diff options
Diffstat (limited to 'drivers/misc/Kconfig')
| -rw-r--r-- | drivers/misc/Kconfig | 484 |
1 files changed, 484 insertions, 0 deletions
diff --git a/drivers/misc/Kconfig b/drivers/misc/Kconfig new file mode 100644 index 000000000..fafa8b0d8 --- /dev/null +++ b/drivers/misc/Kconfig @@ -0,0 +1,484 @@ +# SPDX-License-Identifier: GPL-2.0-only +# +# Misc strange devices +# + +menu "Misc devices" + +config SENSORS_LIS3LV02D + tristate + depends on INPUT + +config AD525X_DPOT + tristate "Analog Devices Digital Potentiometers" + depends on (I2C || SPI) && SYSFS + help + If you say yes here, you get support for the Analog Devices + AD5258, AD5259, AD5251, AD5252, AD5253, AD5254, AD5255 + AD5160, AD5161, AD5162, AD5165, AD5200, AD5201, AD5203, + AD5204, AD5206, AD5207, AD5231, AD5232, AD5233, AD5235, + AD5260, AD5262, AD5263, AD5290, AD5291, AD5292, AD5293, + AD7376, AD8400, AD8402, AD8403, ADN2850, AD5241, AD5242, + AD5243, AD5245, AD5246, AD5247, AD5248, AD5280, AD5282, + ADN2860, AD5273, AD5171, AD5170, AD5172, AD5173, AD5270, + AD5271, AD5272, AD5274 + digital potentiometer chips. + + See Documentation/misc-devices/ad525x_dpot.rst for the + userspace interface. + + This driver can also be built as a module. If so, the module + will be called ad525x_dpot. + +config AD525X_DPOT_I2C + tristate "support I2C bus connection" + depends on AD525X_DPOT && I2C + help + Say Y here if you have a digital potentiometers hooked to an I2C bus. + + To compile this driver as a module, choose M here: the + module will be called ad525x_dpot-i2c. + +config AD525X_DPOT_SPI + tristate "support SPI bus connection" + depends on AD525X_DPOT && SPI_MASTER + help + Say Y here if you have a digital potentiometers hooked to an SPI bus. + + If unsure, say N (but it's safe to say "Y"). + + To compile this driver as a module, choose M here: the + module will be called ad525x_dpot-spi. + +config ATMEL_TCLIB + bool "Atmel AT32/AT91 Timer/Counter Library" + depends on ARCH_AT91 + help + Select this if you want a library to allocate the Timer/Counter + blocks found on many Atmel processors. This facilitates using + these blocks by different drivers despite processor differences. + +config DUMMY_IRQ + tristate "Dummy IRQ handler" + help + This module accepts a single 'irq' parameter, which it should register for. + The sole purpose of this module is to help with debugging of systems on + which spurious IRQs would happen on disabled IRQ vector. + +config IBM_ASM + tristate "Device driver for IBM RSA service processor" + depends on X86 && PCI && INPUT + depends on SERIAL_8250 || SERIAL_8250=n + help + This option enables device driver support for in-band access to the + IBM RSA (Condor) service processor in eServer xSeries systems. + The ibmasm device driver allows user space application to access + ASM (Advanced Systems Management) functions on the service + processor. The driver is meant to be used in conjunction with + a user space API. + The ibmasm driver also enables the OS to use the UART on the + service processor board as a regular serial port. To make use of + this feature serial driver support (CONFIG_SERIAL_8250) must be + enabled. + + WARNING: This software may not be supported or function + correctly on your IBM server. Please consult the IBM ServerProven + website <https://www-03.ibm.com/systems/info/x86servers/serverproven/compat/us/> + for information on the specific driver level and support statement + for your IBM server. + +config IBMVMC + tristate "IBM Virtual Management Channel support" + depends on PPC_PSERIES + help + This is the IBM POWER Virtual Management Channel + + This driver is to be used for the POWER Virtual + Management Channel virtual adapter on the PowerVM + platform. It provides both request/response and + async message support through the /dev/ibmvmc node. + + To compile this driver as a module, choose M here: the + module will be called ibmvmc. + +config PHANTOM + tristate "Sensable PHANToM (PCI)" + depends on PCI + help + Say Y here if you want to build a driver for Sensable PHANToM device. + + This driver is only for PCI PHANToMs. + + If you choose to build module, its name will be phantom. If unsure, + say N here. + +config INTEL_MID_PTI + tristate "Parallel Trace Interface for