diff options
Diffstat (limited to 'drivers/media/rc/winbond-cir.c')
| -rw-r--r-- | drivers/media/rc/winbond-cir.c | 1221 |
1 files changed, 1221 insertions, 0 deletions
diff --git a/drivers/media/rc/winbond-cir.c b/drivers/media/rc/winbond-cir.c new file mode 100644 index 000000000..aed23ca0f --- /dev/null +++ b/drivers/media/rc/winbond-cir.c @@ -0,0 +1,1221 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * winbond-cir.c - Driver for the Consumer IR functionality of Winbond + * SuperI/O chips. + * + * Currently supports the Winbond WPCD376i chip (PNP id WEC1022), but + * could probably support others (Winbond WEC102X, NatSemi, etc) + * with minor modifications. + * + * Original Author: David Härdeman <david@hardeman.nu> + * Copyright (C) 2012 Sean Young <sean@mess.org> + * Copyright (C) 2009 - 2011 David Härdeman <david@hardeman.nu> + * + * Dedicated to my daughter Matilda, without whose loving attention this + * driver would have been finished in half the time and with a fraction + * of the bugs. + * + * Written using: + * o Winbond WPCD376I datasheet helpfully provided by Jesse Barnes at Intel + * o NatSemi PC87338/PC97338 datasheet (for the serial port stuff) + * o DSDT dumps + * + * Supported features: + * o IR Receive + * o IR Transmit + * o Wake-On-CIR functionality + * o Carrier detection + */ + +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt + +#include <linux/module.h> +#include <linux/pnp.h> +#include <linux/interrupt.h> +#include <linux/timer.h> +#include <linux/leds.h> +#include <linux/spinlock.h> +#include <linux/pci_ids.h> +#include <linux/io.h> +#include <linux/bitrev.h> +#include <linux/slab.h> +#include <linux/wait.h> +#include <linux/sched.h> +#include <media/rc-core.h> + +#define DRVNAME "winbond-cir" + +/* CEIR Wake-Up Registers, relative to data->wbase */ +#define WBCIR_REG_WCEIR_CTL 0x03 /* CEIR Receiver Control */ +#define WBCIR_REG_WCEIR_STS 0x04 /* CEIR Receiver Status */ +#define WBCIR_REG_WCEIR_EV_EN 0x05 /* CEIR Receiver Event Enable */ +#define WBCIR_REG_WCEIR_CNTL 0x06 /* CEIR Receiver Counter Low */ +#define WBCIR_REG_WCEIR_CNTH 0x07 /* CEIR Receiver Counter High */ +#define WBCIR_REG_WCEIR_INDEX 0x08 /* CEIR Receiver Index */ +#define WBCIR_REG_WCEIR_DATA 0x09 /* CEIR Receiver Data */ +#define WBCIR_REG_WCEIR_CSL 0x0A /* CEIR Re. Compare Strlen */ +#define WBCIR_REG_WCEIR_CFG1 0x0B /* CEIR Re. Configuration 1 */ +#define WBCIR_REG_WCEIR_CFG2 0x0C /* CEIR Re. Configuration 2 */ + +/* CEIR Enhanced Functionality Registers, relative to data->ebase */ +#define WBCIR_REG_ECEIR_CTS 0x00 /* Enhanced IR Control Status */ +#define WBCIR_REG_ECEIR_CCTL 0x01 /* Infrared Counter Control */ +#define WBCIR_REG_ECEIR_CNT_LO 0x02 /* Infrared Counter LSB */ +#define WBCIR_REG_ECEIR_CNT_HI 0x03 /* Infrared Counter MSB */ +#define WBCIR_REG_ECEIR_IREM 0x04 /* Infrared Emitter Status */ + +/* SP3 Banked Registers, relative to data->sbase */ +#define WBCIR_REG_SP3_BSR 0x03 /* Bank Select, all banks */ + /* Bank 0 */ +#define WBCIR_REG_SP3_RXDATA 0x00 /* FIFO RX data (r) */ +#define WBCIR_REG_SP3_TXDATA 0x00 /* FIFO TX data (w) */ +#define WBCIR_REG_SP3_IER 0x01 /* Interrupt Enable */ +#define WBCIR_REG_SP3_EIR 0x02 /* Event Identification (r) */ +#define WBCIR_REG_SP3_FCR 0x02 /* FIFO Control (w) */ +#define WBCIR_REG_SP3_MCR 0x04 /* Mode Control */ +#define WBCIR_REG_SP3_LSR 0x05 /* Link Status */ +#define WBCIR_REG_SP3_MSR 0x06 /* Modem Status */ +#define WBCIR_REG_SP3_ASCR 0x07 /* Aux Status and Control */ + /* Bank 2 */ +#define WBCIR_REG_SP3_BGDL 0x00 /* Baud Divisor LSB */ +#define WBCIR_REG_SP3_BGDH 0x01 /* Baud Divisor MSB */ +#define WBCIR_REG_SP3_EXCR1 0x02 /* Extended Control 1 */ +#define WBCIR_REG_SP3_EXCR2 0x04 /* Extended Control 2 */ +#define WBCIR_REG_SP3_TXFLV 0x06 /* TX FIFO Level */ +#define WBCIR_REG_SP3_RXFLV 0x07 /* RX FIFO Level */ + /* Bank 3 */ +#define WBCIR_REG_SP3_MRID 0x00 /* Module Identification */ +#define WBCIR_REG_SP3_SH_LCR 0x01 /* LCR Shadow */ +#define WBCIR_REG_SP3_SH_FCR 0x02 /* FCR Shadow */ + /* Bank 4 */ +#define WBCIR_REG_SP3_IRCR1 0x02 /* Infrared Control 1 */ + /* Bank 5 */ +#define WBCIR_REG_SP3_IRCR2 0x04 /* Infrared Control 2 */ + /* Bank 6 */ +#define WBCIR_REG_SP3_IRCR3 0x00 /* Infrared Control 3 */ +#define WBCIR_REG_SP3_SIR_PW 0x02 /* SIR Pulse Width */ + /* Bank 7 */ +#define WBCIR_REG_SP3_IRRXDC 0x00 /* IR RX Demod Control */ +#define WBCIR_REG_SP3_IRTXMC 0x01 /* IR TX Mod Control */ +#define WBCIR_REG_SP3_RCCFG 0x02 /* CEIR Config */ +#define WBCIR_REG_SP3_IRCFG1 0x04 /* Infrared Config 1 */ +#define WBCIR_REG_SP3_IRCFG4 0x07 /* Infrared Config 4 */ + +/* + * Magic values follow + */ + +/* No interrupts for WBCIR_REG_SP3_IER and WBCIR_REG_SP3_EIR */ +#define WBCIR_IRQ_NONE 0x00 +/* RX data bit for WBCIR_REG_SP3_IER and WBCIR_REG_SP3_EIR */ +#define WBCIR_IRQ_RX 0x01 +/* TX data low bit for WBCIR_REG_SP3_IER and WBCIR_REG_SP3_EIR */ +#define WBCIR_IRQ_TX_LOW 0x02 +/* Over/Under-flow bit for WBCIR_REG_SP3_IER and WBCIR_REG_SP3_EIR */ +#define WBCIR_IRQ_ERR 0x04 +/* TX data empty bit for WBCEIR_REG_SP3_IER and WBCIR_REG_SP3_EIR */ +#define WBCIR_IRQ_TX_EMPTY 0x20 +/* Led enable/disable bit for WBCIR_REG_ECEIR_CTS */ +#define WBCIR_LED_ENABLE 0x80 +/* RX data available bit for WBCIR_REG_SP3_LSR */ +#define WBCIR_RX_AVAIL 0x01 +/* RX data overrun error bit for WBCIR_REG_SP3_LSR */ +#define WBCIR_RX_OVERRUN 0x02 +/* TX End-Of-Transmission bit for WBCIR_REG_SP3_ASCR */ +#define WBCIR_TX_EOT 0x04 +/* RX disable bit for WBCIR_REG_SP3_ASCR */ +#define WBCIR_RX_DISABLE 0x20 +/* TX data underrun error bit for WBCIR_REG_SP3_ASCR */ +#define WBCIR_TX_UNDERRUN 0x40 +/* Extended mode enable bit for WBCIR_REG_SP3_EXCR1 */ +#define WBCIR_EXT_ENABLE 0x01 +/* Select compare register in WBCIR_REG_WCEIR_INDEX (bits 5 & 6) */ +#define WBCIR_REGSEL_COMPARE 0x10 +/* Select mask register in WBCIR_REG_WCEIR_INDEX (bits 5 & 6) */ +#define WBCIR_REGSEL_MASK 0x20 +/* Starting address of selected register in WBCIR_REG_WCEIR_INDEX */ +#define WBCIR_REG_ADDR0 0x00 +/* Enable carrier counter */ +#define WBCIR_CNTR_EN 0x01 +/* Reset carrier counter */ +#define WBCIR_CNTR_R 0x02 +/* Invert TX */ +#define WBCIR_IRTX_INV 0x04 +/* Receiver oversampling */ +#define WBCIR_RX_T_OV 0x40 + +/* Valid banks for the SP3 UART */ +enum wbcir_bank { + WBCIR_BANK_0 = 0x00, + WBCIR_BANK_1 = 0x80, + WBCIR_BANK_2 = 0xE0, + WBCIR_BANK_3 = 0xE4, + WBCIR_BANK_4 = 0xE8, + WBCIR_BANK_5 = 0xEC, + WBCIR_BANK_6 = 0xF0, + WBCIR_BANK_7 = 0xF4, +}; + +/* Supported power-on IR Protocols */ +enum wbcir_protocol { + IR_PROTOCOL_RC5 = 0x0, + IR_PROTOCOL_NEC = 0x1, + IR_PROTOCOL_RC6 = 0x2, +}; + +/* Possible states for IR reception */ +enum wbcir_rxstate { + WBCIR_RXSTATE_INACTIVE = 0, + WBCIR_RXSTATE_ACTIVE, + WBCIR_RXSTATE_ERROR +}; + +/* Possible states for IR transmission */ +enum wbcir_txstate { + WBCIR_TXSTATE_INACTIVE = 0, + WBCIR_TXSTATE_ACTIVE, + WBCIR_TXSTATE_ERROR +}; + +/* Misc */ +#define WBCIR_NAME "Winbond CIR" +#define WBCIR_ID_FAMILY 0xF1 /* Family ID for the WPCD376I */ +#define WBCIR_ID_CHIP 0x04 /* Chip ID for the WPCD376I */ +#define WAKEUP_IOMEM_LEN 0x10 /* Wake-Up I/O Reg Len */ +#define EHFUNC_IOMEM_LEN 0x10 /* Enhanced Func I/O Reg Len */ +#define SP_IOMEM_LEN 0x08 /* Serial Port 3 (IR) Reg Len */ + +/* Per-device data */ +struct wbcir_data { + spinlock_t spinlock; + struct rc_dev *dev; + struct led_classdev led; + + unsigned long wbase; /* Wake-Up Baseaddr */ + unsigned long ebase; /* Enhanced Func. Baseaddr */ + unsigned long sbase; /* Serial Port Baseaddr */ + unsigned int irq; /* Serial Port IRQ */ + u8 irqmask; + + /* RX state */ + enum wbcir_rxstate rxstate; + int carrier_report_enabled; + u32 pulse_duration; + + /* TX state */ + enum wbcir_txstate txstate; + u32 txlen; + u32 txoff; + u32 *txbuf; + u8 txmask; + u32 txcarrier; +}; + +static bool invert; /* default = 0 */ +module_param(invert, bool, 0444); +MODULE_PARM_DESC(invert, "Invert the signal from the IR receiver"); + +static bool txandrx; /* default = 0 */ +module_param(txandrx, bool, 0444); +MODULE_PARM_DESC(txandrx, "Allow simultaneous TX and RX"); + + +/***************************************************************************** + * + * UTILITY FUNCTIONS + * + *****************************************************************************/ + +/* Caller needs to hold wbcir_lock */ +static void +wbcir_set_bits(unsigned long addr, u8 bits, u8 mask) +{ + u8 val; + + val = inb(addr); + val = ((val & ~mask) | (bits & mask)); + outb(val, addr); +} + +/* Selects the register bank for the serial port */ +static inline void +wbcir_select_bank(struct wbcir_data *data, enum wbcir_bank bank) +{ + outb(bank, data->sbase + WBCIR_REG_SP3_BSR); +} + +static inline void +wbcir_set_irqmask(struct wbcir_data *data, u8 irqmask) +{ + if (data->irqmask == irqmask) + return; + + wbcir_select_bank(data, WBCIR_BANK_0); + outb(irqmask, data->sbase + WBCIR_REG_SP3_IER); + data->irqmask = irqmask; +} + +static enum led_brightness +wbcir_led_brightness_get(struct led_classdev *led_cdev) +{ + struct wbcir_data *data = container_of(led_cdev, + struct wbcir_data, + led); + + if (inb(data->ebase + WBCIR_REG_ECEIR_CTS) & WBCIR_LED_ENABLE) + return LED_FULL; + else + return LED_OFF; +} + +static void +wbcir_led_brightness_set(struct led_classdev *led_cdev, + enum led_brightness brightness) +{ + struct wbcir_data *data = container_of(led_cdev, + struct wbcir_data, + led); + + wbcir_set_bits(data->ebase + WBCIR_REG_ECEIR_CTS, + brightness == LED_OFF ? 0x00 : WBCIR_LED_ENABLE, + WBCIR_LED_ENABLE); +} + +/* Manchester encodes bits to RC6 message cells (see wbcir_shutdown) */ +static u8 +wbcir_to_rc6cells(u8 val) +{ + u8 coded = 0x00; + int i; + + val &= 0x0F; + for (i = 0; i < 4; i++) { + if (val & 0x01) + coded |= 0x02 << (i * 2); + else + coded |= 0x01 << (i * 2); + val >>= 1; + } + + return coded; +} + +/***************************************************************************** + * + * INTERRUPT FUNCTIONS + * + *****************************************************************************/ + +static void +wbcir_carrier_report(struct wbcir_data *data) +{ + unsigned counter = inb(data->ebase + WBCIR_REG_ECEIR_CNT_LO) | + inb(data->ebase + WBCIR_REG_ECEIR_CNT_HI) << 8; + + if (counter > 0 && counter < 0xffff) { + struct ir_raw_event ev = { + .carrier_report = 1, + .carrier = DIV_ROUND_CLOSEST(counter * 1000000u, + data->pulse_duration) + }; + + ir_raw_event_store(data->dev, &ev); + } + + /* reset and restart the counter */ + data->pulse_duration = 0; + wbcir_set_bits(data->ebase + WBCIR_REG_ECEIR_CCTL, WBCIR_CNTR_R, + WBCIR_CNTR_EN | WBCIR_CNTR_R); + wbcir_set_bits(data->ebase + WBCIR_REG_ECEIR_CCTL, WBCIR_CNTR_EN, + WBCIR_CNTR_EN | WBCIR_CNTR_R); +} + +static void +wbcir_idle_rx(struct rc_dev *dev, bool idle) +{ + struct wbcir_data *data = dev->priv; + + if (!idle && data->rxstate == WBCIR_RXSTATE_INACTIVE) + data->rxstate = WBCIR_RXSTATE_ACTIVE; + + if (idle && data->rxstate != WBCIR_RXSTATE_INACTIVE) { + data->rxstate = WBCIR_RXSTATE_INACTIVE; + + if (data->carrier_report_enabled) + wbcir_carrier_report(data); + + /* Tell hardware to go idle by setting RXINACTIVE */ + outb(WBCIR_RX_DISABLE, data->sbase + WBCIR_REG_SP3_ASCR); + } +} + +static void +wbcir_irq_rx(struct wbcir_data *data, struct pnp_dev *device) +{ + u8 irdata; + struct ir_raw_event rawir = {}; + + /* Since RXHDLEV is set, at least 8 bytes are in the FIFO */ + while (inb(data->sbase + WBCIR_REG_SP3_LSR) & WBCIR_RX_AVAIL) { + irdata = inb(data->sbase + WBCIR_REG_SP3_RXDATA); + if (data->rxstate == WBCIR_RXSTATE_ERROR) + continue; + + rawir.duration = ((irdata & 0x7F) + 1) * + (data->carrier_report_enabled ? 2 : 10); + rawir.pulse = irdata & 0x80 ? false : true; + + if (rawir.pulse) + data->pulse_duration += rawir.duration; + + ir_raw_event_store_with_filter(data->dev, &rawir); + } + + ir_raw_event_handle(data->dev); +} + +static void +wbcir_irq_tx(struct wbcir_data *data) +{ + unsigned int space; + unsigned int used; + u8 bytes[16]; + u8 byte; + + if (!data->txbuf) + return; + + switch (data->txstate) { + case WBCIR_TXSTATE_INACTIVE: + /* TX FIFO empty */ + space = 16; + break; + case WBCIR_TXSTATE_ACTIVE: + /* TX FIFO low (3 bytes or less) */ + space = 13; + break; + case WBCIR_TXSTATE_ERROR: + space = 0; + break; + default: + return; + } + + /* + * TX data is run-length coded in bytes: YXXXXXXX + * Y = space (1) or pulse (0) + * X = duration, encoded as (X + 1) * 10us (i.e 10 to 1280 us) + */ + for (used = 0; used < space && data->txoff != data->txlen; used++) { + if (data->txbuf[data->txoff] == 0) { + data->txoff++; + continue; + } + byte = min((u32)0x80, data->txbuf[data->txoff]); + data->txbuf[data->txoff] -= byte; + byte--; + byte |= (data->txoff % 2 ? 