diff options
Diffstat (limited to '')
| -rw-r--r-- | drivers/i2c/busses/i2c-mxs.c | 914 |
1 files changed, 914 insertions, 0 deletions
diff --git a/drivers/i2c/busses/i2c-mxs.c b/drivers/i2c/busses/i2c-mxs.c new file mode 100644 index 000000000..abad24808 --- /dev/null +++ b/drivers/i2c/busses/i2c-mxs.c @@ -0,0 +1,914 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Freescale MXS I2C bus driver + * + * Copyright (C) 2012-2013 Marek Vasut <marex@denx.de> + * Copyright (C) 2011-2012 Wolfram Sang, Pengutronix e.K. + * + * based on a (non-working) driver which was: + * + * Copyright (C) 2009-2010 Freescale Semiconductor, Inc. All Rights Reserved. + */ + +#include <linux/slab.h> +#include <linux/device.h> +#include <linux/module.h> +#include <linux/i2c.h> +#include <linux/err.h> +#include <linux/interrupt.h> +#include <linux/completion.h> +#include <linux/platform_device.h> +#include <linux/jiffies.h> +#include <linux/io.h> +#include <linux/stmp_device.h> +#include <linux/of.h> +#include <linux/of_device.h> +#include <linux/dma-mapping.h> +#include <linux/dmaengine.h> +#include <linux/dma/mxs-dma.h> + +#define DRIVER_NAME "mxs-i2c" + +#define MXS_I2C_CTRL0 (0x00) +#define MXS_I2C_CTRL0_SET (0x04) +#define MXS_I2C_CTRL0_CLR (0x08) + +#define MXS_I2C_CTRL0_SFTRST 0x80000000 +#define MXS_I2C_CTRL0_RUN 0x20000000 +#define MXS_I2C_CTRL0_SEND_NAK_ON_LAST 0x02000000 +#define MXS_I2C_CTRL0_PIO_MODE 0x01000000 +#define MXS_I2C_CTRL0_RETAIN_CLOCK 0x00200000 +#define MXS_I2C_CTRL0_POST_SEND_STOP 0x00100000 +#define MXS_I2C_CTRL0_PRE_SEND_START 0x00080000 +#define MXS_I2C_CTRL0_MASTER_MODE 0x00020000 +#define MXS_I2C_CTRL0_DIRECTION 0x00010000 +#define MXS_I2C_CTRL0_XFER_COUNT(v) ((v) & 0x0000FFFF) + +#define MXS_I2C_TIMING0 (0x10) +#define MXS_I2C_TIMING1 (0x20) +#define MXS_I2C_TIMING2 (0x30) + +#define MXS_I2C_CTRL1 (0x40) +#define MXS_I2C_CTRL1_SET (0x44) +#define MXS_I2C_CTRL1_CLR (0x48) + +#define MXS_I2C_CTRL1_CLR_GOT_A_NAK 0x10000000 +#define MXS_I2C_CTRL1_BUS_FREE_IRQ 0x80 +#define MXS_I2C_CTRL1_DATA_ENGINE_CMPLT_IRQ 0x40 +#define MXS_I2C_CTRL1_NO_SLAVE_ACK_IRQ 0x20 +#define MXS_I2C_CTRL1_OVERSIZE_XFER_TERM_IRQ 0x10 +#define MXS_I2C_CTRL1_EARLY_TERM_IRQ 0x08 +#define MXS_I2C_CTRL1_MASTER_LOSS_IRQ 0x04 +#define MXS_I2C_CTRL1_SLAVE_STOP_IRQ 0x02 +#define MXS_I2C_CTRL1_SLAVE_IRQ 0x01 + +#define MXS_I2C_STAT (0x50) +#define MXS_I2C_STAT_GOT_A_NAK 0x10000000 +#define MXS_I2C_STAT_BUS_BUSY 0x00000800 +#define MXS_I2C_STAT_CLK_GEN_BUSY 0x00000400 + +#define MXS_I2C_DATA(i2c) ((i2c->dev_type == MXS_I2C_V1) ? 0x60 : 0xa0) + +#define MXS_I2C_DEBUG0_CLR(i2c) ((i2c->dev_type == MXS_I2C_V1) ? 0x78 : 0xb8) + +#define MXS_I2C_DEBUG0_DMAREQ 0x80000000 + +#define MXS_I2C_IRQ_MASK (MXS_I2C_CTRL1_DATA_ENGINE_CMPLT_IRQ | \ + MXS_I2C_CTRL1_NO_SLAVE_ACK_IRQ | \ + MXS_I2C_CTRL1_EARLY_TERM_IRQ | \ + MXS_I2C_CTRL1_MASTER_LOSS_IRQ | \ + MXS_I2C_CTRL1_SLAVE_STOP_IRQ | \ + MXS_I2C_CTRL1_SLAVE_IRQ) + + +#define MXS_CMD_I2C_SELECT (MXS_I2C_CTRL0_RETAIN_CLOCK | \ + MXS_I2C_CTRL0_PRE_SEND_START | \ + MXS_I2C_CTRL0_MASTER_MODE | \ + MXS_I2C_CTRL0_DIRECTION | \ + MXS_I2C_CTRL0_XFER_COUNT(1)) + +#define MXS_CMD_I2C_WRITE (MXS_I2C_CTRL0_PRE_SEND_START | \ + MXS_I2C_CTRL0_MASTER_MODE | \ + MXS_I2C_CTRL0_DIRECTION) + +#define MXS_CMD_I2C_READ (MXS_I2C_CTRL0_SEND_NAK_ON_LAST | \ + MXS_I2C_CTRL0_MASTER_MODE) + +enum mxs_i2c_devtype { + MXS_I2C_UNKNOWN = 0, + MXS_I2C_V1, + MXS_I2C_V2, +}; + +/** + * struct mxs_i2c_dev - per device, private MXS-I2C data + * + * @dev: driver model device node + * @dev_type: distinguish i.MX23/i.MX28 features + * @regs: IO registers pointer + * @cmd_complete: completion object for transaction wait + * @cmd_err: error code for last transaction + * @adapter: i2c subsystem adapter node + */ +struct mxs_i2c_dev { + struct device *dev; + enum mxs_i2c_devtype dev_type; + void __iomem *regs; + struct completion cmd_complete; + int cmd_err; + struct i2c_adapter adapter; + + uint32_t timing0; + uint32_t timing1; + uint32_t timing2; + + /* DMA support components */ + struct dma_chan *dmach; + uint32_t pio_data[2]; + uint32_t addr_data; + struct scatterlist sg_io[2]; + bool dma_read; +}; + +static int mxs_i2c_reset(struct mxs_i2c_dev *i2c) +{ + int ret = stmp_reset_block(i2c->regs); + if (ret) + return ret; + + /* + * Configure timing for the I2C block. The I2C TIMING2 register has to + * be programmed with this particular magic number. The rest is derived + * from the XTAL speed and requested I2C speed. + * + * For details, see i.MX233 [25.4.2 - 25.4.4] and i.MX28 [27.5.2 - 27.5.4]. + */ + writel(i2c->timing0, i2c->regs + MXS_I2C_TIMING0); + writel(i2c->timing1, i2c->regs + MXS_I2C_TIMING1); + writel(i2c->timing2, i2c->regs + MXS_I2C_TIMING2); + + writel(MXS_I2C_IRQ_MASK << 8, i2c->regs + MXS_I2C_CTRL1_SET); + + return 0; +} + +static void mxs_i2c_dma_finish(struct mxs_i2c_dev *i2c) +{ + if (i2c->dma_read) { + dma_unmap_sg(i2c->dev, &i2c->sg_io[0], 1, DMA_TO_DEVICE); + dma_unmap_sg(i2c->dev, &i2c->sg_io[1], 1, DMA_FROM_DEVICE); + } else { + dma_unmap_sg(i2c->dev, i2c->sg_io, 2, DMA_TO_DEVICE); + } +} + +static void mxs_i2c_dma_irq_callback(void *param) +{ + struct mxs_i2c_dev *i2c = param; + + complete(&i2c->cmd_complete); + mxs_i2c_dma_finish(i2c); +} + +static int mxs_i2c_dma_setup_xfer(struct i2c_adapter *adap, + struct i2c_msg *msg, uint32_t flags) +{ + struct dma_async_tx_descriptor *desc; + struct mxs_i2c_dev *i2c = i2c_get_adapdata(adap); + + i2c->addr_data = i2c_8bit_addr_from_msg(msg); + + if (msg->flags & I2C_M_RD) { + i2c->dma_read = true; + + /* + * SELECT command. + */ + + /* Queue the PIO register write transfer. */ + i2c->pio_data[0] = MXS_CMD_I2C_SELECT; + desc = dmaengine_prep_slave_sg(i2c->dmach, + (struct scatterlist *)&i2c->pio_data[0], + 1, DMA_TRANS_NONE, 0); + if (!desc) { + dev_err(i2c->dev, + "Failed to get PIO reg. write descriptor.\n"); + goto select_init_pio_fail; + } + + /* Queue the DMA data transfer. */ + sg_init_one(&i2c->sg_io[0], &i2c->addr_data, 1); + dma_map_sg(i2c->dev, &i2c->sg_io[0], 1, DMA_TO_DEVICE); + desc = dmaengine_prep_slave_sg(i2c->dmach, &i2c->sg_io[0], 1, + DMA_MEM_TO_DEV, + DMA_PREP_INTERRUPT | + MXS_DMA_CTRL_WAIT4END); + if (!desc) { + dev_err(i2c->dev, + "Failed to get DMA data write descriptor.