diff options
Diffstat (limited to 'arch/arm/boot/dts/vexpress-v2m.dtsi')
| -rw-r--r-- | arch/arm/boot/dts/vexpress-v2m.dtsi | 454 |
1 files changed, 454 insertions, 0 deletions
diff --git a/arch/arm/boot/dts/vexpress-v2m.dtsi b/arch/arm/boot/dts/vexpress-v2m.dtsi new file mode 100644 index 000000000..659dcf400 --- /dev/null +++ b/arch/arm/boot/dts/vexpress-v2m.dtsi @@ -0,0 +1,454 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * ARM Ltd. Versatile Express + * + * Motherboard Express uATX + * V2M-P1 + * + * HBI-0190D + * + * Original memory map ("Legacy memory map" in the board's + * Technical Reference Manual) + * + * WARNING! The hardware described in this file is independent from the + * RS1 variant (vexpress-v2m-rs1.dtsi), but there is a strong + * correspondence between the two configurations. + * + * TAKE CARE WHEN MAINTAINING THIS FILE TO PROPAGATE ANY RELEVANT + * CHANGES TO vexpress-v2m-rs1.dtsi! + */ + +/ { + bus@40000000 { + motherboard { + model = "V2M-P1"; + arm,hbi = <0x190>; + arm,vexpress,site = <0>; + compatible = "arm,vexpress,v2m-p1", "simple-bus"; + #address-cells = <2>; /* SMB chipselect number and offset */ + #size-cells = <1>; + #interrupt-cells = <1>; + ranges; + + flash@0,00000000 { + compatible = "arm,vexpress-flash", "cfi-flash"; + reg = <0 0x00000000 0x04000000>, + <1 0x00000000 0x04000000>; + bank-width = <4>; + partitions { + compatible = "arm,arm-firmware-suite"; + }; + }; + + psram@2,00000000 { + compatible = "arm,vexpress-psram", "mtd-ram"; + reg = <2 0x00000000 0x02000000>; + bank-width = <4>; + }; + + ethernet@3,02000000 { + compatible = "smsc,lan9118", "smsc,lan9115"; + reg = <3 0x02000000 0x10000>; + interrupts = <15>; + phy-mode = "mii"; + reg-io-width = <4>; + smsc,irq-active-high; + smsc,irq-push-pull; + vdd33a-supply = <&v2m_fixed_3v3>; + vddvario-supply = <&v2m_fixed_3v3>; + }; + + usb@3,03000000 { + compatible = "nxp,usb-isp1761"; + reg = <3 0x03000000 0x20000>; + interrupts = <16>; + port1-otg; + }; + + iofpga@7,00000000 { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 7 0 0x20000>; + + v2m_sysreg: sysreg@0 { + compatible = "arm,vexpress-sysreg"; + reg = <0x00000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0 0x1000>; + + v2m_led_gpios: gpio@8 { + compatible = "arm,vexpress-sysreg,sys_led"; + reg = <0x008 4>; + gpio-controller; + #gpio-cells = <2>; + }; + + v2m_mmc_gpios: gpio@48 { + compatible = "arm,vexpress-sysreg,sys_mci"; + reg = <0x048 4>; + gpio-controller; + #gpio-cells = <2>; + }; + + v2m_flash_gpios: gpio@4c { + compatible = "arm,vexpress-sysreg,sys_flash"; + reg = <0x04c 4>; + gpio-controller; + #gpio-cells = <2>; + }; + }; + + v2m_sysctl: sysctl@1000 { + compatible = "arm,sp810", "arm,primecell"; + reg = <0x01000 0x1000>; + clocks = <&v2m_refclk32khz>, <&v2m_refclk1mhz>, <&smbclk>; + clock-names = "refclk", "timclk", "apb_pclk"; + #clock-cells = <1>; + clock-output-names = "timerclken0", "timerclken1", "timerclken2", "timerclken3"; + assigned-clocks = <&v2m_sysctl 0>, <&v2m_sysctl 1>, <&v2m_sysctl 3>, <&v2m_sysctl 3>; + assigned-clock-parents = <&v2m_refclk1mhz>, <&v2m_refclk1mhz>, <&v2m_refclk1mhz>, <&v2m_refclk1mhz>; + }; + + /* PCI-E I2C bus */ + v2m_i2c_pcie: i2c@2000 { + compatible = "arm,versatile-i2c"; + reg = <0x02000 0x1000>; + + #address-cells = <1>; + #size-cells = <0>; + + pcie-switch@60 { + compatible = "idt,89hpes32h8"; + reg = <0x60>; + }; + }; + + aaci@4000 { + compatible = "arm,pl041", "arm,primecell"; + reg = <0x04000 0x1000>; + interrupts = <11>; + clocks = <&smbclk>; + clock-names = "apb_pclk"; + }; + + mmci@5000 { + compatible = "arm,pl180", "arm,primecell"; + reg = <0x05000 0x1000>; + interrupts = <9>, <10>; + cd-gpios = <&v2m_mmc_gpios 0 0>; + wp-gpios = <&v2m_mmc_gpios 1 0>; + max-frequency = <12000000>; + vmmc-supply = <&v2m_fixed_3v3>; + clocks = <&v2m_clk24mhz>, <&smbclk>; + clock-names = "mclk", "apb_pclk"; + }; + + kmi@6000 { + compatible = "arm,pl050", "arm,primecell"; + reg = <0x06000 0x1000>; + interrupts = <12>; + clocks = <&v2m_clk24mhz>, <&smbclk>; + clock-names = "KMIREFCLK", "apb_pclk"; + }; + + kmi@7000 { + compatible = "arm,pl050", "arm,primecell"; + reg = <0x07000 0x1000>; + interrupts = <13>; + clocks = <&v2m_clk24mhz>, <&smbclk>; + clock-names = "KMIREFCLK", "apb_pclk"; + }; + + v2m_serial0: uart@9000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x09000 0x1000>; + interrupts = <5>; + clocks = <&v2m_oscclk2>, <&smbclk>; + clock-names = "uartclk", "apb_pclk"; + }; + + v2m_serial1: uart@a000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x0a000 0x1000>; + interrupts = <6>; + clocks = <&v2m_oscclk2>, <&smbclk>; + clock-names = "uartclk", "apb_pclk"; + }; + + v2m_serial2: uart@b000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x0b000 0x1000>; + interrupts = <7>; + clocks = <&v2m_oscclk2>, <&smbclk>; + clock-names = "uartclk", "apb_pclk"; + }; + + v2m_serial3: uart@c000 { + compatible = "arm,pl011", "arm,primecell"; + reg = <0x0c000 0x1000>; + interrupts = <8>; + clocks = <&v2m_oscclk2>, <&smbclk>; + clock-names = "uartclk", "apb_pclk"; + }; + + wdt@f000 { + compatible = "arm,sp805", "arm,primecell"; + reg = <0x0f000 0x1000>; + interrupts = <0>; + clocks = <&v2m_refclk32khz>, <&smbclk>; + clock-names = "wdog_clk", "apb_pclk"; + }; + + v2m_timer01: timer@11000 { + compatible = "arm,sp804", "arm,primecell"; + reg = <0x11000 0x1000>; + interrupts = <2>; + clocks = <&v2m_sysctl 0>, <&v2m_sysctl 1>, <&smbclk>; + clock-names = "timclken1", "timclken2", "apb_pclk"; + }; + + v2m_timer23: timer@12000 { + compatible = "arm,sp804", "arm,primecell"; + reg = <0x12000 0x1000>; + interrupts = <3>; + clocks = <&v2m_sysctl 2>, <&v2m_sysctl 3>, <&smbclk>; + clock-names = "timclken1", "timclken2", "apb_pclk"; + }; + + /* DVI I2C bus */ + v2m_i2c_dvi: i2c@16000 { + compatible = "arm,versatile-i2c"; + reg = <0x16000 0x1000>; + #address-cells = <1>; + #size-cells = <0>; + + dvi-transmitter@39 { + compatible = "sil,sii9022-tpi", "sil,sii9022"; + reg = <0x39>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + /* + * Both the core tile and the motherboard routes their output + * pads to this transmitter. The motherboard system controller + * can select one of them as input using a mux register in + * "arm,vexpress-muxfpga". The Vexpress with the CA9 core tile is + * the only platform with this specific set-up. + */ + port@0 { + reg = <0>; + dvi_bridge_in_ct: endpoint { + remote-endpoint = <&clcd_pads_ct>; + }; + }; + port@1 { + reg = <1>; + dvi_bridge_in_mb: endpoint { + remote-endpoint = <&clcd_pads_mb>; + }; + }; + }; + }; + + dvi-transmitter@60 { + compatible = "sil,sii9022-cpi", "sil,sii9022"; + reg = <0x60>; + }; + }; + + rtc@17000 { + compatible = "arm,pl031", "arm,primecell"; + reg = <0x17000 0x1000>; + interrupts = <4>; + clocks = <&smbclk>; + clock-names = "apb_pclk"; + }; + + compact-flash@1a000 { + compatible = "arm,vexpress-cf", "ata-generic"; + reg = <0x1a000 0x100 + 0x1a100 0xf00>; + reg-shift = <2>; + }; + + + clcd@1f000 { + compatible = "arm,pl111", "arm,primecell"; + reg = <0x1f000 0x1000>; + interrupt-names = "combined"; + interrupts = <14>; + clocks = <&v2m_oscclk1>, <&smbclk>; + clock-names = "clcdclk", "apb_pclk"; + /* 800x600 16bpp @36MHz works fine */ + max-memory-bandwidth = <54000000>; + memory-region = <&vram>; + + port { + clcd_pads_mb: endpoint { + remote-endpoint = <&dvi_bridge_in_mb>; + arm,pl11x,tft-r0g0b0-pads = <0 8 16>; + }; + }; + }; + }; + + v2m_fixed_3v3: fixed-regulator-0 { + compatible = "regulator-fixed"; + regulator-name = "3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + v2m_clk24mhz: clk24mhz { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <24000000>; + clock-output-names = "v2m:clk24mhz"; + }; + + v2m_refclk1mhz: refclk1mhz { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <1000000>; + clock-output-names = "v2m:refclk1mhz"; + }; + + v2m_refclk32khz: refclk32khz { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <32768>; + clock-output-names = "v2m:refclk32khz"; + }; + + leds { + compatible = "gpio-leds"; + + user1 { + label = "v2m:green:user1"; + gpios = <&v2m_led_gpios 0 0>; + linux,default-trigger = "heartbeat"; + }; + + user2 { + label = "v2m:green:user2"; + gpios = <&v2m_led_gpios 1 0>; + linux,default-trigger = "mmc0"; + }; + + user3 { + label = "v2m:green:user3"; + gpios = <&v2m_led_gpios 2 0>; + linux,default-trigger = "cpu0"; + }; + + user4 { + label = "v2m:green:user4"; + gpios = <&v2m_led_gpios 3 0>; + linux,default-trigger = "cpu1"; + }; + + user5 { + label = "v2m:green:user5"; + gpios = <&v2m_led_gpios 4 0>; + linux,default-trigger = "cpu2"; + }; + + user6 { + label = "v2m:green:user6"; + gpios = <&v2m_led_gpios 5 0>; + linux,default-trigger = "cpu3"; + }; + + user7 { + label = "v2m:green:user7"; + gpios = <&v2m_led_gpios 6 0>; + linux,default-trigger = "cpu4"; + }; + + user8 { + label = "v2m:green:user8"; + gpios = <&v2m_led_gpios 7 0>; + linux,default-trigger = "cpu5"; + }; + }; + + mcc { + compatible = "arm,vexpress,config-bus"; + arm,vexpress,config-bridge = <&v2m_sysreg>; + + oscclk0 { + /* MCC static memory clock */ + compatible = "arm,vexpress-osc"; + arm,vexpress-sysreg,func = <1 0>; + freq-range = <25000000 60000000>; + #clock-cells = <0>; + clock-output-names = "v2m:oscclk0"; + }; + + v2m_oscclk1: oscclk1 { + /* CLCD clock */ + compatible = "arm,vexpress-osc"; + arm,vexpress-sysreg,func = <1 1>; + freq-range = <23750000 65000000>; + #clock-cells = <0>; + clock-output-names = "v2m:oscclk1"; + }; + + v2m_oscclk2: oscclk2 { + /* IO FPGA peripheral clock */ + compatible = "arm,vexpress-osc"; + arm,vexpress-sysreg,func = <1 2>; + freq-range = <24000000 24000000>; + #clock-cells = <0>; + clock-output-names = "v2m:oscclk2"; + }; + + volt-vio { + /* Logic level voltage */ + compatible = "arm,vexpress-volt"; + arm,vexpress-sysreg,func = <2 0>; + regulator-name = "VIO"; + regulator-always-on; + label = "VIO"; + }; + + temp-mcc { + /* MCC internal operating temperature */ + compatible = "arm,vexpress-temp"; + arm,vexpress-sysreg,func = <4 0>; + label = "MCC"; + }; + + reset { + compatible = "arm,vexpress-reset"; + arm,vexpress-sysreg,func = <5 0>; + }; + + muxfpga { + compatible = "arm,vexpress-muxfpga"; + arm,vexpress-sysreg,func = <7 0>; + }; + + shutdown { + compatible = "arm,vexpress-shutdown"; + arm,vexpress-sysreg,func = <8 0>; + }; + + reboot { + compatible = "arm,vexpress-reboot"; + arm,vexpress-sysreg,func = <9 0>; + }; + + dvimode { + compatible = "arm,vexpress-dvimode"; + arm,vexpress-sysreg,func = <11 0>; + }; + }; + }; + }; +}; |