diff options
Diffstat (limited to '')
| -rw-r--r-- | drivers/input/touchscreen/Kconfig | 1338 |
1 files changed, 1338 insertions, 0 deletions
diff --git a/drivers/input/touchscreen/Kconfig b/drivers/input/touchscreen/Kconfig new file mode 100644 index 000000000..cc18f54ea --- /dev/null +++ b/drivers/input/touchscreen/Kconfig @@ -0,0 +1,1338 @@ +# SPDX-License-Identifier: GPL-2.0-only +# +# Touchscreen driver configuration +# +menuconfig INPUT_TOUCHSCREEN + bool "Touchscreens" + help + Say Y here, and a list of supported touchscreens will be displayed. + This option doesn't affect the kernel. + + If unsure, say Y. + +if INPUT_TOUCHSCREEN + +config TOUCHSCREEN_PROPERTIES + def_tristate INPUT + depends on INPUT + +config TOUCHSCREEN_88PM860X + tristate "Marvell 88PM860x touchscreen" + depends on MFD_88PM860X + help + Say Y here if you have a 88PM860x PMIC and want to enable + support for the built-in touchscreen. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called 88pm860x-ts. + +config TOUCHSCREEN_ADS7846 + tristate "ADS7846/TSC2046/AD7873 and AD(S)7843 based touchscreens" + depends on SPI_MASTER + depends on HWMON = n || HWMON + help + Say Y here if you have a touchscreen interface using the + ADS7846/TSC2046/AD7873 or ADS7843/AD7843 controller, + and your board-specific setup code includes that in its + table of SPI devices. + + If HWMON is selected, and the driver is told the reference voltage + on your board, you will also get hwmon interfaces for the voltage + (and on ads7846/tsc2046/ad7873, temperature) sensors of this chip. + + If unsure, say N (but it's safe to say "Y"). + + To compile this driver as a module, choose M here: the + module will be called ads7846. + +config TOUCHSCREEN_AD7877 + tristate "AD7877 based touchscreens" + depends on SPI_MASTER + help + Say Y here if you have a touchscreen interface using the + AD7877 controller, and your board-specific initialization + code includes that in its table of SPI devices. + + If unsure, say N (but it's safe to say "Y"). + + To compile this driver as a module, choose M here: the + module will be called ad7877. + +config TOUCHSCREEN_AD7879 + tristate "Analog Devices AD7879-1/AD7889-1 touchscreen interface" + help + Say Y here if you want to support a touchscreen interface using + the AD7879-1/AD7889-1 controller. + + You should select a bus connection too. + + To compile this driver as a module, choose M here: the + module will be called ad7879. + +config TOUCHSCREEN_AD7879_I2C + tristate "support I2C bus connection" + depends on TOUCHSCREEN_AD7879 && I2C + select REGMAP_I2C + help + Say Y here if you have AD7879-1/AD7889-1 hooked to an I2C bus. + + To compile this driver as a module, choose M here: the + module will be called ad7879-i2c. + +config TOUCHSCREEN_AD7879_SPI + tristate "support SPI bus connection" + depends on TOUCHSCREEN_AD7879 && SPI_MASTER + select REGMAP_SPI + help + Say Y here if you have AD7879-1/AD7889-1 hooked to a SPI bus. + + If unsure, say N (but it's safe to say "Y"). + + To compile this driver as a module, choose M here: the + module will be called ad7879-spi. + +config TOUCHSCREEN_ADC + tristate "Generic ADC based resistive touchscreen" + depends on IIO + select IIO_BUFFER + select IIO_BUFFER_CB + help + Say Y here if you want to use the generic ADC + resistive touchscreen driver. + + If unsure, say N (but it's safe to say "Y"). + + To compile this driver as a module, choose M here: the + module will be called resistive-adc-touch.ko. + +config TOUCHSCREEN_AR1021_I2C + tristate "Microchip AR1020/1021 i2c touchscreen" + depends on I2C && OF + help + Say Y here if you have the Microchip AR1020 or AR1021 touchscreen + controller chip in your system. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called ar1021_i2c. + +config TOUCHSCREEN_ATMEL_MXT + tristate "Atmel mXT I2C Touchscreen" + depends on I2C + select FW_LOADER + help + Say Y here if you have Atmel mXT series I2C touchscreen, + such as AT42QT602240/ATMXT224, connected to your system. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called atmel_mxt_ts. + +config TOUCHSCREEN_ATMEL_MXT_T37 + bool "Support T37 Diagnostic Data" + depends on TOUCHSCREEN_ATMEL_MXT + depends on VIDEO_V4L2=y || (TOUCHSCREEN_ATMEL_MXT=m && VIDEO_V4L2=m) + select VIDEOBUF2_VMALLOC + help + Say Y here if you want support to output data from the T37 + Diagnostic Data object using a V4L device. + +config TOUCHSCREEN_AUO_PIXCIR + tristate "AUO in-cell touchscreen using Pixcir ICs" + depends on I2C + depends on GPIOLIB || COMPILE_TEST + help + Say Y here if you have a AUO display with in-cell touchscreen + using Pixcir ICs. