diff options
Diffstat (limited to 'arch/arm/boot/dts/ste-hrefv60plus.dtsi')
| -rw-r--r-- | arch/arm/boot/dts/ste-hrefv60plus.dtsi | 335 |
1 files changed, 335 insertions, 0 deletions
diff --git a/arch/arm/boot/dts/ste-hrefv60plus.dtsi b/arch/arm/boot/dts/ste-hrefv60plus.dtsi new file mode 100644 index 000000000..05b4fbbba --- /dev/null +++ b/arch/arm/boot/dts/ste-hrefv60plus.dtsi @@ -0,0 +1,335 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * Copyright 2012 ST-Ericsson AB + */ + +#include "ste-href-ab8500.dtsi" +#include "ste-href.dtsi" + +/ { + model = "ST-Ericsson HREF (v60+) platform with Device Tree"; + compatible = "st-ericsson,hrefv60+", "st-ericsson,u8500"; + + soc { + /* Name the GPIO muxed rails on the HREF boards */ + gpio@8012e000 { + /* GPIOs 0 - 31 */ + gpio-line-names = + /* GPIO0,1 used for UART0 BT RX/TX */ + "", "", + "UART_WAKE", + "BT_WAKE", + "", + "SDMMC_1V8_3V_SEL", + "FLASH_LED_SYNC (FLASH_CTRL_0)", + "XENON_READY (FLASH_CTRL_1)", + "", "", "", "", "", "", "", "", + "", "", "", "", + "", + "FLASH_LED_EN (FLASH_CTRL_3)", + "", "", + "", "", "", "", "", + /* Used by UART2 (console) */ + "", "", + "MAGNETOMETER_INT"; + }; + + gpio@8012e080 { + /* GPIOs 32 - 63 */ + gpio-line-names = + "MAGNETOMETER_DRDY", + "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", ""; + }; + + gpio@8000e000 { + /* GPIOs 64 - 95 */ + gpio-line-names = "XENON_EN2 (FLASH_CTRL_4)", + "DISP1_RST", + "DISP2_RST", + "TOUCH_INT2", + "LCD_VSI0_A", + "LCD_VSI1_A", + /* GPIO 70-77 used for ETM */ + "", "", "", "", "", "", "", "", + /* GPIO 78-81 used for YCBCR */ + "", "", "", "", + "ACCELEROMETER_INT1_RDY", + "ACCELEROMETER_INT2", + "TOUCH_INT", + "WLAN_ENA", + "", "", "", "", "", + "FORCE_SENSING_INT", + "FORCE_SENSING_RESET", + "", "", + "SDMMC_CD"; + }; + + gpio@8000e080 { + /* GPIOs 96 - 127 */ + gpio-line-names = "", + "FORCE_SENSING_WU", + "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", ""; + }; + + gpio@8000e100 { + /* GPIOs 128 - 159 */ + gpio-line-names = "", "", "", "", "", "", "", "", + "", "", "", + "DIPRO_INT", /* GPIO139 */ + "XSHUTDOWN_SECONDARY_SENSOR", + "XSHUTDOWN_PRIMARY_SENSOR", + "NFC_RST (NFC_CTRL_", + "TOUCH_RST", + "NFC_IRQ (NFC_CTRL_1)", + "HAL_SW", + "TOUCH_RST2", + "", "", + "VAUDIO_HF_EN", /* GPIO149 */ + "", "", "", "", "", "", "", "", "", ""; + }; + + gpio@8000e180 { + /* GPIOs 160 - 191 */ + gpio-line-names = "", "", "", "", "", "", "", "", + "", + "SDMMC_EN", + "XENON_CHARGE (FLASH_CONTROL_5)", + "GBF_ENA_RESET", + "", "", "", "", + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", ""; + }; + + gpio@8011e000 { + /* GPIOs 192 - 223 */ + gpio-line-names = "HDTV_INTN", + "", "", "", + "HDTV_RSTN", + "", "", "", + "", /* GPIO200 */ + "", "", "", "", "", "", "", + /* GPIO208-216 used for WGBF_MC1 */ + "", "", "", "", "", "", "", "", "", + "SW_FRONT_PROXIMITY", /* GPIO217 */ + "KPD_CTRL_INT", /* Keypad controller */ + "", "", "", "", ""; + }; + + gpio@8011e080 { + /* GPIOs 224 - 255 */ + gpio-line-names = "", "", + "HSIT_ACWAKE0", + "", "", "", "", "", + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", ""; + }; + + // External Micro SD slot + sdi0_per1@80126000 { + cd-gpios = <&gpio2 31 GPIO_ACTIVE_HIGH>; // 95 + }; + + vmmci: regulator-gpio { + gpios = <&gpio0 5 GPIO_ACTIVE_HIGH>; + enable-gpio = <&gpio5 9 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + pinctrl { + /* + * Set this up using hogs, as time goes by and as seems fit, these + * can be moved over to being controlled by respective device. + */ + pinctrl-names = "default"; + pinctrl-0 = <&ipgpio_hrefv60_mode>, + <&etm_hrefv60_mode>, + <&nahj_hrefv60_mode>, + <&nfc_hrefv60_mode>, + <&force_hrefv60_mode>, + <&dipro_hrefv60_mode>, + <&vaudio_hf_hrefv60_mode>, + <&gbf_hrefv60_mode>, + <&hdtv_hrefv60_mode>, + <&gpios_hrefv60_mode>; + + sdi0 { + sdi0_default_mode: sdi0_default { + /* SD card detect GPIO pin, extend default state */ + default_hrefv60_cfg1 { + pins = "GPIO95_E8"; + ste,config = <&gpio_in_pu>; + }; + /* VMMCI level-shifter enable */ + default_hrefv60_cfg2 { + pins = "GPIO169_D22"; + ste,config = <&gpio_out_hi>; + }; + /* VMMCI level-shifter voltage select */ + default_hrefv60_cfg3 { + pins = "GPIO5_AG6"; + ste,config = <&gpio_out_hi>; + }; + }; + }; + ipgpio { + /* + * XENON Flashgun on image processor GPIO (controlled from image + * processor firmware), mux in these image processor GPIO lines 0 + * (XENON_FLASH_ID), 1 (XENON_READY) and there is an assistant + * LED on IP GPIO 4 (XENON_EN2) on altfunction C, that need bias + * from GPIO21 so pull up 0, 1 and drive 4 and GPIO21 low as output. + */ + ipgpio_hrefv60_mode: ipgpio_hrefv60 { + hrefv60_mux { + function = "ipgpio"; + groups = "ipgpio0_c_1", "ipgpio1_c_1", "ipgpio4_c_1"; + }; + hrefv60_cfg1 { + pins = "GPIO6_AF6", "GPIO7_AG5"; + ste,config = <&in_pu>; + }; + hrefv60_cfg2 { + pins = "GPIO21_AB3"; + ste,config = <&gpio_out_lo>; + }; + hrefv60_cfg3 { + pins = "GPIO64_F3"; + ste,config = <&out_lo>; + }; + }; + }; + etm { + /* + * Drive D19-D23 for the ETM PTM trace interface low, + * (presumably pins are unconnected therefore grounded here, + * the "other alt C1" setting enables these pins) + */ + etm_hrefv60_mode: etm_hrefv60 { + hrefv60_cfg1 { + pins = + "GPIO70_G5", + "GPIO71_G4", + "GPIO72_H4", + "GPIO73_H3", + "GPIO74_J3"; + ste,config = <&gpio_out_lo>; + }; + }; + }; + nahj { + nahj_hrefv60_mode: nahj_hrefv60 { + /* NAHJ CTRL on GPIO76 to low, CTRL_INV on GPIO216 to high */ + hrefv60_cfg1 { + pins = "GPIO76_J2"; + ste,config = <&gpio_out_lo>; + }; + hrefv60_cfg2 { + pins = "GPIO216_AG12"; + ste,config = <&gpio_out_hi>; + }; + }; + }; + nfc { + nfc_hrefv60_mode: nfc_hrefv60 { + /* NFC ENA and RESET to low, pulldown IRQ line */ + hrefv60_cfg1 { + pins = + "GPIO77_H1", /* NFC_ENA */ + "GPIO142_C11"; /* NFC_RESET */ + ste,config = <&gpio_out_lo>; + }; + hrefv60_cfg2 { + pins = "GPIO144_B13"; /* NFC_IRQ */ + ste,config = <&gpio_in_pd>; + }; + }; + }; + force { + force_hrefv60_mode: force_hrefv60 { + hrefv60_cfg1 { + pins = "GPIO91_B6"; /* FORCE_SENSING_INT */ + ste,config = <&gpio_in_pu>; + }; + hrefv60_cfg2 { + pins = + "GPIO92_D6", /* FORCE_SENSING_RST */ + "GPIO97_D9"; /* FORCE_SENSING_WU */ + ste,config = <&gpio_out_lo>; + }; + }; + }; + dipro { + dipro_hrefv60_mode: dipro_hrefv60 { + hrefv60_cfg1 { + pins = "GPIO139_C9"; /* DIPRO_INT */ + ste,config = <&gpio_in_pu>; + }; + }; + }; + vaudio_hf { + vaudio_hf_hrefv60_mode: vaudio_hf_hrefv60 { + /* Audio Amplifier HF enable GPIO */ + hrefv60_cfg1 { + pins = "GPIO149_B14"; /* VAUDIO_HF_EN, enable MAX8968 */ + ste,config = <&gpio_out_hi>; + }; + }; + }; + gbf { + gbf_hrefv60_mode: gbf_hrefv60 { + /* + * GBF (GPS, Bluetooth, FM-radio) interface, + * pull low to reset state + */ + hrefv60_cfg1 { + pins = "GPIO171_D23"; /* GBF_ENA_RESET */ + ste,config = <&gpio_out_lo>; + }; + }; + }; + hdtv { + hdtv_hrefv60_mode: hdtv_hrefv60 { + /* MSP : HDTV INTERFACE GPIO line */ + hrefv60_cfg1 { + pins = "GPIO192_AJ27"; + ste,config = <&gpio_in_pd>; + }; + }; + }; + mcde { + lcd_hrefv60_mode: lcd_hrefv60 { + /* + * Display Interface 1 uses GPIO 65 for RST (reset). + * Display Interface 2 uses GPIO 66 for RST (reset). + * Drive DISP1 reset high (not reset), driver DISP2 reset low (reset) + */ + hrefv60_cfg1 { + pins ="GPIO65_F1"; + ste,config = <&gpio_out_hi>; + }; + hrefv60_cfg2 { + pins ="GPIO66_G3"; + ste,config = <&gpio_out_lo>; + }; + }; + }; + gpios { + /* Dangling GPIO pins */ + gpios_hrefv60_mode: gpios_hrefv60 { + default_cfg1 { + /* Normally UART1 RXD, now dangling */ + pins = "GPIO4_AH6"; + ste,config = <&in_pu>; + }; + }; + }; + }; + }; +}; |