diff options
Diffstat (limited to 'arch/arm/boot/dts/gemini-dlink-dir-685.dts')
| -rw-r--r-- | arch/arm/boot/dts/gemini-dlink-dir-685.dts | 511 |
1 files changed, 511 insertions, 0 deletions
diff --git a/arch/arm/boot/dts/gemini-dlink-dir-685.dts b/arch/arm/boot/dts/gemini-dlink-dir-685.dts new file mode 100644 index 000000000..cc39289e9 --- /dev/null +++ b/arch/arm/boot/dts/gemini-dlink-dir-685.dts @@ -0,0 +1,511 @@ +/* + * Device Tree file for D-Link DIR-685 Xtreme N Storage Router + */ + +/dts-v1/; + +#include "gemini.dtsi" +#include <dt-bindings/input/input.h> + +/ { + model = "D-Link DIR-685 Xtreme N Storage Router"; + compatible = "dlink,dir-685", "cortina,gemini"; + #address-cells = <1>; + #size-cells = <1>; + + memory@0 { + /* 128 MB SDRAM in 2 x Hynix HY5DU121622DTP-D43 */ + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,19200n8 root=/dev/sda1 rw rootwait consoleblank=300"; + stdout-path = "uart0:19200n8"; + }; + + gpio_keys { + compatible = "gpio-keys"; + + button-esc { + debounce-interval = <100>; + wakeup-source; + linux,code = <KEY_ESC>; + label = "reset"; + /* Collides with LPC_LAD[0], UART DCD, SSP 97RST */ + gpios = <&gpio0 8 GPIO_ACTIVE_LOW>; + }; + button-eject { + debounce-interval = <100>; + wakeup-source; + linux,code = <KEY_EJECTCD>; + label = "unmount"; + /* Collides with LPC LFRAME, UART RTS, SSP TXD */ + gpios = <&gpio0 13 GPIO_ACTIVE_LOW>; + }; + }; + + vdisp: regulator { + compatible = "regulator-fixed"; + regulator-name = "display-power"; + regulator-min-microvolt = <3600000>; + regulator-max-microvolt = <3600000>; + /* Collides with LCD E */ + gpio = <&gpio0 16 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + spi { + compatible = "spi-gpio"; + #address-cells = <1>; + #size-cells = <0>; + + /* Collides with IDE pins, that's cool (we do not use them) */ + gpio-sck = <&gpio1 5 GPIO_ACTIVE_HIGH>; + gpio-miso = <&gpio1 8 GPIO_ACTIVE_HIGH>; + gpio-mosi = <&gpio1 7 GPIO_ACTIVE_HIGH>; + cs-gpios = <&gpio0 20 GPIO_ACTIVE_LOW>; + num-chipselects = <1>; + + panel: display@0 { + compatible = "dlink,dir-685-panel", "ilitek,ili9322"; + reg = <0>; + /* 50 ns min period = 20 MHz */ + spi-max-frequency = <20000000>; + vcc-supply = <&vdisp>; + iovcc-supply = <&vdisp>; + vci-supply = <&vdisp>; + + port { + panel_in: endpoint { + remote-endpoint = <&display_out>; + }; + }; + }; + }; + + leds { + compatible = "gpio-leds"; + led-wps { + label = "dir685:blue:WPS"; + /* Collides with ICE */ + gpios = <&gpio0 7 GPIO_ACTIVE_LOW>; + default-state = "on"; + linux,default-trigger = "heartbeat"; + }; + /* + * These two LEDs are on the side of the device. + * For electrical reasons, both LEDs cannot be active + * at the same time so only blue or orange can be on at + * one time. Enabling both makes the LED go dark. + * The LEDs both sit inside the unmount button and the + * label on the case says "unmount". + */ + led-blue-hd { + label = "dir685:blue:HD"; + /* Collides with LPC_SERIRQ, UART DTR, SSP FSC pins */ + gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>; + default-state = "off"; + linux,default-trigger = "disk-read"; + }; + led-orange-hd { + label = "dir685:orange:HD"; + /* Collides with LPC_LAD[2], UART DSR, SSP ECLK pins */ + gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; + default-state = "off"; + linux,default-trigger = "disk-write"; + }; + }; + + /* + * This is a Sunon Maglev GM0502PFV2-8 cooling fan @10000 RPM. + * sensor. It is turned on when the temperature exceeds 46 degrees + * and turned off when the temperatures goes below 41 degrees + * (celsius). + */ + fan0: gpio-fan { + compatible = "gpio-fan"; + /* Collides with IDE */ + gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>; + gpio-fan,speed-map = <0 0>, <10000 1>; + #cooling-cells = <2>; + }; + + thermal-zones { + chassis-thermal { + /* Poll every 20 seconds */ + polling-delay = <20000>; + /* Poll every 2nd second when cooling */ + polling-delay-passive = <2000>; + /* Use the thermal sensor in the hard drive */ + thermal-sensors = <&drive0>; + + /* Tripping points from the fan.script in the rootfs */ + trips { + alert: chassis-alert { + /* At 43 degrees turn on the fan */ + temperature = <43000>; + hysteresis = <3000>; + type = "active"; + }; + crit: chassis-crit { + /* Just shut down at 60 degrees */ + temperature = <60000>; + hysteresis = <2000>; + type = "critical"; + }; + }; + + cooling-maps { + map0 { + trip = <&alert>; + cooling-device = <&fan0 1 1>; + }; + }; + }; + }; + + /* + * The touchpad input is connected to a GPIO bit-banged + * I2C bus. + */ + gpio-i2c { + compatible = "i2c-gpio"; + /* Collides with ICE */ + sda-gpios = <&gpio0 5 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio0 6 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + #address-cells = <1>; + #size-cells = <0>; + + touchkeys@26 { + compatible = "dlink,dir685-touchkeys"; + reg = <0x26>; + interrupt-parent = <&gpio0>; + /* Collides with NAND flash */ + interrupts = <17 IRQ_TYPE_EDGE_FALLING>; + }; + }; + + /* This is a RealTek RTL8366RB switch and PHY using SMI over GPIO */ + switch { + compatible = "realtek,rtl8366rb"; + /* 22 = MDIO (has input reads), 21 = MDC (clock, output only) */ + mdc-gpios = <&gpio0 21 GPIO_ACTIVE_HIGH>; + mdio-gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio0 14 GPIO_ACTIVE_LOW>; + realtek,disable-leds; + + switch_intc: interrupt-controller { + /* GPIO 15 provides the interrupt */ + interrupt-parent = <&gpio0>; + interrupts = <15 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan0"; + phy-handle = <&phy0>; + }; + port@1 { + reg = <1>; + label = "lan1"; + phy-handle = <&phy1>; + }; + port@2 { + reg = <2>; + label = "lan2"; + phy-handle = <&phy2>; + }; + port@3 { + reg = <3>; + label = "lan3"; + phy-handle = <&phy3>; + }; + port@4 { + reg = <4>; + label = "wan"; + phy-handle = <&phy4>; + }; + rtl8366rb_cpu_port: port@5 { + reg = <5>; + label = "cpu"; + ethernet = <&gmac0>; + phy-mode = "rgmii"; + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + + }; + + mdio { + compatible = "realtek,smi-mdio"; + #address-cells = <1>; + #size-cells = <0>; + + phy0: phy@0 { + reg = <0>; + interrupt-parent = <&switch_intc>; + interrupts = <0>; + }; + phy1: phy@1 { + reg = <1>; + interrupt-parent = <&switch_intc>; + interrupts = <1>; + }; + phy2: phy@2 { + reg = <2>; + interrupt-parent = <&switch_intc>; + interrupts = <2>; + }; + phy3: phy@3 { + reg = <3>; + interrupt-parent = <&switch_intc>; + interrupts = <3>; + }; + phy4: phy@4 { + reg = <4>; + interrupt-parent = <&switch_intc>; + interrupts = <12>; + }; + }; + }; + + soc { + flash@30000000 { + /* + * Flash access collides with the Chip Enable signal for + * the display panel, that reuse the parallel flash Chip + * Select 1 (CS1). We switch the pin control state so we + * enable these pins for flash access only when we need + * then, and when disabled they can be used for GPIO which + * is what the display panel needs. + */ + status = "okay"; + pinctrl-names = "enabled", "disabled"; + pinctrl-0 = <&pflash_default_pins>; + pinctrl-1 = <&pflash_disabled_pins>; + + /* 32MB of flash */ + reg = <0x30000000 0x02000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + /* + * This "RedBoot" is the Storlink derivative. + */ + partition@0 { + label = "RedBoot"; + reg = <0x00000000 0x00040000>; + read-only; + }; + /* + * This firmware image contains the kernel catenated + * with the squashfs root filesystem. For some reason + * this is called "upgrade" on the vendor system. + */ + partition@40000 { + label = "upgrade"; + reg = <0x00040000 0x01f40000>; + read-only; + }; + /* RGDB, Residental Gateway Database? */ + partition@1f80000 { + label = "rgdb"; + reg = <0x01f80000 0x00040000>; + read-only; + }; + /* + * This partition contains MAC addresses for WAN, + * WLAN and LAN, and the country code (for wireless + * I guess). + */ + partition@1fc0000 { + label = "nvram"; + reg = <0x01fc0000 0x00020000>; + read-only; + }; + partition@1fe0000 { + label = "LangPack"; + reg = <0x01fe0000 0x00020000>; + read-only; + }; + }; + }; + + syscon: syscon@40000000 { + pinctrl { + /* + * gpio0bgrp cover line 5, 6 used by TK I2C + * gpio0bgrp cover line 7 used by WPS LED + * gpio0cgrp cover line 8, 13 used by keys + * and 11, 12 used by the HD LEDs + * and line 14, 15 used by RTL8366 + * RESET and phy ready + * gpio0egrp cover line 16 used by VDISP + * gpio0fgrp cover line 17 used by TK IRQ + * gpio0ggrp cover line 20 used by panel CS + * gpio0hgrp cover line 21,22 used by RTL8366RB MDIO + */ + gpio0_default_pins: pinctrl-gpio0 { + mux { + function = "gpio0"; + groups = "gpio0bgrp", + "gpio0cgrp", + "gpio0egrp", + "gpio0fgrp", + "gpio0hgrp"; + }; + }; + /* + * gpio1bgrp cover line 5,8,7 used by panel SPI + * also line 6 used by the fan + * + */ + gpio1_default_pins: pinctrl-gpio1 { + mux { + function = "gpio1"; + groups = "gpio1bgrp"; + }; + }; + /* + * These GPIO groups will be mapped in over some + * of the flash pins when the flash is not in + * active use. + */ + pflash_disabled_pins: pinctrl-pflash-disabled { + mux { + function = "gpio0"; + groups = "gpio0ggrp", "gpio0igrp", "gpio0jgrp", + "gpio0kgrp"; + }; + }; + pinctrl-gmii { + mux { + function = "gmii"; + groups = "gmii_gmac0_grp"; + }; + conf0 { + pins = "V8 GMAC0 RXDV", "T10 GMAC1 RXDV", + "Y7 GMAC0 RXC", "Y11 GMAC1 RXC", + "T8 GMAC0 TXEN", "W11 GMAC1 TXEN", + "U8 GMAC0 TXC", "V11 GMAC1 TXC", + "W8 GMAC0 RXD0", "V9 GMAC0 RXD1", + "Y8 GMAC0 RXD2", "U9 GMAC0 RXD3", + "T7 GMAC0 TXD0", "U6 GMAC0 TXD1", + "V7 GMAC0 TXD2", "U7 GMAC0 TXD3", + "Y12 GMAC1 RXD0", "V12 GMAC1 RXD1", + "T11 GMAC1 RXD2", "W12 GMAC1 RXD3", + "U10 GMAC1 TXD0", "Y10 GMAC1 TXD1", + "W10 GMAC1 TXD2", "T9 GMAC1 TXD3"; + skew-delay = <7>; + }; + /* Set up drive strength on GMAC0 to 16 mA */ + conf1 { + groups = "gmii_gmac0_grp"; + drive-strength = <16>; + }; + }; + }; + }; + + sata: sata@46000000 { + cortina,gemini-ata-muxmode = <0>; + cortina,gemini-enable-sata-bridge; + status = "okay"; + }; + + gpio0: gpio@4d000000 { + pinctrl-names = "default"; + pinctrl-0 = <&gpio0_default_pins>; + }; + + gpio1: gpio@4e000000 { + pinctrl-names = "default"; + pinctrl-0 = <&gpio1_default_pins>; + }; + + pci@50000000 { + status = "okay"; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = + <0x4800 0 0 1 &pci_intc 0>, /* Slot 9 */ + <0x4800 0 0 2 &pci_intc 1>, + <0x4800 0 0 3 &pci_intc 2>, + <0x4800 0 0 4 &pci_intc 3>, + <0x5000 0 0 1 &pci_intc 1>, /* Slot 10 */ + <0x5000 0 0 2 &pci_intc 2>, + <0x5000 0 0 3 &pci_intc 3>, + <0x5000 0 0 4 &pci_intc 0>, + <0x5800 0 0 1 &pci_intc 2>, /* Slot 11 */ + <0x5800 0 0 2 &pci_intc 3>, + <0x5800 0 0 3 &pci_intc 0>, + <0x5800 0 0 4 &pci_intc 1>, + <0x6000 0 0 1 &pci_intc 3>, /* Slot 12 */ + <0x6000 0 0 2 &pci_intc 0>, + <0x6000 0 0 3 &pci_intc 1>, + <0x6000 0 0 4 &pci_intc 2>; + }; + + ethernet@60000000 { + status = "okay"; + + ethernet-port@0 { + phy-mode = "rgmii"; + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + ethernet-port@1 { + /* Not used in this platform */ + }; + }; + + ide@63000000 { + status = "okay"; + + /* + * This drive may have a temperature sensor with a + * thermal zone we can use for thermal control of the + * chassis temperature using the fan. + */ + drive0: ide-port@0 { + reg = <0>; + #thermal-sensor-cells = <0>; + }; + }; + + display-controller@6a000000 { + status = "okay"; + + port@0 { + reg = <0>; + display_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; + }; + + usb@68000000 { + status = "okay"; + }; + + usb@69000000 { + status = "okay"; + }; + }; +}; |