diff options
Diffstat (limited to 'arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts')
| -rw-r--r-- | arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts | 87 |
1 files changed, 87 insertions, 0 deletions
diff --git a/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts b/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts new file mode 100644 index 000000000..5532db040 --- /dev/null +++ b/arch/arm/boot/dts/logicpd-torpedo-37xx-devkit.dts @@ -0,0 +1,87 @@ +// SPDX-License-Identifier: GPL-2.0-only + +/dts-v1/; + +#include "omap36xx.dtsi" +#include "logicpd-torpedo-som.dtsi" +#include "omap-gpmc-smsc9221.dtsi" +#include "logicpd-torpedo-baseboard.dtsi" + +/ { + model = "LogicPD Zoom DM3730 Torpedo + Wireless Development Kit"; + compatible = "logicpd,dm3730-torpedo-devkit", "ti,omap3630", "ti,omap3"; + + wl12xx_vmmc: wl12xx_vmmc { + compatible = "regulator-fixed"; + regulator-name = "vwl1271"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&gpio5 29 0>; /* gpio157 */ + startup-delay-us = <70000>; + enable-active-high; + vin-supply = <&vmmc2>; + }; +}; + +/* + * Only found on the wireless SOM. For the SOM without wireless, the pins for + * MMC3 can be routed with jumpers to the second MMC slot on the devkit and + * gpio157 is not connected. So this should be OK to keep common for now, + * probably device tree overlays is the way to go with the various SOM and + * jumpering combinations for the long run. + */ +&mmc3 { + interrupts-extended = <&intc 94 &omap3_pmx_core 0x136>; + pinctrl-0 = <&mmc3_pins &mmc3_core2_pins>; + pinctrl-names = "default"; + vmmc-supply = <&wl12xx_vmmc>; + non-removable; + bus-width = <4>; + cap-power-off-card; + #address-cells = <1>; + #size-cells = <0>; + wlcore: wlcore@2 { + compatible = "ti,wl1283"; + reg = <2>; + interrupt-parent = <&gpio5>; + interrupts = <24 IRQ_TYPE_EDGE_RISING>; /* gpio 152 */ + ref-clock-frequency = <26000000>; + tcxo-clock-frequency = <26000000>; + }; +}; + +&uart2 { + /delete-property/dma-names; + bluetooth { + compatible = "ti,wl1283-st"; + enable-gpios = <&gpio6 2 GPIO_ACTIVE_HIGH>; /* gpio 162 */ + max-speed = <3000000>; + }; +}; + +/* The DM3730 has a faster L3 than OMAP35, so increase pixel clock */ +&mt9p031_out { + pixel-clock-frequency = <90000000>; +}; + +&omap3_pmx_core { + mmc3_pins: pinmux_mm3_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat4.sdmmc3_dat0 */ + OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat5.sdmmc3_dat1 */ + OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat2 */ + OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat3 */ + OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT_PULLUP | MUX_MODE4) /* mcbsp4_clkx.gpio_152 */ + OMAP3_CORE1_IOPAD(0x218e, PIN_OUTPUT | MUX_MODE4) /* mcbsp1_fsr.gpio_157 */ + >; + }; +}; + +&omap3_pmx_core2 { + mmc3_core2_pins: pinmux_mmc3_core2_pins { + pinctrl-single,pins = < + OMAP3630_CORE2_IOPAD(0x25d8, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_clk.sdmmc3_clk */ + OMAP3630_CORE2_IOPAD(0x25da, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_ctl.sdmmc3_cmd */ + >; + }; +}; |