MIPI P1149.7 cJTAG standard" + depends on PCI && TTY && (X86_INTEL_MID || COMPILE_TEST) + help + The PTI (Parallel Trace Interface) driver directs + trace data routed from various parts in the system out + through an Intel Penwell PTI port and out of the mobile + device for analysis with a debugging tool (Lauterbach or Fido). + + You should select this driver if the target kernel is meant for + an Intel Atom (non-netbook) mobile device containing a MIPI + P1149.7 standard implementation. + +config TIFM_CORE + tristate "TI Flash Media interface support" + depends on PCI + help + If you want support for Texas Instruments(R) Flash Media adapters + you should select this option and then also choose an appropriate + host adapter, such as 'TI Flash Media PCI74xx/PCI76xx host adapter + support', if you have a TI PCI74xx compatible card reader, for + example. + You will also have to select some flash card format drivers. MMC/SD + cards are supported via 'MMC/SD Card support: TI Flash Media MMC/SD + Interface support (MMC_TIFM_SD)'. + + To compile this driver as a module, choose M here: the module will + be called tifm_core. + +config TIFM_7XX1 + tristate "TI Flash Media PCI74xx/PCI76xx host adapter support" + depends on PCI && TIFM_CORE + default TIFM_CORE + help + This option enables support for Texas Instruments(R) PCI74xx and + PCI76xx families of Flash Media adapters, found in many laptops. + To make actual use of the device, you will have to select some + flash card format drivers, as outlined in the TIFM_CORE Help. + + To compile this driver as a module, choose M here: the module will + be called tifm_7xx1. + +config ICS932S401 + tristate "Integrated Circuits ICS932S401" + depends on I2C + help + If you say yes here you get support for the Integrated Circuits + ICS932S401 clock control chips. + + This driver can also be built as a module. If so, the module + will be called ics932s401. + +config ATMEL_SSC + tristate "Device driver for Atmel SSC peripheral" + depends on HAS_IOMEM && (ARCH_AT91 || COMPILE_TEST) + help + This option enables device driver support for Atmel Synchronized + Serial Communication peripheral (SSC). + + The SSC peripheral supports a wide variety of serial frame based + communications, i.e. I2S, SPI, etc. + + If unsure, say N. + +config ENCLOSURE_SERVICES + tristate "Enclosure Services" + help + Provides support for intelligent enclosures (bays which + contain storage devices). You also need either a host + driver (SCSI/ATA) which supports enclosures + or a SCSI enclosure device (SES) to use these services. + +config SGI_XP + tristate "Support communication between SGI SSIs" + depends on NET + depends on (IA64_SGI_UV || X86_UV) && SMP + depends on X86_64 || BROKEN + select SGI_GRU if X86_64 && SMP + help + An SGI machine can be divided into multiple Single System + Images which act independently of each other and have + hardware based memory protection from the others. Enabling + this feature will allow for direct communication between SSIs + based on a network adapter and DMA messaging. + +config CS5535_MFGPT + tristate "CS5535/CS5536 Geode Multi-Function General Purpose Timer (MFGPT) support" + depends on MFD_CS5535 + help + This driver provides access to MFGPT functionality for other + drivers that need timers. MFGPTs are available in the CS5535 and + CS5536 companion chips that are found in AMD Geode and several + other platforms. They have a better resolution and max interval + than the generic PIT, and are suitable for use as high-res timers. + You probably don't want to enable this manually; other drivers that + make use of it should enable it. + +config CS5535_MFGPT_DEFAULT_IRQ + int + depends on CS5535_MFGPT + default 7 + help + MFGPTs on the CS5535 require an interrupt. The selected IRQ + can be overridden as a module option as well as by driver that + use the cs5535_mfgpt_ API; however, different architectures might + want to use a different IRQ by default. This is here for + architectures to set as necessary. + +config CS5535_CLOCK_EVENT_SRC + tristate "CS5535/CS5536 high-res timer (MFGPT) events" + depends on GENERIC_CLOCKEVENTS && CS5535_MFGPT + help + This driver provides a clock event source based on the MFGPT + timer(s) in the CS5535 and CS5536 