0x80 : 0x00); /* pulse/space */ + bytes[used] = byte; + } + + while (data->txoff != data->txlen && data->txbuf[data->txoff] == 0) + data->txoff++; + + if (used == 0) { + /* Finished */ + if (data->txstate == WBCIR_TXSTATE_ERROR) + /* Clear TX underrun bit */ + outb(WBCIR_TX_UNDERRUN, data->sbase + WBCIR_REG_SP3_ASCR); + wbcir_set_irqmask(data, WBCIR_IRQ_RX | WBCIR_IRQ_ERR); + kfree(data->txbuf); + data->txbuf = NULL; + data->txstate = WBCIR_TXSTATE_INACTIVE; + } else if (data->txoff == data->txlen) { + /* At the end of transmission, tell the hw before last byte */ + outsb(data->sbase + WBCIR_REG_SP3_TXDATA, bytes, used - 1); + outb(WBCIR_TX_EOT, data->sbase + WBCIR_REG_SP3_ASCR); + outb(bytes[used - 1], data->sbase + WBCIR_REG_SP3_TXDATA); + wbcir_set_irqmask(data, WBCIR_IRQ_RX | WBCIR_IRQ_ERR | + WBCIR_IRQ_TX_EMPTY); + } else { + /* More data to follow... */ + outsb(data->sbase + WBCIR_REG_SP3_RXDATA, bytes, used); + if (data->txstate == WBCIR_TXSTATE_INACTIVE) { + wbcir_set_irqmask(data, WBCIR_IRQ_RX | WBCIR_IRQ_ERR | + WBCIR_IRQ_TX_LOW); + data->txstate = WBCIR_TXSTATE_ACTIVE; + } + } +} + +static irqreturn_t +wbcir_irq_handler(int irqno, void *cookie) +{ + struct pnp_dev *device = cookie; + struct wbcir_data *data = pnp_get_drvdata(device); + unsigned long flags; + u8 status; + + spin_lock_irqsave(&data->spinlock, flags); + wbcir_select_bank(data, WBCIR_BANK_0); + status = inb(data->sbase + WBCIR_REG_SP3_EIR); + status &= data->irqmask; + + if (!status) { + spin_unlock_irqrestore(&data->spinlock, flags); + return IRQ_NONE; + } + + if (status & WBCIR_IRQ_ERR) { + /* RX overflow? (read clears bit) */ + if (inb(data->sbase + WBCIR_REG_SP3_LSR) & WBCIR_RX_OVERRUN) { + data->rxstate = WBCIR_RXSTATE_ERROR; + ir_raw_event_reset(data->dev); + } + + /* TX underflow? */ + if (inb(data->sbase + WBCIR_REG_SP3_ASCR) & WBCIR_TX_UNDERRUN) + data->txstate = WBCIR_TXSTATE_ERROR; + } + + if (status & WBCIR_IRQ_RX) + wbcir_irq_rx(data, device); + + if (status & (WBCIR_IRQ_TX_LOW | WBCIR_IRQ_TX_EMPTY)) + wbcir_irq_tx(data); + + spin_unlock_irqrestore(&data->spinlock, flags); + return IRQ_HANDLED; +} + +/***************************************************************************** + * + * RC-CORE INTERFACE FUNCTIONS + * + *****************************************************************************/ + +static int +wbcir_set_carrier_report(struct rc_dev *dev, int enable) +{ + struct wbcir_data *data = dev->priv; + unsigned long flags; + + spin_lock_irqsave(&data->spinlock, flags); + + if (data->carrier_report_enabled == enable) { + spin_unlock_irqrestore(&data->spinlock, flags); + return 0; + } + + data->pulse_duration = 0; + wbcir_set_bits(data->ebase + WBCIR_REG_ECEIR_CCTL, WBCIR_CNTR_R, + WBCIR_CNTR_EN | WBCIR_CNTR_R); + + if (enable && data->dev->idle) + wbcir_set_bits(data->ebase + WBCIR_REG_ECEIR_CCTL, + WBCIR_CNTR_EN, WBCIR_CNTR_EN | WBCIR_CNTR_R); + + /* Set a higher sampling resolution if carrier reports are enabled */ + wbcir_select_bank(data, WBCIR_BANK_2); + data->dev->rx_resolution = enable ? 2 : 10; + outb(enable ? 0x03 : 0x0f, data->sbase + WBCIR_REG_SP3_BGDL); + outb(0x00, data->sbase + WBCIR_REG_SP3_BGDH); + + /* Enable oversampling if carrier reports are enabled */ + wbcir_select_bank(data, WBCIR_BANK_7); + wbcir_set_bits(data->sbase + WBCIR_REG_SP3_RCCFG, + enable ? WBCIR_RX_T_OV : 0, WBCIR_RX_T_OV); + + data->carrier_report_enabled = enable; + spin_unlock_irqrestore(&data->spinlock, flags); + + return 0; +} + +static int +wbcir_txcarrier(struct rc_dev *dev, u32 carrier) +{ + struct wbcir_data *data = dev->priv; + unsigned long flags; + u8 val; + u32 freq; + + freq = DIV_ROUND_CLOSEST(carrier, 1000); + if (freq < 30 || freq > 60) + return -EINVAL; + + switch (freq) { + case 58: + case 59: + case 60: + val = freq - 58; + freq *= 1000; + break; + case 57: + val = freq - 27; + freq = 56900; + break; + default: + val = freq - 27; + freq *= 1000; + break; + } + + spin_lock_irqsave(&data->spinlock, flags); + if (data->txstate != WBCIR_TXSTATE_INACTIVE) { + spin_unlock_irqrestore(&data->spinlock, flags); + return -EBUSY; + } + + if (data->txcarrier != freq) { + wbcir_select_bank(data, WBCIR_BANK_7); + wbcir_set_bits(data->sbase + WBCIR_REG_SP3_IRTXMC, val, 0x1F); + data->txcarrier = freq; + } + + spin_unlock_irqrestore(&data->spinlock, flags); + return 0; +} + +static int +wbcir_txmask(struct rc_dev *dev, u32 mask) +{ + struct wbcir_data *data = dev->priv; + unsigned long flags; + u8 val; + + /* return the number of transmitters */ + if (mask > 15) + return 4; + + /* Four outputs, only one output can be enabled at a time */ + switch (mask) { + case 0x1: + val = 0x0; + break; + case 0x2: + val = 0x1; + break; + case 0x4: + val = 0x2; + break; + case 0x8: + val = 0x3; + break; + default: + return -EINVAL; + } + + spin_lock_irqsave(&data->spinlock, flags); + if (data->txstate != WBCIR_TXSTATE_INACTIVE) { + spin_unlock_irqrestore(&data->spinlock, flags); + return -EBUSY; + } + + if (data->txmask != mask) { + wbcir_set_bits(data->ebase + WBCIR_REG_ECEIR_CTS, val, 0x0c); + data->txmask = mask; + } + + spin_unlock_irqrestore(&data->spinlock, flags); + return 0; +} + +static int +wbcir_tx(struct rc_dev *dev, unsigned *b, unsigned count) +{ + struct wbcir_data *data = dev->priv; + unsigned *buf; + unsigned i; + unsigned long flags; + + buf = kmalloc_array(count, sizeof(*b), GFP_KERNEL); + if (!buf) + return -ENOMEM; + + /* Convert values to multiples of 10us */ + for (i = 0; i < count; i++) + buf[i] = DIV_ROUND_CLOSEST(b[i], 10); + + /* Not sure if this is possible, but better safe than sorry */ + spin_lock_irqsave(&data->spinlock, flags); + if (data->txstate != WBCIR_TXSTATE_INACTIVE) { + spin_unlock_irqrestore(&data->spinlock, flags); + kfree(buf); + return -EBUSY; + } + + /* Fill the TX fifo once, the irq handler will do the rest */ + data->txbuf = buf; + data->txlen = count; + data->txoff = 0; + wbcir_irq_tx(data); + + /* We're done */ + spin_unlock_irqrestore(&data->spinlock, flags); + return count; +} + +/***************************************************************************** + * + * SETUP/INIT/SUSPEND/RESUME FUNCTIONS + * + *****************************************************************************/ + +static void +wbcir_shutdown(struct pnp_dev *device) +{ + struct device *dev = &device->dev; + struct wbcir_data *data = pnp_get_drvdata(device); + struct rc_dev *rc = data->dev; + bool do_wake = true; + u8 match[11]; + u8 mask[11]; + u8 rc6_csl = 0; + u8 proto; + u32 wake_sc = rc->scancode_wakeup_filter.data; + u32 mask_sc = rc->scancode_wakeup_filter.mask; + int i; + + memset(match, 0, sizeof(match)); + memset(mask, 0, sizeof(mask)); + + if (!mask_sc || !device_may_wakeup(dev)) { + do_wake = false; + goto finish; + } + + switch (rc->wakeup_protocol) { + case RC_PROTO_RC5: + /* Mask = 13 bits, ex toggle */ + mask[0] = (mask_sc & 0x003f); + mask[0] |= (mask_sc & 0x0300) >> 2; + mask[1] = (mask_sc & 0x1c00) >> 10; + if (mask_sc & 0x0040) /* 2nd start bit */ + match[1] |= 0x10; + + match[0] = (wake_sc & 0x003F); /* 6 command bits */ + match[0] |= (wake_sc & 0x0300) >> 2; /* 2 address bits */ + match[1] = (wake_sc & 0x1c00) >> 10; /* 3 address bits */ + if (!(wake_sc & 0x0040)) /* 2nd start bit */ + match[1] |= 0x10; + + proto = IR_PROTOCOL_RC5; + break; + + case RC_PROTO_NEC: + mask[1] = bitrev8(mask_sc); + mask[0] = mask[1]; + mask[3] = bitrev8(mask_sc >> 8); + mask[2] = mask[3]; + + match[1] = bitrev8(wake_sc); + match[0] = ~match[1]; + match[3] = bitrev8(wake_sc >> 8); + match[2] = ~match[3]; + + proto = IR_PROTOCOL_NEC; + break; + + case RC_PROTO_NECX: + mask[1] = bitrev8(mask_sc); + mask[0] = mask[1]; + mask[2] = bitrev8(mask_sc >> 8); + mask[3] = bitrev8(mask_sc >> 16); + + match[1] = bitrev8(wake_sc); + match[0] = ~match[1]; + match[2] = bitrev8(wake_sc >> 8); + match[3] = bitrev8(wake_sc >> 16); + + proto = IR_PROTOCOL_NEC; + break; + + case RC_PROTO_NEC32: + mask[0] = bitrev8(mask_sc); + mask[1] = bitrev8(mask_sc >> 8); + mask[2] = bitrev8(mask_sc >> 16); + mask[3] = bitrev8(mask_sc >> 24); + + match[0] = bitrev8(wake_sc); + match[1] = bitrev8(wake_sc >> 8); + match[2] = bitrev8(wake_sc >> 16); + match[3] = bitrev8(wake_sc >> 24); + + proto = IR_PROTOCOL_NEC; + break; + + case RC_PROTO_RC6_0: + /* Command */ + match[0] = wbcir_to_rc6cells(wake_sc >> 0); + mask[0] = wbcir_to_rc6cells(mask_sc >> 0); + match[1] = wbcir_to_rc6cells(wake_sc >> 4); + mask[1] = wbcir_to_rc6cells(mask_sc >> 4); + + /* Address */ + match[2] = wbcir_to_rc6cells(wake_sc >> 8); + mask[2] = wbcir_to_rc6cells(mask_sc >> 8); + match[3] = wbcir_to_rc6cells(wake_sc >> 12); + mask[3] = wbcir_to_rc6cells(mask_sc >> 12); + + /* Header */ + match[4] = 0x50; /* mode1 = mode0 = 0, ignore toggle */ + mask[4] = 0xF0; + match[5] = 0x09; /* start bit = 1, mode2 = 0 */ + mask[5] = 