diff options
Diffstat (limited to 'arch/arm/mach-pxa/include/mach')
34 files changed, 3535 insertions, 0 deletions
diff --git a/arch/arm/mach-pxa/include/mach/addr-map.h b/arch/arm/mach-pxa/include/mach/addr-map.h new file mode 100644 index 000000000..93cfe7dbf --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/addr-map.h @@ -0,0 +1,61 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +#ifndef __ASM_MACH_ADDR_MAP_H +#define __ASM_MACH_ADDR_MAP_H + +/* + * Chip Selects + */ +#define PXA_CS0_PHYS 0x00000000 +#define PXA_CS1_PHYS 0x04000000 +#define PXA_CS2_PHYS 0x08000000 +#define PXA_CS3_PHYS 0x0C000000 +#define PXA_CS4_PHYS 0x10000000 +#define PXA_CS5_PHYS 0x14000000 + +#define PXA300_CS0_PHYS 0x00000000 /* PXA300/PXA310 _only_ */ +#define PXA300_CS1_PHYS 0x30000000 /* PXA300/PXA310 _only_ */ +#define PXA3xx_CS2_PHYS 0x10000000 +#define PXA3xx_CS3_PHYS 0x14000000 + +/* + * Peripheral Bus + */ +#define PERIPH_PHYS 0x40000000 +#define PERIPH_VIRT IOMEM(0xf2000000) +#define PERIPH_SIZE 0x02000000 + +/* + * Static Memory Controller (w/ SDRAM controls on PXA25x/PXA27x) + */ +#define PXA2XX_SMEMC_PHYS 0x48000000 +#define PXA3XX_SMEMC_PHYS 0x4a000000 +#define SMEMC_VIRT IOMEM(0xf6000000) +#define SMEMC_SIZE 0x00100000 + +/* + * Dynamic Memory Controller (only on PXA3xx) + */ +#define DMEMC_PHYS 0x48100000 +#define DMEMC_VIRT IOMEM(0xf6100000) +#define DMEMC_SIZE 0x00100000 + +/* + * Reserved space for low level debug virtual addresses within + * 0xf6200000..0xf6201000 + */ + +/* + * DFI Bus for NAND, PXA3xx only + */ +#define NAND_PHYS 0x43100000 +#define NAND_VIRT IOMEM(0xf6300000) +#define NAND_SIZE 0x00100000 + +/* + * Internal Memory Controller (PXA27x and later) + */ +#define IMEMC_PHYS 0x58000000 +#define IMEMC_VIRT IOMEM(0xfe000000) +#define IMEMC_SIZE 0x00100000 + +#endif /* __ASM_MACH_ADDR_MAP_H */ diff --git a/arch/arm/mach-pxa/include/mach/audio.h b/arch/arm/mach-pxa/include/mach/audio.h new file mode 100644 index 000000000..7beebf729 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/audio.h @@ -0,0 +1,31 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +#ifndef __ASM_ARCH_AUDIO_H__ +#define __ASM_ARCH_AUDIO_H__ + +#include <sound/core.h> +#include <sound/pcm.h> +#include <sound/ac97_codec.h> + +/* + * @reset_gpio: AC97 reset gpio (normally gpio113 or gpio95) + * a -1 value means no gpio will be used for reset + * @codec_pdata: AC97 codec platform_data + + * reset_gpio should only be specified for pxa27x CPUs where a silicon + * bug prevents correct operation of the reset line. If not specified, + * the default behaviour on these CPUs is to consider gpio 113 as the + * AC97 reset line, which is the default on most boards. + */ +typedef struct { + int (*startup)(struct snd_pcm_substream *, void *); + void (*shutdown)(struct snd_pcm_substream *, void *); + void (*suspend)(void *); + void (*resume)(void *); + void *priv; + int reset_gpio; + void *codec_pdata[AC97_BUS_MAX_DEVICES]; +} pxa2xx_audio_ops_t; + +extern void pxa_set_ac97_info(pxa2xx_audio_ops_t *ops); + +#endif diff --git a/arch/arm/mach-pxa/include/mach/balloon3.h b/arch/arm/mach-pxa/include/mach/balloon3.h new file mode 100644 index 000000000..04f3639c4 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/balloon3.h @@ -0,0 +1,181 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ +/* + * linux/include/asm-arm/arch-pxa/balloon3.h + * + * Authors: Nick Bane and Wookey + * Created: Oct, 2005 + * Copyright: Toby Churchill Ltd + * Cribbed from mainstone.c, by Nicholas Pitre + */ + +#ifndef ASM_ARCH_BALLOON3_H +#define ASM_ARCH_BALLOON3_H + +#include "irqs.h" /* PXA_NR_BUILTIN_GPIO */ + +enum balloon3_features { + BALLOON3_FEATURE_OHCI, + BALLOON3_FEATURE_MMC, + BALLOON3_FEATURE_CF, + BALLOON3_FEATURE_AUDIO, + BALLOON3_FEATURE_TOPPOLY, +}; + +#define BALLOON3_FPGA_PHYS PXA_CS4_PHYS +#define BALLOON3_FPGA_VIRT IOMEM(0xf1000000) /* as per balloon2 */ +#define BALLOON3_FPGA_LENGTH 0x01000000 + +#define BALLOON3_FPGA_SETnCLR (0x1000) + +/* FPGA / CPLD registers for CF socket */ +#define BALLOON3_CF_STATUS_REG (BALLOON3_FPGA_VIRT + 0x00e00008) +#define BALLOON3_CF_CONTROL_REG (BALLOON3_FPGA_VIRT + 0x00e00008) +/* FPGA / CPLD version register */ +#define BALLOON3_FPGA_VER (BALLOON3_FPGA_VIRT + 0x00e0001c) +/* FPGA / CPLD registers for NAND flash */ +#define BALLOON3_NAND_BASE (PXA_CS4_PHYS + 0x00e00000) +#define BALLOON3_NAND_IO_REG (BALLOON3_FPGA_VIRT + 0x00e00000) +#define BALLOON3_NAND_CONTROL2_REG (BALLOON3_FPGA_VIRT + 0x00e00010) +#define BALLOON3_NAND_STAT_REG (BALLOON3_FPGA_VIRT + 0x00e00014) +#define BALLOON3_NAND_CONTROL_REG (BALLOON3_FPGA_VIRT + 0x00e00014) + +/* fpga/cpld interrupt control register */ +#define BALLOON3_INT_CONTROL_REG (BALLOON3_FPGA_VIRT + 0x00e0000C) +#define BALLOON3_VERSION_REG (BALLOON3_FPGA_VIRT + 0x00e0001c) + +#define BALLOON3_SAMOSA_ADDR_REG (BALLOON3_FPGA_VIRT + 0x00c00000) +#define BALLOON3_SAMOSA_DATA_REG (BALLOON3_FPGA_VIRT + 0x00c00004) +#define BALLOON3_SAMOSA_STATUS_REG (BALLOON3_FPGA_VIRT + 0x00c0001c) + +/* CF Status Register bits (read-only) bits */ +#define BALLOON3_CF_nIRQ (1 << 0) +#define BALLOON3_CF_nSTSCHG_BVD1 (1 << 1) + +/* CF Control Set Register bits / CF Control Clear Register bits (write-only) */ +#define BALLOON3_CF_RESET (1 << 0) +#define BALLOON3_CF_ENABLE (1 << 1) +#define BALLOON3_CF_ADD_ENABLE (1 << 2) + +/* CF Interrupt sources */ +#define BALLOON3_BP_CF_NRDY_IRQ BALLOON3_IRQ(0) +#define BALLOON3_BP_NSTSCHG_IRQ BALLOON3_IRQ(1) + +/* NAND Control register */ +#define BALLOON3_NAND_CONTROL_FLWP (1 << 7) +#define BALLOON3_NAND_CONTROL_FLSE (1 << 6) +#define BALLOON3_NAND_CONTROL_FLCE3 (1 << 5) +#define BALLOON3_NAND_CONTROL_FLCE2 (1 << 4) +#define BALLOON3_NAND_CONTROL_FLCE1 (1 << 3) +#define BALLOON3_NAND_CONTROL_FLCE0 (1 << 2) +#define BALLOON3_NAND_CONTROL_FLALE (1 << 1) +#define BALLOON3_NAND_CONTROL_FLCLE (1 << 0) + +/* NAND Status register */ +#define BALLOON3_NAND_STAT_RNB (1 << 0) + +/* NAND Control2 register */ +#define BALLOON3_NAND_CONTROL2_16BIT (1 << 0) + +/* GPIOs for irqs */ +#define BALLOON3_GPIO_AUX_NIRQ (94) +#define BALLOON3_GPIO_CODEC_IRQ (95) + +/* Timer and Idle LED locations */ +#define BALLOON3_GPIO_LED_NAND (9) +#define BALLOON3_GPIO_LED_IDLE (10) + +/* backlight control */ +#define BALLOON3_GPIO_RUN_BACKLIGHT (99) + +#define BALLOON3_GPIO_S0_CD (105) + +/* NAND */ +#define BALLOON3_GPIO_RUN_NAND (102) + +/* PCF8574A Leds */ +#define BALLOON3_PCF_GPIO_BASE 160 +#define BALLOON3_PCF_GPIO_LED0 (BALLOON3_PCF_GPIO_BASE + 0) +#define BALLOON3_PCF_GPIO_LED1 (BALLOON3_PCF_GPIO_BASE + 1) +#define BALLOON3_PCF_GPIO_LED2 (BALLOON3_PCF_GPIO_BASE + 2) +#define BALLOON3_PCF_GPIO_LED3 (BALLOON3_PCF_GPIO_BASE + 3) +#define BALLOON3_PCF_GPIO_LED4 (BALLOON3_PCF_GPIO_BASE + 4) +#define BALLOON3_PCF_GPIO_LED5 (BALLOON3_PCF_GPIO_BASE + 5) +#define BALLOON3_PCF_GPIO_LED6 (BALLOON3_PCF_GPIO_BASE + 6) +#define BALLOON3_PCF_GPIO_LED7 (BALLOON3_PCF_GPIO_BASE + 7) + +/* FPGA Interrupt Mask/Acknowledge Register */ +#define BALLOON3_INT_S0_IRQ (1 << 0) /* PCMCIA 0 IRQ */ +#define BALLOON3_INT_S0_STSCHG (1 << 1) /* PCMCIA 0 status changed */ + +/* CPLD (and FPGA) interface definitions */ +#define CPLD_LCD0_DATA_SET 0x00 +#define CPLD_LCD0_DATA_CLR 0x10 +#define CPLD_LCD0_COMMAND_SET 0x01 +#define CPLD_LCD0_COMMAND_CLR 0x11 +#define CPLD_LCD1_DATA_SET 0x02 +#define CPLD_LCD1_DATA_CLR 0x12 +#define CPLD_LCD1_COMMAND_SET 0x03 +#define CPLD_LCD1_COMMAND_CLR 0x13 + +#define CPLD_MISC_SET 0x07 +#define CPLD_MISC_CLR 0x17 +#define CPLD_MISC_LOON_NRESET_BIT 0 +#define CPLD_MISC_LOON_UNSUSP_BIT 1 +#define CPLD_MISC_RUN_5V_BIT 2 +#define CPLD_MISC_CHG_D0_BIT 3 +#define CPLD_MISC_CHG_D1_BIT 4 +#define CPLD_MISC_DAC_NCS_BIT 5 + +#define CPLD_LCD_SET 0x08 +#define CPLD_LCD_CLR 0x18 +#define CPLD_LCD_BACKLIGHT_EN_0_BIT 0 +#define CPLD_LCD_BACKLIGHT_EN_1_BIT 1 +#define CPLD_LCD_LED_RED_BIT 4 +#define CPLD_LCD_LED_GREEN_BIT 5 +#define CPLD_LCD_NRESET_BIT 7 + +#define CPLD_LCD_RO_SET 0x09 +#define CPLD_LCD_RO_CLR 0x19 +#define CPLD_LCD_RO_LCD0_nWAIT_BIT 0 +#define CPLD_LCD_RO_LCD1_nWAIT_BIT 1 + +#define CPLD_SERIAL_SET 0x0a +#define CPLD_SERIAL_CLR 0x1a +#define CPLD_SERIAL_GSM_RI_BIT 0 +#define CPLD_SERIAL_GSM_CTS_BIT 1 +#define CPLD_SERIAL_GSM_DTR_BIT 2 +#define CPLD_SERIAL_LPR_CTS_BIT 3 +#define CPLD_SERIAL_TC232_CTS_BIT 4 +#define CPLD_SERIAL_TC232_DSR_BIT 5 + +#define CPLD_SROUTING_SET 0x0b +#define CPLD_SROUTING_CLR 0x1b +#define CPLD_SROUTING_MSP430_LPR 0 +#define CPLD_SROUTING_MSP430_TC232 1 +#define CPLD_SROUTING_MSP430_GSM 2 +#define CPLD_SROUTING_LOON_LPR (0 << 4) +#define CPLD_SROUTING_LOON_TC232 (1 << 4) +#define CPLD_SROUTING_LOON_GSM (2 << 4) + +#define CPLD_AROUTING_SET 0x0c +#define CPLD_AROUTING_CLR 0x1c +#define CPLD_AROUTING_MIC2PHONE_BIT 0 +#define CPLD_AROUTING_PHONE2INT_BIT 1 +#define CPLD_AROUTING_PHONE2EXT_BIT 2 +#define CPLD_AROUTING_LOONL2INT_BIT 3 +#define CPLD_AROUTING_LOONL2EXT_BIT 4 +#define CPLD_AROUTING_LOONR2PHONE_BIT 5 +#define CPLD_AROUTING_LOONR2INT_BIT 6 +#define CPLD_AROUTING_LOONR2EXT_BIT 7 + +/* Balloon3 Interrupts */ +#define BALLOON3_IRQ(x) (IRQ_BOARD_START + (x)) + +#define BALLOON3_AUX_NIRQ PXA_GPIO_TO_IRQ(BALLOON3_GPIO_AUX_NIRQ) +#define BALLOON3_CODEC_IRQ PXA_GPIO_TO_IRQ(BALLOON3_GPIO_CODEC_IRQ) + +#define BALLOON3_NR_IRQS (IRQ_BOARD_START + 16) + +extern int balloon3_has(enum balloon3_features feature); + +#endif diff --git a/arch/arm/mach-pxa/include/mach/bitfield.h b/arch/arm/mach-pxa/include/mach/bitfield.h new file mode 100644 index 000000000..fe2ca441b --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/bitfield.h @@ -0,0 +1,114 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* + * FILE bitfield.h + * + * Version 1.1 + * Author Copyright (c) Marc A. Viredaz, 1998 + * DEC Western Research Laboratory, Palo Alto, CA + * Date April 1998 (April 1997) + * System Advanced RISC Machine (ARM) + * Language C or ARM Assembly + * Purpose Definition of macros to operate on bit fields. + */ + + + +#ifndef __BITFIELD_H +#define __BITFIELD_H + +#ifndef __ASSEMBLY__ +#define UData(Data) ((unsigned long) (Data)) +#else +#define UData(Data) (Data) +#endif + + +/* + * MACRO: Fld + * + * Purpose + * The macro "Fld" encodes a bit field, given its size and its shift value + * with respect to bit 0. + * + * Note + * A more intuitive way to encode bit fields would have been to use their + * mask. However, extracting size and shift value information from a bit + * field's mask is cumbersome and might break the assembler (255-character + * line-size limit). + * + * Input + * Size Size of the bit field, in number of bits. + * Shft Shift value of the bit field with respect to bit 0. + * + * Output + * Fld Encoded bit field. + */ + +#define Fld(Size, Shft) (((Size) << 16) + (Shft)) + + +/* + * MACROS: FSize, FShft, FMsk, FAlnMsk, F1stBit + * + * Purpose + * The macros "FSize", "FShft", "FMsk", "FAlnMsk", and "F1stBit" return + * the size, shift value, mask, aligned mask, and first bit of a + * bit field. + * + * Input + * Field Encoded bit field (using the macro "Fld"). + * + * Output + * FSize Size of the bit field, in number of bits. + * FShft Shift value of the bit field with respect to bit 0. + * FMsk Mask for the bit field. + * FAlnMsk Mask for the bit field, aligned on bit 0. + * F1stBit First bit of the bit field. + */ + +#define FSize(Field) ((Field) >> 16) +#define FShft(Field) ((Field) & 0x0000FFFF) +#define FMsk(Field) (((UData (1) << FSize (Field)) - 1) << FShft (Field)) +#define FAlnMsk(Field) ((UData (1) << FSize (Field)) - 1) +#define F1stBit(Field) (UData (1) << FShft (Field)) + + +/* + * MACRO: FInsrt + * + * Purpose + * The macro "FInsrt" inserts a value into a bit field by shifting the + * former appropriately. + * + * Input + * Value Bit-field value. + * Field Encoded bit field (using the macro "Fld"). + * + * Output + * FInsrt Bit-field value positioned appropriately. + */ + +#define FInsrt(Value, Field) \ + (UData (Value) << FShft (Field)) + + +/* + * MACRO: FExtr + * + * Purpose + * The macro "FExtr" extracts the value of a bit field by masking and + * shifting it appropriately. + * + * Input + * Data Data containing the bit-field to be extracted. + * Field Encoded bit field (using the macro "Fld"). + * + * Output + * FExtr Bit-field value. + */ + +#define FExtr(Data, Field) \ + ((UData (Data) >> FShft (Field)) & FAlnMsk (Field)) + + +#endif /* __BITFIELD_H */ diff --git a/arch/arm/mach-pxa/include/mach/corgi.h b/arch/arm/mach-pxa/include/mach/corgi.h new file mode 100644 index 000000000..b565ca7b8 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/corgi.h @@ -0,0 +1,110 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ +/* + * Hardware specific definitions for SL-C7xx series of PDAs + * + * Copyright (c) 2004-2005 Richard Purdie + * + * Based on Sharp's 2.4 kernel patches + */ +#ifndef __ASM_ARCH_CORGI_H +#define __ASM_ARCH_CORGI_H 1 + +#include "irqs.h" /* PXA_NR_BUILTIN_GPIO */ + +/* + * Corgi (Non Standard) GPIO Definitions + */ +#define CORGI_GPIO_KEY_INT (0) /* Keyboard Interrupt */ +#define CORGI_GPIO_AC_IN (1) /* Charger Detection */ +#define CORGI_GPIO_WAKEUP (3) /* System wakeup notification? */ +#define CORGI_GPIO_AK_INT (4) /* Headphone Jack Control Interrupt */ +#define CORGI_GPIO_TP_INT (5) /* Touch Panel Interrupt */ +#define CORGI_GPIO_nSD_WP (7) /* SD Write Protect? */ +#define CORGI_GPIO_nSD_DETECT (9) /* MMC/SD Card Detect */ +#define CORGI_GPIO_nSD_INT (10) /* SD Interrupt for SDIO? */ +#define CORGI_GPIO_MAIN_BAT_LOW (11) /* Main Battery Low Notification */ +#define CORGI_GPIO_BAT_COVER (11) /* Battery Cover Detect */ +#define CORGI_GPIO_LED_ORANGE (13) /* Orange LED Control */ +#define CORGI_GPIO_CF_CD (14) /* Compact Flash Card Detect */ +#define CORGI_GPIO_CHRG_FULL (16) /* Charging Complete Notification */ +#define CORGI_GPIO_CF_IRQ (17) /* Compact Flash Interrupt */ +#define CORGI_GPIO_LCDCON_CS (19) /* LCD Control Chip Select */ +#define CORGI_GPIO_MAX1111_CS (20) /* MAX1111 Chip Select */ +#define CORGI_GPIO_ADC_TEMP_ON (21) /* Select battery voltage or temperature */ +#define CORGI_GPIO_IR_ON (22) /* Enable IR Transceiver */ +#define CORGI_GPIO_ADS7846_CS (24) /* ADS7846 Chip Select */ +#define CORGI_GPIO_SD_PWR (33) /* MMC/SD Power */ +#define CORGI_GPIO_CHRG_ON (38) /* Enable battery Charging */ +#define CORGI_GPIO_DISCHARGE_ON (42) /* Enable battery Discharge */ +#define CORGI_GPIO_CHRG_UKN (43) /* Unknown Charging (Bypass Control?) */ +#define CORGI_GPIO_HSYNC (44) /* LCD HSync Pulse */ +#define CORGI_GPIO_USB_PULLUP (45) /* USB show presence to host */ + + +/* + * Corgi Keyboard Definitions + */ +#define CORGI_KEY_STROBE_NUM (12) +#define CORGI_KEY_SENSE_NUM (8) +#define CORGI_GPIO_ALL_STROBE_BIT (0x00003ffc) +#define CORGI_GPIO_HIGH_SENSE_BIT (0xfc000000) +#define CORGI_GPIO_HIGH_SENSE_RSHIFT (26) +#define CORGI_GPIO_LOW_SENSE_BIT (0x00000003) +#define CORGI_GPIO_LOW_SENSE_LSHIFT (6) +#define CORGI_GPIO_STROBE_BIT(a) GPIO_bit(66+(a)) +#define CORGI_GPIO_SENSE_BIT(a) GPIO_bit(58+(a)) +#define CORGI_GAFR_ALL_STROBE_BIT (0x0ffffff0) +#define CORGI_GAFR_HIGH_SENSE_BIT (0xfff00000) +#define CORGI_GAFR_LOW_SENSE_BIT (0x0000000f) +#define CORGI_GPIO_KEY_SENSE(a) (58+(a)) +#define CORGI_GPIO_KEY_STROBE(a) (66+(a)) + + +/* + * Corgi Interrupts + */ +#define CORGI_IRQ_GPIO_KEY_INT PXA_GPIO_TO_IRQ(0) +#define CORGI_IRQ_GPIO_AC_IN PXA_GPIO_TO_IRQ(1) +#define CORGI_IRQ_GPIO_WAKEUP PXA_GPIO_TO_IRQ(3) +#define CORGI_IRQ_GPIO_AK_INT PXA_GPIO_TO_IRQ(4) +#define CORGI_IRQ_GPIO_TP_INT PXA_GPIO_TO_IRQ(5) +#define CORGI_IRQ_GPIO_nSD_DETECT PXA_GPIO_TO_IRQ(9) +#define CORGI_IRQ_GPIO_nSD_INT PXA_GPIO_TO_IRQ(10) +#define CORGI_IRQ_GPIO_MAIN_BAT_LOW PXA_GPIO_TO_IRQ(11) +#define CORGI_IRQ_GPIO_CF_CD PXA_GPIO_TO_IRQ(14) +#define CORGI_IRQ_GPIO_CHRG_FULL PXA_GPIO_TO_IRQ(16) /* Battery fully charged */ +#define CORGI_IRQ_GPIO_CF_IRQ PXA_GPIO_TO_IRQ(17) +#define CORGI_IRQ_GPIO_KEY_SENSE(a) PXA_GPIO_TO_IRQ(58+(a)) /* Keyboard Sense lines */ + + +/* + * Corgi SCOOP GPIOs and Config + */ +#define CORGI_SCP_LED_GREEN SCOOP_GPCR_PA11 +#define CORGI_SCP_SWA SCOOP_GPCR_PA12 /* Hinge Switch A */ +#define CORGI_SCP_SWB SCOOP_GPCR_PA13 /* Hinge Switch B */ +#define CORGI_SCP_MUTE_L SCOOP_GPCR_PA14 +#define CORGI_SCP_MUTE_R SCOOP_GPCR_PA15 +#define CORGI_SCP_AKIN_PULLUP SCOOP_GPCR_PA16 +#define CORGI_SCP_APM_ON SCOOP_GPCR_PA17 +#define CORGI_SCP_BACKLIGHT_CONT SCOOP_GPCR_PA18 +#define CORGI_SCP_MIC_BIAS SCOOP_GPCR_PA19 + +#define CORGI_SCOOP_IO_DIR ( CORGI_SCP_LED_GREEN | CORGI_SCP_MUTE_L | CORGI_SCP_MUTE_R | \ + CORGI_SCP_AKIN_PULLUP | CORGI_SCP_APM_ON | CORGI_SCP_BACKLIGHT_CONT | \ + CORGI_SCP_MIC_BIAS ) +#define CORGI_SCOOP_IO_OUT ( CORGI_SCP_MUTE_L | CORGI_SCP_MUTE_R ) + +#define CORGI_SCOOP_GPIO_BASE (PXA_NR_BUILTIN_GPIO) +#define CORGI_GPIO_LED_GREEN (CORGI_SCOOP_GPIO_BASE + 0) +#define CORGI_GPIO_SWA (CORGI_SCOOP_GPIO_BASE + 1) /* Hinge Switch A */ +#define CORGI_GPIO_SWB (CORGI_SCOOP_GPIO_BASE + 2) /* Hinge Switch B */ +#define CORGI_GPIO_MUTE_L (CORGI_SCOOP_GPIO_BASE + 3) +#define CORGI_GPIO_MUTE_R (CORGI_SCOOP_GPIO_BASE + 4) +#define CORGI_GPIO_AKIN_PULLUP (CORGI_SCOOP_GPIO_BASE + 5) +#define CORGI_GPIO_APM_ON (CORGI_SCOOP_GPIO_BASE + 6) +#define CORGI_GPIO_BACKLIGHT_CONT (CORGI_SCOOP_GPIO_BASE + 7) +#define