diff options
Diffstat (limited to 'drivers/net/wireless/ti/wl1251/reg.h')
| -rw-r--r-- | drivers/net/wireless/ti/wl1251/reg.h | 641 |
1 files changed, 641 insertions, 0 deletions
diff --git a/drivers/net/wireless/ti/wl1251/reg.h b/drivers/net/wireless/ti/wl1251/reg.h new file mode 100644 index 000000000..890176c91 --- /dev/null +++ b/drivers/net/wireless/ti/wl1251/reg.h @@ -0,0 +1,641 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ +/* + * This file is part of wl12xx + * + * Copyright (c) 1998-2007 Texas Instruments Incorporated + * Copyright (C) 2008 Nokia Corporation + */ + +#ifndef __REG_H__ +#define __REG_H__ + +#include <linux/bitops.h> + +#define REGISTERS_BASE 0x00300000 +#define DRPW_BASE 0x00310000 + +#define REGISTERS_DOWN_SIZE 0x00008800 +#define REGISTERS_WORK_SIZE 0x0000b000 + +#define HW_ACCESS_ELP_CTRL_REG_ADDR 0x1FFFC + +/* ELP register commands */ +#define ELPCTRL_WAKE_UP 0x1 +#define ELPCTRL_WAKE_UP_WLAN_READY 0x5 +#define ELPCTRL_SLEEP 0x0 +/* ELP WLAN_READY bit */ +#define ELPCTRL_WLAN_READY 0x2 + +/* Device Configuration registers*/ +#define SOR_CFG (REGISTERS_BASE + 0x0800) +#define ECPU_CTRL (REGISTERS_BASE + 0x0804) +#define HI_CFG (REGISTERS_BASE + 0x0808) + +/* EEPROM registers */ +#define EE_START (REGISTERS_BASE + 0x080C) +#define EE_CTL (REGISTERS_BASE + 0x2000) +#define EE_DATA (REGISTERS_BASE + 0x2004) +#define EE_ADDR (REGISTERS_BASE + 0x2008) + +#define EE_CTL_READ 2 + +#define CHIP_ID_B (REGISTERS_BASE + 0x5674) + +#define CHIP_ID_1251_PG10 (0x7010101) +#define CHIP_ID_1251_PG11 (0x7020101) +#define CHIP_ID_1251_PG12 (0x7030101) + +#define ENABLE (REGISTERS_BASE + 0x5450) + +/* Power Management registers */ +#define ELP_CFG_MODE (REGISTERS_BASE + 0x5804) +#define ELP_CMD (REGISTERS_BASE + 0x5808) +#define PLL_CAL_TIME (REGISTERS_BASE + 0x5810) +#define CLK_REQ_TIME (REGISTERS_BASE + 0x5814) +#define CLK_BUF_TIME (REGISTERS_BASE + 0x5818) + +#define CFG_PLL_SYNC_CNT (REGISTERS_BASE + 0x5820) + +/* Scratch Pad registers*/ +#define SCR_PAD0 (REGISTERS_BASE + 0x5608) +#define SCR_PAD1 (REGISTERS_BASE + 0x560C) +#define SCR_PAD2 (REGISTERS_BASE + 0x5610) +#define SCR_PAD3 (REGISTERS_BASE + 0x5614) +#define SCR_PAD4 (REGISTERS_BASE + 0x5618) +#define SCR_PAD4_SET (REGISTERS_BASE + 0x561C) +#define SCR_PAD4_CLR (REGISTERS_BASE + 0x5620) +#define SCR_PAD5 (REGISTERS_BASE + 0x5624) +#define SCR_PAD5_SET (REGISTERS_BASE + 0x5628) +#define SCR_PAD5_CLR (REGISTERS_BASE + 0x562C) +#define SCR_PAD6 (REGISTERS_BASE + 0x5630) +#define SCR_PAD7 (REGISTERS_BASE + 0x5634) +#define SCR_PAD8 (REGISTERS_BASE + 0x5638) +#define SCR_PAD9 (REGISTERS_BASE + 0x563C) + +/* Spare registers*/ +#define SPARE_A1 (REGISTERS_BASE + 0x0994) +#define SPARE_A2 (REGISTERS_BASE + 0x0998) +#define SPARE_A3 (REGISTERS_BASE + 0x099C) +#define SPARE_A4 (REGISTERS_BASE + 0x09A0) +#define SPARE_A5 (REGISTERS_BASE + 0x09A4) +#define SPARE_A6 (REGISTERS_BASE + 0x09A8) +#define SPARE_A7 (REGISTERS_BASE + 0x09AC) +#define SPARE_A8 (REGISTERS_BASE + 0x09B0) +#define SPARE_B1 (REGISTERS_BASE + 0x5420) +#define SPARE_B2 (REGISTERS_BASE + 0x5424) +#define SPARE_B3 (REGISTERS_BASE + 0x5428) +#define SPARE_B4 (REGISTERS_BASE + 0x542C) +#define SPARE_B5 (REGISTERS_BASE + 0x5430) +#define SPARE_B6 (REGISTERS_BASE + 0x5434) +#define SPARE_B7 (REGISTERS_BASE + 0x5438) +#define SPARE_B8 (REGISTERS_BASE + 0x543C) + +enum wl12xx_acx_int_reg { + ACX_REG_INTERRUPT_TRIG, + ACX_REG_INTERRUPT_TRIG_H, + +/*============================================= + Host