diff options
Diffstat (limited to 'arch/arm/boot/dts/imx6sx-softing-vining-2000.dts')
| -rw-r--r-- | arch/arm/boot/dts/imx6sx-softing-vining-2000.dts | 587 |
1 files changed, 587 insertions, 0 deletions
diff --git a/arch/arm/boot/dts/imx6sx-softing-vining-2000.dts b/arch/arm/boot/dts/imx6sx-softing-vining-2000.dts new file mode 100644 index 000000000..554791687 --- /dev/null +++ b/arch/arm/boot/dts/imx6sx-softing-vining-2000.dts @@ -0,0 +1,587 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Copyright (C) 2016 Christoph Fritz <chf.fritz@googlemail.com> + */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include "imx6sx.dtsi" + +/ { + model = "Softing VIN|ING 2000"; + compatible = "samtec,imx6sx-vining-2000", "fsl,imx6sx"; + + chosen { + stdout-path = &uart1; + }; + + memory@80000000 { + device_type = "memory"; + reg = <0x80000000 0x40000000>; + }; + + reg_usb_otg1_vbus: regulator-usb_otg1_vbus { + compatible = "regulator-fixed"; + regulator-name = "usb_otg1_vbus"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb_otg1>; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio1 9 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_peri_3v3: regulator-peri_3v3 { + compatible = "regulator-fixed"; + regulator-name = "peri_3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + pwmleds { + compatible = "pwm-leds"; + + red { + label = "red"; + max-brightness = <255>; + pwms = <&pwm6 0 50000>; + }; + + green { + label = "green"; + max-brightness = <255>; + pwms = <&pwm2 0 50000>; + }; + + blue { + label = "blue"; + max-brightness = <255>; + pwms = <&pwm1 0 50000>; + }; + }; +}; + +&adc1 { + vref-supply = <®_peri_3v3>; + status = "okay"; +}; + +&cpu0 { + /* + * This board has a shared rail of reg_arm and reg_soc (supplied by + * sw1a_reg) which is modeled below, but still this module behaves + * unstable without higher voltages. Hence, set higher voltages here. + */ + operating-points = < + /* kHz uV */ + 996000 1250000 + 792000 1175000 + 396000 1175000 + 198000 1175000 + >; + fsl,soc-operating-points = < + /* ARM kHz SOC uV */ + 996000 1250000 + 792000 1175000 + 396000 1175000 + 198000 1175000 + >; +}; + +&ecspi4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi4>; + cs-gpios = <&gpio7 4 GPIO_ACTIVE_LOW>; + status = "okay"; +}; + +&fec1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet1>; + phy-supply = <®_peri_3v3>; + phy-reset-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>; + phy-reset-duration = <5>; + phy-mode = "rmii"; + phy-handle = <ðphy0>; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy0: ethernet0-phy@0 { + reg = <0>; + max-speed = <100>; + interrupt-parent = <&gpio2>; + interrupts = <17 IRQ_TYPE_LEVEL_LOW>; + }; + }; +}; + +&fec2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet2>; + phy-supply = <®_peri_3v3>; + phy-reset-gpios = <&gpio5 21 GPIO_ACTIVE_LOW>; + phy-reset-duration = <5>; + phy-mode = "rmii"; + phy-handle = <ðphy1>; + status = "okay"; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + + ethphy1: ethernet1-phy@0 { + reg = <0>; + max-speed = <100>; + interrupt-parent = <&gpio2>; + interrupts = <19 