\n"); + goto select_init_dma_fail; + } + + /* + * READ command. + */ + + /* Queue the PIO register write transfer. */ + i2c->pio_data[1] = flags | MXS_CMD_I2C_READ | + MXS_I2C_CTRL0_XFER_COUNT(msg->len); + desc = dmaengine_prep_slave_sg(i2c->dmach, + (struct scatterlist *)&i2c->pio_data[1], + 1, DMA_TRANS_NONE, DMA_PREP_INTERRUPT); + if (!desc) { + dev_err(i2c->dev, + "Failed to get PIO reg. write descriptor.\n"); + goto select_init_dma_fail; + } + + /* Queue the DMA data transfer. */ + sg_init_one(&i2c->sg_io[1], msg->buf, msg->len); + dma_map_sg(i2c->dev, &i2c->sg_io[1], 1, DMA_FROM_DEVICE); + desc = dmaengine_prep_slave_sg(i2c->dmach, &i2c->sg_io[1], 1, + DMA_DEV_TO_MEM, + DMA_PREP_INTERRUPT | + MXS_DMA_CTRL_WAIT4END); + if (!desc) { + dev_err(i2c->dev, + "Failed to get DMA data write descriptor.\n"); + goto read_init_dma_fail; + } + } else { + i2c->dma_read = false; + + /* + * WRITE command. + */ + + /* Queue the PIO register write transfer. */ + i2c->pio_data[0] = flags | MXS_CMD_I2C_WRITE | + MXS_I2C_CTRL0_XFER_COUNT(msg->len + 1); + desc = dmaengine_prep_slave_sg(i2c->dmach, + (struct scatterlist *)&i2c->pio_data[0], + 1, DMA_TRANS_NONE, 0); + if (!desc) { + dev_err(i2c->dev, + "Failed to get PIO reg. write descriptor.\n"); + goto write_init_pio_fail; + } + + /* Queue the DMA data transfer. */ + sg_init_table(i2c->sg_io, 2); + sg_set_buf(&i2c->sg_io[0], &i2c->addr_data, 1); + sg_set_buf(&i2c->sg_io[1], msg->buf, msg->len); + dma_map_sg(i2c->dev, i2c->sg_io, 2, DMA_TO_DEVICE); + desc = dmaengine_prep_slave_sg(i2c->dmach, i2c->sg_io, 2, + DMA_MEM_TO_DEV, + DMA_PREP_INTERRUPT | + MXS_DMA_CTRL_WAIT4END); + if (!desc) { + dev_err(i2c->dev, + "Failed to get DMA data write descriptor.\n"); + goto write_init_dma_fail; + } + } + + /* + * The last descriptor must have this callback, + * to finish the DMA transaction. + */ + desc->callback = mxs_i2c_dma_irq_callback; + desc->callback_param = i2c; + + /* Start the transfer. */ + dmaengine_submit(desc); + dma_async_issue_pending(i2c->dmach); + return 0; + +/* Read failpath. */ +read_init_dma_fail: + dma_unmap_sg(i2c->dev, &i2c->sg_io[1], 1, DMA_FROM_DEVICE); +select_init_dma_fail: + dma_unmap_sg(i2c->dev, &i2c->sg_io[0], 1, DMA_TO_DEVICE); +select_init_pio_fail: + dmaengine_terminate_all(i2c->dmach); + return -EINVAL; + +/* Write failpath. */ +write_init_dma_fail: + dma_unmap_sg(i2c->dev, i2c->sg_io, 2, DMA_TO_DEVICE); +write_init_pio_fail: + dmaengine_terminate_all(i2c->dmach); + return -EINVAL; +} + +static int mxs_i2c_pio_wait_xfer_end(struct mxs_i2c_dev *i2c) +{ + unsigned long timeout = jiffies + msecs_to_jiffies(1000); + + while (readl(i2c->regs + MXS_I2C_CTRL0) & MXS_I2C_CTRL0_RUN) { + if (readl(i2c->regs + MXS_I2C_CTRL1) & + MXS_I2C_CTRL1_NO_SLAVE_ACK_IRQ) + return -ENXIO; + if (time_after(jiffies, timeout)) + return -ETIMEDOUT; + cond_resched(); + } + + return 0; +} + +static int mxs_i2c_pio_check_error_state(struct mxs_i2c_dev *i2c) +{ + u32 state; + + state = readl(i2c->regs + MXS_I2C_CTRL1_CLR) & MXS_I2C_IRQ_MASK; + + if (state & MXS_I2C_CTRL1_NO_SLAVE_ACK_IRQ) + i2c->cmd_err = -ENXIO; + else if (state & (MXS_I2C_CTRL1_EARLY_TERM_IRQ | + MXS_I2C_CTRL1_MASTER_LOSS_IRQ | + MXS_I2C_CTRL1_SLAVE_STOP_IRQ | + MXS_I2C_CTRL1_SLAVE_IRQ)) + i2c->cmd_err = -EIO; + + return i2c->cmd_err; +} + +static void mxs_i2c_pio_trigger_cmd(struct mxs_i2c_dev *i2c, u32 cmd) +{ + u32 reg; + + writel(cmd, i2c->regs + MXS_I2C_CTRL0); + + /* readback makes sure the write is latched into hardware */ + reg = readl(i2c->regs + MXS_I2C_CTRL0); + reg |= MXS_I2C_CTRL0_RUN; + writel(reg, i2c->regs + MXS_I2C_CTRL0); +} + +/* + * Start WRITE transaction on the I2C bus. By studying i.MX23 datasheet, + * CTRL0::PIO_MODE bit description clarifies the order in which the registers + * must be written during PIO mode operation. First, the CTRL0 register has + * to be programmed with all the necessary bits but the RUN bit. Then the + * payload has to be written into the DATA register. Finally, the transmission + * is executed by setting the RUN bit in CTRL0. + */ +static void mxs_i2c_pio_trigger_write_cmd(struct mxs_i2c_dev *i2c, u32 cmd, + u32 data) +{ + writel(cmd, i2c->regs + MXS_I2C_CTRL0); + + if (i2c->dev_type == MXS_I2C_V1) + writel(MXS_I2C_CTRL0_PIO_MODE, i2c->regs + MXS_I2C_CTRL0_SET); + + writel(data, i2c->regs + MXS_I2C_DATA(i2c)); + writel(MXS_I2C_CTRL0_RUN, i2c->regs + MXS_I2C_CTRL0_SET); +} + +static int mxs_i2c_pio_setup_xfer(struct i2c_adapter *adap, + struct i2c_msg *msg, uint32_t flags) +{ + struct mxs_i2c_dev *i2c = i2c_get_adapdata(adap); + uint32_t addr_data = i2c_8bit_addr_from_msg(msg); + uint32_t data = 0; + int i, ret, xlen = 0, xmit = 0; + uint32_t start; + + /* Mute IRQs coming from this block. */ + writel(MXS_I2C_IRQ_MASK << 8, i2c->regs + MXS_I2C_CTRL1_CLR); + + /* + * MX23 idea: + * - Enable CTRL0::PIO_MODE (1 << 24) + * - Enable CTRL1::ACK_MODE (1 << 27) + * + * WARNING! The MX23 is broken in some way, even if it claims + * to support PIO, when we try to transfer any amount of data + * that is not aligned to 4 bytes, the DMA engine will have + * bits in DEBUG1::DMA_BYTES_ENABLES still set even after the + * transfer. This in turn will mess up the next transfer as + * the block it emit one byte write onto the bus terminated + * with a NAK+STOP. A possible workaround is to reset the IP + * block after every PIO transmission, which might just work. + * + * NOTE: The CTRL0::PIO_MODE description is important, since + * it outlines how the PIO mode is really supposed to work. + */ + if (msg->flags & I2C_M_RD) { + /* + * PIO READ transfer: + * + * This transfer MUST be limited to 4 bytes maximum. It is not + * possible to transfer more than four bytes via PIO, since we + * can not in any way make sure we can read the data from the + * DATA register fast enough. Besides, the RX FIFO is only four + * bytes deep, thus we can only really read up to four bytes at + * time. Finally, there is no bit indicating us that new data + * arrived at the FIFO and can thus be fetched from the DATA + * register. + */ + BUG_ON(msg->len > 4); + + /* SELECT command. */ + mxs_i2c_pio_trigger_write_cmd(i2c, MXS_CMD_I2C_SELECT, + addr_data); + + ret = mxs_i2c_pio_wait_xfer_end(i2c); + if (ret) { + dev_dbg(i2c->dev, + "PIO: Failed to send SELECT command!