Interrupt Mask Register - 32bit (RW) + ------------------------------------------ + Setting a bit in this register masks the + corresponding interrupt to the host. + 0 - RX0 - Rx first dubble buffer Data Interrupt + 1 - TXD - Tx Data Interrupt + 2 - TXXFR - Tx Transfer Interrupt + 3 - RX1 - Rx second dubble buffer Data Interrupt + 4 - RXXFR - Rx Transfer Interrupt + 5 - EVENT_A - Event Mailbox interrupt + 6 - EVENT_B - Event Mailbox interrupt + 7 - WNONHST - Wake On Host Interrupt + 8 - TRACE_A - Debug Trace interrupt + 9 - TRACE_B - Debug Trace interrupt + 10 - CDCMP - Command Complete Interrupt + 11 - + 12 - + 13 - + 14 - ICOMP - Initialization Complete Interrupt + 16 - SG SE - Soft Gemini - Sense enable interrupt + 17 - SG SD - Soft Gemini - Sense disable interrupt + 18 - - + 19 - - + 20 - - + 21- - + Default: 0x0001 +*==============================================*/ + ACX_REG_INTERRUPT_MASK, + +/*============================================= + Host Interrupt Mask Set 16bit, (Write only) + ------------------------------------------ + Setting a bit in this register sets + the corresponding bin in ACX_HINT_MASK register + without effecting the mask + state of other bits (0 = no effect). +==============================================*/ + ACX_REG_HINT_MASK_SET, + +/*============================================= + Host Interrupt Mask Clear 16bit,(Write only) + ------------------------------------------ + Setting a bit in this register clears + the corresponding bin in ACX_HINT_MASK register + without effecting the mask + state of other bits (0 = no effect). +=============================================*/ + ACX_REG_HINT_MASK_CLR, + +/*============================================= + Host Interrupt Status Nondestructive Read + 16bit,(Read only) + ------------------------------------------ + The host can read this register to determine + which interrupts are active. + Reading this register doesn't + effect its content. +=============================================*/ + ACX_REG_INTERRUPT_NO_CLEAR, + +/*============================================= + Host Interrupt Status Clear on Read Register + 16bit,(Read only) + ------------------------------------------ + The host can read this register to determine + which interrupts are active. + Reading this register clears it, + thus making all interrupts inactive. +==============================================*/ + ACX_REG_INTERRUPT_CLEAR, + +/*============================================= + Host Interrupt Acknowledge Register + 16bit,(Write only) + ------------------------------------------ + The host can set individual bits in this + register to clear (acknowledge) the corresp. + interrupt status bits in the HINT_STS_CLR and + HINT_STS_ND registers, thus making the + assotiated interrupt inactive. (0-no effect) +==============================================*/ + ACX_REG_INTERRUPT_ACK, + +/*=============================================== + Host Software Reset - 32bit RW + ------------------------------------------ + [31:1] Reserved + 0 SOFT_RESET Soft Reset - When this bit is set, + it holds the Wlan hardware in a soft reset state. + This reset disables all MAC and baseband processor + clocks except the CardBus/PCI interface clock. + It also initializes all MAC state machines except + the host interface. It does not reload the + contents of the EEPROM. When this bit is cleared + (not