0x0F; + + rc6_csl = 44; + proto = IR_PROTOCOL_RC6; + break; + + case RC_PROTO_RC6_6A_24: + case RC_PROTO_RC6_6A_32: + case RC_PROTO_RC6_MCE: + i = 0; + + /* Command */ + match[i] = wbcir_to_rc6cells(wake_sc >> 0); + mask[i++] = wbcir_to_rc6cells(mask_sc >> 0); + match[i] = wbcir_to_rc6cells(wake_sc >> 4); + mask[i++] = wbcir_to_rc6cells(mask_sc >> 4); + + /* Address + Toggle */ + match[i] = wbcir_to_rc6cells(wake_sc >> 8); + mask[i++] = wbcir_to_rc6cells(mask_sc >> 8); + match[i] = wbcir_to_rc6cells(wake_sc >> 12); + mask[i++] = wbcir_to_rc6cells(mask_sc >> 12); + + /* Customer bits 7 - 0 */ + match[i] = wbcir_to_rc6cells(wake_sc >> 16); + mask[i++] = wbcir_to_rc6cells(mask_sc >> 16); + + if (rc->wakeup_protocol == RC_PROTO_RC6_6A_20) { + rc6_csl = 52; + } else { + match[i] = wbcir_to_rc6cells(wake_sc >> 20); + mask[i++] = wbcir_to_rc6cells(mask_sc >> 20); + + if (rc->wakeup_protocol == RC_PROTO_RC6_6A_24) { + rc6_csl = 60; + } else { + /* Customer range bit and bits 15 - 8 */ + match[i] = wbcir_to_rc6cells(wake_sc >> 24); + mask[i++] = wbcir_to_rc6cells(mask_sc >> 24); + match[i] = wbcir_to_rc6cells(wake_sc >> 28); + mask[i++] = wbcir_to_rc6cells(mask_sc >> 28); + rc6_csl = 76; + } + } + + /* Header */ + match[i] = 0x93; /* mode1 = mode0 = 1, submode = 0 */ + mask[i++] = 0xFF; + match[i] = 0x0A; /* start bit = 1, mode2 = 1 */ + mask[i++] = 0x0F; + proto = IR_PROTOCOL_RC6; + break; + default: + do_wake = false; + break; + } + +finish: + if (do_wake) { + /* Set compare and compare mask */ + wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_INDEX, + WBCIR_REGSEL_COMPARE | WBCIR_REG_ADDR0, + 0x3F); + outsb(data->wbase + WBCIR_REG_WCEIR_DATA, match, 11); + wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_INDEX, + WBCIR_REGSEL_MASK | WBCIR_REG_ADDR0, + 0x3F); + outsb(data->wbase + WBCIR_REG_WCEIR_DATA, mask, 11); + + /* RC6 Compare String Len */ + outb(rc6_csl, data->wbase + WBCIR_REG_WCEIR_CSL); + + /* Clear status bits NEC_REP, BUFF, MSG_END, MATCH */ + wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_STS, 0x17, 0x17); + + /* Clear BUFF_EN, Clear END_EN, Set MATCH_EN */ + wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_EV_EN, 0x01, 0x07); + + /* Set CEIR_EN */ + wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_CTL, + (proto << 4) | 0x01, 0x31); + + } else { + /* Clear BUFF_EN, Clear END_EN, Clear MATCH_EN */ + wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_EV_EN, 0x00, 0x07); + + /* Clear CEIR_EN */ + wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_CTL, 0x00, 0x01); + } + + /* + * ACPI will set the HW disable bit for SP3 which means that the + * output signals are left in an undefined state which may cause + * spurious interrupts which we need to ignore until the hardware + * is reinitialized. + */ + wbcir_set_irqmask(data, WBCIR_IRQ_NONE); + disable_irq(data->irq); +} + +/* + * Wakeup handling is done on shutdown. + */ +static int +wbcir_set_wakeup_filter(struct rc_dev *rc, struct rc_scancode_filter *filter) +{ + return 0; +} + +static int +wbcir_suspend(struct pnp_dev *device, pm_message_t state) +{ + struct wbcir_data *data = pnp_get_drvdata(device); + led_classdev_suspend(&data->led); + wbcir_shutdown(device); + return 0; +} + +static void +wbcir_init_hw(struct wbcir_data *data) +{ + /* Disable interrupts */ + wbcir_set_irqmask(data, WBCIR_IRQ_NONE); + + /* Set RX_INV, Clear CEIR_EN (needed for the led) */ + wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_CTL, invert ? 8 : 0, 0x09); + + /* Clear status bits NEC_REP, BUFF, MSG_END, MATCH */ + wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_STS, 0x17, 0x17); + + /* Clear BUFF_EN, Clear END_EN, Clear MATCH_EN */ + wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_EV_EN, 0x00, 0x07); + + /* Set RC5 cell time to correspond to 36 kHz */ + wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_CFG1, 0x4A, 0x7F); + + /* Set IRTX_INV */ + if (invert) + outb(WBCIR_IRTX_INV, data->ebase + WBCIR_REG_ECEIR_CCTL); + else + outb(0x00, data->ebase + WBCIR_REG_ECEIR_CCTL); + + /* + * Clear IR LED, set SP3 clock to 24Mhz, set TX mask to IRTX1, + * set SP3_IRRX_SW to binary 01, helpfully not documented + */ + outb(0x10, data->ebase + WBCIR_REG_ECEIR_CTS); + data->txmask = 0x1; + + /* Enable extended mode */ + wbcir_select_bank(data, WBCIR_BANK_2); + outb(WBCIR_EXT_ENABLE, data->sbase + WBCIR_REG_SP3_EXCR1); + + /* + * Configure baud generator, IR data will be sampled at + * a bitrate of: (24Mhz * prescaler) / (divisor * 16). + * + * The ECIR registers include a flag to change the + * 24Mhz clock freq to 48Mhz. + * + * It's not documented in the specs, but fifo levels + * other than 16 seems to be unsupported. + */ + + /* prescaler 1.0, tx/rx fifo lvl 16 */ + outb(0x30, data->sbase + WBCIR_REG_SP3_EXCR2); + + /* Set baud divisor to sample every 10 us */ + outb(0x0f, data->sbase + WBCIR_REG_SP3_BGDL); + outb(0x00, data->sbase + WBCIR_REG_SP3_BGDH); + + /* Set CEIR mode */ + wbcir_select_bank(data, WBCIR_BANK_0); + outb(0xC0, data->sbase + WBCIR_REG_SP3_MCR); + inb(data->sbase + WBCIR_REG_SP3_LSR); /* Clear LSR */ + inb(data->sbase + WBCIR_REG_SP3_MSR); /* Clear MSR */ + + /* Disable RX demod, enable run-length enc/dec, set freq span */ + wbcir_select_bank(data, WBCIR_BANK_7); + outb(0x90, data->sbase + WBCIR_REG_SP3_RCCFG); + + /* Disable timer */ + wbcir_select_bank(data, WBCIR_BANK_4); + outb(0x00, data->sbase + WBCIR_REG_SP3_IRCR1); + + /* Disable MSR interrupt, clear AUX_IRX, mask RX during TX? */ + wbcir_select_bank(data, WBCIR_BANK_5); + outb(txandrx ? 0x03 : 0x02, data->sbase + WBCIR_REG_SP3_IRCR2); + + /* Disable CRC */ + wbcir_select_bank(data, WBCIR_BANK_6); + outb(0x20, data->sbase + WBCIR_REG_SP3_IRCR3); + + /* Set RX demodulation freq, not really used */ + wbcir_select_bank(data, WBCIR_BANK_7); + outb(0xF2, data->sbase + WBCIR_REG_SP3_IRRXDC); + + /* Set TX modulation, 36kHz, 7us pulse width */ + outb(0x69, data->sbase + WBCIR_REG_SP3_IRTXMC); + data->txcarrier = 36000; + + /* Set invert and pin direction */ + if (invert) + outb(0x10, data->sbase + WBCIR_REG_SP3_IRCFG4); + else + outb(0x00, data->sbase + WBCIR_REG_SP3_IRCFG4); + + /* Set FIFO thresholds (RX = 8, TX = 3), reset RX/TX */ + wbcir_select_bank(data, WBCIR_BANK_0); + outb(0x97, data->sbase + WBCIR_REG_SP3_FCR); + + /* Clear AUX status bits */ + outb(0xE0, data->sbase + WBCIR_REG_SP3_ASCR); + + /* Clear RX state */ + data->rxstate = WBCIR_RXSTATE_INACTIVE; + wbcir_idle_rx(data->dev, true); + + /* Clear TX state */ + if (data->txstate == WBCIR_TXSTATE_ACTIVE) { + kfree(data->txbuf); + data->txbuf = NULL; + data->txstate = WBCIR_TXSTATE_INACTIVE; + } + + /* Enable interrupts */ + wbcir_set_irqmask(data, WBCIR_IRQ_RX | WBCIR_IRQ_ERR); +} + +static int +wbcir_resume(struct pnp_dev *device) +{ + struct wbcir_data *data = pnp_get_drvdata(device); + + wbcir_init_hw(data); + ir_raw_event_reset(data->dev); + enable_irq(data->irq); + led_classdev_resume(&data->led); + + return 0; +} + +static int +wbcir_probe(struct pnp_dev *device, const struct pnp_device_id *dev_id) +{ + struct device *dev = &device->dev; + struct wbcir_data *data; + int err; + + if (!(pnp_port_len(device, 0) == EHFUNC_IOMEM_LEN && + pnp_port_len(device, 1) == WAKEUP_IOMEM_LEN && + pnp_port_len(device, 2) == SP_IOMEM_LEN)) { + dev_err(dev, "Invalid resources\n"); + return -ENODEV; + } + + data = kzalloc(sizeof(*data), GFP_KERNEL); + if (!data) { + err = -ENOMEM; + goto exit; + } + + pnp_set_drvdata(device, data); + + spin_lock_init(&data->spinlock); + data->ebase = pnp_port_start(device, 0); + data->wbase = pnp_port_start(device, 1); + data->sbase = pnp_port_start(device, 2); + data->irq = pnp_irq(device, 0); + + if (data->wbase == 0 || data->ebase == 0 || + data->sbase == 0 || data->irq == -1) { + err = -ENODEV; + dev_err(dev, "Invalid resources\n"); + goto exit_free_data; + } + + dev_dbg(&device->dev, "Found device (w: 0x%lX, e: 0x%lX, s: 0x%lX, i: %u)\n", + data->wbase, data->ebase, data->sbase, data->irq); + + data->led.name = "cir::activity"; + data->led.default_trigger = "rc-feedback"; + data->led.brightness_set = wbcir_led_brightness_set; + data->led.brightness_get = wbcir_led_brightness_get; + err = led_classdev_register(&device->dev, &data->led); + if (err) + goto exit_free_data; + + data->dev = rc_allocate_device(RC_DRIVER_IR_RAW); + if (!data->dev) { + err = -ENOMEM; + goto exit_unregister_led; + } + + data->dev->driver_name = DRVNAME; + data->dev->device_name = WBCIR_NAME; + data->dev->input_phys = "wbcir/cir0"; + data->dev->input_id.bustype = BUS_HOST; + data->dev->input_id.vendor = PCI_VENDOR_ID_WINBOND; + data->dev->input_id.product = WBCIR_ID_FAMILY; + data->dev->input_id.version = WBCIR_ID_CHIP; + data->dev->map_name = RC_MAP_RC6_MCE; + data->dev->s_idle = wbcir_idle_rx; + data->dev->s_carrier_report = wbcir_set_carrier_report; + data->dev->s_tx_mask = wbcir_txmask; + data->dev->s_tx_carrier = wbcir_txcarrier; + data->dev->tx_ir = wbcir_tx; + data->dev->priv = data; + data->dev->dev.parent = &device->dev; + data->dev->min_timeout = 1; + data->dev->timeout = IR_DEFAULT_TIMEOUT; + data->dev->max_timeout = 10 * IR_DEFAULT_TIMEOUT; + data->dev->rx_resolution = 2; + data->dev->allowed_protocols = RC_PROTO_BIT_ALL_IR_DECODER; + data->dev->allowed_wakeup_protocols = RC_PROTO_BIT_NEC | + RC_PROTO_BIT_NECX | RC_PROTO_BIT_NEC32 | RC_PROTO_BIT_RC5 | + RC_PROTO_BIT_RC6_0 | RC_PROTO_BIT_RC6_6A_20 | + RC_PROTO_BIT_RC6_6A_24 | RC_PROTO_BIT_RC6_6A_32 | + RC_PROTO_BIT_RC6_MCE; + data->dev->wakeup_protocol = RC_PROTO_RC6_MCE; + data->dev->scancode_wakeup_filter.data = 0x800f040c; + data->dev->scancode_wakeup_filter.mask = 0xffff7fff; + data->dev->s_wakeup_filter = wbcir_set_wakeup_filter; + + err = rc_register_device(data->dev); + if (err) + goto exit_free_rc; + + if (!request_region(data->wbase, WAKEUP_IOMEM_LEN, DRVNAME)) { + dev_err(dev, "Region 0x%lx-0x%lx already in use!\n", + data->wbase, data->wbase + WAKEUP_IOMEM_LEN - 1); + err = -EBUSY; + goto exit_unregister_device; + } + + if (!request_region(data->ebase, EHFUNC_IOMEM_LEN, DRVNAME)) { + dev_err(dev, "Region 0x%lx-0x%lx already in use!\n", + data->ebase, data->ebase + EHFUNC_IOMEM_LEN - 1); + err = -EBUSY; + goto exit_release_wbase; + } + + if (!request_region(data->sbase, SP_IOMEM_LEN, DRVNAME)) { + dev_err(dev, "Region 0x%lx-0x%lx already in use!\n", + data->sbase, data->sbase + SP_IOMEM_LEN - 1); + err = -EBUSY; + goto exit_release_ebase; + } + + err = request_irq(data->irq, wbcir_irq_handler, + 0, DRVNAME, device); + if (err) { + dev_err(dev, "Failed to claim IRQ %u\n", data->irq); + err = -EBUSY; + goto exit_release_sbase; + } + + device_init_wakeup(&device->dev, 1); + + wbcir_init_hw(data); + + return 0; + +exit_release_sbase: + release_region(data->sbase, SP_IOMEM_LEN); +exit_release_ebase: + release_region(data->ebase, EHFUNC_IOMEM_LEN); +exit_release_wbase: + release_region(data->wbase, WAKEUP_IOMEM_LEN); +exit_unregister_device: + rc_unregister_device(data->dev); + data->dev = NULL; +exit_free_rc: + rc_free_device(data->dev); +exit_unregister_led: + led_classdev_unregister(&data->led); +exit_free_data: + kfree(data); + pnp_set_drvdata(device, NULL); +exit: + return err; +} + +static void +wbcir_remove(struct pnp_dev *device) +{ + struct wbcir_data *data = pnp_get_drvdata(device); + + /* Disable interrupts */ + wbcir_set_irqmask(data, WBCIR_IRQ_NONE); + free_irq(data->irq, device); + + /* Clear status bits NEC_REP, BUFF, MSG_END, MATCH */ + wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_STS, 0x17, 0x17); + + /* Clear CEIR_EN */ + wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_CTL, 0x00, 0x01); + + /* Clear BUFF_EN, END_EN, MATCH_EN */ + wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_EV_EN, 0x00, 0x07); + + rc_unregister_device(data->dev); + + led_classdev_unregister(&data->led); + + /* This is ok since &data->led isn't actually used */ + wbcir_led_brightness_set(&data->led, LED_OFF); + + release_region(data->wbase, WAKEUP_IOMEM_LEN); + release_region(data->ebase, EHFUNC_IOMEM_LEN); + release_region(data->sbase, SP_IOMEM_LEN); + + kfree(data); + + pnp_set_drvdata(device, NULL); +} + +static const struct pnp_device_id wbcir_ids[] = { + { "WEC1022", 0 }, + { "", 0 } +}; +MODULE_DEVICE_TABLE(pnp, wbcir_ids); + +static struct pnp_driver wbcir_driver = { + .name = DRVNAME, + .id_table = wbcir_ids, + .probe = wbcir_probe, + .remove = wbcir_remove, + .suspend = wbcir_suspend, + .resume = wbcir_resume, + .shutdown = wbcir_shutdown +}; + +static int __init +wbcir_init(void) +{ + int ret; + + ret = pnp_register_driver(&wbcir_driver); + if (ret) + pr_err("Unable to register driver\n"); + + return ret; +} + +static void __exit +wbcir_exit(void) +{ + pnp_unregister_driver(&wbcir_driver); +} + +module_init(wbcir_init); +module_exit(wbcir_exit); + +MODULE_AUTHOR("David Härdeman <david@hardeman.nu>"); +MODULE_DESCRIPTION("Winbond SuperI/O Consumer IR Driver"); +MODULE_LICENSE("GPL"); |