CORGI_GPIO_MIC_BIAS (CORGI_SCOOP_GPIO_BASE + 8) + +#endif /* __ASM_ARCH_CORGI_H */ + diff --git a/arch/arm/mach-pxa/include/mach/dma.h b/arch/arm/mach-pxa/include/mach/dma.h new file mode 100644 index 000000000..79f9842a7 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/dma.h @@ -0,0 +1,17 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ +/* + * arch/arm/mach-pxa/include/mach/dma.h + * + * Author: Nicolas Pitre + * Created: Jun 15, 2001 + * Copyright: MontaVista Software, Inc. + */ +#ifndef __ASM_ARCH_DMA_H +#define __ASM_ARCH_DMA_H + +#include <mach/hardware.h> + +/* DMA Controller Registers Definitions */ +#define DMAC_REGS_VIRT io_p2v(0x40000000) + +#endif /* _ASM_ARCH_DMA_H */ diff --git a/arch/arm/mach-pxa/include/mach/eseries-gpio.h b/arch/arm/mach-pxa/include/mach/eseries-gpio.h new file mode 100644 index 000000000..5c645600d --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/eseries-gpio.h @@ -0,0 +1,63 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ +/* + * eseries-gpio.h + * + * Copyright (C) Ian Molton <spyro@f2s.com> + */ + +/* e-series power button */ +#define GPIO_ESERIES_POWERBTN 0 + +/* UDC GPIO definitions */ +#define GPIO_E7XX_USB_DISC 13 +#define GPIO_E7XX_USB_PULLUP 3 + +#define GPIO_E800_USB_DISC 4 +#define GPIO_E800_USB_PULLUP 84 + +/* e740 PCMCIA GPIO definitions */ +/* Note: PWR1 seems to be inverted */ +#define GPIO_E740_PCMCIA_CD0 8 +#define GPIO_E740_PCMCIA_CD1 44 +#define GPIO_E740_PCMCIA_RDY0 11 +#define GPIO_E740_PCMCIA_RDY1 6 +#define GPIO_E740_PCMCIA_RST0 27 +#define GPIO_E740_PCMCIA_RST1 24 +#define GPIO_E740_PCMCIA_PWR0 20 +#define GPIO_E740_PCMCIA_PWR1 23 + +/* e750 PCMCIA GPIO definitions */ +#define GPIO_E750_PCMCIA_CD0 8 +#define GPIO_E750_PCMCIA_RDY0 12 +#define GPIO_E750_PCMCIA_RST0 27 +#define GPIO_E750_PCMCIA_PWR0 20 + +/* e800 PCMCIA GPIO definitions */ +#define GPIO_E800_PCMCIA_RST0 69 +#define GPIO_E800_PCMCIA_RST1 72 +#define GPIO_E800_PCMCIA_PWR0 20 +#define GPIO_E800_PCMCIA_PWR1 73 + +/* e7xx IrDA power control */ +#define GPIO_E7XX_IR_OFF 38 + +/* e740 audio control GPIOs */ +#define GPIO_E740_WM9705_nAVDD2 16 +#define GPIO_E740_MIC_ON 40 +#define GPIO_E740_AMP_ON 41 + +/* e750 audio control GPIOs */ +#define GPIO_E750_HP_AMP_OFF 4 +#define GPIO_E750_SPK_AMP_OFF 7 +#define GPIO_E750_HP_DETECT 37 + +/* e800 audio control GPIOs */ +#define GPIO_E800_HP_DETECT 81 +#define GPIO_E800_HP_AMP_OFF 82 +#define GPIO_E800_SPK_AMP_ON 83 + +/* ASIC related GPIOs */ +#define GPIO_ESERIES_TMIO_IRQ 5 +#define GPIO_ESERIES_TMIO_PCLR 19 +#define GPIO_ESERIES_TMIO_SUSPEND 45 +#define GPIO_E800_ANGELX_IRQ 8 diff --git a/arch/arm/mach-pxa/include/mach/generic.h b/arch/arm/mach-pxa/include/mach/generic.h new file mode 100644 index 000000000..665542e0c --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/generic.h @@ -0,0 +1 @@ +#include "../../generic.h" diff --git a/arch/arm/mach-pxa/include/mach/hardware.h b/arch/arm/mach-pxa/include/mach/hardware.h new file mode 100644 index 000000000..ee7eab161 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/hardware.h @@ -0,0 +1,305 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ +/* + * arch/arm/mach-pxa/include/mach/hardware.h + * + * Author: Nicolas Pitre + * Created: Jun 15, 2001 + * Copyright: MontaVista Software Inc. + */ + +#ifndef __ASM_ARCH_HARDWARE_H +#define __ASM_ARCH_HARDWARE_H + +#include <mach/addr-map.h> + +/* + * Workarounds for at least 2 errata so far require this. + * The mapping is set in mach-pxa/generic.c. + */ +#define UNCACHED_PHYS_0 0xfe000000 +#define UNCACHED_PHYS_0_SIZE 0x00100000 + +/* + * Intel PXA2xx internal register mapping: + * + * 0x40000000 - 0x41ffffff <--> 0xf2000000 - 0xf3ffffff + * 0x44000000 - 0x45ffffff <--> 0xf4000000 - 0xf5ffffff + * 0x48000000 - 0x49ffffff <--> 0xf6000000 - 0xf7ffffff + * 0x4c000000 - 0x4dffffff <--> 0xf8000000 - 0xf9ffffff + * 0x50000000 - 0x51ffffff <--> 0xfa000000 - 0xfbffffff + * 0x54000000 - 0x55ffffff <--> 0xfc000000 - 0xfdffffff + * 0x58000000 - 0x59ffffff <--> 0xfe000000 - 0xffffffff + * + * Note that not all PXA2xx chips implement all those addresses, and the + * kernel only maps the minimum needed range of this mapping. + */ +#define io_v2p(x) (0x3c000000 + ((x) & 0x01ffffff) + (((x) & 0x0e000000) << 1)) +#define io_p2v(x) IOMEM(0xf2000000 + ((x) & 0x01ffffff) + (((x) & 0x1c000000) >> 1)) + +#ifndef __ASSEMBLY__ +# define __REG(x) (*((volatile u32 __iomem *)io_p2v(x))) + +/* With indexed regs we don't want to feed the index through io_p2v() + especially if it is a variable, otherwise horrible code will result. */ +# define __REG2(x,y) \ + (*(volatile u32 __iomem*)((u32)&__REG(x) + (y))) + +# define __PREG(x) (io_v2p((u32)&(x))) + +#else + +# define __REG(x) io_p2v(x) +# define __PREG(x) io_v2p(x) + +#endif + +#ifndef __ASSEMBLY__ + +#include <asm/cputype.h> + +/* + * CPU Stepping CPU_ID JTAG_ID + * + * PXA210 B0 0x69052922 0x2926C013 + * PXA210 B1 0x69052923 0x3926C013 + * PXA210 B2 0x69052924 0x4926C013 + * PXA210 C0 0x69052D25 0x5926C013 + * + * PXA250 A0 0x69052100 0x09264013 + * PXA250 A1 0x69052101 0x19264013 + * PXA250 B0 0x69052902 0x29264013 + * PXA250 B1 0x69052903 0x39264013 + * PXA250 B2 0x69052904 0x49264013 + * PXA250 C0 0x69052D05 0x59264013 + * + * PXA255 A0 0x69052D06 0x69264013 + * + * PXA26x A0 0x69052903 0x39264013 + * PXA26x B0 0x69052D05 0x59264013 + * + * PXA27x A0 0x69054110 0x09265013 + * PXA27x A1 0x69054111 0x19265013 + * PXA27x B0 0x69054112 0x29265013 + * PXA27x B1 0x69054113 0x39265013 + * PXA27x C0 0x69054114 0x49265013 + * PXA27x C5 0x69054117 0x79265013 + * + * PXA30x A0 0x69056880 0x0E648013 + * PXA30x A1 0x69056881 0x1E648013 + * PXA31x A0 0x69056890 0x0E649013 + * PXA31x A1 0x69056891 0x1E649013 + * PXA31x A2 0x69056892 0x2E649013 + * PXA32x B1 0x69056825 0x5E642013 + * PXA32x B2 0x69056826 0x6E642013 + * + * PXA930 B0 0x69056835 0x5E643013 + * PXA930 B1 0x69056837 0x7E643013 + * PXA930 B2 0x69056838 0x8E643013 + * + * PXA935 A0 0x56056931 0x1E653013 + * PXA935 B0 0x56056936 0x6E653013 + * PXA935 B1 0x56056938 0x8E653013 + */ +#ifdef CONFIG_PXA25x +#define __cpu_is_pxa210(id) \ + ({ \ + unsigned int _id = (id) & 0xf3f0; \ + _id == 0x2120; \ + }) + +#define __cpu_is_pxa250(id) \ + ({ \ + unsigned int _id = (id) & 0xf3ff; \ + _id <= 0x2105; \ + }) + +#define __cpu_is_pxa255(id) \ + ({ \ + unsigned int _id = (id) & 0xffff; \ + _id == 0x2d06; \ + }) + +#define __cpu_is_pxa25x(id) \ + ({ \ + unsigned int _id = (id) & 0xf300; \ + _id == 0x2100; \ + }) +#else +#define __cpu_is_pxa210(id) (0) +#define __cpu_is_pxa250(id) (0) +#define __cpu_is_pxa255(id) (0) +#define __cpu_is_pxa25x(id) (0) +#endif + +#ifdef CONFIG_PXA27x +#define __cpu_is_pxa27x(id) \ + ({ \ + unsigned int _id = (id) >> 4 & 0xfff; \ + _id == 0x411; \ + }) +#else +#define __cpu_is_pxa27x(id) (0) +#endif + +#ifdef CONFIG_CPU_PXA300 +#define __cpu_is_pxa300(id) \ + ({ \ + unsigned int _id = (id) >> 4 & 0xfff; \ + _id == 0x688; \ + }) +#else +#define __cpu_is_pxa300(id) (0) +#endif + +#ifdef CONFIG_CPU_PXA310 +#define __cpu_is_pxa310(id) \ + ({ \ + unsigned int _id = (id) >> 4 & 0xfff; \ + _id == 0x689; \ + }) +#else +#define __cpu_is_pxa310(id) (0) +#endif + +#ifdef CONFIG_CPU_PXA320 +#define __cpu_is_pxa320(id) \ + ({ \ + unsigned int _id = (id) >> 4 & 0xfff; \ + _id == 0x603 || _id == 0x682; \ + }) +#else +#define __cpu_is_pxa320(id) (0) +#endif + +#ifdef CONFIG_CPU_PXA930 +#define __cpu_is_pxa930(id) \ + ({ \ + unsigned int _id = (id) >> 4 & 0xfff; \ + _id == 0x683; \ + }) +#else +#define __cpu_is_pxa930(id) (0) +#endif + +#ifdef CONFIG_CPU_PXA935 +#define __cpu_is_pxa935(id) \ + ({ \ + unsigned int _id = (id) >> 4 & 0xfff; \ + _id == 0x693; \ + }) +#else +#define __cpu_is_pxa935(id) (0) +#endif + +#define cpu_is_pxa210() \ + ({ \ + __cpu_is_pxa210(read_cpuid_id()); \ + }) + +#define cpu_is_pxa250() \ + ({ \ + __cpu_is_pxa250(read_cpuid_id()); \ + }) + +#define cpu_is_pxa255() \ + ({ \ + __cpu_is_pxa255(read_cpuid_id()); \ + }) + +#define cpu_is_pxa25x() \ + ({ \ + __cpu_is_pxa25x(read_cpuid_id()); \ + }) + +#define cpu_is_pxa27x() \ + ({ \ + __cpu_is_pxa27x(read_cpuid_id()); \ + }) + +#define cpu_is_pxa300() \ + ({ \ + __cpu_is_pxa300(read_cpuid_id()); \ + }) + +#define cpu_is_pxa310() \ + ({ \ + __cpu_is_pxa310(read_cpuid_id()); \ + }) + +#define cpu_is_pxa320() \ + ({ \ + __cpu_is_pxa320(read_cpuid_id()); \ + }) + +#define cpu_is_pxa930() \ + ({ \ + __cpu_is_pxa930(read_cpuid_id()); \ + }) + +#define cpu_is_pxa935() \ + ({ \ + __cpu_is_pxa935(read_cpuid_id()); \ + }) + + + +/* + * CPUID Core Generation Bit + * <= 0x2 for pxa21x/pxa25x/pxa26x/pxa27x + */ +#if defined(CONFIG_PXA25x) || defined(CONFIG_PXA27x) +#define __cpu_is_pxa2xx(id) \ + ({ \ + unsigned int _id = (id) >> 13 & 0x7; \ + _id <= 0x2; \ + }) +#else +#define __cpu_is_pxa2xx(id) (0) +#endif + +#ifdef CONFIG_PXA3xx +#define __cpu_is_pxa3xx(id) \ + ({ \ + __cpu_is_pxa300(id) \ + || __cpu_is_pxa310(id) \ + || __cpu_is_pxa320(id) \ + || __cpu_is_pxa93x(id); \ + }) +#else +#define __cpu_is_pxa3xx(id) (0) +#endif + +#if defined(CONFIG_CPU_PXA930) || defined(CONFIG_CPU_PXA935) +#define __cpu_is_pxa93x(id) \ + ({ \ + __cpu_is_pxa930(id) \ + || __cpu_is_pxa935(id); \ + }) +#else +#define __cpu_is_pxa93x(id) (0) +#endif + +#define cpu_is_pxa2xx() \ + ({ \ + __cpu_is_pxa2xx(read_cpuid_id()); \ + }) + +#define cpu_is_pxa3xx() \ + ({ \ + __cpu_is_pxa3xx(read_cpuid_id()); \ + }) + +#define cpu_is_pxa93x() \ + ({ \ + __cpu_is_pxa93x(read_cpuid_id()); \ + }) + + +/* + * return current memory and LCD clock frequency in units of 10kHz + */ +extern unsigned int get_memclk_frequency_10khz(void); + +#endif + +#endif /* _ASM_ARCH_HARDWARE_H */ diff --git a/arch/arm/mach-pxa/include/mach/hx4700.h b/arch/arm/mach-pxa/include/mach/hx4700.h new file mode 100644 index 000000000..0c30e6d9c --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/hx4700.h @@ -0,0 +1,129 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ +/* + * GPIO and IRQ definitions for HP iPAQ hx4700 + * + * Copyright (c) 2008 Philipp Zabel + */ + +#ifndef _HX4700_H_ +#define _HX4700_H_ + +#include <linux/gpio.h> +#include <linux/mfd/asic3.h> +#include "irqs.h" /* PXA_NR_BUILTIN_GPIO */ + +#define HX4700_ASIC3_GPIO_BASE PXA_NR_BUILTIN_GPIO +#define HX4700_EGPIO_BASE (HX4700_ASIC3_GPIO_BASE + ASIC3_NUM_GPIOS) +#define HX4700_NR_IRQS (IRQ_BOARD_START + 70) + +/* + * PXA GPIOs + */ + +#define GPIO0_HX4700_nKEY_POWER 0 +#define GPIO12_HX4700_ASIC3_IRQ 12 +#define GPIO13_HX4700_W3220_IRQ 13 +#define GPIO14_HX4700_nWLAN_IRQ 14 +#define GPIO18_HX4700_RDY 18 +#define GPIO22_HX4700_LCD_RL 22 +#define GPIO27_HX4700_CODEC_ON 27 +#define GPIO32_HX4700_RS232_ON 32 +#define GPIO52_HX4700_CPU_nBATT_FAULT 52 +#define GPIO58_HX4700_TSC2046_nPENIRQ 58 +#define GPIO59_HX4700_LCD_PC1 59 +#define GPIO60_HX4700_CF_RNB 60 +#define GPIO61_HX4700_W3220_nRESET 61 +#define GPIO62_HX4700_LCD_nRESET 62 +#define GPIO63_HX4700_CPU_SS_nRESET 63 +#define GPIO65_HX4700_TSC2046_PEN_PU 65 +#define GPIO66_HX4700_ASIC3_nSDIO_IRQ 66 +#define GPIO67_HX4700_EUART_PS 67 +#define GPIO70_HX4700_LCD_SLIN1 70 +#define GPIO71_HX4700_ASIC3_nRESET 71 +#define GPIO72_HX4700_BQ24022_nCHARGE_EN 72 +#define GPIO73_HX4700_LCD_UD_1 73 +#define GPIO75_HX4700_EARPHONE_nDET 75 +#define GPIO76_HX4700_USBC_PUEN 76 +#define GPIO81_HX4700_CPU_GP_nRESET 81 +#define GPIO82_HX4700_EUART_RESET 82 +#define GPIO83_HX4700_WLAN_nRESET 83 +#define GPIO84_HX4700_LCD_SQN 84 +#define GPIO85_HX4700_nPCE1 85 +#define GPIO88_HX4700_TSC2046_CS 88 +#define GPIO91_HX4700_FLASH_VPEN 91 +#define GPIO92_HX4700_HP_DRIVER 92 +#define GPIO93_HX4700_EUART_INT 93 +#define GPIO94_HX4700_KEY_MAIL 94 +#define GPIO95_HX4700_BATT_OFF 95 +#define GPIO96_HX4700_BQ24022_ISET2 96 +#define GPIO97_HX4700_nBL_DETECT 97 +#define GPIO99_HX4700_KEY_CONTACTS 99 +#define GPIO100_HX4700_AUTO_SENSE 100 /* BL auto brightness */ +#define GPIO102_HX4700_SYNAPTICS_POWER_ON 102 +#define GPIO103_HX4700_SYNAPTICS_INT 103 +#define GPIO105_HX4700_nIR_ON 105 +#define GPIO106_HX4700_CPU_BT_nRESET 106 +#define GPIO107_HX4700_SPK_nSD 107 +#define GPIO109_HX4700_CODEC_nPDN 109 +#define GPIO110_HX4700_LCD_LVDD_3V3_ON 110 +#define GPIO111_HX4700_LCD_AVDD_3V3_ON 111 +#define GPIO112_HX4700_LCD_N2V7_7V3_ON 112 +#define GPIO114_HX4700_CF_RESET 114 +#define GPIO116_HX4700_CPU_HW_nRESET 116 + +/* + * ASIC3 GPIOs + */ + +#define GPIOC_BASE (HX4700_ASIC3_GPIO_BASE + 32) +#define GPIOD_BASE (HX4700_ASIC3_GPIO_BASE + 48) + +#define GPIOC0_LED_RED (GPIOC_BASE + 0) +#define GPIOC1_LED_GREEN (GPIOC_BASE + 1) +#define GPIOC2_LED_BLUE (GPIOC_BASE + 2) +#define GPIOC3_nSD_CS (GPIOC_BASE + 3) +#define GPIOC4_CF_nCD (GPIOC_BASE + 4) /* Input */ +#define GPIOC5_nCIOW (GPIOC_BASE + 5) /* Output, to CF */ +#define GPIOC6_nCIOR (GPIOC_BASE + 6) /* Output, to CF */ +#define GPIOC7_nPCE1 (GPIOC_BASE + 7) /* Input, from CPU */ +#define GPIOC8_nPCE2 (GPIOC_BASE + 8) /* Input, from CPU */ +#define GPIOC9_nPOE (GPIOC_BASE + 9) /* Input, from CPU */ +#define GPIOC10_CF_nPWE (GPIOC_BASE + 10) /* Input */ +#define GPIOC11_PSKTSEL (GPIOC_BASE + 11) /* Input, from CPU */ +#define GPIOC12_nPREG (GPIOC_BASE + 12) /* Input, from CPU */ +#define GPIOC13_nPWAIT (GPIOC_BASE + 13) /* Output, to CPU */ +#define GPIOC14_nPIOIS16 (GPIOC_BASE + 14) /* Output, to CPU */ +#define GPIOC15_nPIOR (GPIOC_BASE + 15) /* Input, from CPU */ + +#define GPIOD0_CPU_SS_INT (GPIOD_BASE + 0) /* Input */ +#define GPIOD1_nKEY_CALENDAR (GPIOD_BASE + 1) +#define GPIOD2_BLUETOOTH_WAKEUP (GPIOD_BASE + 2) +#define GPIOD3_nKEY_HOME (GPIOD_BASE + 3) +#define GPIOD4_CF_nCD (GPIOD_BASE + 4) /* Input, from CF */ +#define GPIOD5_nPIO (GPIOD_BASE + 5) /* Input */ +#define GPIOD6_nKEY_RECORD (GPIOD_BASE + 6) +#define GPIOD7_nSDIO_DETECT (GPIOD_BASE + 7) +#define GPIOD8_COM_DCD (GPIOD_BASE + 8) /* Input */ +#define GPIOD9_nAC_IN (GPIOD_BASE + 9) +#define GPIOD10_nSDIO_IRQ (GPIOD_BASE + 10) /* Input */ +#define GPIOD11_nCIOIS16 (GPIOD_BASE + 11) /* Input, from CF */ +#define GPIOD12_nCWAIT (GPIOD_BASE + 12) /* Input, from CF */ +#define GPIOD13_CF_RNB (GPIOD_BASE + 13) /* Input */ +#define GPIOD14_nUSBC_DETECT (GPIOD_BASE + 14) +#define GPIOD15_nPIOW (GPIOD_BASE + 15) /* Input, from CPU */ + +/* + * EGPIOs + */ + +#define EGPIO0_VCC_3V3_EN (HX4700_EGPIO_BASE + 0) /* WLAN support chip */ +#define EGPIO1_WL_VREG_EN (HX4700_EGPIO_BASE + 1) /* WLAN power */ +#define EGPIO2_VCC_2V1_WL_EN (HX4700_EGPIO_BASE + 2) /* unused */ +#define EGPIO3_SS_PWR_ON (HX4700_EGPIO_BASE + 3) /* smart slot power */ +#define EGPIO4_CF_3V3_ON (HX4700_EGPIO_BASE + 4) /* CF 3.3V enable */ +#define EGPIO5_BT_3V3_ON (HX4700_EGPIO_BASE + 5) /* BT 3.3V enable */ +#define EGPIO6_WL1V8_EN (HX4700_EGPIO_BASE + 6) /* WLAN 1.8V enable */ +#define EGPIO7_VCC_3V3_WL_EN (HX4700_EGPIO_BASE + 7) /* WLAN 3.3V enable */ +#define EGPIO8_USB_3V3_ON (HX4700_EGPIO_BASE + 8) /* unused */ + +#endif /* _HX4700_H_ */ diff --git a/arch/arm/mach-pxa/include/mach/irqs.h b/arch/arm/mach-pxa/include/mach/irqs.h new file mode 100644 index 000000000..22bf536a4 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/irqs.h @@ -0,0 +1,109 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ +/* + * arch/arm/mach-pxa/include/mach/irqs.h + * + * Author: Nicolas Pitre + * Created: Jun 15, 2001 + * Copyright: MontaVista Software Inc. + */ +#ifndef __ASM_MACH_IRQS_H +#define __ASM_MACH_IRQS_H + +#include <asm/irq.h> + +#define PXA_ISA_IRQ(x) (x) +#define PXA_IRQ(x) (NR_IRQS_LEGACY + (x)) + +#define IRQ_SSP3 PXA_IRQ(0) /* SSP3 service request */ +#define IRQ_MSL PXA_IRQ(1) /* MSL Interface interrupt */ +#define IRQ_USBH2 PXA_IRQ(2) /* USB Host interrupt 1 (OHCI,PXA27x) */ +#define IRQ_USBH1 PXA_IRQ(3) /* USB Host interrupt 2 (non-OHCI,PXA27x) */ +#define IRQ_KEYPAD PXA_IRQ(4) /* Key pad controller */ +#define IRQ_MEMSTK PXA_IRQ(5) /* Memory Stick interrupt (PXA27x) */ +#define IRQ_ACIPC0 PXA_IRQ(5) /* AP-CP Communication (PXA930) */ +#define IRQ_PWRI2C PXA_IRQ(6) /* Power I2C interrupt */ +#define IRQ_HWUART PXA_IRQ(7) /* HWUART Transmit/Receive/Error (PXA26x) */ +#define IRQ_OST_4_11 PXA_IRQ(7) /* OS timer 4-11 matches (PXA27x) */ +#define IRQ_GPIO0 PXA_IRQ(8) /* GPIO0 Edge Detect */ +#define IRQ_GPIO1 PXA_IRQ(9) /* GPIO1 Edge Detect */ +#define IRQ_GPIO_2_x PXA_IRQ(10) /* GPIO[2-x] Edge Detect */ +#define IRQ_USB PXA_IRQ(11) /* USB Service */ +#define IRQ_PMU PXA_IRQ(12) /* Performance Monitoring Unit */ +#define IRQ_I2S PXA_IRQ(13) /* I2S Interrupt (PXA27x) */ +#define IRQ_SSP4 PXA_IRQ(13) /* SSP4 service request (PXA3xx) */ +#define IRQ_AC97 PXA_IRQ(14) /* AC97 Interrupt */ +#define IRQ_ASSP PXA_IRQ(15) /* Audio SSP Service Request (PXA25x) */ +#define IRQ_USIM PXA_IRQ(15) /* Smart Card interface interrupt (PXA27x) */ +#define IRQ_NSSP PXA_IRQ(16) /* Network SSP Service Request (PXA25x) */ +#define IRQ_SSP2 PXA_IRQ(16) /* SSP2 interrupt (PXA27x) */ +#define IRQ_LCD PXA_IRQ(17) /* LCD Controller Service Request */ +#define IRQ_I2C PXA_IRQ(18) /* I2C Service Request */ +#define IRQ_ICP PXA_IRQ(19) /* ICP Transmit/Receive/Error */ +#define IRQ_ACIPC2 PXA_IRQ(19) /* AP-CP Communication (PXA930) */ +#define IRQ_STUART PXA_IRQ(20) /* STUART Transmit/Receive/Error */ +#define IRQ_BTUART PXA_IRQ(21) /* BTUART Transmit/Receive/Error */ +#define IRQ_FFUART PXA_IRQ(22) /* FFUART