summaryrefslogtreecommitdiffstats
path: root/Documentation/powerpc/booting.rst
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/powerpc/booting.rst')
-rw-r--r--Documentation/powerpc/booting.rst110
1 files changed, 110 insertions, 0 deletions
diff --git a/Documentation/powerpc/booting.rst b/Documentation/powerpc/booting.rst
new file mode 100644
index 000000000..2d0ec2ff2
--- /dev/null
+++ b/Documentation/powerpc/booting.rst
@@ -0,0 +1,110 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+DeviceTree Booting
+------------------
+
+During the development of the Linux/ppc64 kernel, and more specifically, the
+addition of new platform types outside of the old IBM pSeries/iSeries pair, it
+was decided to enforce some strict rules regarding the kernel entry and
+bootloader <-> kernel interfaces, in order to avoid the degeneration that had
+become the ppc32 kernel entry point and the way a new platform should be added
+to the kernel. The legacy iSeries platform breaks those rules as it predates
+this scheme, but no new board support will be accepted in the main tree that
+doesn't follow them properly. In addition, since the advent of the arch/powerpc
+merged architecture for ppc32 and ppc64, new 32-bit platforms and 32-bit
+platforms which move into arch/powerpc will be required to use these rules as
+well.
+
+The main requirement that will be defined in more detail below is the presence
+of a device-tree whose format is defined after Open Firmware specification.
+However, in order to make life easier to embedded board vendors, the kernel
+doesn't require the device-tree to represent every device in the system and only
+requires some nodes and properties to be present. For example, the kernel does
+not require you to create a node for every PCI device in the system. It is a
+requirement to have a node for PCI host bridges in order to provide interrupt
+routing information and memory/IO ranges, among others. It is also recommended
+to define nodes for on chip devices and other buses that don't specifically fit
+in an existing OF specification. This creates a great flexibility in the way the
+kernel can then probe those and match drivers to device, without having to hard
+code all sorts of tables. It also makes it more flexible for board vendors to do
+minor hardware upgrades without significantly impacting the kernel code or
+cluttering it with special cases.
+
+
+Entry point
+~~~~~~~~~~~
+
+There is one single entry point to the kernel, at the start
+of the kernel image. That entry point supports two calling
+conventions:
+
+ a) Boot from Open Firmware. If your firmware is compatible
+ with Open Firmware (IEEE 1275) or provides an OF compatible
+ client interface API (support for "interpret" callback of
+ forth words isn't required), you can enter the kernel with:
+
+ r5 : OF callback pointer as defined by IEEE 1275
+ bindings to powerpc. Only the 32-bit client interface
+ is currently supported
+
+ r3, r4 : address & length of an initrd if any or 0
+
+ The MMU is either on or off; the kernel will run the
+ trampoline located in arch/powerpc/kernel/prom_init.c to
+ extract the device-tree and other information from open
+ firmware and build a flattened device-tree as described
+ in b). prom_init() will then re-enter the kernel using
+ the second method. This trampoline code runs in the
+ context of the firmware, which is supposed to handle all
+ exceptions during that time.
+
+ b) Direct entry with a flattened device-tree block. This entry
+ point is called by a) after the OF trampoline and can also be
+ called directly by a bootloader that does not support the Open
+ Firmware client interface. It is also used by "kexec" to
+ implement "hot" booting of a new kernel from a previous
+ running one. This method is what I will describe in more
+ details in this document, as method a) is simply standard Open
+ Firmware, and thus should be implemented according to the
+ various standard documents defining it and its binding to the
+ PowerPC platform. The entry point definition then becomes:
+
+ r3 : physical pointer to the device-tree block
+ (defined in chapter II) in RAM
+
+ r4 : physical pointer to the kernel itself. This is
+ used by the assembly code to properly disable the MMU
+ in case you are entering the kernel with MMU enabled
+ and a non-1:1 mapping.
+
+ r5 : NULL (as to differentiate with method a)
+
+Note about SMP entry: Either your firmware puts your other
+CPUs in some sleep loop or spin loop in ROM where you can get
+them out via a soft reset or some other means, in which case
+you don't need to care, or you'll have to enter the kernel
+with all CPUs. The way to do that with method b) will be
+described in a later revision of this document.
+
+Board supports (platforms) are not exclusive config options. An
+arbitrary set of board supports can be built in a single kernel
+image. The kernel will "know" what set of functions to use for a
+given platform based on the content of the device-tree. Thus, you
+should:
+
+ a) add your platform support as a _boolean_ option in
+ arch/powerpc/Kconfig, following the example of PPC_PSERIES,
+ PPC_PMAC and PPC_MAPLE. The later is probably a good
+ example of a board support to start from.
+
+ b) create your main platform file as
+ "arch/powerpc/platforms/myplatform/myboard_setup.c" and add it
+ to the Makefile under the condition of your ``CONFIG_``
+ option. This file will define a structure of type "ppc_md"
+ containing the various callbacks that the generic code will
+ use to get to your platform specific code
+
+A kernel image may support multiple platforms, but only if the
+platforms feature the same core architecture. A single kernel build
+cannot support both configurations with Book E and configurations
+with classic Powerpc architectures.