diff options
Diffstat (limited to 'arch/arm/boot/dts/r8a7745-iwg22d-sodimm.dts')
| -rw-r--r-- | arch/arm/boot/dts/r8a7745-iwg22d-sodimm.dts | 327 |
1 files changed, 327 insertions, 0 deletions
diff --git a/arch/arm/boot/dts/r8a7745-iwg22d-sodimm.dts b/arch/arm/boot/dts/r8a7745-iwg22d-sodimm.dts new file mode 100644 index 000000000..1c7b37a01 --- /dev/null +++ b/arch/arm/boot/dts/r8a7745-iwg22d-sodimm.dts @@ -0,0 +1,327 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * Device Tree Source for the iWave-RZG1E SODIMM carrier board + * + * Copyright (C) 2017 Renesas Electronics Corp. + */ + +/* + * SSI-SGTL5000 + * + * This command is required when Playback/Capture + * + * amixer set "DVC Out" 100% + * amixer set "DVC In" 100% + * + * You can use Mute + * + * amixer set "DVC Out Mute" on + * amixer set "DVC In Mute" on + * + * You can use Volume Ramp + * + * amixer set "DVC Out Ramp Up Rate" "0.125 dB/64 steps" + * amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps" + * amixer set "DVC Out Ramp" on + * aplay xxx.wav & + * amixer set "DVC Out" 80% // Volume Down + * amixer set "DVC Out" 100% // Volume Up + */ + +/dts-v1/; +#include "r8a7745-iwg22m.dtsi" +#include <dt-bindings/pwm/pwm.h> + +/ { + model = "iWave Systems RainboW-G22D-SODIMM board based on RZ/G1E"; + compatible = "iwave,g22d", "iwave,g22m", "renesas,r8a7745"; + + aliases { + ethernet0 = &avb; + serial3 = &scif4; + serial5 = &hscif1; + }; + + chosen { + bootargs = "ignore_loglevel rw root=/dev/nfs ip=on"; + stdout-path = "serial3:115200n8"; + }; + + audio_clock: audio_clock { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <26000000>; + }; + + backlight_lcd: backlight { + compatible = "pwm-backlight"; + pwms = <&tpu 3 5000000 PWM_POLARITY_INVERTED>; + brightness-levels = <0 4 8 16 32 64 128 255>; + default-brightness-level = <7>; + }; + + lcd_panel: lcd { + compatible = "edt,etm043080dh6gp"; + power-supply = <&vccq_panel>; + backlight = <&backlight_lcd>; + + port { + lcd_in: endpoint { + remote-endpoint = <&du_out_rgb0>; + }; + }; + }; + + vccq_panel: regulator-vccq-panel { + compatible = "regulator-fixed"; + regulator-name = "Panel VccQ"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio1 13 GPIO_ACTIVE_LOW>; + enable-active-high; + }; + + vccq_sdhi0: regulator-vccq-sdhi0 { + compatible = "regulator-gpio"; + + regulator-name = "SDHI0 VccQ"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + + gpios = <&gpio0 20 GPIO_ACTIVE_LOW>; + gpios-states = <1>; + states = <3300000 1>, <1800000 0>; + }; + + rsnd_sgtl5000: sound { + compatible = "simple-audio-card"; + simple-audio-card,format = "i2s"; + simple-audio-card,bitclock-master = <&sndcodec>; + simple-audio-card,frame-master = <&sndcodec>; + + sndcpu: simple-audio-card,cpu { + sound-dai = <&rcar_sound>; + }; + + sndcodec: simple-audio-card,codec { + sound-dai = <&sgtl5000>; + }; + }; +}; + +&avb { + pinctrl-0 = <&avb_pins>; + pinctrl-names = "default"; + + phy-handle = <&phy3>; + phy-mode = "gmii"; + renesas,no-ether-link; + status = "okay"; + + phy3: ethernet-phy@3 { + /* + * On some older versions of the platform (before R4.0) the phy address + * may be 1 or 3. The address is fixed to 3 for R4.0 onwards. + */ + reg = <3>; + micrel,led-mode = <1>; + }; +}; + +&can0 { + pinctrl-0 = <&can0_pins>; + pinctrl-names = "default"; + + status = "okay"; +}; + +&du { + pinctrl-0 = <&du0_pins>; + pinctrl-names = "default"; + + status = "okay"; + + ports { + port@0 { + endpoint { + remote-endpoint = <&lcd_in>; + }; + }; + }; +}; + +&hscif1 { + pinctrl-0 = <&hscif1_pins>; + pinctrl-names = "default"; + + uart-has-rtscts; + status = "okay"; +}; + +&hsusb { + status = "okay"; + pinctrl-0 = <&usb0_pins>; + pinctrl-names = "default"; +}; + +&i2c5 { + pinctrl-0 = <&i2c5_pins>; + pinctrl-names = "default"; + + status = "okay"; + clock-frequency = <400000>; + + sgtl5000: codec@a { + compatible = "fsl,sgtl5000"; + #sound-dai-cells = <0>; + reg = <0x0a>; + clocks = <&audio_clock>; + VDDA-supply = <®_3p3v>; + VDDIO-supply = <®_3p3v>; + }; + + stmpe811@44 { + compatible = "st,stmpe811"; + reg = <0x44>; + interrupt-parent = <&gpio4>; + interrupts = <4 IRQ_TYPE_LEVEL_LOW>; + + /* 3.25 MHz ADC clock speed */ + st,adc-freq = <1>; + /* ADC conversion time: 80 clocks */ + st,sample-time = <4>; + /* 12-bit ADC */ + st,mod-12b = <1>; + /* internal ADC reference */ + st,ref-sel = <0>; + + stmpe_touchscreen { + compatible = "st,stmpe-ts"; + /* 8 sample average control */ + st,ave-ctrl = <3>; + /* 7 length fractional part in z */ + st,fraction-z = <7>; + /* + * 50 mA typical 80 mA max touchscreen drivers + * current limit value + */ + st,i-drive = <1>; + /* 1 ms panel driver settling time */ + st,settling = <3>; + /* 5 ms touch detect interrupt delay */ + st,touch-det-delay = <5>; + }; + }; +}; + +&pci1 { + status = "okay"; + pinctrl-0 = <&usb1_pins>; + pinctrl-names = "default"; +}; + +&pfc { + avb_pins: avb { + groups = "avb_mdio", "avb_gmii"; + function = "avb"; + }; + + backlight_pins: backlight { + groups = "tpu_to3_c"; + function = "tpu"; + }; + + can0_pins: can0 { + groups = "can0_data"; + function = "can0"; + }; + + du0_pins: du0 { + groups = "du0_rgb666", "du0_sync", "du0_disp", "du0_clk0_out"; + function = "du0"; + }; + + hscif1_pins: hscif1 { + groups = "hscif1_data", "hscif1_ctrl"; + function = "hscif1"; + }; + + i2c5_pins: i2c5 { + groups = "i2c5_b"; + function = "i2c5"; + }; + + scif4_pins: scif4 { + groups = "scif4_data_b"; + function = "scif4"; + }; + + sdhi0_pins: sd0 { + groups = "sdhi0_data4", "sdhi0_ctrl"; + function = "sdhi0"; + power-source = <3300>; + }; + + sound_pins: sound { + groups = "ssi34_ctrl", "ssi3_data", "ssi4_data"; + function = "ssi"; + }; + + usb0_pins: usb0 { + groups = "usb0"; + function = "usb0"; + }; + + usb1_pins: usb1 { + groups = "usb1"; + function = "usb1"; + }; +}; + +&rcar_sound { + pinctrl-0 = <&sound_pins>; + pinctrl-names = "default"; + status = "okay"; + + /* Single DAI */ + + #sound-dai-cells = <0>; + + rcar_sound,dai { + dai0 { + playback = <&ssi3 &src3 &dvc0>; + capture = <&ssi4 &src4 &dvc1>; + }; + }; +}; + +&scif4 { + pinctrl-0 = <&scif4_pins>; + pinctrl-names = "default"; + + status = "okay"; +}; + +&sdhi0 { + pinctrl-0 = <&sdhi0_pins>; + pinctrl-names = "default"; + + vmmc-supply = <®_3p3v>; + vqmmc-supply = <&vccq_sdhi0>; + cd-gpios = <&gpio6 6 GPIO_ACTIVE_LOW>; + status = "okay"; +}; + +&ssi4 { + shared-pin; +}; + +&tpu { + pinctrl-0 = <&backlight_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&usbphy { + status = "okay"; +}; |