Transmit/Receive/Error*/ +#define IRQ_MMC PXA_IRQ(23) /* MMC Status/Error Detection */ +#define IRQ_SSP PXA_IRQ(24) /* SSP Service Request */ +#define IRQ_DMA PXA_IRQ(25) /* DMA Channel Service Request */ +#define IRQ_OST0 PXA_IRQ(26) /* OS Timer match 0 */ +#define IRQ_OST1 PXA_IRQ(27) /* OS Timer match 1 */ +#define IRQ_OST2 PXA_IRQ(28) /* OS Timer match 2 */ +#define IRQ_OST3 PXA_IRQ(29) /* OS Timer match 3 */ +#define IRQ_RTC1Hz PXA_IRQ(30) /* RTC HZ Clock Tick */ +#define IRQ_RTCAlrm PXA_IRQ(31) /* RTC Alarm */ + +#define IRQ_TPM PXA_IRQ(32) /* TPM interrupt */ +#define IRQ_CAMERA PXA_IRQ(33) /* Camera Interface */ +#define IRQ_CIR PXA_IRQ(34) /* Consumer IR */ +#define IRQ_COMM_WDT PXA_IRQ(35) /* Comm WDT interrupt */ +#define IRQ_TSI PXA_IRQ(36) /* Touch Screen Interface (PXA320) */ +#define IRQ_ENHROT PXA_IRQ(37) /* Enhanced Rotary (PXA930) */ +#define IRQ_USIM2 PXA_IRQ(38) /* USIM2 Controller */ +#define IRQ_GCU PXA_IRQ(39) /* Graphics Controller (PXA3xx) */ +#define IRQ_ACIPC1 PXA_IRQ(40) /* AP-CP Communication (PXA930) */ +#define IRQ_MMC2 PXA_IRQ(41) /* MMC2 Controller */ +#define IRQ_TRKBALL PXA_IRQ(43) /* Track Ball (PXA930) */ +#define IRQ_1WIRE PXA_IRQ(44) /* 1-Wire Controller */ +#define IRQ_NAND PXA_IRQ(45) /* NAND Controller */ +#define IRQ_USB2 PXA_IRQ(46) /* USB 2.0 Device Controller */ +#define IRQ_WAKEUP0 PXA_IRQ(49) /* EXT_WAKEUP0 */ +#define IRQ_WAKEUP1 PXA_IRQ(50) /* EXT_WAKEUP1 */ +#define IRQ_DMEMC PXA_IRQ(51) /* Dynamic Memory Controller */ +#define IRQ_MMC3 PXA_IRQ(55) /* MMC3 Controller (PXA310) */ + +#define IRQ_U2O PXA_IRQ(64) /* USB OTG 2.0 Controller (PXA935) */ +#define IRQ_U2H PXA_IRQ(65) /* USB Host 2.0 Controller (PXA935) */ +#define IRQ_PXA935_MMC0 PXA_IRQ(72) /* MMC0 Controller (PXA935) */ +#define IRQ_PXA935_MMC1 PXA_IRQ(73) /* MMC1 Controller (PXA935) */ +#define IRQ_PXA935_MMC2 PXA_IRQ(74) /* MMC2 Controller (PXA935) */ +#define IRQ_U2P PXA_IRQ(93) /* USB PHY D+/D- Lines (PXA935) */ + +#define PXA_GPIO_IRQ_BASE PXA_IRQ(96) +#define PXA_NR_BUILTIN_GPIO (192) +#define PXA_GPIO_TO_IRQ(x) (PXA_GPIO_IRQ_BASE + (x)) + +/* + * The following interrupts are for board specific purposes. Since + * the kernel can only run on one machine at a time, we can re-use + * these. + * By default, no board IRQ is reserved. It should be finished in + * custom board since sparse IRQ is already enabled. + */ +#define IRQ_BOARD_START (PXA_GPIO_IRQ_BASE + PXA_NR_BUILTIN_GPIO) + +#define PXA_NR_IRQS (IRQ_BOARD_START) + +#ifndef __ASSEMBLY__ +struct irq_data; +struct pt_regs; + +void pxa_mask_irq(struct irq_data *); +void pxa_unmask_irq(struct irq_data *); +void icip_handle_irq(struct pt_regs *); +void ichp_handle_irq(struct pt_regs *); + +void pxa_init_irq(int irq_nr, int (*set_wake)(struct irq_data *, unsigned int)); +#endif + +#endif /* __ASM_MACH_IRQS_H */ diff --git a/arch/arm/mach-pxa/include/mach/lubbock.h b/arch/arm/mach-pxa/include/mach/lubbock.h new file mode 100644 index 000000000..a3af4a2f9 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/lubbock.h @@ -0,0 +1,49 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ +/* + * arch/arm/mach-pxa/include/mach/lubbock.h + * + * Author: Nicolas Pitre + * Created: Jun 15, 2001 + * Copyright: MontaVista Software Inc. + */ + +#include <mach/irqs.h> + +#define LUBBOCK_ETH_PHYS PXA_CS3_PHYS + +#define LUBBOCK_FPGA_PHYS PXA_CS2_PHYS +#define LUBBOCK_FPGA_VIRT (0xf0000000) +#define LUB_P2V(x) ((x) - LUBBOCK_FPGA_PHYS + LUBBOCK_FPGA_VIRT) +#define LUB_V2P(x) ((x) - LUBBOCK_FPGA_VIRT + LUBBOCK_FPGA_PHYS) + +#ifndef __ASSEMBLY__ +# define __LUB_REG(x) (*((volatile unsigned long *)LUB_P2V(x))) +#else +# define __LUB_REG(x) LUB_P2V(x) +#endif + +/* FPGA register virtual addresses */ +#define LUB_WHOAMI __LUB_REG(LUBBOCK_FPGA_PHYS + 0x000) +#define LUB_DISC_BLNK_LED __LUB_REG(LUBBOCK_FPGA_PHYS + 0x040) +#define LUB_CONF_SWITCHES __LUB_REG(LUBBOCK_FPGA_PHYS + 0x050) +#define LUB_USER_SWITCHES __LUB_REG(LUBBOCK_FPGA_PHYS + 0x060) +#define LUB_MISC_WR __LUB_REG(LUBBOCK_FPGA_PHYS + 0x080) +#define LUB_MISC_RD __LUB_REG(LUBBOCK_FPGA_PHYS + 0x090) +#define LUB_IRQ_MASK_EN __LUB_REG(LUBBOCK_FPGA_PHYS + 0x0c0) +#define LUB_IRQ_SET_CLR __LUB_REG(LUBBOCK_FPGA_PHYS + 0x0d0) +#define LUB_GP __LUB_REG(LUBBOCK_FPGA_PHYS + 0x100) + +/* Board specific IRQs */ +#define LUBBOCK_NR_IRQS IRQ_BOARD_START + +#define LUBBOCK_IRQ(x) (LUBBOCK_NR_IRQS + (x)) +#define LUBBOCK_SD_IRQ LUBBOCK_IRQ(0) +#define LUBBOCK_SA1111_IRQ LUBBOCK_IRQ(1) +#define LUBBOCK_USB_IRQ LUBBOCK_IRQ(2) /* usb connect */ +#define LUBBOCK_ETH_IRQ LUBBOCK_IRQ(3) +#define LUBBOCK_UCB1400_IRQ LUBBOCK_IRQ(4) +#define LUBBOCK_BB_IRQ LUBBOCK_IRQ(5) +#define LUBBOCK_USB_DISC_IRQ LUBBOCK_IRQ(6) /* usb disconnect */ +#define LUBBOCK_LAST_IRQ LUBBOCK_IRQ(6) + +#define LUBBOCK_SA1111_IRQ_BASE (LUBBOCK_NR_IRQS + 32) diff --git a/arch/arm/mach-pxa/include/mach/magician.h b/arch/arm/mach-pxa/include/mach/magician.h new file mode 100644 index 000000000..7d3af561a --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/magician.h @@ -0,0 +1,125 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ +/* + * GPIO and IRQ definitions for HTC Magician PDA phones + * + * Copyright (c) 2007 Philipp Zabel + */ + +#ifndef _MAGICIAN_H_ +#define _MAGICIAN_H_ + +#include <linux/gpio.h> +#include <mach/irqs.h> + +/* + * PXA GPIOs + */ + +#define GPIO0_MAGICIAN_KEY_POWER 0 +#define GPIO9_MAGICIAN_UNKNOWN 9 +#define GPIO10_MAGICIAN_GSM_IRQ 10 +#define GPIO11_MAGICIAN_GSM_OUT1 11 +#define GPIO13_MAGICIAN_CPLD_IRQ 13 +#define GPIO14_MAGICIAN_TSC2046_CS 14 +#define GPIO18_MAGICIAN_UNKNOWN 18 +#define GPIO22_MAGICIAN_VIBRA_EN 22 +#define GPIO26_MAGICIAN_GSM_POWER 26 +#define GPIO27_MAGICIAN_USBC_PUEN 27 +#define GPIO30_MAGICIAN_BQ24022_nCHARGE_EN 30 +#define GPIO37_MAGICIAN_KEY_HANGUP 37 +#define GPIO38_MAGICIAN_KEY_CONTACTS 38 +#define GPIO40_MAGICIAN_GSM_OUT2 40 +#define GPIO48_MAGICIAN_UNKNOWN 48 +#define GPIO56_MAGICIAN_UNKNOWN 56 +#define GPIO57_MAGICIAN_CAM_RESET 57 +#define GPIO75_MAGICIAN_SAMSUNG_POWER 75 +#define GPIO83_MAGICIAN_nIR_EN 83 +#define GPIO86_MAGICIAN_GSM_RESET 86 +#define GPIO87_MAGICIAN_GSM_SELECT 87 +#define GPIO90_MAGICIAN_KEY_CALENDAR 90 +#define GPIO91_MAGICIAN_KEY_CAMERA 91 +#define GPIO93_MAGICIAN_KEY_UP 93 +#define GPIO94_MAGICIAN_KEY_DOWN 94 +#define GPIO95_MAGICIAN_KEY_LEFT 95 +#define GPIO96_MAGICIAN_KEY_RIGHT 96 +#define GPIO97_MAGICIAN_KEY_ENTER 97 +#define GPIO98_MAGICIAN_KEY_RECORD 98 +#define GPIO99_MAGICIAN_HEADPHONE_IN 99 +#define GPIO100_MAGICIAN_KEY_VOL_UP 100 +#define GPIO101_MAGICIAN_KEY_VOL_DOWN 101 +#define GPIO102_MAGICIAN_KEY_PHONE 102 +#define GPIO103_MAGICIAN_LED_KP 103 +#define GPIO104_MAGICIAN_LCD_VOFF_EN 104 +#define GPIO105_MAGICIAN_LCD_VON_EN 105 +#define GPIO106_MAGICIAN_LCD_DCDC_NRESET 106 +#define GPIO107_MAGICIAN_DS1WM_IRQ 107 +#define GPIO108_MAGICIAN_GSM_READY 108 +#define GPIO114_MAGICIAN_UNKNOWN 114 +#define GPIO115_MAGICIAN_nPEN_IRQ 115 +#define GPIO116_MAGICIAN_nCAM_EN 116 +#define GPIO119_MAGICIAN_UNKNOWN 119 +#define GPIO120_MAGICIAN_UNKNOWN 120 + +/* + * CPLD IRQs + */ + +#define IRQ_MAGICIAN_SD (IRQ_BOARD_START + 0) +#define IRQ_MAGICIAN_EP (IRQ_BOARD_START + 1) +#define IRQ_MAGICIAN_BT (IRQ_BOARD_START + 2) +#define IRQ_MAGICIAN_VBUS (IRQ_BOARD_START + 3) + +#define MAGICIAN_NR_IRQS (IRQ_BOARD_START + 8) + +/* + * CPLD EGPIOs + */ + +#define MAGICIAN_EGPIO_BASE PXA_NR_BUILTIN_GPIO +#define MAGICIAN_EGPIO(reg,bit) \ + (MAGICIAN_EGPIO_BASE + 8*reg + bit) + +/* output */ + +#define EGPIO_MAGICIAN_TOPPOLY_POWER MAGICIAN_EGPIO(0, 2) +#define EGPIO_MAGICIAN_LED_POWER MAGICIAN_EGPIO(0, 5) +#define EGPIO_MAGICIAN_GSM_RESET MAGICIAN_EGPIO(0, 6) +#define EGPIO_MAGICIAN_LCD_POWER MAGICIAN_EGPIO(0, 7) +#define EGPIO_MAGICIAN_SPK_POWER MAGICIAN_EGPIO(1, 0) +#define EGPIO_MAGICIAN_EP_POWER MAGICIAN_EGPIO(1, 1) +#define EGPIO_MAGICIAN_IN_SEL0 MAGICIAN_EGPIO(1, 2) +#define EGPIO_MAGICIAN_IN_SEL1 MAGICIAN_EGPIO(1, 3) +#define EGPIO_MAGICIAN_MIC_POWER MAGICIAN_EGPIO(1, 4) +#define EGPIO_MAGICIAN_CODEC_RESET MAGICIAN_EGPIO(1, 5) +#define EGPIO_MAGICIAN_CODEC_POWER MAGICIAN_EGPIO(1, 6) +#define EGPIO_MAGICIAN_BL_POWER MAGICIAN_EGPIO(1, 7) +#define EGPIO_MAGICIAN_SD_POWER MAGICIAN_EGPIO(2, 0) +#define EGPIO_MAGICIAN_CARKIT_MIC MAGICIAN_EGPIO(2, 1) +#define EGPIO_MAGICIAN_IR_RX_SHUTDOWN MAGICIAN_EGPIO(2, 2) +#define EGPIO_MAGICIAN_FLASH_VPP MAGICIAN_EGPIO(2, 3) +#define EGPIO_MAGICIAN_BL_POWER2 MAGICIAN_EGPIO(2, 4) +#define EGPIO_MAGICIAN_BQ24022_ISET2 MAGICIAN_EGPIO(2, 5) +#define EGPIO_MAGICIAN_NICD_CHARGE MAGICIAN_EGPIO(2, 6) +#define EGPIO_MAGICIAN_GSM_POWER MAGICIAN_EGPIO(2, 7) + +/* input */ + +/* USB or AC charger type */ +#define EGPIO_MAGICIAN_CABLE_TYPE MAGICIAN_EGPIO(4, 0) +/* + * Vbus is detected + * FIXME behaves like (6,3), may differ for host/device + */ +#define EGPIO_MAGICIAN_CABLE_VBUS MAGICIAN_EGPIO(4, 1) + +#define EGPIO_MAGICIAN_BOARD_ID0 MAGICIAN_EGPIO(5, 0) +#define EGPIO_MAGICIAN_BOARD_ID1 MAGICIAN_EGPIO(5, 1) +#define EGPIO_MAGICIAN_BOARD_ID2 MAGICIAN_EGPIO(5, 2) +#define EGPIO_MAGICIAN_LCD_SELECT MAGICIAN_EGPIO(5, 3) +#define EGPIO_MAGICIAN_nSD_READONLY MAGICIAN_EGPIO(5, 4) + +#define EGPIO_MAGICIAN_EP_INSERT MAGICIAN_EGPIO(6, 1) +/* FIXME behaves like (4,1), may differ for host/device */ +#define EGPIO_MAGICIAN_CABLE_INSERTED MAGICIAN_EGPIO(6, 3) + +#endif /* _MAGICIAN_H_ */ diff --git a/arch/arm/mach-pxa/include/mach/mainstone.h b/arch/arm/mach-pxa/include/mach/mainstone.h new file mode 100644 index 000000000..1698f2ffd --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/mainstone.h @@ -0,0 +1,142 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ +/* + * arch/arm/mach-pxa/include/mach/mainstone.h + * + * Author: Nicolas Pitre + * Created: Nov 14, 2002 + * Copyright: MontaVista Software Inc. + */ + +#ifndef ASM_ARCH_MAINSTONE_H +#define ASM_ARCH_MAINSTONE_H + +#include <mach/irqs.h> + +#define MST_ETH_PHYS PXA_CS4_PHYS + +#define MST_FPGA_PHYS PXA_CS2_PHYS +#define MST_FPGA_VIRT (0xf0000000) +#define MST_P2V(x) ((x) - MST_FPGA_PHYS + MST_FPGA_VIRT) +#define MST_V2P(x) ((x) - MST_FPGA_VIRT + MST_FPGA_PHYS) + +#ifndef __ASSEMBLY__ +# define __MST_REG(x) (*((volatile unsigned long *)MST_P2V(x))) +#else +# define __MST_REG(x) MST_P2V(x) +#endif + +/* board level registers in the FPGA */ + +#define MST_LEDDAT1 __MST_REG(0x08000010) +#define MST_LEDDAT2 __MST_REG(0x08000014) +#define MST_LEDCTRL __MST_REG(0x08000040) +#define MST_GPSWR __MST_REG(0x08000060) +#define MST_MSCWR1 __MST_REG(0x08000080) +#define MST_MSCWR2 __MST_REG(0x08000084) +#define MST_MSCWR3 __MST_REG(0x08000088) +#define MST_MSCRD __MST_REG(0x08000090) +#define MST_INTMSKENA __MST_REG(0x080000c0) +#define MST_INTSETCLR __MST_REG(0x080000d0) +#define MST_PCMCIA0 __MST_REG(0x080000e0) +#define MST_PCMCIA1 __MST_REG(0x080000e4) + +#define MST_MSCWR1_CAMERA_ON (1 << 15) /* Camera interface power control */ +#define MST_MSCWR1_CAMERA_SEL (1 << 14) /* Camera interface mux control */ +#define MST_MSCWR1_LCD_CTL (1 << 13) /* General-purpose LCD control */ +#define MST_MSCWR1_MS_ON (1 << 12) /* Memory Stick power control */ +#define MST_MSCWR1_MMC_ON (1 << 11) /* MultiMediaCard* power control */ +#define MST_MSCWR1_MS_SEL (1 << 10) /* SD/MS multiplexer control */ +#define MST_MSCWR1_BB_SEL (1 << 9) /* PCMCIA/Baseband multiplexer */ +#define MST_MSCWR1_BT_ON (1 << 8) /* Bluetooth UART transceiver */ +#define MST_MSCWR1_BTDTR (1 << 7) /* Bluetooth UART DTR */ + +#define MST_MSCWR1_IRDA_MASK (3 << 5) /* IrDA transceiver mode */ +#define MST_MSCWR1_IRDA_FULL (0 << 5) /* full distance power */ +#define MST_MSCWR1_IRDA_OFF (1 << 5) /* shutdown */ +#define MST_MSCWR1_IRDA_MED (2 << 5) /* 2/3 distance power */ +#define MST_MSCWR1_IRDA_LOW (3 << 5) /* 1/3 distance power */ + +#define MST_MSCWR1_IRDA_FIR (1 << 4) /* IrDA transceiver SIR/FIR */ +#define MST_MSCWR1_GREENLED (1 << 3) /* LED D1 control */ +#define MST_MSCWR1_PDC_CTL (1 << 2) /* reserved */ +#define MST_MSCWR1_MTR_ON (1 << 1) /* Silent alert motor */ +#define MST_MSCWR1_SYSRESET (1 << 0) /* System reset */ + +#define MST_MSCWR2_USB_OTG_RST (1 << 6) /* USB On The Go reset */ +#define MST_MSCWR2_USB_OTG_SEL (1 << 5) /* USB On The Go control */ +#define MST_MSCWR2_nUSBC_SC (1 << 4) /* USB client soft connect control */ +#define MST_MSCWR2_I2S_SPKROFF (1 << 3) /* I2S CODEC amplifier control */ +#define MST_MSCWR2_AC97_SPKROFF (1 << 2) /* AC97 CODEC amplifier control */ +#define MST_MSCWR2_RADIO_PWR (1 << 1) /* Radio module power control */ +#define MST_MSCWR2_RADIO_WAKE (1 << 0) /* Radio module wake-up signal */ + +#define MST_MSCWR3_GPIO_RESET_EN (1 << 2) /* Enable GPIO Reset */ +#define MST_MSCWR3_GPIO_RESET (1 << 1) /* Initiate a GPIO Reset */ +#define MST_MSCWR3_COMMS_SW_RESET (1 << 0) /* Communications Processor Reset Control */ + +#define MST_MSCRD_nPENIRQ (1 << 9) /* ADI7873* nPENIRQ signal */ +#define MST_MSCRD_nMEMSTK_CD (1 << 8) /* Memory Stick detection signal */ +#define MST_MSCRD_nMMC_CD (1 << 7) /* SD/MMC card detection signal */ +#define MST_MSCRD_nUSIM_CD (1 << 6) /* USIM card detection signal */ +#define MST_MSCRD_USB_CBL (1 << 5) /* USB client cable status */ +#define MST_MSCRD_TS_BUSY (1 << 4) /* ADI7873 busy */ +#define MST_MSCRD_BTDSR (1 << 3) /* Bluetooth UART DSR */ +#define MST_MSCRD_BTRI (1 << 2) /* Bluetooth UART Ring Indicator */ +#define MST_MSCRD_BTDCD (1 << 1) /* Bluetooth UART DCD */ +#define MST_MSCRD_nMMC_WP (1 << 0) /* SD/MMC write-protect status */ + +#define MST_INT_S1_IRQ (1 << 15) /* PCMCIA socket 1 IRQ */ +#define MST_INT_S1_STSCHG (1 << 14) /* PCMCIA socket 1 status changed */ +#define MST_INT_S1_CD (1 << 13) /* PCMCIA socket 1 card detection */ +#define MST_INT_S0_IRQ (1 << 11) /* PCMCIA socket 0 IRQ */ +#define MST_INT_S0_STSCHG (1 << 10) /* PCMCIA socket 0 status changed */ +#define MST_INT_S0_CD (1 << 9) /* PCMCIA socket 0 card detection */ +#define MST_INT_nEXBRD_INT (1 << 7) /* Expansion board IRQ */ +#define MST_INT_MSINS (1 << 6) /* Memory Stick* detection */ +#define MST_INT_PENIRQ (1 << 5) /* ADI7873* touch-screen IRQ */ +#define MST_INT_AC97 (1 << 4) /* AC'97 CODEC IRQ */ +#define MST_INT_ETHERNET (1 << 3) /* Ethernet controller IRQ */ +#define MST_INT_USBC (1 << 2) /* USB client cable detection IRQ */ +#define MST_INT_USIM (1 << 1) /* USIM card detection IRQ */ +#define MST_INT_MMC (1 << 0) /* MMC/SD card detection IRQ */ + +#define MST_PCMCIA_nIRQ (1 << 10) /* IRQ / ready signal */ +#define MST_PCMCIA_nSPKR_BVD2 (1 << 9) /* VDD sense / digital speaker */ +#define MST_PCMCIA_nSTSCHG_BVD1 (1 << 8) /* VDD sense / card status changed */ +#define MST_PCMCIA_nVS2 (1 << 7) /* VSS voltage sense */ +#define MST_PCMCIA_nVS1 (1 << 6) /* VSS voltage sense */ +#define MST_PCMCIA_nCD (1 << 5) /* Card detection signal */ +#define MST_PCMCIA_RESET (1 << 4) /* Card reset signal */ +#define MST_PCMCIA_PWR_MASK (0x000f) /* MAX1602 power-supply controls */ + +#define MST_PCMCIA_PWR_VPP_0 0x0 /* voltage VPP = 0V */ +#define MST_PCMCIA_PWR_VPP_120 0x2 /* voltage VPP = 12V*/ +#define MST_PCMCIA_PWR_VPP_VCC 0x1 /* voltage VPP = VCC */ +#define MST_PCMCIA_PWR_VCC_0 0x0 /* voltage VCC = 0V */ +#define MST_PCMCIA_PWR_VCC_33 0x8 /* voltage VCC = 3.3V */ +#define MST_PCMCIA_PWR_VCC_50 0x4 /* voltage VCC = 5.0V */ + +#define MST_PCMCIA_INPUTS \ + (MST_PCMCIA_nIRQ | MST_PCMCIA_nSPKR_BVD2 | MST_PCMCIA_nSTSCHG_BVD1 | \ + MST_PCMCIA_nVS2 | MST_PCMCIA_nVS1 | MST_PCMCIA_nCD) + +/* board specific IRQs */ +#define MAINSTONE_NR_IRQS IRQ_BOARD_START + +#define MAINSTONE_IRQ(x) (MAINSTONE_NR_IRQS + (x)) +#define MAINSTONE_MMC_IRQ MAINSTONE_IRQ(0) +#define MAINSTONE_USIM_IRQ MAINSTONE_IRQ(1) +#define MAINSTONE_USBC_IRQ MAINSTONE_IRQ(2) +#define MAINSTONE_ETHERNET_IRQ MAINSTONE_IRQ(3) +#define MAINSTONE_AC97_IRQ MAINSTONE_IRQ(4) +#define MAINSTONE_PEN_IRQ MAINSTONE_IRQ(5) +#define MAINSTONE_MSINS_IRQ MAINSTONE_IRQ(6) +#define MAINSTONE_EXBRD_IRQ MAINSTONE_IRQ(7) +#define MAINSTONE_S0_CD_IRQ MAINSTONE_IRQ(9) +#define MAINSTONE_S0_STSCHG_IRQ MAINSTONE_IRQ(10) +#define MAINSTONE_S0_IRQ MAINSTONE_IRQ(11) +#define MAINSTONE_S1_CD_IRQ MAINSTONE_IRQ(13) +#define MAINSTONE_S1_STSCHG_IRQ MAINSTONE_IRQ(14) +#define MAINSTONE_S1_IRQ MAINSTONE_IRQ(15) + +#endif diff --git a/arch/arm/mach-pxa/include/mach/mfp.h b/arch/arm/mach-pxa/include/mach/mfp.h new file mode 100644 index 000000000..dbb961fb5 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/mfp.h @@ -0,0 +1,18 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ +/* + * arch/arm/mach-pxa/include/mach/mfp.h + * + * Multi-Function Pin Definitions + * + * Copyright (C) 2007 Marvell International Ltd. + * + * 2007-8-21: eric miao <eric.miao@marvell.com> + * initial version + */ + +#ifndef __ASM_ARCH_MFP_H +#define __ASM_ARCH_MFP_H + +#include <plat/mfp.h> + +#endif /* __ASM_ARCH_MFP_H */ diff --git a/arch/arm/mach-pxa/include/mach/mtd-xip.h b/arch/arm/mach-pxa/include/mach/mtd-xip.h new file mode 100644 index 000000000..4b31bef9e --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/mtd-xip.h @@ -0,0 +1,36 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ +/* + * MTD primitives for XIP support. Architecture specific functions + * + * Do not include this file directly. It's included from linux/mtd/xip.h + * + * Author: Nicolas Pitre + * Created: Nov 2, 2004 + * Copyright: (C) 2004 MontaVista Software, Inc. + */ + +#ifndef __ARCH_PXA_MTD_XIP_H__ +#define __ARCH_PXA_MTD_XIP_H__ + +#include <mach/regs-ost.h> + +/* restored July 2017, this did not build since 2011! */ + +#define ICIP io_p2v(0x40d00000) +#define ICMR io_p2v(0x40d00004) +#define xip_irqpending() (readl(ICIP) & readl(ICMR)) + +/* we sample OSCR and convert desired delta to usec (1/4 ~= 1000000/3686400) */ +#define xip_currtime() readl(OSCR) +#define xip_elapsed_since(x) (signed)((readl(OSCR) - (x)) / 4) + +/* + * xip_cpu_idle() is used when waiting for a delay equal or larger than + * the system timer tick period. This should put the CPU into idle mode + * to save power and to be woken up only when some interrupts are pending. + * As above, this should not rely upon standard kernel code. + */ + +#define xip_cpu_idle() asm volatile ("mcr p14, 0, %0, c7, c0, 0" :: "r" (1)) + +#endif /* __ARCH_PXA_MTD_XIP_H__ */ diff --git a/arch/arm/mach-pxa/include/mach/palmld.h b/arch/arm/mach-pxa/include/mach/palmld.h new file mode 100644 index 000000000..99a6d8b3a --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/palmld.h @@ -0,0 +1,107 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ +/* + * GPIOs and interrupts for Palm LifeDrive Handheld Computer + * + * Authors: Alex Osborne <ato@meshy.org> + * Marek Vasut <marek.vasut@gmail.com> + */ + +#ifndef _INCLUDE_PALMLD_H_ +#define _INCLUDE_PALMLD_H_ + +#include "irqs.h" /* PXA_GPIO_TO_IRQ */ + +/** HERE ARE GPIOs **/ + +/* GPIOs */ +#define GPIO_NR_PALMLD_GPIO_RESET 1 +#define GPIO_NR_PALMLD_POWER_DETECT 4 +#define GPIO_NR_PALMLD_HOTSYNC_BUTTON_N 10 +#define GPIO_NR_PALMLD_POWER_SWITCH 12 +#define GPIO_NR_PALMLD_EARPHONE_DETECT 13 +#define GPIO_NR_PALMLD_LOCK_SWITCH 15 + +/* SD/MMC */ +#define GPIO_NR_PALMLD_SD_DETECT_N 14 +#define GPIO_NR_PALMLD_SD_POWER 114 +#define GPIO_NR_PALMLD_SD_READONLY 116 + +/* TOUCHSCREEN */ +#define GPIO_NR_PALMLD_WM9712_IRQ 27 + +/* IRDA */ +#define GPIO_NR_PALMLD_IR_DISABLE 108 + +/* LCD/BACKLIGHT */ +#define GPIO_NR_PALMLD_BL_POWER 19 +#define GPIO_NR_PALMLD_LCD_POWER 96 + +/* LCD BORDER */ +#define GPIO_NR_PALMLD_BORDER_SWITCH 21 +#define GPIO_NR_PALMLD_BORDER_SELECT 22 + +/* BLUETOOTH */ +#define GPIO_NR_PALMLD_BT_POWER 17 +#define GPIO_NR_PALMLD_BT_RESET 83 + +/* PCMCIA (WiFi) */ +#define GPIO_NR_PALMLD_PCMCIA_READY 38 +#define GPIO_NR_PALMLD_PCMCIA_POWER 36 +#define GPIO_NR_PALMLD_PCMCIA_RESET 81 + +/* LEDs */ +#define GPIO_NR_PALMLD_LED_GREEN 52 +#define GPIO_NR_PALMLD_LED_AMBER 94 + +/* IDE */ +#define GPIO_NR_PALMLD_IDE_RESET 98 +#define GPIO_NR_PALMLD_IDE_PWEN 115 + +/* USB */ +#define GPIO_NR_PALMLD_USB_DETECT_N 3 +#define GPIO_NR_PALMLD_USB_READY 86 +#define GPIO_NR_PALMLD_USB_RESET 88 +#define GPIO_NR_PALMLD_USB_INT 106 +#define GPIO_NR_PALMLD_USB_POWER 118 +/* 20, 53 and 86 are usb related too */ + +/* INTERRUPTS */ +#define IRQ_GPIO_PALMLD_GPIO_RESET PXA_GPIO_TO_IRQ(GPIO_NR_PALMLD_GPIO_RESET) +#define IRQ_GPIO_PALMLD_SD_DETECT_N PXA_GPIO_TO_IRQ(GPIO_NR_PALMLD_SD_DETECT_N) +#define IRQ_GPIO_PALMLD_WM9712_IRQ PXA_GPIO_TO_IRQ(GPIO_NR_PALMLD_WM9712_IRQ) +#define IRQ_GPIO_PALMLD_IDE_IRQ PXA_GPIO_TO_IRQ(GPIO_NR_PALMLD_IDE_IRQ) + + +/** HERE ARE INIT VALUES **/ + +/* IO mappings */ +#define PALMLD_USB_PHYS PXA_CS2_PHYS +#define PALMLD_USB_VIRT 0xf0000000 +#define PALMLD_USB_SIZE 0x00100000 + +#define PALMLD_IDE_PHYS 0x20000000 +#define PALMLD_IDE_VIRT 0xf1000000 +#define PALMLD_IDE_SIZE 0x00100000 + +#define PALMLD_PHYS_IO_START 0x40000000 +#define PALMLD_STR_BASE 0xa0200000 + +/* BATTERY */ +#define PALMLD_BAT_MAX_VOLTAGE 4000 /* 4.00V maximum voltage */ +#define PALMLD_BAT_MIN_VOLTAGE 3550 /* 3.55V critical voltage */ +#define PALMLD_BAT_MAX_CURRENT 0 /* unknown */ +#define PALMLD_BAT_MIN_CURRENT 0 /* unknown */ +#define PALMLD_BAT_MAX_CHARGE 1 /* unknown */ +#define PALMLD_BAT_MIN_CHARGE 1 /* unknown */ +#define PALMLD_MAX_LIFE_MINS 240 /* on-life in minutes */ + +#define PALMLD_BAT_MEASURE_DELAY (HZ * 1) + +/* BACKLIGHT */ +#define PALMLD_MAX_INTENSITY 0xFE +#define PALMLD_DEFAULT_INTENSITY 0x7E +#define PALMLD_LIMIT_MASK 0x7F +#define PALMLD_PRESCALER 0x3F +#define PALMLD_PERIOD_NS 3500 + +#endif diff --git a/arch/arm/mach-pxa/include/mach/palmtc.h b/arch/arm/mach-pxa/include/mach/palmtc.h new file mode 100644 index 000000000..9257a02c4 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/palmtc.h @@ -0,0 +1,84 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ +/* + * linux/include/asm-arm/arch-pxa/palmtc-gpio.h + * + * GPIOs and interrupts for Palm Tungsten|C Handheld Computer + * + * Authors: Alex Osborne <bobofdoom@gmail.com> + * Marek Vasut <marek.vasut@gmail.com> + * Holger Bocklet <bitz.email@gmx.net> + */ + +#ifndef _INCLUDE_PALMTC_H_ +#define _INCLUDE_PALMTC_H_ + +#include "irqs.h" /* PXA_GPIO_TO_IRQ */ + +/** HERE ARE GPIOs **/ + +/* GPIOs */ +#define GPIO_NR_PALMTC_EARPHONE_DETECT 2 +#define GPIO_NR_PALMTC_CRADLE_DETECT 5 +#define GPIO_NR_PALMTC_HOTSYNC_BUTTON 7 + +/* SD/MMC */ +#define GPIO_NR_PALMTC_SD_DETECT_N 12 +#define GPIO_NR_PALMTC_SD_POWER 32 +#define GPIO_NR_PALMTC_SD_READONLY 54 + +/* WLAN */ +#define GPIO_NR_PALMTC_PCMCIA_READY 13 +#define GPIO_NR_PALMTC_PCMCIA_PWRREADY 14 +#define GPIO_NR_PALMTC_PCMCIA_POWER1 15 +#define GPIO_NR_PALMTC_PCMCIA_POWER2 33 +#define GPIO_NR_PALMTC_PCMCIA_POWER3 55 +#define GPIO_NR_PALMTC_PCMCIA_RESET 78 + +/* UDC */ +#define GPIO_NR_PALMTC_USB_DETECT_N 4 +#define GPIO_NR_PALMTC_USB_POWER 36 + +/* LCD/BACKLIGHT */ +#define GPIO_NR_PALMTC_BL_POWER 16 +#define GPIO_NR_PALMTC_LCD_POWER 44 +#define GPIO_NR_PALMTC_LCD_BLANK 38 + +/* UART */ +#define GPIO_NR_PALMTC_RS232_POWER 37 + +/* IRDA */ +#define GPIO_NR_PALMTC_IR_DISABLE 45 + +/* IRQs */ +#define IRQ_GPIO_PALMTC_SD_DETECT_N PXA_GPIO_TO_IRQ(GPIO_NR_PALMTC_SD_DETECT_N) +#define IRQ_GPIO_PALMTC_WLAN_READY PXA_GPIO_TO_IRQ(GPIO_NR_PALMTC_WLAN_READY) + +/* UCB1400 GPIOs */ +#define GPIO_NR_PALMTC_POWER_DETECT (0x80 | 0x00) +#define GPIO_NR_PALMTC_HEADPHONE_DETECT (0x80 | 0x01) +#define GPIO_NR_PALMTC_SPEAKER_ENABLE (0x80 | 0x03) +#define GPIO_NR_PALMTC_VIBRA_POWER (0x80 | 0x05) +#define GPIO_NR_PALMTC_LED_POWER (0x80 | 0x07) + +/** HERE ARE INIT VALUES **/ +#define PALMTC_UCB1400_GPIO_OFFSET 0x80 + +/* BATTERY */ +#define PALMTC_BAT_MAX_VOLTAGE 4000 /* 4.00V maximum voltage */ +#define PALMTC_BAT_MIN_VOLTAGE 3550 /* 3.55V critical voltage */ +#define PALMTC_BAT_MAX_CURRENT 0 /* unknown */ +#define PALMTC_BAT_MIN_CURRENT 0 /* unknown */ +#define PALMTC_BAT_MAX_CHARGE 1 /* unknown */ +#define PALMTC_BAT_MIN_CHARGE 1 /* unknown */ +#define PALMTC_MAX_LIFE_MINS 240 /* on-life in minutes */ + +#define PALMTC_BAT_MEASURE_DELAY (HZ * 1) + +/* BACKLIGHT */ +#define PALMTC_MAX_INTENSITY 0xFE +#define PALMTC_DEFAULT_INTENSITY 0x7E +#define PALMTC_LIMIT_MASK 0x7F +#define PALMTC_PRESCALER 0x3F +#define PALMTC_PERIOD_NS 3500 + +#endif diff --git a/arch/arm/mach-pxa/include/mach/palmtx.h b/arch/arm/mach-pxa/include/mach/palmtx.h new file mode 100644 index 000000000..ec88abf0f --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/palmtx.h @@ -0,0 +1,110 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ +/* + * GPIOs and interrupts for Palm T|X Handheld Computer + * + * Based on palmld-gpio.h by Alex Osborne + * + * Authors: Marek Vasut <marek.vasut@gmail.com> + * Cristiano P. <cristianop@users.sourceforge.net> + * Jan Herman <2hp@seznam.cz> + */ + +#ifndef _INCLUDE_PALMTX_H_ +#define _INCLUDE_PALMTX_H_ + +#include "irqs.h" /* PXA_GPIO_TO_IRQ */ + +/** HERE ARE GPIOs **/ + +/* GPIOs */ +#define GPIO_NR_PALMTX_GPIO_RESET 1 + +#define GPIO_NR_PALMTX_POWER_DETECT 12 /* 90 */ +#define GPIO_NR_PALMTX_HOTSYNC_BUTTON_N 10 +#define GPIO_NR_PALMTX_EARPHONE_DETECT 107 + +/* SD/MMC */ +#define GPIO_NR_PALMTX_SD_DETECT_N 14 +#define GPIO_NR_PALMTX_SD_POWER 114 /* probably */ +#define GPIO_NR_PALMTX_SD_READONLY 115 /* probably */ + +/* TOUCHSCREEN */ +#define GPIO_NR_PALMTX_WM9712_IRQ 27 + +/* IRDA - disable GPIO connected to SD pin of tranceiver (TFBS4710?) ? */ +#define GPIO_NR_PALMTX_IR_DISABLE 40 + +/* USB */ +#define GPIO_NR_PALMTX_USB_DETECT_N 13 +#define GPIO_NR_PALMTX_USB_PULLUP 93 + +/* LCD/BACKLIGHT */ +#define GPIO_NR_PALMTX_BL_POWER 84 +#define GPIO_NR_PALMTX_LCD_POWER 96 + +/* LCD BORDER */ +#define GPIO_NR_PALMTX_BORDER_SWITCH 98 +#define GPIO_NR_PALMTX_BORDER_SELECT 22 + +/* BLUETOOTH */ +#define GPIO_NR_PALMTX_BT_POWER 17 +#define GPIO_NR_PALMTX_BT_RESET 83 + +/* PCMCIA (WiFi) */ +#define GPIO_NR_PALMTX_PCMCIA_POWER1 94 +#define GPIO_NR_PALMTX_PCMCIA_POWER2 108 +#define GPIO_NR_PALMTX_PCMCIA_RESET 79 +#define GPIO_NR_PALMTX_PCMCIA_READY 116 + +/* NAND Flash ... this GPIO may be incorrect! */ +#define GPIO_NR_PALMTX_NAND_BUFFER_DIR 79 + +/* INTERRUPTS */ +#define IRQ_GPIO_PALMTX_SD_DETECT_N PXA_GPIO_TO_IRQ(GPIO_NR_PALMTX_SD_DETECT_N) +#define IRQ_GPIO_PALMTX_WM9712_IRQ PXA_GPIO_TO_IRQ(GPIO_NR_PALMTX_WM9712_IRQ) +#define IRQ_GPIO_PALMTX_USB_DETECT PXA_GPIO_TO_IRQ(GPIO_NR_PALMTX_USB_DETECT) +#define IRQ_GPIO_PALMTX_GPIO_RESET PXA_GPIO_TO_IRQ(GPIO_NR_PALMTX_GPIO_RESET) + +/** HERE ARE INIT VALUES **/ + +/* Various addresses */ +#define PALMTX_PCMCIA_PHYS 0x28000000 +#define PALMTX_PCMCIA_VIRT IOMEM(0xf0000000) +#define PALMTX_PCMCIA_SIZE 0x100000 + +#define PALMTX_PHYS_RAM_START 0xa0000000 +#define PALMTX_PHYS_IO_START 0x40000000 + +#define PALMTX_STR_BASE 0xa0200000 + +#define PALMTX_PHYS_FLASH_START PXA_CS0_PHYS /* ChipSelect 0 */ +#define PALMTX_PHYS_NAND_START PXA_CS1_PHYS /* ChipSelect 1 */ + +#define PALMTX_NAND_ALE_PHYS (PALMTX_PHYS_NAND_START | (1 << 24)) +#define PALMTX_NAND_CLE_PHYS (PALMTX_PHYS_NAND_START | (1 << 25)) +#define PALMTX_NAND_ALE_VIRT IOMEM(0xff100000) +#define PALMTX_NAND_CLE_VIRT IOMEM(0xff200000) + +/* TOUCHSCREEN */ +#define AC97_LINK_FRAME 21 + + +/* BATTERY */ +#define PALMTX_BAT_MAX_VOLTAGE 4000 /* 4.00v current voltage */ +#define PALMTX_BAT_MIN_VOLTAGE 3550 /* 3.55v critical voltage */ +#define PALMTX_BAT_MAX_CURRENT 0 /* unknown */ +#define PALMTX_BAT_MIN_CURRENT 0 /* unknown */ +#define PALMTX_BAT_MAX_CHARGE 1 /* unknown */ +#define PALMTX_BAT_MIN_CHARGE 1 /* unknown */ +#define PALMTX_MAX_LIFE_MINS 360 /* on-life in minutes */ + +#define PALMTX_BAT_MEASURE_DELAY (HZ * 1) + +/* BACKLIGHT */ +#define PALMTX_MAX_INTENSITY 0xFE +#define PALMTX_DEFAULT_INTENSITY 0x7E +#define PALMTX_LIMIT_MASK 0x7F +#define PALMTX_PRESCALER 0x3F +#define PALMTX_PERIOD_NS 3500 + +#endif diff --git a/arch/arm/mach-pxa/include/mach/poodle.h b/arch/arm/mach-pxa/include/mach/poodle.h new file mode 100644 index 000000000..b56b19351 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/poodle.h @@ -0,0 +1,94 @@ +/* + * arch/arm/mach-pxa/include/mach/poodle.h + * + * May be copied or modified under the terms of the GNU General Public + * License. See linux/COPYING for more information. + * + * Based on: + * arch/arm/mach-sa1100/include/mach/collie.h + * + * ChangeLog: + * 04-06-2001 Lineo Japan, Inc. + * 04-16-2001 SHARP Corporation + * Update to 2.6 John Lenz + */ +#ifndef __ASM_ARCH_POODLE_H +#define __ASM_ARCH_POODLE_H 1 + +#include "irqs.h" /* PXA_GPIO_TO_IRQ */ + +/* + * GPIOs + */ +/* PXA GPIOs */ +#define POODLE_GPIO_ON_KEY (0) +#define POODLE_GPIO_AC_IN (1) +#define POODLE_GPIO_CO 16 +#define POODLE_GPIO_TP_INT (5) +#define POODLE_GPIO_TP_CS (24) +#define POODLE_GPIO_WAKEUP (11) /* change battery */ +#define POODLE_GPIO_GA_INT (10) +#define POODLE_GPIO_IR_ON (22) +#define POODLE_GPIO_HP_IN (4) +#define POODLE_GPIO_CF_IRQ (17) +#define POODLE_GPIO_CF_CD (14) +#define POODLE_GPIO_CF_STSCHG (14) +#define POODLE_GPIO_SD_PWR (33) +#define POODLE_GPIO_SD_PWR1 (3) +#define POODLE_GPIO_nSD_CLK (6) +#define POODLE_GPIO_nSD_WP (7) +#define POODLE_GPIO_nSD_INT (8) +#define POODLE_GPIO_nSD_DETECT (9) +#define POODLE_GPIO_MAIN_BAT_LOW (13) +#define POODLE_GPIO_BAT_COVER (13) +#define POODLE_GPIO_USB_PULLUP (20) +#define POODLE_GPIO_ADC_TEMP_ON (21) +#define POODLE_GPIO_BYPASS_ON (36) +#define POODLE_GPIO_CHRG_ON (38) +#define POODLE_GPIO_CHRG_FULL (16) +#define POODLE_GPIO_DISCHARGE_ON (42) /* Enable battery discharge */ + +/* PXA GPIOs */ +#define POODLE_IRQ_GPIO_ON_KEY PXA_GPIO_TO_IRQ(0) +#define POODLE_IRQ_GPIO_AC_IN PXA_GPIO_TO_IRQ(1) +#define POODLE_IRQ_GPIO_HP_IN PXA_GPIO_TO_IRQ(4) +#define POODLE_IRQ_GPIO_CO PXA_GPIO_TO_IRQ(16) +#define POODLE_IRQ_GPIO_TP_INT PXA_GPIO_TO_IRQ(5) +#define POODLE_IRQ_GPIO_WAKEUP PXA_GPIO_TO_IRQ(11) +#define POODLE_IRQ_GPIO_GA_INT PXA_GPIO_TO_IRQ(10) +#define POODLE_IRQ_GPIO_CF_IRQ PXA_GPIO_TO_IRQ(17) +#define POODLE_IRQ_GPIO_CF_CD PXA_GPIO_TO_IRQ(14) +#define POODLE_IRQ_GPIO_nSD_INT PXA_GPIO_TO_IRQ(8) +#define POODLE_IRQ_GPIO_nSD_DETECT PXA_GPIO_TO_IRQ(9) +#define POODLE_IRQ_GPIO_MAIN_BAT_LOW PXA_GPIO_TO_IRQ(13) + +/* SCOOP GPIOs */ +#define POODLE_SCOOP_CHARGE_ON SCOOP_GPCR_PA11 +#define POODLE_SCOOP_CP401 SCOOP_GPCR_PA13 +#define POODLE_SCOOP_VPEN SCOOP_GPCR_PA18 +#define POODLE_SCOOP_L_PCLK SCOOP_GPCR_PA20 +#define POODLE_SCOOP_L_LCLK SCOOP_GPCR_PA21 +#define POODLE_SCOOP_HS_OUT SCOOP_GPCR_PA22 + +#define POODLE_SCOOP_IO_DIR ( POODLE_SCOOP_VPEN | POODLE_SCOOP_HS_OUT ) +#define POODLE_SCOOP_IO_OUT ( 0 ) + +#define POODLE_SCOOP_GPIO_BASE (PXA_NR_BUILTIN_GPIO) +#define POODLE_GPIO_CHARGE_ON (POODLE_SCOOP_GPIO_BASE + 0) +#define POODLE_GPIO_CP401 (POODLE_SCOOP_GPIO_BASE + 2) +#define POODLE_GPIO_VPEN (POODLE_SCOOP_GPIO_BASE + 7) +#define POODLE_GPIO_L_PCLK (POODLE_SCOOP_GPIO_BASE + 9) +#define POODLE_GPIO_L_LCLK (POODLE_SCOOP_GPIO_BASE + 10) +#define POODLE_GPIO_HS_OUT (POODLE_SCOOP_GPIO_BASE + 11) + +#define POODLE_LOCOMO_GPIO_AMP_ON LOCOMO_GPIO(8) +#define POODLE_LOCOMO_GPIO_MUTE_L LOCOMO_GPIO(10) +#define POODLE_LOCOMO_GPIO_MUTE_R LOCOMO_GPIO(11) +#define POODLE_LOCOMO_GPIO_232VCC_ON LOCOMO_GPIO(12) +#define POODLE_LOCOMO_GPIO_JK_B LOCOMO_GPIO(13) + +#define POODLE_NR_IRQS (IRQ_BOARD_START + 4) /* 4 for LoCoMo */ + +extern struct platform_device poodle_locomo_device; + +#endif /* __ASM_ARCH_POODLE_H */ diff --git a/arch/arm/mach-pxa/include/mach/pxa2xx-regs.h b/arch/arm/mach-pxa/include/mach/pxa2xx-regs.h new file mode 100644 index 000000000..fa121e135 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/pxa2xx-regs.h @@ -0,0 +1,194 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ +/* + * arch/arm/mach-pxa/include/mach/pxa2xx-regs.h + * + * Taken from pxa-regs.h by Russell King + * + * Author: Nicolas Pitre + * Copyright: MontaVista Software Inc. + */ + +#ifndef __PXA2XX_REGS_H +#define __PXA2XX_REGS_H + +#include <mach/hardware.h> + +/* + * Power Manager + */ + +#define PMCR __REG(0x40F00000) /* Power Manager Control Register */ +#define PSSR __REG(0x40F00004) /* Power Manager Sleep Status Register */ +#define PSPR __REG(0x40F00008) /* Power Manager Scratch Pad Register */ +#define PWER __REG(0x40F0000C) /* Power Manager Wake-up Enable Register */ +#define PRER __REG(0x40F00010) /* Power Manager GPIO Rising-Edge Detect Enable Register */ +#define PFER __REG(0x40F00014) /* Power Manager GPIO Falling-Edge Detect Enable Register */ +#define PEDR __REG(0x40F00018) /* Power Manager GPIO Edge Detect Status Register */ +#define PCFR __REG(0x40F0001C) /* Power Manager General Configuration Register */ +#define PGSR0 __REG(0x40F00020) /* Power Manager GPIO Sleep State Register for GP[31-0] */ +#define PGSR1 __REG(0x40F00024) /* Power Manager GPIO Sleep State Register for GP[63-32] */ +#define PGSR2 __REG(0x40F00028) /* Power Manager GPIO Sleep State Register for GP[84-64] */ +#define PGSR3 __REG(0x40F0002C) /* Power Manager GPIO Sleep State Register for GP[118-96] */ +#define RCSR __REG(0x40F00030) /* Reset Controller Status Register */ + +#define PSLR __REG(0x40F00034) /* Power Manager Sleep Config Register */ +#define PSTR __REG(0x40F00038) /* Power Manager Standby Config Register */ +#define PSNR __REG(0x40F0003C) /* Power Manager Sense Config Register */ +#define PVCR __REG(0x40F00040) /* Power Manager VoltageControl Register */ +#define PKWR __REG(0x40F00050) /* Power Manager KB Wake-up Enable Reg */ +#define PKSR __REG(0x40F00054) /* Power Manager KB Level-Detect Register */ +#define PCMD(x) __REG2(0x40F00080, (x)<<2) +#define PCMD0 __REG(0x40F00080 + 0 * 4) +#define PCMD1 __REG(0x40F00080 + 1 * 4) +#define PCMD2 __REG(0x40F00080 + 2 * 4) +#define PCMD3 __REG(0x40F00080 + 3 * 4) +#define PCMD4 __REG(0x40F00080 + 4 * 4) +#define PCMD5 __REG(0x40F00080 + 5 * 4) +#define PCMD6 __REG(0x40F00080 + 6 * 4) +#define PCMD7 __REG(0x40F00080 + 7 * 4) +#define PCMD8 __REG(0x40F00080 + 8 * 4) +#define PCMD9 __REG(0x40F00080 + 9 * 4) +#define PCMD10 __REG(0x40F00080 + 10 * 4) +#define PCMD11 __REG(0x40F00080 + 11 * 4) +#define PCMD12 __REG(0x40F00080 + 12 * 4) +#define PCMD13 __REG(0x40F00080 + 13 * 4) +#define PCMD14 __REG(0x40F00080 + 14 * 4) +#define PCMD15 __REG(0x40F00080 + 15 * 4) +#define PCMD16 __REG(0x40F00080 + 16 * 4) +#define PCMD17 __REG(0x40F00080 + 17 * 4) +#define PCMD18 __REG(0x40F00080 + 18 * 4) +#define PCMD19 __REG(0x40F00080 + 19 * 4) +#define PCMD20 __REG(0x40F00080 + 20 * 4) +#define PCMD21 __REG(0x40F00080 + 21 * 4) +#define PCMD22 __REG(0x40F00080 + 22 * 4) +#define PCMD23 __REG(0x40F00080 + 23 * 4) +#define PCMD24 __REG(0x40F00080 + 24 * 4) +#define PCMD25 __REG(0x40F00080 + 25 * 4) +#define PCMD26 __REG(0x40F00080 + 26 * 4) +#define PCMD27 __REG(0x40F00080 + 27 * 