1 files changed, 124 insertions, 0 deletions
diff --git a/arch/arm/boot/dts/mmp3-dell-ariel.dts b/arch/arm/boot/dts/mmp3-dell-ariel.dts
new file mode 100644
index 000000000..fe3b1cd69
--- /dev/null
+++ b/arch/arm/boot/dts/mmp3-dell-ariel.dts
@@ -0,0 +1,124 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Dell Wyse 3020 a.k.a. "Ariel" a.k.a. Tx0D (T00D, T10D)
+ *
+ * Copyright (C) 2019 Lubomir Rintel <lkundrak@v3.sk>
+ */
+
+/dts-v1/;
+#include "mmp3.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+/ {
+	model = "Dell Ariel";
+	compatible = "dell,wyse-ariel", "marvell,mmp3";
+
+	aliases {
+		serial2 = &uart3;
+	};
+
+	chosen {
+		#address-cells = <0x1>;
+		#size-cells = <0x1>;
+		ranges;
+		bootargs = "earlyprintk=ttyS2,115200 console=ttyS2,115200";
+	};
+
+	memory@0 {
+		linux,usable-memory = <0x0 0x7f600000>;
+		available = <0x7f700000 0x7ff00000 0x00000000 0x7f600000>;
+		reg = <0x0 0x80000000>;
+		device_type = "memory";
+	};
+};
+
+&uart3 {
+	status = "okay";
+};
+
+&rtc {
+	status = "okay";
+};
+
+&usb_otg0 {
+	status = "okay";
+};
+
+&usb_otg_phy0 {
+	status = "okay";
+};
+
+&hsic0 {
+	status = "okay";
+
+	usb1@1 {
+		compatible = "usb424,2640";
+		reg = <0x01>;
+		#address-cells = <0x01>;
+		#size-cells = <0x00>;
+
+		mass-storage@1 {
+			compatible = "usb424,4040";
+			reg = <0x01>;
+			status = "disabled";
+		};
+	};
+};
+
+&hsic_phy0 {
+	status = "okay";
+	reset-gpios = <&gpio 63 GPIO_ACTIVE_HIGH>;
+};
+
+&mmc3 {
+	status = "okay";
+	max-frequency = <50000000>;
+	status = "okay";
+	bus-width = <8>;
+	non-removable;
+	cap-mmc-highspeed;
+};
+
+&twsi1 {
+	status = "okay";
+
+	rtc@68 {
+		compatible = "dallas,ds1338";
+		reg = <0x68>;
+		status = "okay";
+	};
+};
+
+&twsi3 {
+	status = "okay";
+};
+
+&twsi4 {
+	status = "okay";
+};
+
+&ssp1 {
+	status = "okay";
+	cs-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
+
+	firmware-flash@0 {
+		compatible = "winbond,w25q32", "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <104000000>;
+		m25p,fast-read;
+	};
+};
+
+&ssp2 {
+	cs-gpios = <&gpio 56 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&gpu_2d {
+	status = "okay";
+};
+
+&gpu_3d {
+	status = "okay";
+};