\n"); + goto cleanup; + } + + /* READ command. */ + mxs_i2c_pio_trigger_cmd(i2c, + MXS_CMD_I2C_READ | flags | + MXS_I2C_CTRL0_XFER_COUNT(msg->len)); + + ret = mxs_i2c_pio_wait_xfer_end(i2c); + if (ret) { + dev_dbg(i2c->dev, + "PIO: Failed to send READ command!\n"); + goto cleanup; + } + + data = readl(i2c->regs + MXS_I2C_DATA(i2c)); + for (i = 0; i < msg->len; i++) { + msg->buf[i] = data & 0xff; + data >>= 8; + } + } else { + /* + * PIO WRITE transfer: + * + * The code below implements clock stretching to circumvent + * the possibility of kernel not being able to supply data + * fast enough. It is possible to transfer arbitrary amount + * of data using PIO write. + */ + + /* + * The LSB of data buffer is the first byte blasted across + * the bus. Higher order bytes follow. Thus the following + * filling schematic. + */ + + data = addr_data << 24; + + /* Start the transfer with START condition. */ + start = MXS_I2C_CTRL0_PRE_SEND_START; + + /* If the transfer is long, use clock stretching. */ + if (msg->len > 3) + start |= MXS_I2C_CTRL0_RETAIN_CLOCK; + + for (i = 0; i < msg->len; i++) { + data >>= 8; + data |= (msg->buf[i] << 24); + + xmit = 0; + + /* This is the last transfer of the message. */ + if (i + 1 == msg->len) { + /* Add optional STOP flag. */ + start |= flags; + /* Remove RETAIN_CLOCK bit. */ + start &= ~MXS_I2C_CTRL0_RETAIN_CLOCK; + xmit = 1; + } + + /* Four bytes are ready in the "data" variable. */ + if ((i & 3) == 2) + xmit = 1; + + /* Nothing interesting happened, continue stuffing. */ + if (!xmit) + continue; + + /* + * Compute the size of the transfer and shift the + * data accordingly. + * + * i = (4k + 0) .... xlen = 2 + * i = (4k + 1) .... xlen = 3 + * i = (4k + 2) .... xlen = 4 + * i = (4k + 3) .... xlen = 1 + */ + + if ((i % 4) == 3) + xlen = 1; + else + xlen = (i % 4) + 2; + + data >>= (4 - xlen) * 8; + + dev_dbg(i2c->dev, + "PIO: len=%i pos=%i total=%i [W%s%s%s]\n", + xlen, i, msg->len, + start & MXS_I2C_CTRL0_PRE_SEND_START ? "S" : "", + start & MXS_I2C_CTRL0_POST_SEND_STOP ? "E" : "", + start & MXS_I2C_CTRL0_RETAIN_CLOCK ? "C" : ""); + + writel(MXS_I2C_DEBUG0_DMAREQ, + i2c->regs + MXS_I2C_DEBUG0_CLR(i2c)); + + mxs_i2c_pio_trigger_write_cmd(i2c, + start | MXS_I2C_CTRL0_MASTER_MODE | + MXS_I2C_CTRL0_DIRECTION | + MXS_I2C_CTRL0_XFER_COUNT(xlen), data); + + /* The START condition is sent only once. */ + start &= ~MXS_I2C_CTRL0_PRE_SEND_START; + + /* Wait for the end of the transfer. */ + ret = mxs_i2c_pio_wait_xfer_end(i2c); + if (ret) { + dev_dbg(i2c->dev, + "PIO: Failed to finish WRITE cmd!\n"); + break; + } + + /* Check NAK here. */ + ret = readl(i2c->regs + MXS_I2C_STAT) & + MXS_I2C_STAT_GOT_A_NAK; + if (ret) { + ret = -ENXIO; + goto cleanup; + } + } + } + + /* make sure we capture any occurred error into cmd_err */ + ret = mxs_i2c_pio_check_error_state(i2c); + +cleanup: + /* Clear any dangling IRQs and re-enable interrupts. */ + writel(MXS_I2C_IRQ_MASK, i2c->regs + MXS_I2C_CTRL1_CLR); + writel(MXS_I2C_IRQ_MASK << 8, i2c->regs + MXS_I2C_CTRL1_SET); + + /* Clear the PIO_MODE on i.MX23 */ + if (i2c->dev_type == MXS_I2C_V1) + writel(MXS_I2C_CTRL0_PIO_MODE, i2c->regs + MXS_I2C_CTRL0_CLR); + + return ret; +} + +/* + * Low level master read/write transaction. + */ +static int mxs_i2c_xfer_msg(struct i2c_adapter *adap, struct i2c_msg *msg, + int stop) +{ + struct mxs_i2c_dev *i2c = i2c_get_adapdata(adap); + int ret; + int flags; + int use_pio = 0; + unsigned long time_left; + + flags = stop ? MXS_I2C_CTRL0_POST_SEND_STOP : 0; + + dev_dbg(i2c->dev, "addr: 0x%04x, len: %d, flags: 0x%x, stop: %d\n", + msg->addr, msg->len, msg->flags, stop); + + /* + * The MX28 I2C IP block can only do PIO READ for transfer of to up + * 4 bytes of length. The write transfer is not limited as it can use + * clock stretching to avoid FIFO underruns. + */ + if ((msg->flags & I2C_M_RD) && (msg->len <= 4)) + use_pio = 1; + if (!(msg->flags & I2C_M_RD) && (msg->len < 7)) + use_pio = 1; + + i2c->cmd_err = 0; + if (use_pio) { + ret = mxs_i2c_pio_setup_xfer(adap, msg, flags); + /* No need to reset the block if NAK was received. */ + if (ret && (ret != -ENXIO)) + mxs_i2c_reset(i2c); + } else { + reinit_completion(&i2c->cmd_complete); + ret = mxs_i2c_dma_setup_xfer(adap, msg, flags); + if (ret) + return ret; + + time_left = wait_for_completion_timeout(&i2c->cmd_complete, + msecs_to_jiffies(1000)); + if (!time_left) + goto timeout; + + ret = i2c->cmd_err; + } + + if (ret == -ENXIO) { + /* + * If the transfer fails with a NAK from the slave the + * controller halts until it gets told to return to idle state. + */ + writel(MXS_I2C_CTRL1_CLR_GOT_A_NAK, + i2c->regs + MXS_I2C_CTRL1_SET); + } + + /* + * WARNING! + * The i.MX23 is strange. After each and every operation, it's I2C IP + * block must be reset, otherwise the IP block will misbehave. This can + * be observed on the bus by the block sending out one single byte onto + * the bus. In case such an error happens, bit 27 will be set in the + * DEBUG0 register. This bit is not documented in the i.MX23 datasheet + * and is marked as "TBD" instead. To reset this bit to a correct state, + * reset the whole block. Since the block reset does not take long, do + * reset the block after every transfer to play safe. + */ + if (i2c->dev_type == MXS_I2C_V1) + mxs_i2c_reset(i2c); + + dev_dbg(i2c->dev, "Done with err=%d\n", ret); + + return ret; + +timeout: + dev_dbg(i2c->dev, "Timeout!\n"); + mxs_i2c_dma_finish(i2c); + ret = mxs_i2c_reset(i2c); + if (ret) + return ret; + + return -ETIMEDOUT; +} + +static int mxs_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], + int num) +{ + int i; + int err; + + for (i = 0; i < num; i++) { + err = mxs_i2c_xfer_msg(adap, &msgs[i], i == (num - 1)); + if (err) + return err; + } + + return num; +} + +static u32 mxs_i2c_func(struct i2c_adapter *adap) +{ + return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL; +} + +static irqreturn_t mxs_i2c_isr(int this_irq, void *dev_id) +{ + struct mxs_i2c_dev *i2c = dev_id; + u32 stat = readl(i2c->regs + MXS_I2C_CTRL1) & MXS_I2C_IRQ_MASK; + + if (!stat) + return IRQ_NONE; + + if (stat & MXS_I2C_CTRL1_NO_SLAVE_ACK_IRQ) + i2c->cmd_err = -ENXIO; + else if (stat & (MXS_I2C_CTRL1_EARLY_TERM_IRQ | + MXS_I2C_CTRL1_MASTER_LOSS_IRQ | + MXS_I2C_CTRL1_SLAVE_STOP_IRQ | MXS_I2C_CTRL1_SLAVE_IRQ)) + /* MXS_I2C_CTRL1_OVERSIZE_XFER_TERM_IRQ is only for slaves */ + i2c->cmd_err = -EIO; + + writel(stat, i2c->regs + MXS_I2C_CTRL1_CLR); + + return IRQ_HANDLED; +} + +static const struct i2c_algorithm mxs_i2c_algo = { + .master_xfer = mxs_i2c_xfer, + .functionality = mxs_i2c_func, +}; + +static const struct i2c_adapter_quirks mxs_i2c_quirks = { + .flags = I2C_AQ_NO_ZERO_LEN, +}; + +static void mxs_i2c_derive_timing(struct mxs_i2c_dev *i2c, uint32_t speed) +{ + /* The I2C block clock runs at 24MHz */ + const uint32_t clk = 24000000; + uint32_t divider; + uint16_t high_count, low_count, rcv_count, xmit_count; + uint32_t bus_free, leadin; + struct device *dev = i2c->dev; + + divider = DIV_ROUND_UP(clk, speed); + + if (divider < 25) { + /* + * limit the divider, so that min(low_count, high_count) + * is >= 1 + */ + divider = 25; + dev_warn(dev, + "Speed too high (%u.%03u kHz), using %u.%03u kHz\n", + speed / 1000, speed % 1000, + clk / divider / 1000, clk / divider % 1000); + } else if (divider > 1897) { + /* + * limit the divider, so that max(low_count, high_count) + * cannot exceed 1023 + */ + divider = 1897; + dev_warn(dev, + "Speed too low (%u.%03u kHz), using %u.%03u kHz\n", + speed / 1000, speed % 1000, + clk / divider / 1000, clk / divider % 1000); + } + + /* + * The I2C spec specifies the following timing data: + * standard mode fast mode Bitfield name + * tLOW (SCL LOW period) 4700 ns 1300 ns + * tHIGH (SCL HIGH period) 4000 ns 600 ns + * tSU;DAT (data setup time) 250 ns 100 ns + * tHD;STA (START hold time) 4000 ns 600 ns + * tBUF (bus free time) 4700 ns 1300 ns + * + * The hardware (of the i.MX28 at least) seems to add 2 additional + * clock cycles to the low_count and 7 cycles to the high_count. + * This is compensated for by subtracting the respective constants + * from the values written to the timing registers. + */ + if (speed > I2C_MAX_STANDARD_MODE_FREQ) { + /* fast mode */ + low_count = DIV_ROUND_CLOSEST(divider * 13, (13 + 6)); + high_count = DIV_ROUND_CLOSEST(divider * 6, (13 + 6)); + leadin = DIV_ROUND_UP(600 * (clk / 1000000), 1000); + bus_free = DIV_ROUND_UP(1300 * (clk / 1000000), 1000); + } else { + /* normal mode */ + low_count = DIV_ROUND_CLOSEST(divider * 47, (47 + 40)); + high_count = DIV_ROUND_CLOSEST(divider * 40, (47 + 40)); + leadin = DIV_ROUND_UP(4700 * (clk / 1000000), 1000); + bus_free = DIV_ROUND_UP(4700 * (clk / 1000000), 1000); + } + rcv_count = high_count * 3 / 8; + xmit_count = low_count * 3 / 8; + + dev_dbg(dev, + "speed=%u(actual %u) divider=%u low=%u high=%u xmit=%u rcv=%u leadin=%u bus_free=%u\n", + speed, clk / divider, divider, low_count, high_count, + xmit_count, rcv_count, leadin, bus_free); + + low_count -= 2; + high_count -= 7; + i2c->timing0 = (high_count << 16) | rcv_count; + i2c->timing1 = (low_count << 16) | xmit_count; + i2c->timing2 = (bus_free << 16 | leadin); +} + +static int mxs_i2c_get_ofdata(struct mxs_i2c_dev *i2c) +{ + uint32_t speed; + struct device *dev = i2c->dev; + struct device_node *node = dev->of_node; + int ret; + + ret = of_property_read_u32(node, "clock-frequency", &speed); + if (ret) { + dev_warn(dev, "No I2C speed selected, using 100kHz\n"); + speed = I2C_MAX_STANDARD_MODE_FREQ; + } + + mxs_i2c_derive_timing(i2c, speed); + + return 0; +} + +static const struct platform_device_id mxs_i2c_devtype[] = { + { + .name = "imx23-i2c", + .driver_data = MXS_I2C_V1, + }, { + .name = "imx28-i2c", + .driver_data = MXS_I2C_V2, + }, { /* sentinel */ } +}; +MODULE_DEVICE_TABLE(platform, mxs_i2c_devtype); + +static const struct of_device_id mxs_i2c_dt_ids[] = { + { .compatible = "fsl,imx23-i2c", .data = &mxs_i2c_devtype[0], }, + { .compatible = "fsl,imx28-i2c", .data = &mxs_i2c_devtype[1], }, + { /* sentinel */ } +}; +MODULE_DEVICE_TABLE(of, mxs_i2c_dt_ids); + +static int mxs_i2c_probe(struct platform_device *pdev) +{ + const struct of_device_id *of_id = + of_match_device(mxs_i2c_dt_ids, &pdev->dev); + struct device *dev = &pdev->dev; + struct mxs_i2c_dev *i2c; + struct i2c_adapter *adap; + int err, irq; + + i2c = devm_kzalloc(dev, sizeof(*i2c), GFP_KERNEL); + if (!i2c) + return -ENOMEM; + + if (of_id) { + const struct platform_device_id *device_id = of_id->data; + i2c->dev_type = device_id->driver_data; + } + + i2c->regs = devm_platform_ioremap_resource(pdev, 0); + if (IS_ERR(i2c->regs)) + return PTR_ERR(i2c->regs); + + irq = platform_get_irq(pdev, 0); + if (irq < 0) + return irq; + + err = devm_request_irq(dev, irq, mxs_i2c_isr, 0, dev_name(dev), i2c); + if (err) + return err; + + i2c->dev = dev; + + init_completion(&i2c->cmd_complete); + + if (dev->of_node) { + err = mxs_i2c_get_ofdata(i2c); + if (err) + return err; + } + + /* Setup the DMA */ + i2c->dmach = dma_request_chan(dev, "rx-tx"); + if (IS_ERR(i2c->dmach)) { + return dev_err_probe(dev, PTR_ERR(i2c->dmach), + "Failed to request dma\n"); + } + + platform_set_drvdata(pdev, i2c); + + /* Do reset to enforce correct startup after pinmuxing */ + err = mxs_i2c_reset(i2c); + if (err) + return err; + + adap = &i2c->adapter; + strlcpy(adap->name, "MXS I2C adapter", sizeof(adap->name)); + adap->owner = THIS_MODULE; + adap->algo = &mxs_i2c_algo; + adap->quirks = &mxs_i2c_quirks; + adap->dev.parent = dev; + adap->nr = pdev->id; + adap->dev.of_node = pdev->dev.of_node; + i2c_set_adapdata(adap, i2c); + err = i2c_add_numbered_adapter(adap); + if (err) { + writel(MXS_I2C_CTRL0_SFTRST, + i2c->regs + MXS_I2C_CTRL0_SET); + return err; + } + + return 0; +} + +static int mxs_i2c_remove(struct platform_device *pdev) +{ + struct mxs_i2c_dev *i2c = platform_get_drvdata(pdev); + + i2c_del_adapter(&i2c->adapter); + + if (i2c->dmach) + dma_release_channel(i2c->dmach); + + writel(MXS_I2C_CTRL0_SFTRST, i2c->regs + MXS_I2C_CTRL0_SET); + + return 0; +} + +static struct platform_driver mxs_i2c_driver = { + .driver = { + .name = DRIVER_NAME, + .of_match_table = mxs_i2c_dt_ids, + }, + .probe = mxs_i2c_probe, + .remove = mxs_i2c_remove, +}; + +static int __init mxs_i2c_init(void) +{ + return platform_driver_register(&mxs_i2c_driver); +} +subsys_initcall(mxs_i2c_init); + +static void __exit mxs_i2c_exit(void) +{ + platform_driver_unregister(&mxs_i2c_driver); +} +module_exit(mxs_i2c_exit); + +MODULE_AUTHOR("Marek Vasut <marex@denx.de>"); +MODULE_AUTHOR("Wolfram Sang <kernel@pengutronix.de>"); +MODULE_DESCRIPTION("MXS I2C Bus Driver"); +MODULE_LICENSE("GPL"); +MODULE_ALIAS("platform:" DRIVER_NAME); |