self-clearing), the Wlan hardware + exits the software reset state. +===============================================*/ + ACX_REG_SLV_SOFT_RESET, + +/*=============================================== + EEPROM Burst Read Start - 32bit RW + ------------------------------------------ + [31:1] Reserved + 0 ACX_EE_START - EEPROM Burst Read Start 0 + Setting this bit starts a burst read from + the external EEPROM. + If this bit is set (after reset) before an EEPROM read/write, + the burst read starts at EEPROM address 0. + Otherwise, it starts at the address + following the address of the previous access. + TheWlan hardware hardware clears this bit automatically. + + Default: 0x00000000 +*================================================*/ + ACX_REG_EE_START, + +/* Embedded ARM CPU Control */ + +/*=============================================== + Halt eCPU - 32bit RW + ------------------------------------------ + 0 HALT_ECPU Halt Embedded CPU - This bit is the + complement of bit 1 (MDATA2) in the SOR_CFG register. + During a hardware reset, this bit holds + the inverse of MDATA2. + When downloading firmware from the host, + set this bit (pull down MDATA2). + The host clears this bit after downloading the firmware into + zero-wait-state SSRAM. + When loading firmware from Flash, clear this bit (pull up MDATA2) + so that the eCPU can run the bootloader code in Flash + HALT_ECPU eCPU State + -------------------- + 1 halt eCPU + 0 enable eCPU + ===============================================*/ + ACX_REG_ECPU_CONTROL, + + ACX_REG_TABLE_LEN +}; + +#define ACX_SLV_SOFT_RESET_BIT BIT(0) +#define ACX_REG_EEPROM_START_BIT BIT(0) + +/* Command/Information Mailbox Pointers */ + +/*=============================================== + Command Mailbox Pointer - 32bit RW + ------------------------------------------ + This register holds the start address of + the command mailbox located in the Wlan hardware memory. + The host must read this pointer after a reset to + find the location of the command mailbox. + The Wlan hardware initializes the command mailbox + pointer with the default address of the command mailbox. + The command mailbox pointer is not valid until after + the host receives the Init Complete interrupt from + the Wlan hardware. + ===============================================*/ +#define REG_COMMAND_MAILBOX_PTR (SCR_PAD0) + +/*=============================================== + Information Mailbox Pointer - 32bit RW + ------------------------------------------ + This register holds the start address of + the information mailbox located in the Wlan hardware memory. + The host must read this pointer after a reset to find + the location of the information mailbox. + The Wlan hardware initializes the information mailbox pointer + with the default address of the information mailbox. + The information mailbox pointer is not valid + until after the host receives the Init Complete interrupt from + the Wlan hardware. + ===============================================*/ +#define REG_EVENT_MAILBOX_PTR (SCR_PAD1) + + +/* Misc */ + +#define REG_ENABLE_TX_RX (ENABLE) +/* + * Rx configuration (filter) information element + * --------------------------------------------- + */ +#define REG_RX_CONFIG (RX_CFG) +#define REG_RX_FILTER (RX_FILTER_CFG) + + +#define RX_CFG_ENABLE_PHY_HEADER_PLCP 0x0002 + +/* promiscuous - receives all valid frames */ +#define RX_CFG_PROMISCUOUS 0x0008 + +/* receives frames from any BSSID */ +#define RX_CFG_BSSID 0x0020 + +/* receives frames destined to any MAC address */ +#define RX_CFG_MAC 0x0010 + +#define RX_CFG_ENABLE_ONLY_MY_DEST_MAC 0x0010 +#define RX_CFG_ENABLE_ANY_DEST_MAC 0x0000 +#define RX_CFG_ENABLE_ONLY_MY_BSSID 0x0020 +#define RX_CFG_ENABLE_ANY_BSSID 0x0000 + +/* discards all broadcast frames */ +#define RX_CFG_DISABLE_BCAST 0x0200 + +#define RX_CFG_ENABLE_ONLY_MY_SSID 0x0400 +#define RX_CFG_ENABLE_RX_CMPLT_FCS_ERROR 0x0800 +#define RX_CFG_COPY_RX_STATUS 0x2000 +#define RX_CFG_TSF 0x10000 + +#define RX_CONFIG_OPTION_ANY_DST_MY_BSS (RX_CFG_ENABLE_ANY_DEST_MAC | \ + RX_CFG_ENABLE_ONLY_MY_BSSID) + +#define RX_CONFIG_OPTION_MY_DST_ANY_BSS (RX_CFG_ENABLE_ONLY_MY_DEST_MAC\ + | RX_CFG_ENABLE_ANY_BSSID) + +#define RX_CONFIG_OPTION_ANY_DST_ANY_BSS (RX_CFG_ENABLE_ANY_DEST_MAC | \ + RX_CFG_ENABLE_ANY_BSSID) + +#define RX_CONFIG_OPTION_MY_DST_MY_BSS (RX_CFG_ENABLE_ONLY_MY_DEST_MAC\ + | RX_CFG_ENABLE_ONLY_MY_BSSID) + +#define RX_CONFIG_OPTION_FOR_SCAN (RX_CFG_ENABLE_PHY_HEADER_PLCP \ + | RX_CFG_ENABLE_RX_CMPLT_FCS_ERROR \ + | RX_CFG_COPY_RX_STATUS | RX_CFG_TSF) + +#define RX_CONFIG_OPTION_FOR_MEASUREMENT (RX_CFG_ENABLE_ANY_DEST_MAC) + +#define RX_CONFIG_OPTION_FOR_JOIN (RX_CFG_ENABLE_ONLY_MY_BSSID | \ + RX_CFG_ENABLE_ONLY_MY_DEST_MAC) + +#define RX_CONFIG_OPTION_FOR_IBSS_JOIN (RX_CFG_ENABLE_ONLY_MY_SSID | \ + RX_CFG_ENABLE_ONLY_MY_DEST_MAC) + +#define RX_FILTER_OPTION_DEF (CFG_RX_MGMT_EN | CFG_RX_DATA_EN\ + | CFG_RX_CTL_EN | CFG_RX_BCN_EN\ + | CFG_RX_AUTH_EN | CFG_RX_ASSOC_EN) + +#define RX_FILTER_OPTION_FILTER_ALL 0 + +#define RX_FILTER_OPTION_DEF_PRSP_BCN (CFG_RX_PRSP_EN | CFG_RX_MGMT_EN\ + | CFG_RX_RCTS_ACK | CFG_RX_BCN_EN) + +#define RX_FILTER_OPTION_JOIN (CFG_RX_MGMT_EN | CFG_RX_DATA_EN\ + | CFG_RX_BCN_EN | CFG_RX_AUTH_EN\ + | CFG_RX_ASSOC_EN | CFG_RX_RCTS_ACK\ + | CFG_RX_PRSP_EN) + + +/*=============================================== + EEPROM Read/Write Request 32bit RW + ------------------------------------------ + 1 EE_READ - EEPROM Read Request 1 - Setting this bit + loads a single byte of data into the EE_DATA + register from the EEPROM location specified in + the EE_ADDR register. + The Wlan hardware hardware clears this bit automatically. + EE_DATA is valid when this bit is cleared. + + 0 EE_WRITE - EEPROM Write Request - Setting this bit + writes a single byte of data from the EE_DATA register into the + EEPROM location specified in the EE_ADDR register. + The Wlan hardware hardware clears this bit automatically. +*===============================================*/ +#define EE_CTL (REGISTERS_BASE + 0x2000) +#define ACX_EE_CTL_REG EE_CTL +#define EE_WRITE 0x00000001ul +#define EE_READ 0x00000002ul + +/*=============================================== + EEPROM Address - 32bit RW + ------------------------------------------ + This register specifies the address + within the EEPROM from/to which to read/write data. + ===============================================*/ +#define EE_ADDR (REGISTERS_BASE + 0x2008) +#define ACX_EE_ADDR_REG EE_ADDR + +/*=============================================== + EEPROM Data - 32bit RW + ------------------------------------------ + This register either holds the read 8 bits of + data from the EEPROM or the write data + to be written to the EEPROM. + ===============================================*/ +#define EE_DATA (REGISTERS_BASE + 0x2004) +#define ACX_EE_DATA_REG EE_DATA + +#define EEPROM_ACCESS_TO 10000 /* timeout counter */ +#define