentation/driver-api/media/csi2.rst
diff options
context:
space:
mode:
Diffstat (limited to '')
-rw-r--r--Documentation/driver-api/media/csi2.rst93
1 files changed, 93 insertions, 0 deletions
diff --git a/Documentation/driver-api/media/csi2.rst b/Documentation/driver-api/media/csi2.rst
new file mode 100644
index 000000000..e1b838014
--- /dev/null
+++ b/Documentation/driver-api/media/csi2.rst
@@ -0,0 +1,93 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+.. _MIPI_CSI_2:
+
+MIPI CSI-2
+==========
+
+CSI-2 is a data bus intended for transferring images from cameras to
+the host SoC. It is defined by the `MIPI alliance`_.
+
+.. _`MIPI alliance`: http://www.mipi.org/
+
+Media bus formats
+-----------------
+
+See :ref:`v4l2-mbus-pixelcode` for details on which media bus formats should
+be used for CSI-2 interfaces.
+
+Transmitter drivers
+-------------------
+
+CSI-2 transmitter, such as a sensor or a TV tuner, drivers need to
+provide the CSI-2 receiver with information on the CSI-2 bus
+configuration. These include the V4L2_CID_LINK_FREQ and
+V4L2_CID_PIXEL_RATE controls and
+(:c:type:`v4l2_subdev_video_ops`->s_stream() callback). These
+interface elements must be present on the sub-device represents the
+CSI-2 transmitter.
+
+The V4L2_CID_LINK_FREQ control is used to tell the receiver driver the
+frequency (and not the symbol rate) of the link. The
+V4L2_CID_PIXEL_RATE is may be used by the receiver to obtain the pixel
+rate the transmitter uses. The
+:c:type:`v4l2_subdev_video_ops`->s_stream() callback provides an
+ability to start and stop the stream.
+
+The value of the V4L2_CID_PIXEL_RATE is calculated as follows::
+
+ pixel_rate = link_freq * 2 * nr_of_lanes / bits_per_sample
+
+where
+
+.. list-table:: variables in pixel rate calculation
+ :header-rows: 1
+
+ * - variable or constant
+ - description
+ * - link_freq
+ - The value of the V4L2_CID_LINK_FREQ integer64 menu item.
+ * - nr_of_lanes
+ - Number of data lanes used on the CSI-2 link. This can
+ be obtained from the OF endpoint configuration.
+ * - 2
+ - Two bits are transferred per clock cycle per lane.
+ * - bits_per_sample
+ - Number of bits per sample.
+
+The transmitter drivers must, if possible, configure the CSI-2
+transmitter to *LP-11 mode* whenever the transmitter is powered on but
+not active, and maintain *LP-11 mode* until stream on. Only at stream
+on should the transmitter activate the clock on the clock lane and
+transition to *HS mode*.
+
+Some transmitters do this automatically but some have to be explicitly
+programmed to do so, and some are unable to do so altogether due to
+hardware constraints.
+
+Stopping the transmitter
+^^^^^^^^^^^^^^^^^^^^^^^^
+
+A transmitter stops sending the stream of images as a result of
+calling the ``.s_stream()`` callback. Some transmitters may stop the
+stream at a frame boundary whereas others stop immediately,
+effectively leaving the current frame unfinished. The receiver driver
+should not make assumptions either way, but function properly in both
+cases.
+
+Receiver drivers
+----------------
+
+Before the receiver driver may enable the CSI-2 transmitter by using
+the :c:type:`v4l2_subdev_video_ops`->s_stream(), it must have powered
+the transmitter up by using the
+:c:type:`v4l2_subdev_core_ops`->s_power() callback. This may take
+place either indirectly by using :c:func:`v4l2_pipeline_pm_get` or
+directly.
+
+Formats
+-------
+
+The media bus pixel codes document parallel formats. Should the pixel data be
+transported over a serial bus, the media bus pixel code that describes a
+parallel format that transfers a sample on a single clock cycle is used.