IRQ_TYPE_LEVEL_LOW>; + }; + }; +}; + +&flexcan1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexcan1>; + status = "okay"; +}; + +&flexcan2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexcan2>; + status = "okay"; +}; + +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + proximity: sx9500@28 { + compatible = "semtech,sx9500"; + reg = <0x28>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sx9500>; + interrupt-parent = <&gpio2>; + interrupts = <16 IRQ_TYPE_LEVEL_LOW>; + reset-gpios = <&gpio2 10 GPIO_ACTIVE_HIGH>; + }; + + pmic: pfuze100@8 { + compatible = "fsl,pfuze200"; + reg = <0x08>; + + regulators { + sw1a_reg: sw1ab { + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1875000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <6250>; + }; + + sw2_reg: sw2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3a_reg: sw3a { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1975000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3b_reg: sw3b { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1975000>; + regulator-boot-on; + regulator-always-on; + }; + + snvs_reg: vsnvs { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3000000>; + regulator-boot-on; + regulator-always-on; + }; + + vref_reg: vrefddr { + regulator-boot-on; + regulator-always-on; + }; + + vgen1_reg: vgen1 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + regulator-always-on; + }; + + vgen2_reg: vgen2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + }; + + vgen3_reg: vgen3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen4_reg: vgen4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen5_reg: vgen5 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen6_reg: vgen6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + }; + }; +}; + +&i2c3 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpios>; + + pinctrl_ecspi4: ecspi4grp { + fsl,pins = < + MX6SX_PAD_SD3_CLK__ECSPI4_SCLK 0x130b1 + MX6SX_PAD_SD3_DATA3__ECSPI4_MISO 0x130b1 + MX6SX_PAD_SD3_CMD__ECSPI4_MOSI 0x130b1 + MX6SX_PAD_SD3_DATA2__GPIO7_IO_4 0x30b0 + >; + }; + + pinctrl_enet1: enet1grp { + fsl,pins = < + MX6SX_PAD_RGMII1_RD0__ENET1_RX_DATA_0 0x30c1 + MX6SX_PAD_RGMII1_RD1__ENET1_RX_DATA_1 0x30c1 + MX6SX_PAD_RGMII1_TD0__ENET1_TX_DATA_0 0xa0f9 + MX6SX_PAD_RGMII1_TD1__ENET1_TX_DATA_1 0xa0f9 + MX6SX_PAD_RGMII1_RX_CTL__ENET1_RX_EN 0x30c1 + MX6SX_PAD_RGMII1_TX_CTL__ENET1_TX_EN 0xa0f9 + MX6SX_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x4000a038 + /* LAN8720 PHY Reset */ + MX6SX_PAD_RGMII1_TD3__GPIO5_IO_9 0x10b0 + /* MDIO */ + MX6SX_PAD_ENET1_MDC__ENET1_MDC 0xa0f9 + MX6SX_PAD_ENET1_MDIO__ENET1_MDIO 0xa0f9 + /* IRQ from PHY */ + MX6SX_PAD_KEY_ROW2__GPIO2_IO_17 0x10b0 + >; + }; + + pinctrl_enet2: enet2grp { + fsl,pins = < + MX6SX_PAD_RGMII2_TD0__ENET2_TX_DATA_0 0x1b0b0 + MX6SX_PAD_RGMII2_TD1__ENET2_TX_DATA_1 0x1b0b0 + MX6SX_PAD_RGMII2_RD0__ENET2_RX_DATA_0 0x1b0b0 + MX6SX_PAD_RGMII2_RD1__ENET2_RX_DATA_1 0x1b0b0 + MX6SX_PAD_RGMII2_RX_CTL__ENET2_RX_EN 0x1b0b0 + MX6SX_PAD_RGMII2_TX_CTL__ENET2_TX_EN 0x1b0b0 + MX6SX_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 0x4000a038 + /* LAN8720 PHY Reset */ + MX6SX_PAD_RGMII2_TD3__GPIO5_IO_21 0x10b0 + /* MDIO */ + MX6SX_PAD_ENET1_COL__ENET2_MDC 0xa0f9 + MX6SX_PAD_ENET1_CRS__ENET2_MDIO 0xa0f9 + /* IRQ from PHY */ + MX6SX_PAD_KEY_ROW4__GPIO2_IO_19 0x10b0 + >; + }; + + pinctrl_flexcan1: flexcan1grp { + fsl,pins = < + MX6SX_PAD_QSPI1B_DQS__CAN1_TX 0x1b0b0 + MX6SX_PAD_QSPI1A_SS1_B__CAN1_RX 0x1b0b0 + >; + }; + + pinctrl_flexcan2: flexcan2grp { + fsl,pins = < + MX6SX_PAD_QSPI1B_SS1_B__CAN2_RX 0x1b0b0 + MX6SX_PAD_QSPI1A_DQS__CAN2_TX 0x1b0b0 + >; + }; + + pinctrl_gpios: gpiosgrp { + fsl,pins = < + /* reset external uC */ + MX6SX_PAD_QSPI1A_DATA3__GPIO4_IO_19 0x10b0 + /* IRQ from external uC */ + MX6SX_PAD_KEY_ROW0__GPIO2_IO_15 0x10b0 + /* overcurrent detection */ + MX6SX_PAD_GPIO1_IO08__GPIO1_IO_8 0x10b0 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX6SX_PAD_GPIO1_IO01__I2C1_SDA 0x4001b8b1 + MX6SX_PAD_GPIO1_IO00__I2C1_SCL 0x4001b8b1 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX6SX_PAD_NAND_ALE__I2C3_SDA 0x4001b8b1 + MX6SX_PAD_NAND_CLE__I2C3_SCL 0x4001b8b1 + >; + }; + + pinctrl_pcie: pciegrp { + fsl,pins = < + MX6SX_PAD_NAND_DATA02__GPIO4_IO_6 0x10b0 + >; + }; + + pinctrl_pwm1: pwm1grp-1 { + fsl,pins = < + /* blue LED */ + MX6SX_PAD_RGMII2_RD3__PWM1_OUT 0x1b0b1 + >; + }; + + pinctrl_pwm2: pwm2grp-1 { + fsl,pins = < + /* green LED */ + MX6SX_PAD_RGMII2_RD2__PWM2_OUT 0x1b0b1 + >; + }; + + pinctrl_pwm6: pwm6grp-1 { + fsl,pins = < + /* red LED */ + MX6SX_PAD_RGMII2_TD2__PWM6_OUT 0x1b0b1 + >; + }; + + pinctrl_sx9500: sx9500grp { + fsl,pins = < + /* Reset */ + MX6SX_PAD_KEY_COL0__GPIO2_IO_10 0x838 + /* IRQ */ + MX6SX_PAD_KEY_ROW1__GPIO2_IO_16 0x70e0 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX6SX_PAD_GPIO1_IO04__UART1_DCE_TX 0x1b0b1 + MX6SX_PAD_GPIO1_IO05__UART1_DCE_RX 0x1b0b1 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX6SX_PAD_GPIO1_IO06__UART2_DCE_TX 0x1b0b1 + MX6SX_PAD_GPIO1_IO07__UART2_DCE_RX 0x1b0b1 + >; + }; + + pinctrl_usb_otg1: usbotg1grp { + fsl,pins = < + MX6SX_PAD_GPIO1_IO09__GPIO1_IO_9 0x10b0 + >; + }; + + pinctrl_usb_otg1_id: usbotg1idgrp { + fsl,pins = < + MX6SX_PAD_GPIO1_IO10__ANATOP_OTG1_ID 0x17059 + >; + }; + + pinctrl_usdhc2_50mhz: usdhc2grp-50mhz { + fsl,pins = < + MX6SX_PAD_SD2_CLK__USDHC2_CLK 0x10059 + MX6SX_PAD_SD2_CMD__USDHC2_CMD 0x17059 + MX6SX_PAD_SD2_DATA0__USDHC2_DATA0 0x17059 + MX6SX_PAD_SD2_DATA1__USDHC2_DATA1 0x17059 + MX6SX_PAD_SD2_DATA2__USDHC2_DATA2 0x17059 + MX6SX_PAD_SD2_DATA3__USDHC2_DATA3 0x17059 + MX6SX_PAD_LCD1_VSYNC__GPIO3_IO_28 0x1b000 + MX6SX_PAD_LCD1_HSYNC__GPIO3_IO_26 0x10b0 + >; + }; + + pinctrl_usdhc2_100mhz: usdhc2grp-100mhz { + fsl,pins = < + MX6SX_PAD_SD2_CLK__USDHC2_CLK 0x100b9 + MX6SX_PAD_SD2_CMD__USDHC2_CMD 0x170b9 + MX6SX_PAD_SD2_DATA0__USDHC2_DATA0 0x170b9 + MX6SX_PAD_SD2_DATA1__USDHC2_DATA1 0x170b9 + MX6SX_PAD_SD2_DATA2__USDHC2_DATA2 0x170b9 + MX6SX_PAD_SD2_DATA3__USDHC2_DATA3 0x170b9 + >; + }; + + pinctrl_usdhc2_200mhz: usdhc2grp-200mhz { + fsl,pins = < + MX6SX_PAD_SD2_CLK__USDHC2_CLK 0x100f9 + MX6SX_PAD_SD2_CMD__USDHC2_CMD 0x170f9 + MX6SX_PAD_SD2_DATA0__USDHC2_DATA0 0x170f9 + MX6SX_PAD_SD2_DATA1__USDHC2_DATA1 0x170f9 + MX6SX_PAD_SD2_DATA2__USDHC2_DATA2 0x170f9 + MX6SX_PAD_SD2_DATA3__USDHC2_DATA3 0x170f9 + >; + }; + + pinctrl_usdhc4_50mhz: usdhc4grp-50mhz { + fsl,pins = < + MX6SX_PAD_SD4_CLK__USDHC4_CLK 0x10059 + MX6SX_PAD_SD4_CMD__USDHC4_CMD 0x17059 + MX6SX_PAD_SD4_DATA0__USDHC4_DATA0 0x17059 + MX6SX_PAD_SD4_DATA1__USDHC4_DATA1 0x17059 + MX6SX_PAD_SD4_DATA2__USDHC4_DATA2 0x17059 + MX6SX_PAD_SD4_DATA3__USDHC4_DATA3 0x17059 + MX6SX_PAD_SD4_DATA4__USDHC4_DATA4 0x17059 + MX6SX_PAD_SD4_DATA5__USDHC4_DATA5 0x17059 + MX6SX_PAD_SD4_DATA6__USDHC4_DATA6 0x17059 + MX6SX_PAD_SD4_DATA7__USDHC4_DATA7 0x17059 + MX6SX_PAD_SD4_RESET_B__USDHC4_RESET_B 0x17068 + >; + }; + + pinctrl_usdhc4_100mhz: usdhc4-100mhz { + fsl,pins = < + MX6SX_PAD_SD4_CLK__USDHC4_CLK 0x100b9 + MX6SX_PAD_SD4_CMD__USDHC4_CMD 0x170b9 + MX6SX_PAD_SD4_DATA0__USDHC4_DATA0 0x170b9 + MX6SX_PAD_SD4_DATA1__USDHC4_DATA1 0x170b9 + MX6SX_PAD_SD4_DATA2__USDHC4_DATA2 0x170b9 + MX6SX_PAD_SD4_DATA3__USDHC4_DATA3 0x170b9 + MX6SX_PAD_SD4_DATA4__USDHC4_DATA4 0x170b9 + MX6SX_PAD_SD4_DATA5__USDHC4_DATA5 0x170b9 + MX6SX_PAD_SD4_DATA6__USDHC4_DATA6 0x170b9 + MX6SX_PAD_SD4_DATA7__USDHC4_DATA7 0x170b9 + >; + }; + + pinctrl_usdhc4_200mhz: usdhc4-200mhz { + fsl,pins = < + MX6SX_PAD_SD4_CLK__USDHC4_CLK 0x100f9 + MX6SX_PAD_SD4_CMD__USDHC4_CMD 0x170f9 + MX6SX_PAD_SD4_DATA0__USDHC4_DATA0 0x170f9 + MX6SX_PAD_SD4_DATA1__USDHC4_DATA1 0x170f9 + MX6SX_PAD_SD4_DATA2__USDHC4_DATA2 0x170f9 + MX6SX_PAD_SD4_DATA3__USDHC4_DATA3 0x170f9 + MX6SX_PAD_SD4_DATA4__USDHC4_DATA4 0x170f9 + MX6SX_PAD_SD4_DATA5__USDHC4_DATA5 0x170f9 + MX6SX_PAD_SD4_DATA6__USDHC4_DATA6 0x170f9 + MX6SX_PAD_SD4_DATA7__USDHC4_DATA7 0x170f9 + >; + }; +}; + +&pcie { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pcie>; + reset-gpio = <&gpio4 6 GPIO_ACTIVE_HIGH>; + reset-gpio-active-high; + status = "okay"; +}; + +&pwm1 { + #pwm-cells = <2>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm1>; + status = "okay"; +}; + +&pwm2 { + #pwm-cells = <2>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm2>; + status = "okay"; +}; + +&pwm6 { + #pwm-cells = <2>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm6>; + status = "okay"; +}; + +®_arm { + vin-supply = <&sw1a_reg>; +}; + +®_soc { + vin-supply = <&sw1a_reg>; +}; + +&snvs_poweroff { + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + status = "okay"; +}; + +&usbotg1 { + vbus-supply = <®_usb_otg1_vbus>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb_otg1_id>; + status = "okay"; +}; + +&usbotg2 { + dr_mode = "host"; + status = "okay"; +}; + +&usdhc2 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc2_50mhz>; + pinctrl-1 = <&pinctrl_usdhc2_100mhz>; + pinctrl-2 = <&pinctrl_usdhc2_200mhz>; + cd-gpios = <&gpio3 28 GPIO_ACTIVE_LOW>; + keep-power-in-suspend; + status = "okay"; +}; + +&usdhc4 { + /* hs200-mode is currently unsupported because Vccq is on 3.1V, but + * not on necessary 1.8V. + */ + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc4_50mhz>; + pinctrl-1 = <&pinctrl_usdhc4_100mhz>; + pinctrl-2 = <&pinctrl_usdhc4_200mhz>; + bus-width = <8>; + keep-power-in-suspend; + non-removable; + cap-mmc-hw-reset; + status = "okay"; +}; |