START_EEPROM_MGR 0x00000001 + +/*=============================================== + EEPROM Base Address - 32bit RW + ------------------------------------------ + This register holds the upper nine bits + [23:15] of the 24-bit Wlan hardware memory + address for burst reads from EEPROM accesses. + The EEPROM provides the lower 15 bits of this address. + The MSB of the address from the EEPROM is ignored. + ===============================================*/ +#define ACX_EE_CFG EE_CFG + +/*=============================================== + GPIO Output Values -32bit, RW + ------------------------------------------ + [31:16] Reserved + [15: 0] Specify the output values (at the output driver inputs) for + GPIO[15:0], respectively. + ===============================================*/ +#define ACX_GPIO_OUT_REG GPIO_OUT +#define ACX_MAX_GPIO_LINES 15 + +/*=============================================== + Contention window -32bit, RW + ------------------------------------------ + [31:26] Reserved + [25:16] Max (0x3ff) + [15:07] Reserved + [06:00] Current contention window value - default is 0x1F + ===============================================*/ +#define ACX_CONT_WIND_CFG_REG CONT_WIND_CFG +#define ACX_CONT_WIND_MIN_MASK 0x0000007f +#define ACX_CONT_WIND_MAX 0x03ff0000 + +/*=============================================== + HI_CFG Interface Configuration Register Values + ------------------------------------------ + ===============================================*/ +#define HI_CFG_UART_ENABLE 0x00000004 +#define HI_CFG_RST232_ENABLE 0x00000008 +#define HI_CFG_CLOCK_REQ_SELECT 0x00000010 +#define HI_CFG_HOST_INT_ENABLE 0x00000020 +#define HI_CFG_VLYNQ_OUTPUT_ENABLE 0x00000040 +#define HI_CFG_HOST_INT_ACTIVE_LOW 0x00000080 +#define HI_CFG_UART_TX_OUT_GPIO_15 0x00000100 +#define HI_CFG_UART_TX_OUT_GPIO_14 0x00000200 +#define HI_CFG_UART_TX_OUT_GPIO_7 0x00000400 + +/* + * NOTE: USE_ACTIVE_HIGH compilation flag should be defined in makefile + * for platforms using active high interrupt level + */ +#ifdef USE_ACTIVE_HIGH +#define HI_CFG_DEF_VAL \ + (HI_CFG_UART_ENABLE | \ + HI_CFG_RST232_ENABLE | \ + HI_CFG_CLOCK_REQ_SELECT | \ + HI_CFG_HOST_INT_ENABLE) +#else +#define HI_CFG_DEF_VAL \ + (HI_CFG_UART_ENABLE | \ + HI_CFG_RST232_ENABLE | \ + HI_CFG_CLOCK_REQ_SELECT | \ + HI_CFG_HOST_INT_ENABLE) + +#endif + +#define REF_FREQ_19_2 0 +#define REF_FREQ_26_0 1 +#define REF_FREQ_38_4 2 +#define REF_FREQ_40_0 3 +#define REF_FREQ_33_6 4 +#define REF_FREQ_NUM 5 + +#define LUT_PARAM_INTEGER_DIVIDER 0 +#define LUT_PARAM_FRACTIONAL_DIVIDER 1 +#define LUT_PARAM_ATTN_BB 2 +#define LUT_PARAM_ALPHA_BB 3 +#define LUT_PARAM_STOP_TIME_BB 4 +#define LUT_PARAM_BB_PLL_LOOP_FILTER 5 +#define LUT_PARAM_NUM 6 + +#define ACX_EEPROMLESS_IND_REG (SCR_PAD4) +#define USE_EEPROM 0 +#define SOFT_RESET_MAX_TIME 1000000 +#define SOFT_RESET_STALL_TIME 1000 +#define NVS_DATA_BUNDARY_ALIGNMENT 4 + + +/* Firmware image load chunk size */ +#define CHUNK_SIZE 512 + +/* Firmware image header size */ +#define FW_HDR_SIZE 8 + +#define ECPU_CONTROL_HALT 0x00000101 + + +/****************************************************************************** + + CHANNELS, BAND & REG DOMAINS definitions + +******************************************************************************/ + + +enum { + RADIO_BAND_2_4GHZ = 0, /* 2.4 Ghz band */ + RADIO_BAND_5GHZ = 1, /* 5 Ghz band */ + RADIO_BAND_JAPAN_4_9_GHZ = 2, + DEFAULT_BAND = RADIO_BAND_2_4GHZ, + INVALID_BAND = 0xFE, + MAX_RADIO_BANDS = 0xFF +}; + +enum { + NO_RATE = 0, + RATE_1MBPS = 0x0A, + RATE_2MBPS = 0x14, + RATE_5_5MBPS = 0x37, + RATE_6MBPS = 0x0B, + RATE_9MBPS = 0x0F, + RATE_11MBPS = 0x6E, + RATE_12MBPS = 0x0A, + RATE_18MBPS = 0x0E, + RATE_22MBPS = 0xDC, + RATE_24MBPS = 0x09, + RATE_36MBPS = 0x0D, + RATE_48MBPS = 0x08, + RATE_54MBPS = 0x0C +}; + +enum { + RATE_INDEX_1MBPS = 0, + RATE_INDEX_2MBPS = 1, + RATE_INDEX_5_5MBPS = 2, + RATE_INDEX_6MBPS = 3, + RATE_INDEX_9MBPS = 4, + RATE_INDEX_11MBPS = 5, + RATE_INDEX_12MBPS = 6, + RATE_INDEX_18MBPS = 7, + RATE_INDEX_22MBPS = 8, + RATE_INDEX_24MBPS = 9, + RATE_INDEX_36MBPS = 10, + RATE_INDEX_48MBPS = 11, + RATE_INDEX_54MBPS = 12, + RATE_INDEX_MAX = RATE_INDEX_54MBPS, + MAX_RATE_INDEX, + INVALID_RATE_INDEX = MAX_RATE_INDEX, + RATE_INDEX_ENUM_MAX_SIZE = 0x7FFFFFFF +}; + +enum { + RATE_MASK_1MBPS = 0x1, + RATE_MASK_2MBPS = 0x2, + RATE_MASK_5_5MBPS = 0x4, + RATE_MASK_11MBPS = 0x20, +}; + +#define SHORT_PREAMBLE_BIT BIT(0) /* CCK or Barker depending on the rate */ +#define OFDM_RATE_BIT BIT(6) +#define PBCC_RATE_BIT BIT(7) + +enum { + CCK_LONG = 0, + CCK_SHORT = SHORT_PREAMBLE_BIT, + PBCC_LONG = PBCC_RATE_BIT, + PBCC_SHORT = PBCC_RATE_BIT | SHORT_PREAMBLE_BIT, + OFDM = OFDM_RATE_BIT +}; + +/****************************************************************************** + +Transmit-Descriptor RATE-SET field definitions... + +Define a new "Rate-Set" for TX path that incorporates the +Rate & Modulation info into a single 16-bit field. + +TxdRateSet_t: +b15 - Indicates Preamble type (1=SHORT, 0=LONG). + Notes: + Must be LONG (0) for 1Mbps rate. + Does not apply (set to 0) for RevG-OFDM rates. +b14 - Indicates PBCC encoding (1=PBCC, 0=not). + Notes: + Does not apply (set to 0) for rates 1 and 2 Mbps. + Does not apply (set to 0) for RevG-OFDM rates. +b13 - Unused (set to 0). +b12-b0 - Supported Rate indicator bits as defined below. + +******************************************************************************/ + + +/************************************************************************* + + Interrupt Trigger Register (Host -> WiLink) + +**************************************************************************/ + +/* Hardware to Embedded CPU Interrupts - first 32-bit register set */ + +/* + * Host Command Interrupt. Setting this bit masks + * the interrupt that the host issues to inform + * the FW that it has sent a command + * to the Wlan hardware Command Mailbox. + */ +#define INTR_TRIG_CMD BIT(0) + +/* + * Host Event Acknowlegde Interrupt. The host + * sets this bit to acknowledge that it received + * the unsolicited information from the event + * mailbox. + */ +#define INTR_TRIG_EVENT_ACK BIT(1) + +/* + * The host sets this bit to inform the Wlan + * FW that a TX packet is in the XFER + * Buffer #0. + */ +#define INTR_TRIG_TX_PROC0 BIT(2) + +/* + * The host sets this bit to inform the FW + * that it read a packet from RX XFER + * Buffer #0. + */ +#define INTR_TRIG_RX_PROC0 BIT(3) + +#define INTR_TRIG_DEBUG_ACK BIT(4) + +#define INTR_TRIG_STATE_CHANGED BIT(5) + + +/* Hardware to Embedded CPU Interrupts - second 32-bit register set */ + +/* + * The host sets this bit to inform the FW + * that it read a packet from RX XFER + * Buffer #1. + */ +#define INTR_TRIG_RX_PROC1 BIT(17) + +/* + * The host sets this bit to inform the Wlan + * hardware that a TX packet is in the XFER + * Buffer #1. + */ +#define INTR_TRIG_TX_PROC1 BIT(18) + +#endif |