4) +#define PCMD28 __REG(0x40F00080 + 28 * 4) +#define PCMD29 __REG(0x40F00080 + 29 * 4) +#define PCMD30 __REG(0x40F00080 + 30 * 4) +#define PCMD31 __REG(0x40F00080 + 31 * 4) + +#define PCMD_MBC (1<<12) +#define PCMD_DCE (1<<11) +#define PCMD_LC (1<<10) +/* FIXME: PCMD_SQC need be checked. */ +#define PCMD_SQC (3<<8) /* currently only bit 8 is changeable, + bit 9 should be 0 all day. */ +#define PVCR_VCSA (0x1<<14) +#define PVCR_CommandDelay (0xf80) +#define PCFR_PI2C_EN (0x1 << 6) + +#define PSSR_OTGPH (1 << 6) /* OTG Peripheral control Hold */ +#define PSSR_RDH (1 << 5) /* Read Disable Hold */ +#define PSSR_PH (1 << 4) /* Peripheral Control Hold */ +#define PSSR_STS (1 << 3) /* Standby Mode Status */ +#define PSSR_VFS (1 << 2) /* VDD Fault Status */ +#define PSSR_BFS (1 << 1) /* Battery Fault Status */ +#define PSSR_SSS (1 << 0) /* Software Sleep Status */ + +#define PSLR_SL_ROD (1 << 20) /* Sleep-Mode/Depp-Sleep Mode nRESET_OUT Disable */ + +#define PCFR_RO (1 << 15) /* RDH Override */ +#define PCFR_PO (1 << 14) /* PH Override */ +#define PCFR_GPROD (1 << 12) /* GPIO nRESET_OUT Disable */ +#define PCFR_L1_EN (1 << 11) /* Sleep Mode L1 converter Enable */ +#define PCFR_FVC (1 << 10) /* Frequency/Voltage Change */ +#define PCFR_DC_EN (1 << 7) /* Sleep/deep-sleep DC-DC Converter Enable */ +#define PCFR_PI2CEN (1 << 6) /* Enable PI2C controller */ +#define PCFR_GPR_EN (1 << 4) /* nRESET_GPIO Pin Enable */ +#define PCFR_DS (1 << 3) /* Deep Sleep Mode */ +#define PCFR_FS (1 << 2) /* Float Static Chip Selects */ +#define PCFR_FP (1 << 1) /* Float PCMCIA controls */ +#define PCFR_OPDE (1 << 0) /* 3.6864 MHz oscillator power-down enable */ + +#define RCSR_GPR (1 << 3) /* GPIO Reset */ +#define RCSR_SMR (1 << 2) /* Sleep Mode */ +#define RCSR_WDR (1 << 1) /* Watchdog Reset */ +#define RCSR_HWR (1 << 0) /* Hardware Reset */ + +#define PWER_GPIO(Nb) (1 << Nb) /* GPIO [0..15] wake-up enable */ +#define PWER_GPIO0 PWER_GPIO (0) /* GPIO [0] wake-up enable */ +#define PWER_GPIO1 PWER_GPIO (1) /* GPIO [1] wake-up enable */ +#define PWER_GPIO2 PWER_GPIO (2) /* GPIO [2] wake-up enable */ +#define PWER_GPIO3 PWER_GPIO (3) /* GPIO [3] wake-up enable */ +#define PWER_GPIO4 PWER_GPIO (4) /* GPIO [4] wake-up enable */ +#define PWER_GPIO5 PWER_GPIO (5) /* GPIO [5] wake-up enable */ +#define PWER_GPIO6 PWER_GPIO (6) /* GPIO [6] wake-up enable */ +#define PWER_GPIO7 PWER_GPIO (7) /* GPIO [7] wake-up enable */ +#define PWER_GPIO8 PWER_GPIO (8) /* GPIO [8] wake-up enable */ +#define PWER_GPIO9 PWER_GPIO (9) /* GPIO [9] wake-up enable */ +#define PWER_GPIO10 PWER_GPIO (10) /* GPIO [10] wake-up enable */ +#define PWER_GPIO11 PWER_GPIO (11) /* GPIO [11] wake-up enable */ +#define PWER_GPIO12 PWER_GPIO (12) /* GPIO [12] wake-up enable */ +#define PWER_GPIO13 PWER_GPIO (13) /* GPIO [13] wake-up enable */ +#define PWER_GPIO14 PWER_GPIO (14) /* GPIO [14] wake-up enable */ +#define PWER_GPIO15 PWER_GPIO (15) /* GPIO [15] wake-up enable */ +#define PWER_RTC 0x80000000 /* RTC alarm wake-up enable */ + +/* + * PXA2xx specific Core clock definitions + */ +#define CCCR io_p2v(0x41300000) /* Core Clock Configuration Register */ +#define CCSR io_p2v(0x4130000C) /* Core Clock Status Register */ +#define CKEN io_p2v(0x41300004) /* Clock Enable Register */ +#define OSCC io_p2v(0x41300008) /* Oscillator Configuration Register */ + +#define CCCR_N_MASK 0x0380 /* Run Mode Frequency to Turbo Mode Frequency Multiplier */ +#define CCCR_M_MASK 0x0060 /* Memory Frequency to Run Mode Frequency Multiplier */ +#define CCCR_L_MASK 0x001f /* Crystal Frequency to Memory Frequency Multiplier */ + +#define CCCR_CPDIS_BIT (31) +#define CCCR_PPDIS_BIT (30) +#define CCCR_LCD_26_BIT (27) +#define CCCR_A_BIT (25) + +#define CCSR_N2_MASK CCCR_N_MASK +#define CCSR_M_MASK CCCR_M_MASK +#define CCSR_L_MASK CCCR_L_MASK +#define CCSR_N2_SHIFT 7 + +#define CKEN_AC97CONF (31) /* AC97 Controller Configuration */ +#define CKEN_CAMERA (24) /* Camera Interface Clock Enable */ +#define CKEN_SSP1 (23) /* SSP1 Unit Clock Enable */ +#define CKEN_MEMC (22) /* Memory Controller Clock Enable */ +#define CKEN_MEMSTK (21) /* Memory Stick Host Controller */ +#define CKEN_IM (20) /* Internal Memory Clock Enable */ +#define CKEN_KEYPAD (19) /* Keypad Interface Clock Enable */ +#define CKEN_USIM (18) /* USIM Unit Clock Enable */ +#define CKEN_MSL (17) /* MSL Unit Clock Enable */ +#define CKEN_LCD (16) /* LCD Unit Clock Enable */ +#define CKEN_PWRI2C (15) /* PWR I2C Unit Clock Enable */ +#define CKEN_I2C (14) /* I2C Unit Clock Enable */ +#define CKEN_FICP (13) /* FICP Unit Clock Enable */ +#define CKEN_MMC (12) /* MMC Unit Clock Enable */ +#define CKEN_USB (11) /* USB Unit Clock Enable */ +#define CKEN_ASSP (10) /* ASSP (SSP3) Clock Enable */ +#define CKEN_USBHOST (10) /* USB Host Unit Clock Enable */ +#define CKEN_OSTIMER (9) /* OS Timer Unit Clock Enable */ +#define CKEN_NSSP (9) /* NSSP (SSP2) Clock Enable */ +#define CKEN_I2S (8) /* I2S Unit Clock Enable */ +#define CKEN_BTUART (7) /* BTUART Unit Clock Enable */ +#define CKEN_FFUART (6) /* FFUART Unit Clock Enable */ +#define CKEN_STUART (5) /* STUART Unit Clock Enable */ +#define CKEN_HWUART (4) /* HWUART Unit Clock Enable */ +#define CKEN_SSP3 (4) /* SSP3 Unit Clock Enable */ +#define CKEN_SSP (3) /* SSP Unit Clock Enable */ +#define CKEN_SSP2 (3) /* SSP2 Unit Clock Enable */ +#define CKEN_AC97 (2) /* AC97 Unit Clock Enable */ +#define CKEN_PWM1 (1) /* PWM1 Clock Enable */ +#define CKEN_PWM0 (0) /* PWM0 Clock Enable */ + +#define OSCC_OON (1 << 1) /* 32.768kHz OON (write-once only bit) */ +#define OSCC_OOK (1 << 0) /* 32.768kHz OOK (read-only bit) */ + +/* PWRMODE register M field values */ + +#define PWRMODE_IDLE 0x1 +#define PWRMODE_STANDBY 0x2 +#define PWRMODE_SLEEP 0x3 +#define PWRMODE_DEEPSLEEP 0x7 + +#endif diff --git a/arch/arm/mach-pxa/include/mach/pxa3xx-regs.h b/arch/arm/mach-pxa/include/mach/pxa3xx-regs.h new file mode 100644 index 000000000..070f6c741 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/pxa3xx-regs.h @@ -0,0 +1,203 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ +/* + * arch/arm/mach-pxa/include/mach/pxa3xx-regs.h + * + * PXA3xx specific register definitions + * + * Copyright (C) 2007 Marvell International Ltd. + */ + +#ifndef __ASM_ARCH_PXA3XX_REGS_H +#define __ASM_ARCH_PXA3XX_REGS_H + +#include <mach/hardware.h> + +/* + * Oscillator Configuration Register (OSCC) + */ +#define OSCC io_p2v(0x41350000) /* Oscillator Configuration Register */ + +#define OSCC_PEN (1 << 11) /* 13MHz POUT */ + + +/* + * Service Power Management Unit (MPMU) + */ +#define PMCR __REG(0x40F50000) /* Power Manager Control Register */ +#define PSR __REG(0x40F50004) /* Power Manager S2 Status Register */ +#define PSPR __REG(0x40F50008) /* Power Manager Scratch Pad Register */ +#define PCFR __REG(0x40F5000C) /* Power Manager General Configuration Register */ +#define PWER __REG(0x40F50010) /* Power Manager Wake-up Enable Register */ +#define PWSR __REG(0x40F50014) /* Power Manager Wake-up Status Register */ +#define PECR __REG(0x40F50018) /* Power Manager EXT_WAKEUP[1:0] Control Register */ +#define DCDCSR __REG(0x40F50080) /* DC-DC Controller Status Register */ +#define PVCR __REG(0x40F50100) /* Power Manager Voltage Change Control Register */ +#define PCMD(x) __REG(0x40F50110 + ((x) << 2)) + +/* + * Slave Power Management Unit + */ +#define ASCR __REG(0x40f40000) /* Application Subsystem Power Status/Configuration */ +#define ARSR __REG(0x40f40004) /* Application Subsystem Reset Status */ +#define AD3ER __REG(0x40f40008) /* Application Subsystem Wake-Up from D3 Enable */ +#define AD3SR __REG(0x40f4000c) /* Application Subsystem Wake-Up from D3 Status */ +#define AD2D0ER __REG(0x40f40010) /* Application Subsystem Wake-Up from D2 to D0 Enable */ +#define AD2D0SR __REG(0x40f40014) /* Application Subsystem Wake-Up from D2 to D0 Status */ +#define AD2D1ER __REG(0x40f40018) /* Application Subsystem Wake-Up from D2 to D1 Enable */ +#define AD2D1SR __REG(0x40f4001c) /* Application Subsystem Wake-Up from D2 to D1 Status */ +#define AD1D0ER __REG(0x40f40020) /* Application Subsystem Wake-Up from D1 to D0 Enable */ +#define AD1D0SR __REG(0x40f40024) /* Application Subsystem Wake-Up from D1 to D0 Status */ +#define AGENP __REG(0x40f4002c) /* Application Subsystem General Purpose */ +#define AD3R __REG(0x40f40030) /* Application Subsystem D3 Configuration */ +#define AD2R __REG(0x40f40034) /* Application Subsystem D2 Configuration */ +#define AD1R __REG(0x40f40038) /* Application Subsystem D1 Configuration */ + +/* + * Application Subsystem Configuration bits. + */ +#define ASCR_RDH (1 << 31) +#define ASCR_D1S (1 << 2) +#define ASCR_D2S (1 << 1) +#define ASCR_D3S (1 << 0) + +/* + * Application Reset Status bits. + */ +#define ARSR_GPR (1 << 3) +#define ARSR_LPMR (1 << 2) +#define ARSR_WDT (1 << 1) +#define ARSR_HWR (1 << 0) + +/* + * Application Subsystem Wake-Up bits. + */ +#define ADXER_WRTC (1 << 31) /* RTC */ +#define ADXER_WOST (1 << 30) /* OS Timer */ +#define ADXER_WTSI (1 << 29) /* Touchscreen */ +#define ADXER_WUSBH (1 << 28) /* USB host */ +#define ADXER_WUSB2 (1 << 26) /* USB client 2.0 */ +#define ADXER_WMSL0 (1 << 24) /* MSL port 0*/ +#define ADXER_WDMUX3 (1 << 23) /* USB EDMUX3 */ +#define ADXER_WDMUX2 (1 << 22) /* USB EDMUX2 */ +#define ADXER_WKP (1 << 21) /* Keypad */ +#define ADXER_WUSIM1 (1 << 20) /* USIM Port 1 */ +#define ADXER_WUSIM0 (1 << 19) /* USIM Port 0 */ +#define ADXER_WOTG (1 << 16) /* USBOTG input */ +#define ADXER_MFP_WFLASH (1 << 15) /* MFP: Data flash busy */ +#define ADXER_MFP_GEN12 (1 << 14) /* MFP: MMC3/GPIO/OST inputs */ +#define ADXER_MFP_WMMC2 (1 << 13) /* MFP: MMC2 */ +#define ADXER_MFP_WMMC1 (1 << 12) /* MFP: MMC1 */ +#define ADXER_MFP_WI2C (1 << 11) /* MFP: I2C */ +#define ADXER_MFP_WSSP4 (1 << 10) /* MFP: SSP4 */ +#define ADXER_MFP_WSSP3 (1 << 9) /* MFP: SSP3 */ +#define ADXER_MFP_WMAXTRIX (1 << 8) /* MFP: matrix keypad */ +#define ADXER_MFP_WUART3 (1 << 7) /* MFP: UART3 */ +#define ADXER_MFP_WUART2 (1 << 6) /* MFP: UART2 */ +#define ADXER_MFP_WUART1 (1 << 5) /* MFP: UART1 */ +#define ADXER_MFP_WSSP2 (1 << 4) /* MFP: SSP2 */ +#define ADXER_MFP_WSSP1 (1 << 3) /* MFP: SSP1 */ +#define ADXER_MFP_WAC97 (1 << 2) /* MFP: AC97 */ +#define ADXER_WEXTWAKE1 (1 << 1) /* External Wake 1 */ +#define ADXER_WEXTWAKE0 (1 << 0) /* External Wake 0 */ + +/* + * AD3R/AD2R/AD1R bits. R2-R5 are only defined for PXA320. + */ +#define ADXR_L2 (1 << 8) +#define ADXR_R5 (1 << 5) +#define ADXR_R4 (1 << 4) +#define ADXR_R3 (1 << 3) +#define ADXR_R2 (1 << 2) +#define ADXR_R1 (1 << 1) +#define ADXR_R0 (1 << 0) + +/* + * Values for PWRMODE CP15 register + */ +#define PXA3xx_PM_S3D4C4 0x07 /* aka deep sleep */ +#define PXA3xx_PM_S2D3C4 0x06 /* aka sleep */ +#define PXA3xx_PM_S0D2C2 0x03 /* aka standby */ +#define PXA3xx_PM_S0D1C2 0x02 /* aka LCD refresh */ +#define PXA3xx_PM_S0D0C1 0x01 + +/* + * Application Subsystem Clock + */ +#define ACCR __REG(0x41340000) /* Application Subsystem Clock Configuration Register */ +#define ACSR __REG(0x41340004) /* Application Subsystem Clock Status Register */ +#define AICSR __REG(0x41340008) /* Application Subsystem Interrupt Control/Status Register */ +#define CKENA __REG(0x4134000C) /* A Clock Enable Register */ +#define CKENB __REG(0x41340010) /* B Clock Enable Register */ +#define CKENC __REG(0x41340024) /* C Clock Enable Register */ +#define AC97_DIV __REG(0x41340014) /* AC97 clock divisor value register */ + +#define ACCR_XPDIS (1 << 31) /* Core PLL Output Disable */ +#define ACCR_SPDIS (1 << 30) /* System PLL Output Disable */ +#define ACCR_D0CS (1 << 26) /* D0 Mode Clock Select */ +#define ACCR_PCCE (1 << 11) /* Power Mode Change Clock Enable */ +#define ACCR_DDR_D0CS (1 << 7) /* DDR SDRAM clock frequency in D0CS (PXA31x only) */ + +#define ACCR_SMCFS_MASK (0x7 << 23) /* Static Memory Controller Frequency Select */ +#define ACCR_SFLFS_MASK (0x3 << 18) /* Frequency Select for Internal Memory Controller */ +#define ACCR_XSPCLK_MASK (0x3 << 16) /* Core Frequency during Frequency Change */ +#define ACCR_HSS_MASK (0x3 << 14) /* System Bus-Clock Frequency Select */ +#define ACCR_DMCFS_MASK (0x3 << 12) /* Dynamic Memory Controller Clock Frequency Select */ +#define ACCR_XN_MASK (0x7 << 8) /* Core PLL Turbo-Mode-to-Run-Mode Ratio */ +#define ACCR_XL_MASK (0x1f) /* Core PLL Run-Mode-to-Oscillator Ratio */ + +#define ACCR_SMCFS(x) (((x) & 0x7) << 23) +#define ACCR_SFLFS(x) (((x) & 0x3) << 18) +#define ACCR_XSPCLK(x) (((x) & 0x3) << 16) +#define ACCR_HSS(x) (((x) & 0x3) << 14) +#define ACCR_DMCFS(x) (((x) & 0x3) << 12) +#define ACCR_XN(x) (((x) & 0x7) << 8) +#define ACCR_XL(x) ((x) & 0x1f) + +/* + * Clock Enable Bit + */ +#define CKEN_LCD 1 /* < LCD Clock Enable */ +#define CKEN_USBH 2 /* < USB host clock enable */ +#define CKEN_CAMERA 3 /* < Camera interface clock enable */ +#define CKEN_NAND 4 /* < NAND Flash Controller Clock Enable */ +#define CKEN_USB2 6 /* < USB 2.0 client clock enable. */ +#define CKEN_DMC 8 /* < Dynamic Memory Controller clock enable */ +#define CKEN_SMC 9 /* < Static Memory Controller clock enable */ +#define CKEN_ISC 10 /* < Internal SRAM Controller clock enable */ +#define CKEN_BOOT 11 /* < Boot rom clock enable */ +#define CKEN_MMC1 12 /* < MMC1 Clock enable */ +#define CKEN_MMC2 13 /* < MMC2 clock enable */ +#define CKEN_KEYPAD 14 /* < Keypand Controller Clock Enable */ +#define CKEN_CIR 15 /* < Consumer IR Clock Enable */ +#define CKEN_USIM0 17 /* < USIM[0] Clock Enable */ +#define CKEN_USIM1 18 /* < USIM[1] Clock Enable */ +#define CKEN_TPM 19 /* < TPM clock enable */ +#define CKEN_UDC 20 /* < UDC clock enable */ +#define CKEN_BTUART 21 /* < BTUART clock enable */ +#define CKEN_FFUART 22 /* < FFUART clock enable */ +#define CKEN_STUART 23 /* < STUART clock enable */ +#define CKEN_AC97 24 /* < AC97 clock enable */ +#define CKEN_TOUCH 25 /* < Touch screen Interface Clock Enable */ +#define CKEN_SSP1 26 /* < SSP1 clock enable */ +#define CKEN_SSP2 27 /* < SSP2 clock enable */ +#define CKEN_SSP3 28 /* < SSP3 clock enable */ +#define CKEN_SSP4 29 /* < SSP4 clock enable */ +#define CKEN_MSL0 30 /* < MSL0 clock enable */ +#define CKEN_PWM0 32 /* < PWM[0] clock enable */ +#define CKEN_PWM1 33 /* < PWM[1] clock enable */ +#define CKEN_I2C 36 /* < I2C clock enable */ +#define CKEN_INTC 38 /* < Interrupt controller clock enable */ +#define CKEN_GPIO 39 /* < GPIO clock enable */ +#define CKEN_1WIRE 40 /* < 1-wire clock enable */ +#define CKEN_HSIO2 41 /* < HSIO2 clock enable */ +#define CKEN_MINI_IM 48 /* < Mini-IM */ +#define CKEN_MINI_LCD 49 /* < Mini LCD */ + +#define CKEN_MMC3 5 /* < MMC3 Clock Enable */ +#define CKEN_MVED 43 /* < MVED clock enable */ + +/* Note: GCU clock enable bit differs on PXA300/PXA310 and PXA320 */ +#define CKEN_PXA300_GCU 42 /* Graphics controller clock enable */ +#define CKEN_PXA320_GCU 7 /* Graphics controller clock enable */ + +#endif /* __ASM_ARCH_PXA3XX_REGS_H */ diff --git a/arch/arm/mach-pxa/include/mach/regs-ac97.h b/arch/arm/mach-pxa/include/mach/regs-ac97.h new file mode 100644 index 000000000..1db96fd4d --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/regs-ac97.h @@ -0,0 +1,102 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +#ifndef __ASM_ARCH_REGS_AC97_H +#define __ASM_ARCH_REGS_AC97_H + +#include <mach/hardware.h> + +/* + * AC97 Controller registers + */ + +#define POCR __REG(0x40500000) /* PCM Out Control Register */ +#define POCR_FEIE (1 << 3) /* FIFO Error Interrupt Enable */ +#define POCR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */ + +#define PICR __REG(0x40500004) /* PCM In Control Register */ +#define PICR_FEIE (1 << 3) /* FIFO Error Interrupt Enable */ +#define PICR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */ + +#define MCCR __REG(0x40500008) /* Mic In Control Register */ +#define MCCR_FEIE (1 << 3) /* FIFO Error Interrupt Enable */ +#define MCCR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */ + +#define GCR __REG(0x4050000C) /* Global Control Register */ +#ifdef CONFIG_PXA3xx +#define GCR_CLKBPB (1 << 31) /* Internal clock enable */ +#endif +#define GCR_nDMAEN (1 << 24) /* non DMA Enable */ +#define GCR_CDONE_IE (1 << 19) /* Command Done Interrupt Enable */ +#define GCR_SDONE_IE (1 << 18) /* Status Done Interrupt Enable */ +#define GCR_SECRDY_IEN (1 << 9) /* Secondary Ready Interrupt Enable */ +#define GCR_PRIRDY_IEN (1 << 8) /* Primary Ready Interrupt Enable */ +#define GCR_SECRES_IEN (1 << 5) /* Secondary Resume Interrupt Enable */ +#define GCR_PRIRES_IEN (1 << 4) /* Primary Resume Interrupt Enable */ +#define GCR_ACLINK_OFF (1 << 3) /* AC-link Shut Off */ +#define GCR_WARM_RST (1 << 2) /* AC97 Warm Reset */ +#define GCR_COLD_RST (1 << 1) /* AC'97 Cold Reset (0 = active) */ +#define GCR_GIE (1 << 0) /* Codec GPI Interrupt Enable */ + +#define POSR __REG(0x40500010) /* PCM Out Status Register */ +#define POSR_FIFOE (1 << 4) /* FIFO error */ +#define POSR_FSR (1 << 2) /* FIFO Service Request */ + +#define PISR __REG(0x40500014) /* PCM In Status Register */ +#define PISR_FIFOE (1 << 4) /* FIFO error */ +#define PISR_EOC (1 << 3) /* DMA End-of-Chain (exclusive clear) */ +#define PISR_FSR (1 << 2) /* FIFO Service Request */ + +#define MCSR __REG(0x40500018) /* Mic In Status