companion chips. + MFGPTs have a better resolution and max interval than the + generic PIT, and are suitable for use as high-res timers. + +config HP_ILO + tristate "Channel interface driver for the HP iLO processor" + depends on PCI + help + The channel interface driver allows applications to communicate + with iLO management processors present on HP ProLiant servers. + Upon loading, the driver creates /dev/hpilo/dXccbN files, which + can be used to gather data from the management processor, via + read and write system calls. + + To compile this driver as a module, choose M here: the + module will be called hpilo. + +config QCOM_COINCELL + tristate "Qualcomm coincell charger support" + depends on MFD_SPMI_PMIC || COMPILE_TEST + help + This driver supports the coincell block found inside of + Qualcomm PMICs. The coincell charger provides a means to + charge a coincell battery or backup capacitor which is used + to maintain PMIC register and RTC state in the absence of + external power. + +config QCOM_FASTRPC + tristate "Qualcomm FastRPC" + depends on ARCH_QCOM || COMPILE_TEST + depends on RPMSG + select DMA_SHARED_BUFFER + help + Provides a communication mechanism that allows for clients to + make remote method invocations across processor boundary to + applications DSP processor. Say M if you want to enable this + module. + +config SGI_GRU + tristate "SGI GRU driver" + depends on X86_UV && SMP + select MMU_NOTIFIER + help + The GRU is a hardware resource located in the system chipset. The GRU + contains memory that can be mmapped into the user address space. This memory is + used to communicate with the GRU to perform functions such as load/store, + scatter/gather, bcopy, AMOs, etc. The GRU is directly accessed by user + instructions using user virtual addresses. GRU instructions (ex., bcopy) use + user virtual addresses for operands. + + If you are not running on a SGI UV system, say N. + +config SGI_GRU_DEBUG + bool "SGI GRU driver debug" + depends on SGI_GRU + help + This option enables additional debugging code for the SGI GRU driver. + If you are unsure, say N. + +config APDS9802ALS + tristate "Medfield Avago APDS9802 ALS Sensor module" + depends on I2C + help + If you say yes here you get support for the ALS APDS9802 ambient + light sensor. + + This driver can also be built as a module. If so, the module + will be called apds9802als. + +config ISL29003 + tristate "Intersil ISL29003 ambient light sensor" + depends on I2C && SYSFS + help + If you say yes here you get support for the Intersil ISL29003 + ambient light sensor. + + This driver can also be built as a module. If so, the module + will be called isl29003. + +config ISL29020 + tristate "Intersil ISL29020 ambient light sensor" + depends on I2C + help + If you say yes here you get support for the Intersil ISL29020 + ambient light sensor. + + This driver can also be built as a module. If so, the module + will be called isl29020. + +config SENSORS_TSL2550 + tristate "Taos TSL2550 ambient light sensor" + depends on I2C && SYSFS + help + If you say yes here you get support for the Taos TSL2550 + ambient light sensor. + + This driver can also be built as a module. If so, the module + will be called tsl2550. + +config SENSORS_BH1770 + tristate "BH1770GLC / SFH7770 combined ALS - Proximity sensor" + depends on I2C + help + Say Y here if you want to build a driver for BH1770GLC (ROHM) or + SFH7770 (Osram) combined ambient light and proximity sensor chip. + + To compile this driver as a module, choose M here: the + module will be called bh1770glc. If unsure, say N here. + +config SENSORS_APDS990X + tristate "APDS990X combined als and proximity sensors" + depends on I2C + help + Say Y here if you want to build a driver for Avago APDS990x + combined ambient light and proximity sensor chip. + + To compile this driver as a module, choose M here: the + module will be called apds990x. If unsure, say N here. + +config HMC6352 + tristate "Honeywell HMC6352 compass" + depends on I2C + help + This driver provides support for the Honeywell HMC6352 compass, + providing configuration and heading data via sysfs. + +config DS1682 + tristate "Dallas DS1682 Total Elapsed Time Recorder with Alarm" + depends on I2C + help + If you say yes here you get