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called auo-pixcir-ts. + +config TOUCHSCREEN_BU21013 + tristate "BU21013 based touch panel controllers" + depends on I2C + help + Say Y here if you have a bu21013 touchscreen connected to + your system. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called bu21013_ts. + +config TOUCHSCREEN_BU21029 + tristate "Rohm BU21029 based touch panel controllers" + depends on I2C + help + Say Y here if you have a Rohm BU21029 touchscreen controller + connected to your system. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called bu21029_ts. + +config TOUCHSCREEN_CHIPONE_ICN8318 + tristate "chipone icn8318 touchscreen controller" + depends on GPIOLIB || COMPILE_TEST + depends on I2C + depends on OF + help + Say Y here if you have a ChipOne icn8318 based I2C touchscreen. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called chipone_icn8318. + +config TOUCHSCREEN_CHIPONE_ICN8505 + tristate "chipone icn8505 touchscreen controller" + depends on I2C && ACPI + help + Say Y here if you have a ChipOne icn8505 based I2C touchscreen. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called chipone_icn8505. + +config TOUCHSCREEN_CY8CTMA140 + tristate "cy8ctma140 touchscreen" + depends on I2C + help + Say Y here if you have a Cypress CY8CTMA140 capacitive + touchscreen also just known as "TMA140" + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called cy8ctma140. + +config TOUCHSCREEN_CY8CTMG110 + tristate "cy8ctmg110 touchscreen" + depends on I2C + depends on GPIOLIB || COMPILE_TEST + help + Say Y here if you have a cy8ctmg110 capacitive touchscreen on + an AAVA device. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called cy8ctmg110_ts. + +config TOUCHSCREEN_CYTTSP_CORE + tristate "Cypress TTSP touchscreen" + help + Say Y here if you have a touchscreen using controller from + the Cypress TrueTouch(tm) Standard Product family connected + to your system. You will also need to select appropriate + bus connection below. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called cyttsp_core. + +config TOUCHSCREEN_CYTTSP_I2C + tristate "support I2C bus connection" + depends on TOUCHSCREEN_CYTTSP_CORE && I2C + help + Say Y here if the touchscreen is connected via I2C bus. + + To compile this driver as a module, choose M here: the + module will be called cyttsp_i2c. + +config TOUCHSCREEN_CYTTSP_SPI + tristate "support SPI bus connection" + depends on TOUCHSCREEN_CYTTSP_CORE && SPI_MASTER + help + Say Y here if the touchscreen is connected via SPI bus. + + To compile this driver as a module, choose M here: the + module will be called cyttsp_spi. + +config TOUCHSCREEN_CYTTSP4_CORE + tristate "Cypress TrueTouch Gen4 Touchscreen Driver" + help + Core driver for Cypress TrueTouch(tm) Standard Product + Generation4 touchscreen controllers. + + Say Y here if you have a Cypress Gen4 touchscreen. + + If unsure, say N. + + To compile this driver as a module, choose M here. + +config TOUCHSCREEN_CYTTSP4_I2C + tristate "support I2C bus connection" + depends on TOUCHSCREEN_CYTTSP4_CORE && I2C + help + Say Y here if the touchscreen is connected via I2C bus. + + To compile this driver as a module, choose M here: the + module will be called cyttsp4_i2c. + +config TOUCHSCREEN_CYTTSP4_SPI + tristate "support SPI bus connection" + depends on TOUCHSCREEN_CYTTSP4_CORE && SPI_MASTER + help + Say Y here if the touchscreen is connected via SPI bus. + + To compile this driver as a module, choose M here: the + module will be called cyttsp4_spi. + +config TOUCHSCREEN_DA9034 + tristate "Touchscreen support for Dialog Semiconductor DA9034" + depends on PMIC_DA903X + default y + help + Say Y here to enable the support for the touchscreen found + on Dialog Semiconductor DA9034 PMIC. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called da9034-ts. + +config TOUCHSCREEN_DA9052 + tristate "Dialog DA9052/DA9053 TSI" + depends on PMIC_DA9052 + help + Say Y here to support the touchscreen found on Dialog Semiconductor + DA9052-BC and DA9053-AA/Bx PMICs. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called da9052_tsi. + +config TOUCHSCREEN_DYNAPRO + tristate "Dynapro serial touchscreen" + select SERIO + help + Say Y here if you have a Dynapro serial touchscreen connected to + your system. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called dynapro. + +config TOUCHSCREEN_HAMPSHIRE + tristate "Hampshire serial touchscreen" + select SERIO + help + Say Y here if you have a Hampshire serial touchscreen connected to + your system. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called hampshire. + +config TOUCHSCREEN_EETI + tristate "EETI touchscreen panel support" + depends on I2C + help + Say Y here to enable support for I2C connected EETI touch panels. + + To compile this driver as a module, choose M here: the + module will be called eeti_ts. + +config TOUCHSCREEN_EGALAX + tristate "EETI eGalax multi-touch panel support" + depends on I2C && OF + help + Say Y here to enable support for I2C connected EETI + eGalax multi-touch panels. + + To compile this driver as a module, choose M here: the + module will be called egalax_ts. + +config TOUCHSCREEN_EGALAX_SERIAL + tristate "EETI eGalax serial touchscreen" + select SERIO + help + Say Y here to enable support for serial connected EETI + eGalax touch panels. + + To compile this driver as a module, choose M here: the + module will be called egalax_ts_serial. + +config TOUCHSCREEN_EXC3000 + tristate "EETI EXC3000 multi-touch panel support" + depends on I2C + help + Say Y here to enable support for I2C connected EETI + EXC3000 multi-touch panels. + + To compile this driver as a module, choose M here: the + module will be called exc3000. + +config TOUCHSCREEN_FUJITSU + tristate "Fujitsu serial touchscreen" + select SERIO + help + Say Y here if you have the Fujitsu touchscreen (such as one + installed in Lifebook P series laptop) connected to your + system. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called fujitsu-ts. + +config TOUCHSCREEN_GOODIX + tristate "Goodix I2C touchscreen" + depends on I2C + depends on GPIOLIB || COMPILE_TEST + help + Say Y here if you have the Goodix touchscreen (such as one + installed in Onda v975w tablets) connected to your + system. It also supports 5-finger chip models, which can be + found on ARM tablets, like Wexler TAB7200 and MSI Primo73. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called goodix. + +config TOUCHSCREEN_HIDEEP + tristate "HiDeep Touch IC" + depends on I2C + help + Say Y here if you have a touchscreen using HiDeep. + + If unsure, say N. + + To compile this driver as a module, choose M here : the + module will be called hideep_ts. + +config TOUCHSCREEN_ILI210X + tristate "Ilitek ILI210X based touchscreen" + depends on I2C + help + Say Y here if you have a ILI210X based touchscreen + controller. This driver supports models ILI2102, + ILI2102s, ILI2103, ILI2103s and ILI2105. + Such kind of chipsets can be found in Amazon Kindle Fire + touchscreens. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called ili210x. + +config TOUCHSCREEN_IPROC + tristate "IPROC touch panel driver support" + depends on ARCH_BCM_IPROC || COMPILE_TEST + help + Say Y here if you want to add support for the IPROC touch + controller to your system. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called bcm_iproc_tsc. + +config TOUCHSCREEN_S3C2410 + tristate "Samsung S3C2410/generic touchscreen input driver" + depends on ARCH_S3C24XX || SAMSUNG_DEV_TS + depends on S3C_ADC + help + Say Y here if you have the s3c2410 touchscreen. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called s3c2410_ts. + +config TOUCHSCREEN_S6SY761 + tristate "Samsung S6SY761 Touchscreen driver" + depends on I2C + help + Say Y if you have the Samsung S6SY761 driver + + If unsure, say N + + To compile this driver as module, choose M here: the + module will be called s6sy761. + +config TOUCHSCREEN_GUNZE + tristate "Gunze AHL-51S touchscreen" + select SERIO + help + Say Y here if you have the Gunze AHL-51 touchscreen connected to + your system. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called gunze. + +config TOUCHSCREEN_EKTF2127 + tristate "Elan eKTF2127 I2C touchscreen" + depends on I2C + help + Say Y here if you have an Elan eKTF2127 touchscreen + connected to your system. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called ektf2127. + +config TOUCHSCREEN_ELAN + tristate "Elan eKTH I2C touchscreen" + depends on I2C + help + Say Y here if you have an Elan eKTH I2C touchscreen + connected to your system. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called elants_i2c. + +config TOUCHSCREEN_ELO + tristate "Elo serial touchscreens" + select SERIO + help + Say Y here if you have an Elo serial touchscreen connected to + your system. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called elo. + +config TOUCHSCREEN_WACOM_W8001 + tristate "Wacom W8001 penabled serial touchscreen" + select SERIO + help + Say Y here if you have an Wacom W8001 penabled serial touchscreen + connected to your system. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called wacom_w8001. + +config TOUCHSCREEN_WACOM_I2C + tristate "Wacom Tablet support (I2C)" + depends on I2C + help + Say Y here if you want to use the I2C version of the Wacom + Pen Tablet. + + If unsure, say N. + + To compile this driver as a module, choose M here: the module + will be called wacom_i2c. + +config TOUCHSCREEN_LPC32XX + tristate "LPC32XX touchscreen controller" + depends on ARCH_LPC32XX + help + Say Y here if you have a LPC32XX device and want + to support the built-in touchscreen. + + To compile this driver as a module, choose M here: the + module will be called lpc32xx_ts. + +config TOUCHSCREEN_MAX11801 + tristate "MAX11801 based touchscreens" + depends on I2C + help + Say Y here if you have a MAX11801 based touchscreen + controller. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called max11801_ts. + +config TOUCHSCREEN_MCS5000 + tristate "MELFAS MCS-5000 touchscreen" + depends on I2C + help + Say Y here if you have the MELFAS MCS-5000 touchscreen controller + chip in your system. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called mcs5000_ts. + +config TOUCHSCREEN_MMS114 + tristate "MELFAS MMS114 touchscreen" + depends on I2C + help + Say Y here if you have the MELFAS MMS114 touchscreen controller + chip in your system. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called mms114. + +config TOUCHSCREEN_MELFAS_MIP4 + tristate "MELFAS MIP4 Touchscreen" + depends on I2C + help + Say Y here if you have a MELFAS MIP4 Touchscreen device. + + If unsure, say N. + + To compile this driver as a module, choose M here: + the module will be called melfas_mip4. + +config TOUCHSCREEN_MTOUCH + tristate "MicroTouch serial touchscreens" + select SERIO + help + Say Y here if you have a MicroTouch (3M) serial touchscreen connected to + your system. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called mtouch. + +config TOUCHSCREEN_IMX6UL_TSC + tristate "Freescale i.MX6UL touchscreen controller" + depends on (OF && GPIOLIB) || COMPILE_TEST + help + Say Y here if you have a Freescale i.MX6UL, and want to + use the internal touchscreen controller. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called imx6ul_tsc. + +config TOUCHSCREEN_INEXIO + tristate "iNexio serial touchscreens" + select SERIO + help + Say Y here if you have an iNexio serial touchscreen connected to + your system. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called inexio. + +config TOUCHSCREEN_MK712 + tristate "ICS MicroClock MK712 touchscreen" + help + Say Y here if you have the ICS MicroClock MK712 touchscreen + controller chip in your system. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called mk712. + +config TOUCHSCREEN_HP600 + tristate "HP Jornada 6xx touchscreen" + depends on SH_HP6XX && SH_ADC + help + Say Y here if you have a HP Jornada 620/660/680/690 and want to + support the built-in touchscreen. + + To compile this driver as a module, choose M here: the + module will be called hp680_ts_input. + +config TOUCHSCREEN_HP7XX + tristate "HP Jornada 7xx touchscreen" + depends on SA1100_JORNADA720_SSP + help + Say Y here if you have a HP Jornada 710/720/728 and want + to support the built-in touchscreen. + + To compile this driver as a module, choose M here: the + module will be called jornada720_ts. + +config TOUCHSCREEN_IPAQ_MICRO + tristate "HP iPAQ Atmel Micro ASIC touchscreen" + depends on MFD_IPAQ_MICRO + help + Say Y here to enable support for the touchscreen attached to + the Atmel Micro peripheral controller on iPAQ h3100/h3600/h3700 + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called ipaq-micro-ts. + +config TOUCHSCREEN_HTCPEN + tristate "HTC Shift X9500 touchscreen" + depends on ISA + help + Say Y here if you have an HTC Shift UMPC also known as HTC X9500 + Clio / Shangrila and want to support the built-in touchscreen. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called htcpen. + +config TOUCHSCREEN_PENMOUNT + tristate "Penmount serial touchscreen" + select SERIO + help + Say Y here if you have a Penmount serial touchscreen connected to + your system. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called penmount. + +config TOUCHSCREEN_EDT_FT5X06 + tristate "EDT FocalTech FT5x06 I2C Touchscreen support" + depends on I2C + help + Say Y here if you have an EDT "Polytouch" touchscreen based + on the FocalTech FT5x06 family of controllers connected to + your system. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called edt-ft5x06. + +config TOUCHSCREEN_RASPBERRYPI_FW + tristate "Raspberry Pi's firmware base touch screen support" + depends on RASPBERRYPI_FIRMWARE || (RASPBERRYPI_FIRMWARE=n && COMPILE_TEST) + help + Say Y here if you have the official Raspberry Pi 7 inch screen on + your system. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called raspberrypi-ts. + +config TOUCHSCREEN_MIGOR + tristate "Renesas MIGO-R touchscreen" + depends on (SH_MIGOR || COMPILE_TEST) && I2C + help + Say Y here to enable MIGO-R touchscreen support. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called migor_ts. + +config TOUCHSCREEN_TOUCHRIGHT + tristate "Touchright serial touchscreen" + select SERIO + help + Say Y here if you have a Touchright serial touchscreen connected to + your system. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called touchright. + +config TOUCHSCREEN_TOUCHWIN + tristate "Touchwin serial touchscreen" + select SERIO + help + Say Y here if you have a Touchwin serial touchscreen connected to + your system. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called touchwin. + +config TOUCHSCREEN_TI_AM335X_TSC + tristate "TI Touchscreen Interface" + depends on MFD_TI_AM335X_TSCADC + help + Say Y here if you have 4/5/8 wire touchscreen controller + to be connected to the ADC controller on your TI AM335x SoC. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called ti_am335x_tsc. + +config TOUCHSCREEN_UCB1400 + tristate "Philips UCB1400 touchscreen" + depends on AC97_BUS + depends on UCB1400_CORE + help + This enables support for the Philips UCB1400 touchscreen interface. + The UCB1400 is an AC97 audio codec. The touchscreen interface + will be initialized only after the ALSA subsystem has been + brought up and the UCB1400 detected. You therefore have to + configure ALSA support as well (either built-in or modular, + independently of whether this driver is itself built-in or + modular) for this driver to work. + + To compile this driver as a module, choose M here: the + module will be called ucb1400_ts. + +config TOUCHSCREEN_PIXCIR + tristate "PIXCIR I2C touchscreens" + depends on I2C + help + Say Y here if you have a pixcir i2c touchscreen + controller. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called pixcir_i2c_ts. + +config TOUCHSCREEN_WDT87XX_I2C + tristate "Weida HiTech I2C touchscreen" + depends on I2C + help + Say Y here if you have a Weida WDT87XX I2C touchscreen + connected to your system. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called wdt87xx_i2c. + +config TOUCHSCREEN_WM831X + tristate "Support for WM831x touchscreen controllers" + depends on MFD_WM831X + help + This enables support for the touchscreen controller on the WM831x + series of PMICs. + + To compile this driver as a module, choose M here: the + module will be called wm831x-ts. + +config TOUCHSCREEN_WM97XX + tristate "Support for WM97xx AC97 touchscreen controllers" + depends on AC97_BUS || AC97_BUS_NEW + help + Say Y here if you have a Wolfson Microelectronics WM97xx + touchscreen connected to your system. Note that this option + only enables core driver, you will also need to select + support for appropriate chip below. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called wm97xx-ts. + +config TOUCHSCREEN_WM9705 + bool "WM9705 Touchscreen interface support" + depends on TOUCHSCREEN_WM97XX + default y + help + Say Y here to enable support for the Wolfson Microelectronics + WM9705 touchscreen controller. + +config TOUCHSCREEN_WM9712 + bool "WM9712 Touchscreen interface support" + depends on TOUCHSCREEN_WM97XX + default y + help + Say Y here to enable support for the Wolfson Microelectronics + WM9712 touchscreen controller. + +config TOUCHSCREEN_WM9713 + bool "WM9713 Touchscreen interface support" + depends on TOUCHSCREEN_WM97XX + default y + help + Say Y here to enable support for the Wolfson Microelectronics + WM9713 touchscreen controller. + +config TOUCHSCREEN_WM97XX_MAINSTONE + tristate "WM97xx Mainstone/Palm accelerated touch" + depends on TOUCHSCREEN_WM97XX && ARCH_PXA + help + Say Y here for support for streaming mode with WM97xx touchscreens + on Mainstone, Palm Tungsten T5, TX and LifeDrive systems. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called mainstone-wm97xx. + +config TOUCHSCREEN_WM97XX_ZYLONITE + tristate "Zylonite accelerated touch" + depends on TOUCHSCREEN_WM97XX && MACH_ZYLONITE + select TOUCHSCREEN_WM9713 + help + Say Y here for support for streaming mode with the touchscreen + on Zylonite systems. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called zylonite-wm97xx. + +config TOUCHSCREEN_USB_COMPOSITE + tristate "USB Touchscreen Driver" + depends on USB_ARCH_HAS_HCD + select USB + help + USB Touchscreen driver for: + - eGalax Touchkit USB (also includes eTurboTouch CT-410/510/700) + - PanJit TouchSet USB + - 3M MicroTouch USB (EX II series) + - ITM + - some other eTurboTouch + - Gunze AHL61 + - DMC TSC-10/25 + - IRTOUCHSYSTEMS/UNITOP + - IdealTEK URTC1000 + - GoTop Super_Q2/GogoPen/PenPower tablets + - JASTEC USB Touch Controller/DigiTech DTR-02U + - Zytronic controllers + - Elo TouchSystems 2700 IntelliTouch + - EasyTouch USB Touch Controller from Data Modul + - e2i (Mimo monitors) + + Have a look at <http://linux.chapter7.ch/touchkit/> for + a usage description and the required user-space stuff. + + To compile this driver as a module, choose M here: the + module will be called usbtouchscreen. + +config TOUCHSCREEN_MXS_LRADC + tristate "Freescale i.MX23/i.MX28 LRADC touchscreen" + depends on MFD_MXS_LRADC + help + Say Y here if you have a touchscreen connected to the low-resolution + analog-to-digital converter (LRADC) on an i.MX23 or i.MX28 processor. + + To compile this driver as a module, choose M here: the module will be + called mxs-lradc-ts. + +config TOUCHSCREEN_MX25 + tristate "Freescale i.MX25 touchscreen input driver" + depends on MFD_MX25_TSADC + help + Enable support for touchscreen connected to your i.MX25. + + To compile this driver as a module, choose M here: the + module will be called fsl-imx25-tcq. + +config TOUCHSCREEN_MC13783 + tristate "Freescale MC13783 touchscreen input driver" + depends on MFD_MC13XXX + help + Say Y here if you have an Freescale MC13783 PMIC on your + board and want to use its touchscreen + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called mc13783_ts. + +config TOUCHSCREEN_USB_EGALAX + default y + bool "eGalax, eTurboTouch CT-410/510/700 device support" if EXPERT + depends on TOUCHSCREEN_USB_COMPOSITE + +config TOUCHSCREEN_USB_PANJIT + default y + bool "PanJit device support" if EXPERT + depends on TOUCHSCREEN_USB_COMPOSITE + +config TOUCHSCREEN_USB_3M + default y + bool "3M/Microtouch EX II series device support" if EXPERT + depends on TOUCHSCREEN_USB_COMPOSITE + +config TOUCHSCREEN_USB_ITM + default y + bool "ITM device support" if EXPERT + depends on TOUCHSCREEN_USB_COMPOSITE + +config TOUCHSCREEN_USB_ETURBO + default y + bool "eTurboTouch (non-eGalax compatible) device support" if EXPERT + depends on TOUCHSCREEN_USB_COMPOSITE + +config TOUCHSCREEN_USB_GUNZE + default y + bool "Gunze AHL61 device support" if EXPERT + depends on TOUCHSCREEN_USB_COMPOSITE + +config TOUCHSCREEN_USB_DMC_TSC10 + default y + bool "DMC TSC-10/25 device support" if EXPERT + depends on TOUCHSCREEN_USB_COMPOSITE + +config TOUCHSCREEN_USB_IRTOUCH + default y + bool "IRTOUCHSYSTEMS/UNITOP device support" if EXPERT + depends on TOUCHSCREEN_USB_COMPOSITE + +config TOUCHSCREEN_USB_IDEALTEK + default y + bool "IdealTEK URTC1000 device support" if EXPERT + depends on TOUCHSCREEN_USB_COMPOSITE + +config TOUCHSCREEN_USB_GENERAL_TOUCH + default y + bool "GeneralTouch Touchscreen device support" if EXPERT + depends on TOUCHSCREEN_USB_COMPOSITE + +config TOUCHSCREEN_USB_GOTOP + default y + bool "GoTop Super_Q2/GogoPen/PenPower