Register */ +#define MCSR_FIFOE (1 << 4) /* FIFO error */ +#define MCSR_EOC (1 << 3) /* DMA End-of-Chain (exclusive clear) */ +#define MCSR_FSR (1 << 2) /* FIFO Service Request */ + +#define GSR __REG(0x4050001C) /* Global Status Register */ +#define GSR_CDONE (1 << 19) /* Command Done */ +#define GSR_SDONE (1 << 18) /* Status Done */ +#define GSR_RDCS (1 << 15) /* Read Completion Status */ +#define GSR_BIT3SLT12 (1 << 14) /* Bit 3 of slot 12 */ +#define GSR_BIT2SLT12 (1 << 13) /* Bit 2 of slot 12 */ +#define GSR_BIT1SLT12 (1 << 12) /* Bit 1 of slot 12 */ +#define GSR_SECRES (1 << 11) /* Secondary Resume Interrupt */ +#define GSR_PRIRES (1 << 10) /* Primary Resume Interrupt */ +#define GSR_SCR (1 << 9) /* Secondary Codec Ready */ +#define GSR_PCR (1 << 8) /* Primary Codec Ready */ +#define GSR_MCINT (1 << 7) /* Mic In Interrupt */ +#define GSR_POINT (1 << 6) /* PCM Out Interrupt */ +#define GSR_PIINT (1 << 5) /* PCM In Interrupt */ +#define GSR_ACOFFD (1 << 3) /* AC-link Shut Off Done */ +#define GSR_MOINT (1 << 2) /* Modem Out Interrupt */ +#define GSR_MIINT (1 << 1) /* Modem In Interrupt */ +#define GSR_GSCI (1 << 0) /* Codec GPI Status Change Interrupt */ + +#define CAR __REG(0x40500020) /* CODEC Access Register */ +#define CAR_CAIP (1 << 0) /* Codec Access In Progress */ + +#define PCDR __REG(0x40500040) /* PCM FIFO Data Register */ +#define MCDR __REG(0x40500060) /* Mic-in FIFO Data Register */ + +#define MOCR __REG(0x40500100) /* Modem Out Control Register */ +#define MOCR_FEIE (1 << 3) /* FIFO Error */ +#define MOCR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */ + +#define MICR __REG(0x40500108) /* Modem In Control Register */ +#define MICR_FEIE (1 << 3) /* FIFO Error */ +#define MICR_FSRIE (1 << 1) /* FIFO Service Request Interrupt Enable */ + +#define MOSR __REG(0x40500110) /* Modem Out Status Register */ +#define MOSR_FIFOE (1 << 4) /* FIFO error */ +#define MOSR_FSR (1 << 2) /* FIFO Service Request */ + +#define MISR __REG(0x40500118) /* Modem In Status Register */ +#define MISR_FIFOE (1 << 4) /* FIFO error */ +#define MISR_EOC (1 << 3) /* DMA End-of-Chain (exclusive clear) */ +#define MISR_FSR (1 << 2) /* FIFO Service Request */ + +#define MODR __REG(0x40500140) /* Modem FIFO Data Register */ + +#define PAC_REG_BASE __REG(0x40500200) /* Primary Audio Codec */ +#define SAC_REG_BASE __REG(0x40500300) /* Secondary Audio Codec */ +#define PMC_REG_BASE __REG(0x40500400) /* Primary Modem Codec */ +#define SMC_REG_BASE __REG(0x40500500) /* Secondary Modem Codec */ + +#endif /* __ASM_ARCH_REGS_AC97_H */ diff --git a/arch/arm/mach-pxa/include/mach/regs-lcd.h b/arch/arm/mach-pxa/include/mach/regs-lcd.h new file mode 100644 index 000000000..e2b6e3d1f --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/regs-lcd.h @@ -0,0 +1,198 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +#ifndef __ASM_ARCH_REGS_LCD_H +#define __ASM_ARCH_REGS_LCD_H + +#include <mach/bitfield.h> + +/* + * LCD Controller Registers and Bits Definitions + */ +#define LCCR0 (0x000) /* LCD Controller Control Register 0 */ +#define LCCR1 (0x004) /* LCD Controller Control Register 1 */ +#define LCCR2 (0x008) /* LCD Controller Control Register 2 */ +#define LCCR3 (0x00C) /* LCD Controller Control Register 3 */ +#define LCCR4 (0x010) /* LCD Controller Control Register 4 */ +#define LCCR5 (0x014) /* LCD Controller Control Register 5 */ +#define LCSR (0x038) /* LCD Controller Status Register 0 */ +#define LCSR1 (0x034) /* LCD Controller Status Register 1 */ +#define LIIDR (0x03C) /* LCD Controller Interrupt ID Register */ +#define TMEDRGBR (0x040) /* TMED RGB Seed Register */ +#define TMEDCR (0x044) /* TMED Control Register */ + +#define FBR0 (0x020) /* DMA Channel 0 Frame Branch Register */ +#define FBR1 (0x024) /* DMA Channel 1 Frame Branch Register */ +#define FBR2 (0x028) /* DMA Channel 2 Frame Branch Register */ +#define FBR3 (0x02C) /* DMA Channel 2 Frame Branch Register */ +#define FBR4 (0x030) /* DMA Channel 2 Frame Branch Register */ +#define FBR5 (0x110) /* DMA Channel 2 Frame Branch Register */ +#define FBR6 (0x114) /* DMA Channel 2 Frame Branch Register */ + +#define OVL1C1 (0x050) /* Overlay 1 Control Register 1 */ +#define OVL1C2 (0x060) /* Overlay 1 Control Register 2 */ +#define OVL2C1 (0x070) /* Overlay 2 Control Register 1 */ +#define OVL2C2 (0x080) /* Overlay 2 Control Register 2 */ + +#define CMDCR (0x100) /* Command Control Register */ +#define PRSR (0x104) /* Panel Read Status Register */ + +#define LCCR3_BPP(x) ((((x) & 0x7) << 24) | (((x) & 0x8) ? (1 << 29) : 0)) + +#define LCCR3_PDFOR_0 (0 << 30) +#define LCCR3_PDFOR_1 (1 << 30) +#define LCCR3_PDFOR_2 (2 << 30) +#define LCCR3_PDFOR_3 (3 << 30) + +#define LCCR4_PAL_FOR_0 (0 << 15) +#define LCCR4_PAL_FOR_1 (1 << 15) +#define LCCR4_PAL_FOR_2 (2 << 15) +#define LCCR4_PAL_FOR_3 (3 << 15) +#define LCCR4_PAL_FOR_MASK (3 << 15) + +#define FDADR0 (0x200) /* DMA Channel 0 Frame Descriptor Address Register */ +#define FDADR1 (0x210) /* DMA Channel 1 Frame Descriptor Address Register */ +#define FDADR2 (0x220) /* DMA Channel 2 Frame Descriptor Address Register */ +#define FDADR3 (0x230) /* DMA Channel 3 Frame Descriptor Address Register */ +#define FDADR4 (0x240) /* DMA Channel 4 Frame Descriptor Address Register */ +#define FDADR5 (0x250) /* DMA Channel 5 Frame Descriptor Address Register */ +#define FDADR6 (0x260) /* DMA Channel 6 Frame Descriptor Address Register */ + +#define LCCR0_ENB (1 << 0) /* LCD Controller enable */ +#define LCCR0_CMS (1 << 1) /* Color/Monochrome Display Select */ +#define LCCR0_Color (LCCR0_CMS*0) /* Color display */ +#define LCCR0_Mono (LCCR0_CMS*1) /* Monochrome display */ +#define LCCR0_SDS (1 << 2) /* Single/Dual Panel Display Select */ +#define LCCR0_Sngl (LCCR0_SDS*0) /* Single panel display */ +#define LCCR0_Dual (LCCR0_SDS*1) /* Dual panel display */ + +#define LCCR0_LDM (1 << 3) /* LCD Disable Done Mask */ +#define LCCR0_SFM (1 << 4) /* Start of frame mask */ +#define LCCR0_IUM (1 << 5) /* Input FIFO underrun mask */ +#define LCCR0_EFM (1 << 6) /* End of Frame mask */ +#define LCCR0_PAS (1 << 7) /* Passive/Active display Select */ +#define LCCR0_Pas (LCCR0_PAS*0) /* Passive display (STN) */ +#define LCCR0_Act (LCCR0_PAS*1) /* Active display (TFT) */ +#define LCCR0_DPD (1 << 9) /* Double Pixel Data (monochrome) */ +#define LCCR0_4PixMono (LCCR0_DPD*0) /* 4-Pixel/clock Monochrome display */ +#define LCCR0_8PixMono (LCCR0_DPD*1) /* 8-Pixel/clock Monochrome display */ +#define LCCR0_DIS (1 << 10) /* LCD Disable */ +#define LCCR0_QDM (1 << 11) /* LCD Quick Disable mask */ +#define LCCR0_PDD (0xff << 12) /* Palette DMA request delay */ +#define LCCR0_PDD_S 12 +#define LCCR0_BM (1 << 20) /* Branch mask */ +#define LCCR0_OUM (1 << 21) /* Output FIFO underrun mask */ +#define LCCR0_LCDT (1 << 22) /* LCD panel type */ +#define LCCR0_RDSTM (1 << 23) /* Read status interrupt mask */ +#define LCCR0_CMDIM (1 << 24) /* Command interrupt mask */ +#define LCCR0_OUC (1 << 25) /* Overlay Underlay control bit */ +#define LCCR0_LDDALT (1 << 26) /* LDD alternate mapping control */ + +#define LCCR1_PPL Fld (10, 0) /* Pixels Per Line - 1 */ +#define LCCR1_DisWdth(Pixel) (((Pixel) - 1) << FShft (LCCR1_PPL)) + +#define LCCR1_HSW Fld (6, 10) /* Horizontal Synchronization */ +#define LCCR1_HorSnchWdth(Tpix) (((Tpix) - 1) << FShft (LCCR1_HSW)) + +#define LCCR1_ELW Fld (8, 16) /* End-of-Line pixel clock Wait - 1 */ +#define LCCR1_EndLnDel(Tpix) (((Tpix) - 1) << FShft (LCCR1_ELW)) + +#define LCCR1_BLW Fld (8, 24) /* Beginning-of-Line pixel clock */ +#define LCCR1_BegLnDel(Tpix) (((Tpix) - 1) << FShft (LCCR1_BLW)) + +#define LCCR2_LPP Fld (10, 0) /* Line Per Panel - 1 */ +#define LCCR2_DisHght(Line) (((Line) - 1) << FShft (LCCR2_LPP)) + +#define LCCR2_VSW Fld (6, 10) /* Vertical Synchronization pulse - 1 */ +#define LCCR2_VrtSnchWdth(Tln) (((Tln) - 1) << FShft (LCCR2_VSW)) + +#define LCCR2_EFW Fld (8, 16) /* End-of-Frame line clock Wait */ +#define LCCR2_EndFrmDel(Tln) ((Tln) << FShft (LCCR2_EFW)) + +#define LCCR2_BFW Fld (8, 24) /* Beginning-of-Frame line clock */ +#define LCCR2_BegFrmDel(Tln) ((Tln) << FShft (LCCR2_BFW)) + +#define LCCR3_API (0xf << 16) /* AC Bias pin trasitions per interrupt */ +#define LCCR3_API_S 16 +#define LCCR3_VSP (1 << 20) /* vertical sync polarity */ +#define LCCR3_HSP (1 << 21) /* horizontal sync polarity */ +#define LCCR3_PCP (1 << 22) /* Pixel Clock Polarity (L_PCLK) */ +#define LCCR3_PixRsEdg (LCCR3_PCP*0) /* Pixel clock Rising-Edge */ +#define LCCR3_PixFlEdg (LCCR3_PCP*1) /* Pixel clock Falling-Edge */ + +#define LCCR3_OEP (1 << 23) /* Output Enable Polarity */ +#define LCCR3_OutEnH (LCCR3_OEP*0) /* Output Enable active High */ +#define LCCR3_OutEnL (LCCR3_OEP*1) /* Output Enable active Low */ + +#define LCCR3_DPC (1 << 27) /* double pixel clock mode */ +#define LCCR3_PCD Fld (8, 0) /* Pixel Clock Divisor */ +#define LCCR3_PixClkDiv(Div) (((Div) << FShft (LCCR3_PCD))) + +#define LCCR3_ACB Fld (8, 8) /* AC Bias */ +#define LCCR3_Acb(Acb) (((Acb) << FShft (LCCR3_ACB))) + +#define LCCR3_HorSnchH (LCCR3_HSP*0) /* HSP Active High */ +#define LCCR3_HorSnchL (LCCR3_HSP*1) /* HSP Active Low */ + +#define LCCR3_VrtSnchH (LCCR3_VSP*0) /* VSP Active High */ +#define LCCR3_VrtSnchL (LCCR3_VSP*1) /* VSP Active Low */ + +#define LCCR5_IUM(x) (1 << ((x) + 23)) /* input underrun mask */ +#define LCCR5_BSM(x) (1 << ((x) + 15)) /* branch mask */ +#define LCCR5_EOFM(x) (1 << ((x) + 7)) /* end of frame mask */ +#define LCCR5_SOFM(x) (1 << ((x) + 0)) /* start of frame mask */ + +#define LCSR_LDD (1 << 0) /* LCD Disable Done */ +#define LCSR_SOF (1 << 1) /* Start of frame */ +#define LCSR_BER (1 << 2) /* Bus error */ +#define LCSR_ABC (1 << 3) /* AC Bias count */ +#define LCSR_IUL (1 << 4) /* input FIFO underrun Lower panel */ +#define LCSR_IUU (1 << 5) /* input FIFO underrun Upper panel */ +#define LCSR_OU (1 << 6) /* output FIFO underrun */ +#define LCSR_QD (1 << 7) /* quick disable */ +#define LCSR_EOF (1 << 8) /* end of frame */ +#define LCSR_BS (1 << 9) /* branch status */ +#define LCSR_SINT (1 << 10) /* subsequent interrupt */ +#define LCSR_RD_ST (1 << 11) /* read status */ +#define LCSR_CMD_INT (1 << 12) /* command interrupt */ + +#define LCSR1_IU(x) (1 << ((x) + 23)) /* Input FIFO underrun */ +#define LCSR1_BS(x) (1 << ((x) + 15)) /* Branch Status */ +#define LCSR1_EOF(x) (1 << ((x) + 7)) /* End of Frame Status */ +#define LCSR1_SOF(x) (1 << ((x) - 1)) /* Start of Frame Status */ + +#define LDCMD_PAL (1 << 26) /* instructs DMA to load palette buffer */ + +/* overlay control registers */ +#define OVLxC1_PPL(x) ((((x) - 1) & 0x3ff) << 0) /* Pixels Per Line */ +#define OVLxC1_LPO(x) ((((x) - 1) & 0x3ff) << 10) /* Number of Lines */ +#define OVLxC1_BPP(x) (((x) & 0xf) << 20) /* Bits Per Pixel */ +#define OVLxC1_OEN (1 << 31) /* Enable bit for Overlay */ +#define OVLxC2_XPOS(x) (((x) & 0x3ff) << 0) /* Horizontal Position */ +#define OVLxC2_YPOS(x) (((x) & 0x3ff) << 10) /* Vertical Position */ +#define OVL2C2_PFOR(x) (((x) & 0x7) << 20) /* Pixel Format */ + +/* smartpanel related */ +#define PRSR_DATA(x) ((x) & 0xff) /* Panel Data */ +#define PRSR_A0 (1 << 8) /* Read Data Source */ +#define PRSR_ST_OK (1 << 9) /* Status OK */ +#define PRSR_CON_NT (1 << 10) /* Continue to Next Command */ + +#define SMART_CMD_A0 (0x1 << 8) +#define SMART_CMD_READ_STATUS_REG (0x0 << 9) +#define SMART_CMD_READ_FRAME_BUFFER ((0x0 << 9) | SMART_CMD_A0) +#define SMART_CMD_WRITE_COMMAND (0x1 << 9) +#define SMART_CMD_WRITE_DATA ((0x1 << 9) | SMART_CMD_A0) +#define SMART_CMD_WRITE_FRAME ((0x2 << 9) | SMART_CMD_A0) +#define SMART_CMD_WAIT_FOR_VSYNC (0x3 << 9) +#define SMART_CMD_NOOP (0x4 << 9) +#define SMART_CMD_INTERRUPT (0x5 << 9) + +#define SMART_CMD(x) (SMART_CMD_WRITE_COMMAND | ((x) & 0xff)) +#define SMART_DAT(x) (SMART_CMD_WRITE_DATA | ((x) & 0xff)) + +/* SMART_DELAY() is introduced for software controlled delay primitive which + * can be inserted between command sequences, unused command 0x6 is used here + * and delay ranges from 0ms ~ 255ms + */ +#define SMART_CMD_DELAY (0x6 << 9) +#define SMART_DELAY(ms) (SMART_CMD_DELAY | ((ms) & 0xff)) +#endif /* __ASM_ARCH_REGS_LCD_H */ diff --git a/arch/arm/mach-pxa/include/mach/regs-ost.h b/arch/arm/mach-pxa/include/mach/regs-ost.h new file mode 100644 index 000000000..deb564ed8 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/regs-ost.h @@ -0,0 +1,35 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +#ifndef __ASM_MACH_REGS_OST_H +#define __ASM_MACH_REGS_OST_H + +#include <mach/hardware.h> + +/* + * OS Timer & Match Registers + */ + +#define OSMR0 io_p2v(0x40A00000) /* */ +#define OSMR1 io_p2v(0x40A00004) /* */ +#define OSMR2 io_p2v(0x40A00008) /* */ +#define OSMR3 io_p2v(0x40A0000C) /* */ +#define OSMR4 io_p2v(0x40A00080) /* */ +#define OSCR io_p2v(0x40A00010) /* OS Timer Counter Register */ +#define OSCR4 io_p2v(0x40A00040) /* OS Timer Counter Register */ +#define OMCR4 io_p2v(0x40A000C0) /* */ +#define OSSR io_p2v(0x40A00014) /* OS Timer Status Register */ +#define OWER io_p2v(0x40A00018) /* OS Timer Watchdog Enable Register */ +#define OIER io_p2v(0x40A0001C) /* OS Timer Interrupt Enable Register */ + +#define OSSR_M3 (1 << 3) /* Match status channel 3 */ +#define OSSR_M2 (1 << 2) /* Match status channel 2 */ +#define OSSR_M1 (1 << 1) /* Match status channel 1 */ +#define OSSR_M0 (1 << 0) /* Match status channel 0 */ + +#define OWER_WME (1 << 0) /* Watchdog Match Enable */ + +#define OIER_E3 (1 << 3) /* Interrupt enable channel 3 */ +#define OIER_E2 (1 << 2) /* Interrupt enable channel 2 */ +#define OIER_E1 (1 << 1) /* Interrupt enable channel 1 */ +#define OIER_E0 (1 << 0) /* Interrupt enable channel 0 */ + +#endif /* __ASM_MACH_REGS_OST_H */ diff --git a/arch/arm/mach-pxa/include/mach/regs-uart.h b/arch/arm/mach-pxa/include/mach/regs-uart.h new file mode 100644 index 000000000..9a168f83a --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/regs-uart.h @@ -0,0 +1,144 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +#ifndef __ASM_ARCH_REGS_UART_H +#define __ASM_ARCH_REGS_UART_H + +/* + * UARTs + */ + +/* Full Function UART (FFUART) */ +#define FFUART FFRBR +#define FFRBR __REG(0x40100000) /* Receive Buffer Register (read only) */ +#define FFTHR __REG(0x40100000) /* Transmit Holding Register (write only) */ +#define FFIER __REG(0x40100004) /* Interrupt Enable Register (read/write) */ +#define FFIIR __REG(0x40100008) /* Interrupt ID Register (read only) */ +#define FFFCR __REG(0x40100008) /* FIFO Control Register (write only) */ +#define FFLCR __REG(0x4010000C) /* Line Control Register (read/write) */ +#define FFMCR __REG(0x40100010) /* Modem Control Register (read/write) */ +#define FFLSR __REG(0x40100014) /* Line Status Register (read only) */ +#define FFMSR __REG(0x40100018) /* Modem Status Register (read only) */ +#define FFSPR __REG(0x4010001C) /* Scratch Pad Register (read/write) */ +#define FFISR __REG(0x40100020) /* Infrared Selection Register (read/write) */ +#define FFDLL __REG(0x40100000) /* Divisor Latch Low Register (DLAB = 1) (read/write) */ +#define FFDLH __REG(0x40100004) /* Divisor Latch High Register (DLAB = 1) (read/write) */ + +/* Bluetooth UART (BTUART) */ +#define BTUART BTRBR +#define BTRBR __REG(0x40200000) /* Receive Buffer Register (read only) */ +#define BTTHR __REG(0x40200000) /* Transmit Holding Register (write only) */ +#define BTIER __REG(0x40200004) /* Interrupt Enable Register (read/write) */ +#define BTIIR __REG(0x40200008) /* Interrupt ID Register (read only) */ +#define BTFCR __REG(0x40200008) /* FIFO Control Register (write only) */ +#define BTLCR __REG(0x4020000C) /* Line Control Register (read/write) */ +#define BTMCR __REG(0x40200010) /* Modem Control Register (read/write) */ +#define BTLSR __REG(0x40200014) /* Line Status Register (read only) */ +#define BTMSR __REG(0x40200018) /* Modem Status Register (read only) */ +#define BTSPR __REG(0x4020001C) /* Scratch Pad Register (read/write) */ +#define BTISR __REG(0x40200020) /* Infrared Selection Register (read/write) */ +#define BTDLL __REG(0x40200000) /* Divisor Latch Low Register (DLAB = 1) (read/write) */ +#define BTDLH __REG(0x40200004) /* Divisor Latch High Register (DLAB = 1) (read/write) */ + +/* Standard UART (STUART) */ +#define STUART STRBR +#define STRBR __REG(0x40700000) /* Receive Buffer Register (read only) */ +#define STTHR __REG(0x40700000) /* Transmit Holding Register (write only) */ +#define STIER __REG(0x40700004) /* Interrupt Enable Register (read/write) */ +#define STIIR __REG(0x40700008) /* Interrupt ID Register (read only) */ +#define STFCR __REG(0x40700008) /* FIFO Control Register (write only) */ +#define STLCR __REG(0x4070000C) /* Line Control Register (read/write) */ +#define STMCR __REG(0x40700010) /* Modem Control Register (read/write) */ +#define STLSR __REG(0x40700014) /* Line Status Register (read only) */ +#define STMSR __REG(0x40700018) /* Reserved */ +#define STSPR __REG(0x4070001C) /* Scratch Pad Register (read/write) */ +#define STISR __REG(0x40700020) /* Infrared Selection Register (read/write) */ +#define STDLL __REG(0x40700000) /* Divisor Latch Low Register (DLAB = 1) (read/write) */ +#define STDLH __REG(0x40700004) /* Divisor Latch High Register (DLAB = 1) (read/write) */ + +/* Hardware UART (HWUART) */ +#define HWUART HWRBR +#define HWRBR __REG(0x41600000) /* Receive Buffer Register (read only) */ +#define HWTHR __REG(0x41600000) /* Transmit Holding Register (write only) */ +#define HWIER __REG(0x41600004) /* Interrupt Enable Register (read/write) */ +#define HWIIR __REG(0x41600008) /* Interrupt ID Register (read only) */ +#define HWFCR __REG(0x41600008) /* FIFO Control Register (write only) */ +#define HWLCR __REG(0x4160000C) /* Line Control Register (read/write) */ +#define HWMCR __REG(0x41600010) /* Modem Control Register (read/write) */ +#define HWLSR __REG(0x41600014) /* Line Status Register (read only) */ +#define HWMSR __REG(0x41600018) /* Modem Status Register (read only) */ +#define HWSPR __REG(0x4160001C) /* Scratch Pad Register (read/write) */ +#define HWISR __REG(0x41600020) /* Infrared Selection Register (read/write) */ +#define HWFOR __REG(0x41600024) /* Receive FIFO Occupancy Register (read only) */ +#define HWABR __REG(0x41600028) /* Auto-Baud Control Register (read/write) */ +#define HWACR __REG(0x4160002C) /* Auto-Baud Count Register (read only) */ +#define HWDLL __REG(0x41600000) /* Divisor Latch Low Register (DLAB = 1) (read/write) */ +#define HWDLH __REG(0x41600004) /* Divisor Latch High Register (DLAB = 1) (read/write) */ + +#define IER_DMAE (1 << 7) /* DMA Requests Enable */ +#define IER_UUE (1 << 6) /* UART Unit Enable */ +#define IER_NRZE (1 << 5) /* NRZ coding Enable */ +#define IER_RTIOE (1 << 4) /* Receiver Time Out Interrupt Enable */ +#define IER_MIE (1 << 3) /* Modem Interrupt Enable */ +#define IER_RLSE (1 << 2) /* Receiver Line Status Interrupt Enable */ +#define IER_TIE (1 << 1) /* Transmit Data request Interrupt Enable */ +#define IER_RAVIE (1 << 0) /* Receiver Data Available Interrupt Enable */ + +#define IIR_FIFOES1 (1 << 7) /* FIFO Mode Enable Status */ +#define IIR_FIFOES0 (1 << 6) /* FIFO Mode Enable Status */ +#define IIR_TOD (1 << 3) /* Time Out Detected */ +#define IIR_IID2 (1 << 2) /* Interrupt Source Encoded */ +#define IIR_IID1 (1 << 1) /* Interrupt Source Encoded */ +#define IIR_IP (1 << 0) /* Interrupt Pending (active low) */ + +#define FCR_ITL2 (1 << 7) /* Interrupt Trigger Level */ +#define FCR_ITL1 (1 << 6) /* Interrupt Trigger Level */ +#define FCR_RESETTF (1 << 2) /* Reset Transmitter FIFO */ +#define FCR_RESETRF (1 << 1) /* Reset Receiver FIFO */ +#define FCR_TRFIFOE (1 << 0) /* Transmit and Receive FIFO Enable */ +#define FCR_ITL_1 (0) +#define FCR_ITL_8 (FCR_ITL1) +#define FCR_ITL_16 (FCR_ITL2) +#define FCR_ITL_32 (FCR_ITL2|FCR_ITL1) + +#define LCR_DLAB (1 << 7) /* Divisor Latch Access Bit */ +#define LCR_SB (1 << 6) /* Set Break */ +#define LCR_STKYP (1 << 5) /* Sticky Parity */ +#define LCR_EPS (1 << 4) /* Even Parity Select */ +#define LCR_PEN (1 << 3) /* Parity Enable */ +#define LCR_STB (1 << 2) /* Stop Bit */ +#define LCR_WLS1 (1 << 1) /* Word Length Select */ +#define LCR_WLS0 (1 << 0) /* Word Length Select */ + +#define LSR_FIFOE (1 << 7) /* FIFO Error Status */ +#define LSR_TEMT (1 << 6) /* Transmitter Empty */ +#define LSR_TDRQ (1 << 5) /* Transmit Data Request */ +#define LSR_BI (1 << 4) /* Break Interrupt */ +#define LSR_FE (1 << 3) /* Framing Error */ +#define LSR_PE (1 << 2) /* Parity Error */ +#define LSR_OE (1 << 1) /* Overrun Error */ +#define LSR_DR (1 << 0) /* Data Ready */ + +#define MCR_LOOP (1 << 4) +#define MCR_OUT2 (1 << 3) /* force MSR_DCD in loopback mode */ +#define MCR_OUT1 (1 << 2) /* force MSR_RI in loopback mode */ +#define MCR_RTS (1 << 1) /* Request to Send */ +#define MCR_DTR (1 << 0) /* Data Terminal Ready */ + +#define MSR_DCD (1 << 7) /* Data Carrier Detect */ +#define MSR_RI (1 << 6) /* Ring Indicator */ +#define MSR_DSR (1 << 5) /* Data Set Ready */ +#define MSR_CTS (1 << 4) /* Clear To Send */ +#define MSR_DDCD (1 << 3) /* Delta Data Carrier Detect */ +#define MSR_TERI (1 << 2) /* Trailing Edge Ring Indicator */ +#define MSR_DDSR (1 << 1) /* Delta Data Set Ready */ +#define MSR_DCTS (1 << 0) /* Delta Clear To Send */ + +/* + * IrSR (Infrared Selection Register) + */ +#define STISR_RXPL (1 << 4) /* Receive Data Polarity */ +#define STISR_TXPL (1 << 3) /* Transmit Data Polarity */ +#define STISR_XMODE (1 << 2) /* Transmit Pulse Width Select */ +#define STISR_RCVEIR (1 << 1) /* Receiver SIR Enable */ +#define STISR_XMITIR (1 << 0) /* Transmitter SIR Enable */ + +#endif /* __ASM_ARCH_REGS_UART_H */ diff --git a/arch/arm/mach-pxa/include/mach/reset.h b/arch/arm/mach-pxa/include/mach/reset.h new file mode 100644 index 000000000..e1c4d100f --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/reset.h @@ -0,0 +1,22 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +#ifndef __ASM_ARCH_RESET_H +#define __ASM_ARCH_RESET_H + +#define RESET_STATUS_HARDWARE (1 << 0) /* Hardware Reset */ +#define RESET_STATUS_WATCHDOG (1 << 1) /* Watchdog Reset */ +#define RESET_STATUS_LOWPOWER (1 << 2) /* Low Power/Sleep Exit */ +#define RESET_STATUS_GPIO (1 << 3) /* GPIO Reset */ +#define RESET_STATUS_ALL (0xf) + +extern unsigned int reset_status; +extern void clear_reset_status(unsigned int mask); + +/** + * init_gpio_reset() - register GPIO as reset generator + * @gpio: gpio nr + * @output: set gpio as output instead of input during normal work + * @level: output level + */ +extern int init_gpio_reset(int gpio, int output, int level); + +#endif /* __ASM_ARCH_RESET_H */ diff --git a/arch/arm/mach-pxa/include/mach/smemc.h b/arch/arm/mach-pxa/include/mach/smemc.h new file mode 100644 index 000000000..9b2453a7a --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/smemc.h @@ -0,0 +1,72 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ +/* + * Static memory controller register definitions for PXA CPUs + * + * Copyright (C) 2010 Marek Vasut <marek.vasut@gmail.com> + */ + +#ifndef __SMEMC_REGS_H +#define __SMEMC_REGS_H + +#define PXA2XX_SMEMC_BASE 0x48000000 +#define PXA3XX_SMEMC_BASE 0x4a000000 +#define SMEMC_VIRT IOMEM(0xf6000000) + +#define MDCNFG (SMEMC_VIRT + 0x00) /* SDRAM Configuration Register 0 */ +#define MDREFR (SMEMC_VIRT + 0x04) /* SDRAM Refresh Control Register */ +#define MSC0 (SMEMC_VIRT + 0x08) /* Static Memory Control Register 0 */ +#define MSC1 (SMEMC_VIRT + 0x0C) /* Static Memory Control Register 1 */ +#define MSC2 (SMEMC_VIRT + 0x10) /* Static Memory Control Register 2 */ +#define MECR (SMEMC_VIRT + 0x14) /* Expansion Memory (PCMCIA/Compact Flash) Bus Configuration */ +#define SXLCR (SMEMC_VIRT + 0x18) /* LCR value to be written to SDRAM-Timing Synchronous Flash */ +#define SXCNFG (SMEMC_VIRT + 0x1C) /* Synchronous Static Memory Control Register */ +#define SXMRS (SMEMC_VIRT + 0x24) /* MRS value to be written to Synchronous Flash or SMROM */ +#define MCMEM0 (SMEMC_VIRT + 0x28) /* Card interface Common Memory Space Socket 0 Timing */ +#define MCMEM1 (SMEMC_VIRT + 0x2C) /* Card interface Common Memory Space Socket 1 Timing */ +#define MCATT0 (SMEMC_VIRT + 0x30) /* Card interface Attribute Space Socket 0 Timing Configuration */ +#define MCATT1 (SMEMC_VIRT + 0x34) /* Card interface Attribute Space Socket 1 Timing Configuration */ +#define MCIO0 (SMEMC_VIRT + 0x38) /* Card interface I/O Space Socket 0 Timing Configuration */ +#define MCIO1 (SMEMC_VIRT + 0x3C) /* Card interface I/O Space Socket 1 Timing Configuration */ +#define MDMRS (SMEMC_VIRT + 0x40) /* MRS value to be written to SDRAM */ +#define BOOT_DEF (SMEMC_VIRT + 0x44) /* Read-Only Boot-Time Register. Contains BOOT_SEL and PKG_SEL */ +#define MEMCLKCFG (SMEMC_VIRT + 0x68) /* Clock Configuration */ +#define CSADRCFG0 (SMEMC_VIRT + 0x80) /* Address Configuration Register for CS0 */ +#define CSADRCFG1 (SMEMC_VIRT + 0x84) /* Address Configuration Register for CS1 */ +#define CSADRCFG2 (SMEMC_VIRT + 0x88) /* Address Configuration Register for CS2 */ +#define CSADRCFG3 (SMEMC_VIRT + 0x8C) /* Address Configuration Register for CS3 */ +#define CSMSADRCFG (SMEMC_VIRT + 0xA0) /* Chip Select Configuration Register */ + +/* + * More handy macros for PCMCIA + * + * Arg is socket number + */ +#define MCMEM(s) (SMEMC_VIRT + 0x28 + ((s)<<2)) /* Card interface Common Memory Space Socket s Timing */ +#define MCATT(s) (SMEMC_VIRT + 0x30 + ((s)<<2)) /* Card interface Attribute Space Socket s Timing Configuration */ +#define MCIO(s) (SMEMC_VIRT + 0x38 + ((s)<<2)) /* Card interface I/O Space Socket s Timing Configuration */ + +/* MECR register defines */ +#define MECR_NOS (1 << 0) /* Number Of Sockets: 0 -> 1 sock, 1 -> 2 sock */ +#define MECR_CIT (1 << 1) /* Card Is There: 0 -> no card, 1 -> card inserted */ + +#define MDCNFG_DE0 (1 << 0) /* SDRAM Bank 0 Enable */ +#define MDCNFG_DE1 (1 << 1) /* SDRAM Bank 1 Enable */ +#define MDCNFG_DE2 (1 << 16) /* SDRAM Bank 2 Enable */ +#define MDCNFG_DE3 (1 << 17) /* SDRAM Bank 3 Enable */ + +#define MDREFR_K0DB4 (1 << 29) /* SDCLK0 Divide by 4 Control/Status */ +#define MDREFR_K2FREE (1 << 25) /* SDRAM Free-Running Control */ +#define MDREFR_K1FREE (1 << 24) /* SDRAM Free-Running Control */ +#define MDREFR_K0FREE (1 << 23) /* SDRAM Free-Running Control */ +#define MDREFR_SLFRSH (1 << 22) /* SDRAM Self-Refresh Control/Status */ +#define MDREFR_APD (1 << 20) /* SDRAM/SSRAM Auto-Power-Down Enable */ +#define MDREFR_K2DB2 (1 << 19) /* SDCLK2 Divide by 2 Control/Status */ +#define MDREFR_K2RUN (1 << 18) /* SDCLK2 Run Control/Status */ +#define MDREFR_K1DB2 (1 << 17) /* SDCLK1 Divide by 2 Control/Status */ +#define MDREFR_K1RUN (1 << 16) /* SDCLK1 Run Control/Status */ +#define MDREFR_E1PIN (1 << 15) /* SDCKE1 Level Control/Status */ +#define MDREFR_K0DB2 (1 << 14) /* SDCLK0 Divide by 2 Control/Status */ +#define MDREFR_K0RUN (1 << 13) /* SDCLK0 Run Control/Status */ +#define MDREFR_E0PIN (1 << 12) /* SDCKE0 Level Control/Status */ + +#endif diff --git a/arch/arm/mach-pxa/include/mach/spitz.h b/arch/arm/mach-pxa/include/mach/spitz.h new file mode 100644 index 000000000..04828d891 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/spitz.h @@ -0,0 +1,185 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ +/* + * Hardware specific definitions for SL-Cx000 series of PDAs + * + * Copyright (c) 2005 Alexander Wykes + * Copyright (c) 2005 Richard Purdie + * + * Based on Sharp's 2.4 kernel patches + */ +#ifndef __ASM_ARCH_SPITZ_H +#define __ASM_ARCH_SPITZ_H 1 +#endif + +#include "irqs.h" /* PXA_NR_BUILTIN_GPIO, PXA_GPIO_TO_IRQ */ +#include <linux/fb.h> + +/* Spitz/Akita GPIOs */ + +#define SPITZ_GPIO_KEY_INT (0) /* Key Interrupt */ +#define SPITZ_GPIO_RESET (1) +#define SPITZ_GPIO_nSD_DETECT (9) +#define SPITZ_GPIO_TP_INT (11) /* Touch Panel interrupt */ +#define SPITZ_GPIO_AK_INT (13) /* Remote Control */ +#define SPITZ_GPIO_ADS7846_CS (14) +#define SPITZ_GPIO_SYNC (16) +#define SPITZ_GPIO_MAX1111_CS (20) +#define SPITZ_GPIO_FATAL_BAT (21) +#define SPITZ_GPIO_HSYNC (22) +#define SPITZ_GPIO_nSD_CLK (32) +#define SPITZ_GPIO_USB_DEVICE (35) +#define SPITZ_GPIO_USB_HOST (37) +#define SPITZ_GPIO_USB_CONNECT (41) +#define SPITZ_GPIO_LCDCON_CS (53) +#define SPITZ_GPIO_nPCE (54) +#define SPITZ_GPIO_nSD_WP (81) +#define SPITZ_GPIO_ON_RESET (89) +#define SPITZ_GPIO_BAT_COVER (90) +#define SPITZ_GPIO_CF_CD (94) +#define SPITZ_GPIO_ON_KEY (95) +#define SPITZ_GPIO_SWA (97) +#define SPITZ_GPIO_SWB (96) +#define SPITZ_GPIO_CHRG_FULL (101) +#define SPITZ_GPIO_CO (101) +#define SPITZ_GPIO_CF_IRQ (105) +#define SPITZ_GPIO_AC_IN (115) +#define SPITZ_GPIO_HP_IN (116) + +/* Spitz Only GPIOs */ + +#define SPITZ_GPIO_CF2_IRQ (106) /* CF slot1 Ready */ +#define SPITZ_GPIO_CF2_CD (93) + + +/* Spitz/Akita Keyboard Definitions */ + +#define SPITZ_KEY_STROBE_NUM (11) +#define SPITZ_KEY_SENSE_NUM (7) +#define SPITZ_GPIO_G0_STROBE_BIT 0x0f800000 +#define SPITZ_GPIO_G1_STROBE_BIT 0x00100000 +#define SPITZ_GPIO_G2_STROBE_BIT 0x01000000 +#define SPITZ_GPIO_G3_STROBE_BIT 0x00041880 +#define SPITZ_GPIO_G0_SENSE_BIT 0x00021000 +#define SPITZ_GPIO_G1_SENSE_BIT 0x000000d4 +#define SPITZ_GPIO_G2_SENSE_BIT 0x08000000 +#define SPITZ_GPIO_G3_SENSE_BIT 0x00000000 + +#define SPITZ_GPIO_KEY_STROBE0 88 +#define SPITZ_GPIO_KEY_STROBE1 23 +#define SPITZ_GPIO_KEY_STROBE2 24 +#define SPITZ_GPIO_KEY_STROBE3 25 +#define SPITZ_GPIO_KEY_STROBE4 26 +#define SPITZ_GPIO_KEY_STROBE5 27 +#define SPITZ_GPIO_KEY_STROBE6 52 +#define SPITZ_GPIO_KEY_STROBE7 103 +#define SPITZ_GPIO_KEY_STROBE8 107 +#define SPITZ_GPIO_KEY_STROBE9 108 +#define SPITZ_GPIO_KEY_STROBE10 114 + +#define SPITZ_GPIO_KEY_SENSE0 12 +#define SPITZ_GPIO_KEY_SENSE1 17 +#define SPITZ_GPIO_KEY_SENSE2 91 +#define SPITZ_GPIO_KEY_SENSE3 34 +#define SPITZ_GPIO_KEY_SENSE4 36 +#define SPITZ_GPIO_KEY_SENSE5 38 +#define SPITZ_GPIO_KEY_SENSE6 39 + + +/* Spitz Scoop Device (No. 1) GPIOs */ +/* Suspend States in comments */ +#define SPITZ_SCP_LED_GREEN SCOOP_GPCR_PA11 /* Keep */ +#define SPITZ_SCP_JK_B SCOOP_GPCR_PA12 /* Keep */ +#define SPITZ_SCP_CHRG_ON SCOOP_GPCR_PA13 /* Keep */ +#define SPITZ_SCP_MUTE_L SCOOP_GPCR_PA14 /* Low */ +#define SPITZ_SCP_MUTE_R SCOOP_GPCR_PA15 /* Low */ +#define SPITZ_SCP_CF_POWER SCOOP_GPCR_PA16 /* Keep */ +#define SPITZ_SCP_LED_ORANGE SCOOP_GPCR_PA17 /* Keep */ +#define SPITZ_SCP_JK_A SCOOP_GPCR_PA18 /* Low */ +#define SPITZ_SCP_ADC_TEMP_ON SCOOP_GPCR_PA19 /* Low */ + +#define SPITZ_SCP_IO_DIR (SPITZ_SCP_JK_B | SPITZ_SCP_CHRG_ON | \ + SPITZ_SCP_MUTE_L | SPITZ_SCP_MUTE_R | \ + SPITZ_SCP_CF_POWER | SPITZ_SCP_JK_A | SPITZ_SCP_ADC_TEMP_ON) +#define SPITZ_SCP_IO_OUT (SPITZ_SCP_CHRG_ON | SPITZ_SCP_MUTE_L | SPITZ_SCP_MUTE_R) +#define SPITZ_SCP_SUS_CLR (SPITZ_SCP_MUTE_L | SPITZ_SCP_MUTE_R | SPITZ_SCP_JK_A | SPITZ_SCP_ADC_TEMP_ON) +#define SPITZ_SCP_SUS_SET 0 + +#define SPITZ_SCP_GPIO_BASE (PXA_NR_BUILTIN_GPIO) +#define SPITZ_GPIO_LED_GREEN (SPITZ_SCP_GPIO_BASE + 0) +#define SPITZ_GPIO_JK_B (SPITZ_SCP_GPIO_BASE + 1) +#define SPITZ_GPIO_CHRG_ON (SPITZ_SCP_GPIO_BASE + 2) +#define SPITZ_GPIO_MUTE_L (SPITZ_SCP_GPIO_BASE + 3) +#define SPITZ_GPIO_MUTE_R (SPITZ_SCP_GPIO_BASE + 4) +#define SPITZ_GPIO_CF_POWER (SPITZ_SCP_GPIO_BASE + 5) +#define SPITZ_GPIO_LED_ORANGE (SPITZ_SCP_GPIO_BASE + 6) +#define SPITZ_GPIO_JK_A (SPITZ_SCP_GPIO_BASE + 7) +#define SPITZ_GPIO_ADC_TEMP_ON (SPITZ_SCP_GPIO_BASE + 8) + +/* Spitz Scoop Device (No. 2) GPIOs */ +/* Suspend States in comments */ +#define SPITZ_SCP2_IR_ON SCOOP_GPCR_PA11 /* High */ +#define SPITZ_SCP2_AKIN_PULLUP SCOOP_GPCR_PA12 /* Keep */ +#define SPITZ_SCP2_RESERVED_1 SCOOP_GPCR_PA13 /* High */ +#define SPITZ_SCP2_RESERVED_2 SCOOP_GPCR_PA14 /* Low */ +#define SPITZ_SCP2_RESERVED_3 SCOOP_GPCR_PA15 /* Low */ +#define SPITZ_SCP2_RESERVED_4 SCOOP_GPCR_PA16 /* Low */ +#define SPITZ_SCP2_BACKLIGHT_CONT SCOOP_GPCR_PA17 /* Low */ +#define SPITZ_SCP2_BACKLIGHT_ON SCOOP_GPCR_PA18 /* Low */ +#define SPITZ_SCP2_MIC_BIAS SCOOP_GPCR_PA19 /* Low */ + +#define SPITZ_SCP2_IO_DIR (SPITZ_SCP2_AKIN_PULLUP | SPITZ_SCP2_RESERVED_1 | \ + SPITZ_SCP2_RESERVED_2 | SPITZ_SCP2_RESERVED_3 | SPITZ_SCP2_RESERVED_4 | \ + SPITZ_SCP2_BACKLIGHT_CONT | SPITZ_SCP2_BACKLIGHT_ON | SPITZ_SCP2_MIC_BIAS) + +#define SPITZ_SCP2_IO_OUT (SPITZ_SCP2_AKIN_PULLUP | SPITZ_SCP2_RESERVED_1) +#define SPITZ_SCP2_SUS_CLR (SPITZ_SCP2_RESERVED_2 | SPITZ_SCP2_RESERVED_3 | SPITZ_SCP2_RESERVED_4 | \ + SPITZ_SCP2_BACKLIGHT_CONT | SPITZ_SCP2_BACKLIGHT_ON | SPITZ_SCP2_MIC_BIAS) +#define SPITZ_SCP2_SUS_SET (SPITZ_SCP2_IR_ON | SPITZ_SCP2_RESERVED_1) + +#define SPITZ_SCP2_GPIO_BASE (PXA_NR_BUILTIN_GPIO + 12) +#define SPITZ_GPIO_IR_ON (SPITZ_SCP2_GPIO_BASE + 0) +#define SPITZ_GPIO_AKIN_PULLUP (SPITZ_SCP2_GPIO_BASE + 1) +#define SPITZ_GPIO_RESERVED_1 (SPITZ_SCP2_GPIO_BASE + 2) +#define SPITZ_GPIO_RESERVED_2 (SPITZ_SCP2_GPIO_BASE + 3) +#define SPITZ_GPIO_RESERVED_3 (SPITZ_SCP2_GPIO_BASE + 4) +#define SPITZ_GPIO_RESERVED_4 (SPITZ_SCP2_GPIO_BASE + 5) +#define SPITZ_GPIO_BACKLIGHT_CONT (SPITZ_SCP2_GPIO_BASE + 6) +#define SPITZ_GPIO_BACKLIGHT_ON (SPITZ_SCP2_GPIO_BASE + 7) +#define SPITZ_GPIO_MIC_BIAS (SPITZ_SCP2_GPIO_BASE + 8) + +/* Akita IO Expander GPIOs */ +#define AKITA_IOEXP_GPIO_BASE (PXA_NR_BUILTIN_GPIO + 12) +#define AKITA_GPIO_RESERVED_0 (AKITA_IOEXP_GPIO_BASE + 0) +#define AKITA_GPIO_RESERVED_1 (AKITA_IOEXP_GPIO_BASE + 1) +#define AKITA_GPIO_MIC_BIAS (AKITA_IOEXP_GPIO_BASE + 2) +#define AKITA_GPIO_BACKLIGHT_ON (AKITA_IOEXP_GPIO_BASE + 3) +#define AKITA_GPIO_BACKLIGHT_CONT (AKITA_IOEXP_GPIO_BASE + 4) +#define AKITA_GPIO_AKIN_PULLUP (AKITA_IOEXP_GPIO_BASE + 5) +#define AKITA_GPIO_IR_ON (AKITA_IOEXP_GPIO_BASE + 6) +#define AKITA_GPIO_RESERVED_7 (AKITA_IOEXP_GPIO_BASE + 7) + +/* Spitz IRQ Definitions */ + +#define SPITZ_IRQ_GPIO_KEY_INT PXA_GPIO_TO_IRQ(SPITZ_GPIO_KEY_INT) +#define SPITZ_IRQ_GPIO_AC_IN PXA_GPIO_TO_IRQ(SPITZ_GPIO_AC_IN) +#define SPITZ_IRQ_GPIO_AK_INT PXA_GPIO_TO_IRQ(SPITZ_GPIO_AK_INT) +#define SPITZ_IRQ_GPIO_HP_IN PXA_GPIO_TO_IRQ(SPITZ_GPIO_HP_IN) +#define SPITZ_IRQ_GPIO_TP_INT PXA_GPIO_TO_IRQ(SPITZ_GPIO_TP_INT) +#define SPITZ_IRQ_GPIO_SYNC PXA_GPIO_TO_IRQ(SPITZ_GPIO_SYNC) +#define SPITZ_IRQ_GPIO_ON_KEY PXA_GPIO_TO_IRQ(SPITZ_GPIO_ON_KEY) +#define SPITZ_IRQ_GPIO_SWA PXA_GPIO_TO_IRQ(SPITZ_GPIO_SWA) +#define SPITZ_IRQ_GPIO_SWB PXA_GPIO_TO_IRQ(SPITZ_GPIO_SWB) +#define SPITZ_IRQ_GPIO_BAT_COVER PXA_GPIO_TO_IRQ(SPITZ_GPIO_BAT_COVER) +#define SPITZ_IRQ_GPIO_FATAL_BAT PXA_GPIO_TO_IRQ(SPITZ_GPIO_FATAL_BAT) +#define SPITZ_IRQ_GPIO_CO PXA_GPIO_TO_IRQ(SPITZ_GPIO_CO) +#define SPITZ_IRQ_GPIO_CF_IRQ PXA_GPIO_TO_IRQ(SPITZ_GPIO_CF_IRQ) +#define SPITZ_IRQ_GPIO_CF_CD PXA_GPIO_TO_IRQ(SPITZ_GPIO_CF_CD) +#define SPITZ_IRQ_GPIO_CF2_IRQ PXA_GPIO_TO_IRQ(SPITZ_GPIO_CF2_IRQ) +#define SPITZ_IRQ_GPIO_nSD_INT PXA_GPIO_TO_IRQ(SPITZ_GPIO_nSD_INT) +#define SPITZ_IRQ_GPIO_nSD_DETECT PXA_GPIO_TO_IRQ(SPITZ_GPIO_nSD_DETECT) + +/* + * Shared data structures + */ +extern struct platform_device spitzssp_device; +extern struct sharpsl_charger_machinfo spitz_pm_machinfo; diff --git a/arch/arm/mach-pxa/include/mach/tosa.h b/arch/arm/mach-pxa/include/mach/tosa.h new file mode 100644 index 000000000..8bfaca3a8 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/tosa.h @@ -0,0 +1,183 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ +/* + * Hardware specific definitions for Sharp SL-C6000x series of PDAs + * + * Copyright (c) 2005 Dirk Opfer + * + * Based on Sharp's 2.4 kernel patches + */ +#ifndef _ASM_ARCH_TOSA_H_ +#define _ASM_ARCH_TOSA_H_ 1 + +#include "irqs.h" /* PXA_NR_BUILTIN_GPIO */ + +/* TOSA Chip selects */ +#define TOSA_LCDC_PHYS PXA_CS4_PHYS +/* Internel Scoop */ +#define TOSA_CF_PHYS (PXA_CS2_PHYS + 0x00800000) +/* Jacket Scoop */ +#define TOSA_SCOOP_PHYS (PXA_CS5_PHYS + 0x00800000) + +#define TOSA_NR_IRQS (IRQ_BOARD_START + TC6393XB_NR_IRQS) +/* + * SCOOP2 internal GPIOs + */ +#define TOSA_SCOOP_GPIO_BASE PXA_NR_BUILTIN_GPIO +#define TOSA_SCOOP_PXA_VCORE1 SCOOP_GPCR_PA11 +#define TOSA_GPIO_TC6393XB_REST_IN (TOSA_SCOOP_GPIO_BASE + 1) +#define TOSA_GPIO_IR_POWERDWN (TOSA_SCOOP_GPIO_BASE + 2) +#define TOSA_GPIO_SD_WP (TOSA_SCOOP_GPIO_BASE + 3) +#define TOSA_GPIO_PWR_ON (TOSA_SCOOP_GPIO_BASE + 4) +#define TOSA_SCOOP_AUD_PWR_ON SCOOP_GPCR_PA16 +#define TOSA_GPIO_BT_RESET (TOSA_SCOOP_GPIO_BASE + 6) +#define TOSA_GPIO_BT_PWR_EN (TOSA_SCOOP_GPIO_BASE + 7) +#define TOSA_SCOOP_AC_IN_OL SCOOP_GPCR_PA19 + +/* GPIO Direction 1 : output mode / 0:input mode */ +#define TOSA_SCOOP_IO_DIR (TOSA_SCOOP_PXA_VCORE1 | \ + TOSA_SCOOP_AUD_PWR_ON) + +/* + * SCOOP2 jacket GPIOs + */ +#define TOSA_SCOOP_JC_GPIO_BASE (PXA_NR_BUILTIN_GPIO + 12) +#define TOSA_GPIO_BT_LED (TOSA_SCOOP_JC_GPIO_BASE + 0) +#define TOSA_GPIO_NOTE_LED (TOSA_SCOOP_JC_GPIO_BASE + 1) +#define TOSA_GPIO_CHRG_ERR_LED (TOSA_SCOOP_JC_GPIO_BASE + 2) +#define TOSA_GPIO_USB_PULLUP (TOSA_SCOOP_JC_GPIO_BASE + 3) +#define TOSA_GPIO_TC6393XB_SUSPEND (TOSA_SCOOP_JC_GPIO_BASE + 4) +#define TOSA_GPIO_TC6393XB_L3V_ON (TOSA_SCOOP_JC_GPIO_BASE + 5) +#define TOSA_SCOOP_JC_WLAN_DETECT SCOOP_GPCR_PA17 +#define TOSA_GPIO_WLAN_LED (TOSA_SCOOP_JC_GPIO_BASE + 7) +#define TOSA_SCOOP_JC_CARD_LIMIT_SEL SCOOP_GPCR_PA19 + +/* GPIO Direction 1 : output mode / 0:input mode */ +#define TOSA_SCOOP_JC_IO_DIR (TOSA_SCOOP_JC_CARD_LIMIT_SEL) + +/* + * TC6393XB GPIOs + */ +#define TOSA_TC6393XB_GPIO_BASE (PXA_NR_BUILTIN_GPIO + 2 * 12) + +#define TOSA_GPIO_TG_ON (TOSA_TC6393XB_GPIO_BASE + 0) +#define TOSA_GPIO_L_MUTE (TOSA_TC6393XB_GPIO_BASE + 1) +#define TOSA_GPIO_BL_C20MA (TOSA_TC6393XB_GPIO_BASE + 3) +#define TOSA_GPIO_CARD_VCC_ON (TOSA_TC6393XB_GPIO_BASE + 4) +#define TOSA_GPIO_CHARGE_OFF (TOSA_TC6393XB_GPIO_BASE + 6) +#define TOSA_GPIO_CHARGE_OFF_JC (TOSA_TC6393XB_GPIO_BASE + 7) +#define TOSA_GPIO_BAT0_V_ON (TOSA_TC6393XB_GPIO_BASE + 9) +#define TOSA_GPIO_BAT1_V_ON (TOSA_TC6393XB_GPIO_BASE + 10) +#define TOSA_GPIO_BU_CHRG_ON (TOSA_TC6393XB_GPIO_BASE + 11) +#define TOSA_GPIO_BAT_SW_ON (TOSA_TC6393XB_GPIO_BASE + 12) +#define TOSA_GPIO_BAT0_TH_ON (TOSA_TC6393XB_GPIO_BASE + 14) +#define TOSA_GPIO_BAT1_TH_ON (TOSA_TC6393XB_GPIO_BASE + 15) + +/* + * PXA GPIOs + */ +#define TOSA_GPIO_POWERON (0) +#define TOSA_GPIO_RESET (1) +#define TOSA_GPIO_AC_IN (2) +#define TOSA_GPIO_RECORD_BTN (3) +#define TOSA_GPIO_SYNC (4) /* Cradle SYNC Button */ +#define TOSA_GPIO_USB_IN (5) +#define TOSA_GPIO_JACKET_DETECT (7) +#define TOSA_GPIO_nSD_DETECT (9) +#define TOSA_GPIO_nSD_INT (10) +#define TOSA_GPIO_TC6393XB_CLK (11) +#define TOSA_GPIO_BAT1_CRG (12) +#define TOSA_GPIO_CF_CD (13) +#define TOSA_GPIO_BAT0_CRG (14) +#define TOSA_GPIO_TC6393XB_INT (15) +#define TOSA_GPIO_BAT0_LOW (17) +#define TOSA_GPIO_TC6393XB_RDY (18) +#define TOSA_GPIO_ON_RESET (19) +#define TOSA_GPIO_EAR_IN (20) +#define TOSA_GPIO_CF_IRQ (21) /* CF slot0 Ready */ +#define TOSA_GPIO_ON_KEY (22) +#define TOSA_GPIO_VGA_LINE (27) +#define TOSA_GPIO_TP_INT (32) /* Touch Panel pen down interrupt */ +#define TOSA_GPIO_JC_CF_IRQ (36) /* CF slot1 Ready */ +#define TOSA_GPIO_BAT_LOCKED (38) /* Battery locked */ +#define TOSA_GPIO_IRDA_TX (47) +#define TOSA_GPIO_TG_SPI_SCLK (81) +#define TOSA_GPIO_TG_SPI_CS (82) +#define TOSA_GPIO_TG_SPI_MOSI (83) +#define TOSA_GPIO_BAT1_LOW (84) + +#define TOSA_GPIO_HP_IN GPIO_EAR_IN + +#define TOSA_GPIO_MAIN_BAT_LOW GPIO_BAT0_LOW + +#define TOSA_KEY_STROBE_NUM (11) +#define TOSA_KEY_SENSE_NUM (7) + +#define TOSA_GPIO_HIGH_STROBE_BIT (0xfc000000) +#define TOSA_GPIO_LOW_STROBE_BIT (0x0000001f) +#define TOSA_GPIO_ALL_SENSE_BIT (0x00000fe0) +#define TOSA_GPIO_ALL_SENSE_RSHIFT (5) +#define TOSA_GPIO_STROBE_BIT(a) GPIO_bit(58+(a)) +#define TOSA_GPIO_SENSE_BIT(a) GPIO_bit(69+(a)) +#define TOSA_GAFR_HIGH_STROBE_BIT (0xfff00000) +#define TOSA_GAFR_LOW_STROBE_BIT (0x000003ff) +#define TOSA_GAFR_ALL_SENSE_BIT (0x00fffc00) +#define TOSA_GPIO_KEY_SENSE(a) (69+(a)) +#define TOSA_GPIO_KEY_STROBE(a) (58+(a)) + +/* + * Interrupts + */ +#define TOSA_IRQ_GPIO_WAKEUP PXA_GPIO_TO_IRQ(TOSA_GPIO_WAKEUP) +#define TOSA_IRQ_GPIO_AC_IN PXA_GPIO_TO_IRQ(TOSA_GPIO_AC_IN) +#define TOSA_IRQ_GPIO_RECORD_BTN PXA_GPIO_TO_IRQ(TOSA_GPIO_RECORD_BTN) +#define TOSA_IRQ_GPIO_SYNC PXA_GPIO_TO_IRQ(TOSA_GPIO_SYNC) +#define TOSA_IRQ_GPIO_USB_IN PXA_GPIO_TO_IRQ(TOSA_GPIO_USB_IN) +#define TOSA_IRQ_GPIO_JACKET_DETECT PXA_GPIO_TO_IRQ(TOSA_GPIO_JACKET_DETECT) +#define TOSA_IRQ_GPIO_nSD_INT PXA_GPIO_TO_IRQ(TOSA_GPIO_nSD_INT) +#define TOSA_IRQ_GPIO_nSD_DETECT PXA_GPIO_TO_IRQ(TOSA_GPIO_nSD_DETECT) +#define TOSA_IRQ_GPIO_BAT1_CRG PXA_GPIO_TO_IRQ(TOSA_GPIO_BAT1_CRG) +#define TOSA_IRQ_GPIO_CF_CD PXA_GPIO_TO_IRQ(TOSA_GPIO_CF_CD) +#define TOSA_IRQ_GPIO_BAT0_CRG PXA_GPIO_TO_IRQ(TOSA_GPIO_BAT0_CRG) +#define TOSA_IRQ_GPIO_TC6393XB_INT PXA_GPIO_TO_IRQ(TOSA_GPIO_TC6393XB_INT) +#define TOSA_IRQ_GPIO_BAT0_LOW PXA_GPIO_TO_IRQ(TOSA_GPIO_BAT0_LOW) +#define TOSA_IRQ_GPIO_EAR_IN PXA_GPIO_TO_IRQ(TOSA_GPIO_EAR_IN) +#define TOSA_IRQ_GPIO_CF_IRQ PXA_GPIO_TO_IRQ(TOSA_GPIO_CF_IRQ) +#define TOSA_IRQ_GPIO_ON_KEY PXA_GPIO_TO_IRQ(TOSA_GPIO_ON_KEY) +#define TOSA_IRQ_GPIO_VGA_LINE PXA_GPIO_TO_IRQ(TOSA_GPIO_VGA_LINE) +#define TOSA_IRQ_GPIO_TP_INT PXA_GPIO_TO_IRQ(TOSA_GPIO_TP_INT) +#define TOSA_IRQ_GPIO_JC_CF_IRQ PXA_GPIO_TO_IRQ(TOSA_GPIO_JC_CF_IRQ) +#define TOSA_IRQ_GPIO_BAT_LOCKED PXA_GPIO_TO_IRQ(TOSA_GPIO_BAT_LOCKED) +#define TOSA_IRQ_GPIO_BAT1_LOW PXA_GPIO_TO_IRQ(TOSA_GPIO_BAT1_LOW) +#define TOSA_IRQ_GPIO_KEY_SENSE(a) PXA_GPIO_TO_IRQ(69+(a)) + +#define TOSA_IRQ_GPIO_MAIN_BAT_LOW PXA_GPIO_TO_IRQ(TOSA_GPIO_MAIN_BAT_LOW) + +#define TOSA_KEY_SYNC KEY_102ND /* ??? */ + +#ifndef CONFIG_TOSA_USE_EXT_KEYCODES +#define TOSA_KEY_RECORD KEY_YEN +#define TOSA_KEY_ADDRESSBOOK KEY_KATAKANA +#define TOSA_KEY_CANCEL KEY_ESC +#define TOSA_KEY_CENTER KEY_HIRAGANA +#define TOSA_KEY_OK KEY_HENKAN +#define TOSA_KEY_CALENDAR KEY_KATAKANAHIRAGANA +#define TOSA_KEY_HOMEPAGE KEY_HANGEUL +#define TOSA_KEY_LIGHT KEY_MUHENKAN +#define TOSA_KEY_MENU KEY_HANJA +#define TOSA_KEY_FN KEY_RIGHTALT +#define TOSA_KEY_MAIL KEY_ZENKAKUHANKAKU +#else +#define TOSA_KEY_RECORD KEY_RECORD +#define TOSA_KEY_ADDRESSBOOK KEY_ADDRESSBOOK +#define TOSA_KEY_CANCEL KEY_CANCEL +#define TOSA_KEY_CENTER KEY_SELECT /* ??? */ +#define TOSA_KEY_OK KEY_OK +#define TOSA_KEY_CALENDAR KEY_CALENDAR +#define TOSA_KEY_HOMEPAGE KEY_HOMEPAGE +#define TOSA_KEY_LIGHT KEY_KBDILLUMTOGGLE +#define TOSA_KEY_MENU KEY_MENU +#define TOSA_KEY_FN KEY_FN +#define TOSA_KEY_MAIL KEY_MAIL +#endif + +#endif /* _ASM_ARCH_TOSA_H_ */ diff --git a/arch/arm/mach-pxa/include/mach/trizeps4.h b/arch/arm/mach-pxa/include/mach/trizeps4.h new file mode 100644 index 000000000..3cddb1428 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/trizeps4.h @@ -0,0 +1,165 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/************************************************************************ + * Include file for TRIZEPS4 SoM and ConXS eval-board + * Copyright (c) Jürgen Schindele + * 2006 + ************************************************************************/ + +/* + * Includes/Defines + */ +#ifndef _TRIPEPS4_H_ +#define _TRIPEPS4_H_ + +#include "irqs.h" /* PXA_GPIO_TO_IRQ */ + +/* physical memory regions */ +#define TRIZEPS4_FLASH_PHYS (PXA_CS0_PHYS) /* Flash region */ +#define TRIZEPS4_DISK_PHYS (PXA_CS1_PHYS) /* Disk On Chip region */ +#define TRIZEPS4_ETH_PHYS (PXA_CS2_PHYS) /* Ethernet DM9000 region */ +#define TRIZEPS4_PIC_PHYS (PXA_CS3_PHYS) /* Logic chip on ConXS-Board */ +#define TRIZEPS4_SDRAM_BASE 0xa0000000 /* SDRAM region */ + + /* Logic on ConXS-board CSFR register*/ +#define TRIZEPS4_CFSR_PHYS (PXA_CS3_PHYS) + /* Logic on ConXS-board BOCR register*/ +#define TRIZEPS4_BOCR_PHYS (PXA_CS3_PHYS+0x02000000) + /* Logic on ConXS-board IRCR register*/ +#define TRIZEPS4_IRCR_PHYS (PXA_CS3_PHYS+0x02400000) + /* Logic on ConXS-board UPSR register*/ +#define TRIZEPS4_UPSR_PHYS (PXA_CS3_PHYS+0x02800000) + /* Logic on ConXS-board DICR register*/ +#define TRIZEPS4_DICR_PHYS (PXA_CS3_PHYS+0x03800000) + +/* virtual memory regions */ +#define TRIZEPS4_DISK_VIRT 0xF0000000 /* Disk On Chip region */ + +#define TRIZEPS4_PIC_VIRT 0xF0100000 /* not used */ +#define TRIZEPS4_CFSR_VIRT 0xF0100000 +#define TRIZEPS4_BOCR_VIRT 0xF0200000 +#define TRIZEPS4_DICR_VIRT 0xF0300000 +#define TRIZEPS4_IRCR_VIRT 0xF0400000 +#define TRIZEPS4_UPSR_VIRT 0xF0500000 + +/* size of flash */ +#define TRIZEPS4_FLASH_SIZE 0x02000000 /* Flash size 32 MB */ + +/* Ethernet Controller Davicom DM9000 */ +#define GPIO_DM9000 101 +#define TRIZEPS4_ETH_IRQ PXA_GPIO_TO_IRQ(GPIO_DM9000) + +/* UCB1400 audio / TS-controller */ +#define GPIO_UCB1400 1 +#define TRIZEPS4_UCB1400_IRQ PXA_GPIO_TO_IRQ(GPIO_UCB1400) + +/* PCMCIA socket Compact Flash */ +#define GPIO_PCD 11 /* PCMCIA Card Detect */ +#define TRIZEPS4_CD_IRQ PXA_GPIO_TO_IRQ(GPIO_PCD) +#define GPIO_PRDY 13 /* READY / nINT */ +#define TRIZEPS4_READY_NINT PXA_GPIO_TO_IRQ(GPIO_PRDY) + +/* MMC socket */ +#define GPIO_MMC_DET 12 +#define TRIZEPS4_MMC_IRQ PXA_GPIO_TO_IRQ(GPIO_MMC_DET) + +/* DOC NAND chip */ +#define GPIO_DOC_LOCK 94 +#define GPIO_DOC_IRQ 93 +#define TRIZEPS4_DOC_IRQ PXA_GPIO_TO_IRQ(GPIO_DOC_IRQ) + +/* SPI interface */ +#define GPIO_SPI 53 +#define TRIZEPS4_SPI_IRQ PXA_GPIO_TO_IRQ(GPIO_SPI) + +/* LEDS using tx2 / rx2 */ +#define GPIO_SYS_BUSY_LED 46 +#define GPIO_HEARTBEAT_LED 47 + +/* Off-module PIC on ConXS board */ +#define GPIO_PIC 0 +#define TRIZEPS4_PIC_IRQ PXA_GPIO_TO_IRQ(GPIO_PIC) + +#ifdef CONFIG_MACH_TRIZEPS_CONXS +/* for CONXS base board define these registers */ +#define CFSR_P2V(x) ((x) - TRIZEPS4_CFSR_PHYS + TRIZEPS4_CFSR_VIRT) +#define CFSR_V2P(x) ((x) - TRIZEPS4_CFSR_VIRT + TRIZEPS4_CFSR_PHYS) + +#define BCR_P2V(x) ((x) - TRIZEPS4_BOCR_PHYS + TRIZEPS4_BOCR_VIRT) +#define BCR_V2P(x) ((x) - TRIZEPS4_BOCR_VIRT + TRIZEPS4_BOCR_PHYS) + +#define DCR_P2V(x) ((x) - TRIZEPS4_DICR_PHYS + TRIZEPS4_DICR_VIRT) +#define DCR_V2P(x) ((x) - TRIZEPS4_DICR_VIRT + TRIZEPS4_DICR_PHYS) + +#define IRCR_P2V(x) ((x) - TRIZEPS4_IRCR_PHYS + TRIZEPS4_IRCR_VIRT) +#define IRCR_V2P(x) ((x) - TRIZEPS4_IRCR_VIRT + TRIZEPS4_IRCR_PHYS) + +#ifndef __ASSEMBLY__ +static inline unsigned short CFSR_readw(void) +{ + /* [Compact Flash Status Register] is read only */ + return *((unsigned short *)CFSR_P2V(0x0C000000)); +} +static inline void BCR_writew(unsigned short value) +{ + /* [Board Control Regsiter] is write only */ + *((unsigned short *)BCR_P2V(0x0E000000)) = value; +} +static inline void DCR_writew(unsigned short value) +{ + /* [Display Control Register] is write only */ + *((unsigned short *)DCR_P2V(0x0E000000)) = value; +} +static inline void IRCR_writew(unsigned short value) +{ + /* [InfraRed data Control Register] is write only */ + *((unsigned short *)IRCR_P2V(0x0E000000)) = value; +} +#else +#define ConXS_CFSR CFSR_P2V(0x0C000000) +#define ConXS_BCR BCR_P2V(0x0E000000) +#define ConXS_DCR DCR_P2V(0x0F800000) +#define ConXS_IRCR IRCR_P2V(0x0F800000) +#endif +#else +/* for whatever baseboard define function registers */ +static inline unsigned short CFSR_readw(void) +{ + return 0; +} +static inline void BCR_writew(unsigned short value) +{ + ; +} +static inline void DCR_writew(unsigned short value) +{ + ; +} +static inline void IRCR_writew(unsigned short value) +{ + ; +} +#endif /* CONFIG_MACH_TRIZEPS_CONXS */ + +#define ConXS_CFSR_BVD_MASK 0x0003 +#define ConXS_CFSR_BVD1 (1 << 0) +#define ConXS_CFSR_BVD2 (1 << 1) +#define ConXS_CFSR_VS_MASK 0x000C +#define ConXS_CFSR_VS1 (1 << 2) +#define ConXS_CFSR_VS2 (1 << 3) +#define ConXS_CFSR_VS_5V (0x3 << 2) +#define ConXS_CFSR_VS_3V3 0x0 + +#define ConXS_BCR_S0_POW_EN0 (1 << 0) +#define ConXS_BCR_S0_POW_EN1 (1 << 1) +#define ConXS_BCR_L_DISP (1 << 4) +#define ConXS_BCR_CF_BUF_EN (1 << 5) +#define ConXS_BCR_CF_RESET (1 << 7) +#define ConXS_BCR_S0_VCC_3V3 0x1 +#define ConXS_BCR_S0_VCC_5V0 0x2 +#define ConXS_BCR_S0_VPP_12V 0x4 +#define ConXS_BCR_S0_VPP_3V3 0x8 + +#define ConXS_IRCR_MODE (1 << 0) +#define ConXS_IRCR_SD (1 << 1) + +#endif /* _TRIPEPS4_H_ */ diff --git a/arch/arm/mach-pxa/include/mach/uncompress.h b/arch/arm/mach-pxa/include/mach/uncompress.h new file mode 100644 index 000000000..c36306064 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/uncompress.h @@ -0,0 +1,71 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ +/* + * arch/arm/mach-pxa/include/mach/uncompress.h + * + * Author: Nicolas Pitre + * Copyright: (C) 2001 MontaVista Software Inc. + */ + +#include <linux/serial_reg.h> +#include <asm/mach-types.h> + +#define FFUART_BASE (0x40100000) +#define BTUART_BASE (0x40200000) +#define STUART_BASE (0x40700000) + +unsigned long uart_base; +unsigned int uart_shift; +unsigned int uart_is_pxa; + +static inline unsigned char uart_read(int offset) +{ + return *(volatile unsigned char *)(uart_base + (offset << uart_shift)); +} + +static inline void uart_write(unsigned char val, int offset) +{ + *(volatile unsigned char *)(uart_base + (offset << uart_shift)) = val; +} + +static inline int uart_is_enabled(void) +{ + /* assume enabled by default for non-PXA uarts */ + return uart_is_pxa ? uart_read(UART_IER) & UART_IER_UUE : 1; +} + +static inline void putc(char c) +{ + if (!uart_is_enabled()) + return; + + while (!(uart_read(UART_LSR) & UART_LSR_THRE)) + barrier(); + + uart_write(c, UART_TX); +} + +/* + * This does not append a newline + */ +static inline void flush(void) +{ +} + +static inline void arch_decomp_setup(void) +{ + /* initialize to default */ + uart_base = FFUART_BASE; + uart_shift = 2; + uart_is_pxa = 1; + + if (machine_is_littleton() || machine_is_intelmote2() + || machine_is_csb726() || machine_is_stargate2() + || machine_is_cm_x300() || machine_is_balloon3()) + uart_base = STUART_BASE; + + if (machine_is_arcom_zeus()) { + uart_base = 0x10000000; /* nCS4 */ + uart_shift = 1; + uart_is_pxa = 0; + } +} diff --git a/arch/arm/mach-pxa/include/mach/vpac270.h b/arch/arm/mach-pxa/include/mach/vpac270.h new file mode 100644 index 000000000..0cd094d8c --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/vpac270.h @@ -0,0 +1,38 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ +/* + * GPIOs and interrupts for Voipac PXA270 + * + * Copyright (C) 2010 + * Marek Vasut <marek.vasut@gmail.com> + */ + +#ifndef _INCLUDE_VPAC270_H_ +#define _INCLUDE_VPAC270_H_ + +#define GPIO1_VPAC270_USER_BTN 1 + +#define GPIO15_VPAC270_LED_ORANGE 15 + +#define GPIO81_VPAC270_BKL_ON 81 +#define GPIO83_VPAC270_NL_ON 83 + +#define GPIO52_VPAC270_SD_READONLY 52 +#define GPIO53_VPAC270_SD_DETECT_N 53 + +#define GPIO84_VPAC270_PCMCIA_CD 84 +#define GPIO35_VPAC270_PCMCIA_RDY 35 +#define GPIO107_VPAC270_PCMCIA_PPEN 107 +#define GPIO11_VPAC270_PCMCIA_RESET 11 +#define GPIO17_VPAC270_CF_CD 17 +#define GPIO12_VPAC270_CF_RDY 12 +#define GPIO16_VPAC270_CF_RESET 16 + +#define GPIO41_VPAC270_UDC_DETECT 41 + +#define GPIO114_VPAC270_ETH_IRQ 114 + +#define GPIO36_VPAC270_IDE_IRQ 36 + +#define GPIO113_VPAC270_TS_IRQ 113 + +#endif diff --git a/arch/arm/mach-pxa/include/mach/z2.h b/arch/arm/mach-pxa/include/mach/z2.h new file mode 100644 index 000000000..a78b2e28b --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/z2.h @@ -0,0 +1,37 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ +/* + * arch/arm/mach-pxa/include/mach/z2.h + * + * Author: Ken McGuire + * Created: Feb 6, 2009 + */ + +#ifndef ASM_ARCH_ZIPIT2_H +#define ASM_ARCH_ZIPIT2_H + +/* LEDs */ +#define GPIO10_ZIPITZ2_LED_WIFI 10 +#define GPIO85_ZIPITZ2_LED_CHARGED 85 +#define GPIO83_ZIPITZ2_LED_CHARGING 83 + +/* SD/MMC */ +#define GPIO96_ZIPITZ2_SD_DETECT 96 + +/* GPIO Buttons */ +#define GPIO1_ZIPITZ2_POWER_BUTTON 1 +#define GPIO98_ZIPITZ2_LID_BUTTON 98 + +/* Libertas GSPI8686 WiFi */ +#define GPIO14_ZIPITZ2_WIFI_POWER 14 +#define GPIO24_ZIPITZ2_WIFI_CS 24 +#define GPIO36_ZIPITZ2_WIFI_IRQ 36 + +/* LCD */ +#define GPIO19_ZIPITZ2_LCD_RESET 19 +#define GPIO88_ZIPITZ2_LCD_CS 88 + +/* MISC GPIOs */ +#define GPIO0_ZIPITZ2_AC_DETECT 0 +#define GPIO37_ZIPITZ2_HEADSET_DETECT 37 + +#endif |