support for Dallas Semiconductor + DS1682 Total Elapsed Time Recorder. + + This driver can also be built as a module. If so, the module + will be called ds1682. + +config VMWARE_BALLOON + tristate "VMware Balloon Driver" + depends on VMWARE_VMCI && X86 && HYPERVISOR_GUEST + select MEMORY_BALLOON + help + This is VMware physical memory management driver which acts + like a "balloon" that can be inflated to reclaim physical pages + by reserving them in the guest and invalidating them in the + monitor, freeing up the underlying machine pages so they can + be allocated to other guests. The balloon can also be deflated + to allow the guest to use more physical memory. + + If unsure, say N. + + To compile this driver as a module, choose M here: the + module will be called vmw_balloon. + +config PCH_PHUB + tristate "Intel EG20T PCH/LAPIS Semicon IOH(ML7213/ML7223/ML7831) PHUB" + select GENERIC_NET_UTILS + depends on PCI && (X86_32 || MIPS || COMPILE_TEST) + help + This driver is for PCH(Platform controller Hub) PHUB(Packet Hub) of + Intel Topcliff which is an IOH(Input/Output Hub) for x86 embedded + processor. The Topcliff has MAC address and Option ROM data in SROM. + This driver can access MAC address and Option ROM data in SROM. + + This driver also can be used for LAPIS Semiconductor's IOH, + ML7213/ML7223/ML7831. + ML7213 which is for IVI(In-Vehicle Infotainment) use. + ML7223 IOH is for MP(Media Phone) use. + ML7831 IOH is for general purpose use. + ML7213/ML7223/ML7831 is companion chip for Intel Atom E6xx series. + ML7213/ML7223/ML7831 is completely compatible for Intel EG20T PCH. + + To compile this driver as a module, choose M here: the module will + be called pch_phub. + +config LATTICE_ECP3_CONFIG + tristate "Lattice ECP3 FPGA bitstream configuration via SPI" + depends on SPI && SYSFS + select FW_LOADER + default n + help + This option enables support for bitstream configuration (programming + or loading) of the Lattice ECP3 FPGA family via SPI. + + If unsure, say N. + +config SRAM + bool "Generic on-chip SRAM driver" + depends on HAS_IOMEM + select GENERIC_ALLOCATOR + select SRAM_EXEC if ARM + help + This driver allows you to declare a memory region to be managed by + the genalloc API. It is supposed to be used for small on-chip SRAM + areas found on many SoCs. + +config SRAM_EXEC + bool + +config PCI_ENDPOINT_TEST + depends on PCI + select CRC32 + tristate "PCI Endpoint Test driver" + help + Enable this configuration option to enable the host side test driver + for PCI Endpoint. + +config XILINX_SDFEC + tristate "Xilinx SDFEC 16" + depends on HAS_IOMEM + help + This option enables support for the Xilinx SDFEC (Soft Decision + Forward Error Correction) driver. This enables a char driver + for the SDFEC. + + You may select this driver if your design instantiates the + SDFEC(16nm) hardened block. To compile this as a module choose M. + + If unsure, say N. + +config MISC_RTSX + tristate + default MISC_RTSX_PCI || MISC_RTSX_USB + +config PVPANIC + tristate "pvpanic device support" + depends on HAS_IOMEM && (ACPI || OF) + help + This driver provides support for the pvpanic device. pvpanic is + a paravirtualized device provided by QEMU; it lets a virtual machine + (guest) communicate panic events to the host. + +config HISI_HIKEY_USB + tristate "USB GPIO Hub on HiSilicon Hikey 960/970 Platform" + depends on (OF && GPIOLIB) || COMPILE_TEST + depends on USB_ROLE_SWITCH + help + If you say yes here this adds support for the on-board USB GPIO hub + found on HiKey 960/970 boards, which is necessary to support + switching between the dual-role USB-C port and the USB-A host ports + using only one USB controller. + +source "drivers/misc/c2port/Kconfig" +source "drivers/misc/eeprom/Kconfig" +source "drivers/misc/cb710/Kconfig" +source "drivers/misc/ti-st/Kconfig" +source "drivers/misc/lis3lv02d/Kconfig" +source "drivers/misc/altera-stapl/Kconfig" +source "drivers/misc/mei/Kconfig" +source "drivers/misc/vmw_vmci/Kconfig" +source "drivers/misc/genwqe/Kconfig" +source "drivers/misc/echo/Kconfig" +source "drivers/misc/cxl/Kconfig" +source "drivers/misc/ocxl/Kconfig" +source "drivers/misc/cardreader/Kconfig" +source "drivers/misc/habanalabs/Kconfig" +source "drivers/misc/uacce/Kconfig" +endmenu |