tablet device support" if EXPERT + depends on TOUCHSCREEN_USB_COMPOSITE + +config TOUCHSCREEN_USB_JASTEC + default y + bool "JASTEC/DigiTech DTR-02U USB touch controller device support" if EXPERT + depends on TOUCHSCREEN_USB_COMPOSITE + +config TOUCHSCREEN_USB_ELO + default y + bool "Elo TouchSystems 2700 IntelliTouch controller device support" if EXPERT + depends on TOUCHSCREEN_USB_COMPOSITE + +config TOUCHSCREEN_USB_E2I + default y + bool "e2i Touchscreen controller (e.g. from Mimo 740)" if EXPERT + depends on TOUCHSCREEN_USB_COMPOSITE + +config TOUCHSCREEN_USB_ZYTRONIC + default y + bool "Zytronic controller" if EXPERT + depends on TOUCHSCREEN_USB_COMPOSITE + +config TOUCHSCREEN_USB_ETT_TC45USB + default y + bool "ET&T USB series TC4UM/TC5UH touchscreen controller support" if EXPERT + depends on TOUCHSCREEN_USB_COMPOSITE + +config TOUCHSCREEN_USB_NEXIO + default y + bool "NEXIO/iNexio device support" if EXPERT + depends on TOUCHSCREEN_USB_COMPOSITE + +config TOUCHSCREEN_USB_EASYTOUCH + default y + bool "EasyTouch USB Touch controller device support" if EXPERT + depends on TOUCHSCREEN_USB_COMPOSITE + help + Say Y here if you have an EasyTouch USB Touch controller. + If unsure, say N. + +config TOUCHSCREEN_TOUCHIT213 + tristate "Sahara TouchIT-213 touchscreen" + select SERIO + help + Say Y here if you have a Sahara TouchIT-213 Tablet PC. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called touchit213. + +config TOUCHSCREEN_TS4800 + tristate "TS-4800 touchscreen" + depends on HAS_IOMEM && OF + depends on SOC_IMX51 || COMPILE_TEST + select MFD_SYSCON + help + Say Y here if you have a touchscreen on a TS-4800 board. + + On TS-4800, the touchscreen is not handled directly by Linux but by + a companion FPGA. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called ts4800_ts. + +config TOUCHSCREEN_TSC_SERIO + tristate "TSC-10/25/40 serial touchscreen support" + select SERIO + help + Say Y here if you have a TSC-10, 25 or 40 serial touchscreen connected + to your system. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called tsc40. + +config TOUCHSCREEN_TSC200X_CORE + tristate + +config TOUCHSCREEN_TSC2004 + tristate "TSC2004 based touchscreens" + depends on I2C + select REGMAP_I2C + select TOUCHSCREEN_TSC200X_CORE + help + Say Y here if you have a TSC2004 based touchscreen. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called tsc2004. + +config TOUCHSCREEN_TSC2005 + tristate "TSC2005 based touchscreens" + depends on SPI_MASTER + select REGMAP_SPI + select TOUCHSCREEN_TSC200X_CORE + help + Say Y here if you have a TSC2005 based touchscreen. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called tsc2005. + +config TOUCHSCREEN_TSC2007 + tristate "TSC2007 based touchscreens" + depends on I2C + help + Say Y here if you have a TSC2007 based touchscreen. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called tsc2007. + +config TOUCHSCREEN_TSC2007_IIO + bool "IIO interface for external ADC input and temperature" + depends on TOUCHSCREEN_TSC2007 + depends on IIO=y || IIO=TOUCHSCREEN_TSC2007 + help + Saying Y here adds an iio interface to the tsc2007 which + provides values for the AUX input (used for e.g. battery + or ambient light monitoring), temperature and raw input + values. + +config TOUCHSCREEN_PCAP + tristate "Motorola PCAP touchscreen" + depends on EZX_PCAP + help + Say Y here if you have a Motorola EZX telephone and + want to enable support for the built-in touchscreen. + + To compile this driver as a module, choose M here: the + module will be called pcap_ts. + +config TOUCHSCREEN_RM_TS + tristate "Raydium I2C Touchscreen" + depends on I2C + depends on GPIOLIB || COMPILE_TEST + help + Say Y here if you have Raydium series I2C touchscreen, + such as RM32380, connected to your system. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called raydium_i2c_ts. + +config TOUCHSCREEN_SILEAD + tristate "Silead I2C touchscreen" + depends on I2C + help + Say Y here if you have the Silead touchscreen connected to + your system. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called silead. + +config TOUCHSCREEN_SIS_I2C + tristate "SiS 9200 family I2C touchscreen" + depends on I2C + select CRC_ITU_T + depends on GPIOLIB || COMPILE_TEST + help + This enables support for SiS 9200 family over I2C based touchscreens. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called sis_i2c. + +config TOUCHSCREEN_ST1232 + tristate "Sitronix ST1232 or ST1633 touchscreen controllers" + depends on I2C + help + Say Y here if you want to support the Sitronix ST1232 + or ST1633 touchscreen controller. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called st1232_ts. + +config TOUCHSCREEN_STMFTS + tristate "STMicroelectronics STMFTS touchscreen" + depends on I2C + depends on LEDS_CLASS + help + Say Y here if you want support for STMicroelectronics + STMFTS touchscreen. + + To compile this driver as a module, choose M here: the + module will be called stmfts. + +config TOUCHSCREEN_STMPE + tristate "STMicroelectronics STMPE touchscreens" + depends on MFD_STMPE + depends on (OF || COMPILE_TEST) + help + Say Y here if you want support for STMicroelectronics + STMPE touchscreen controllers. + + To compile this driver as a module, choose M here: the + module will be called stmpe-ts. + +config TOUCHSCREEN_SUN4I + tristate "Allwinner sun4i resistive touchscreen controller support" + depends on ARCH_SUNXI || COMPILE_TEST + depends on HWMON + depends on THERMAL || !THERMAL_OF + help + This selects support for the resistive touchscreen controller + found on Allwinner sunxi SoCs. + + To compile this driver as a module, choose M here: the + module will be called sun4i-ts. + +config TOUCHSCREEN_SUR40 + tristate "Samsung SUR40 (Surface 2.0/PixelSense) touchscreen" + depends on USB && MEDIA_USB_SUPPORT && HAS_DMA + depends on VIDEO_V4L2 + select VIDEOBUF2_DMA_SG + help + Say Y here if you want support for the Samsung SUR40 touchscreen + (also known as Microsoft Surface 2.0 or Microsoft PixelSense). + + To compile this driver as a module, choose M here: the + module will be called sur40. + +config TOUCHSCREEN_SURFACE3_SPI + tristate "Ntrig/Microsoft Surface 3 SPI touchscreen" + depends on SPI + depends on GPIOLIB || COMPILE_TEST + help + Say Y here if you have the Ntrig/Microsoft SPI touchscreen + controller chip as found on the Surface 3 in your system. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called surface3_spi. + +config TOUCHSCREEN_SX8654 + tristate "Semtech SX8654 touchscreen" + depends on I2C + help + Say Y here if you have a Semtech SX8654 touchscreen controller. + + If unsure, say N + + To compile this driver as a module, choose M here: the + module will be called sx8654. + +config TOUCHSCREEN_TPS6507X + tristate "TPS6507x based touchscreens" + depends on I2C + help + Say Y here if you have a TPS6507x based touchscreen + controller. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called tps6507x_ts. + +config TOUCHSCREEN_ZET6223 + tristate "Zeitec ZET6223 touchscreen driver" + depends on I2C + help + Say Y here if you have a touchscreen using Zeitec ZET6223 + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called zet6223. + +config TOUCHSCREEN_ZFORCE + tristate "Neonode zForce infrared touchscreens" + depends on I2C + depends on GPIOLIB || COMPILE_TEST + help + Say Y here if you have a touchscreen using the zforce + infraread technology from Neonode. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called zforce_ts. + +config TOUCHSCREEN_COLIBRI_VF50 + tristate "Toradex Colibri on board touchscreen driver" + depends on IIO && VF610_ADC + depends on GPIOLIB || COMPILE_TEST + help + Say Y here if you have a Colibri VF50 and plan to use + the on-board provided 4-wire touchscreen driver. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called colibri_vf50_ts. + +config TOUCHSCREEN_ROHM_BU21023 + tristate "ROHM BU21023/24 Dual touch support resistive touchscreens" + depends on I2C + help + Say Y here if you have a touchscreen using ROHM BU21023/24. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called bu21023_ts. + +config TOUCHSCREEN_IQS5XX + tristate "Azoteq IQS550/572/525 trackpad/touchscreen controller" + depends on I2C + help + Say Y to enable support for the Azoteq IQS550/572/525 + family of trackpad/touchscreen controllers. + + To compile this driver as a module, choose M here: the + module will be called iqs5xx. + +config TOUCHSCREEN_ZINITIX + tristate "Zinitix touchscreen support" + depends on I2C + help + Say Y here if you have a touchscreen using Zinitix bt541, + or something similar enough. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called zinitix. + +endif |