diff options
Diffstat (limited to '')
| -rw-r--r-- | drivers/tty/serial/sa1100.c | 950 |
1 files changed, 950 insertions, 0 deletions
diff --git a/drivers/tty/serial/sa1100.c b/drivers/tty/serial/sa1100.c new file mode 100644 index 000000000..aa1cf2ae1 --- /dev/null +++ b/drivers/tty/serial/sa1100.c @@ -0,0 +1,950 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Driver for SA11x0 serial ports + * + * Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o. + * + * Copyright (C) 2000 Deep Blue Solutions Ltd. + */ + +#include <linux/module.h> +#include <linux/ioport.h> +#include <linux/init.h> +#include <linux/console.h> +#include <linux/sysrq.h> +#include <linux/platform_data/sa11x0-serial.h> +#include <linux/platform_device.h> +#include <linux/tty.h> +#include <linux/tty_flip.h> +#include <linux/serial_core.h> +#include <linux/serial.h> +#include <linux/io.h> + +#include <asm/irq.h> +#include <mach/hardware.h> +#include <mach/irqs.h> + +#include "serial_mctrl_gpio.h" + +/* We've been assigned a range on the "Low-density serial ports" major */ +#define SERIAL_SA1100_MAJOR 204 +#define MINOR_START 5 + +#define NR_PORTS 3 + +#define SA1100_ISR_PASS_LIMIT 256 + +/* + * Convert from ignore_status_mask or read_status_mask to UTSR[01] + */ +#define SM_TO_UTSR0(x) ((x) & 0xff) +#define SM_TO_UTSR1(x) ((x) >> 8) +#define UTSR0_TO_SM(x) ((x)) +#define UTSR1_TO_SM(x) ((x) << 8) + +#define UART_GET_UTCR0(sport) __raw_readl((sport)->port.membase + UTCR0) +#define UART_GET_UTCR1(sport) __raw_readl((sport)->port.membase + UTCR1) +#define UART_GET_UTCR2(sport) __raw_readl((sport)->port.membase + UTCR2) +#define UART_GET_UTCR3(sport) __raw_readl((sport)->port.membase + UTCR3) +#define UART_GET_UTSR0(sport) __raw_readl((sport)->port.membase + UTSR0) +#define UART_GET_UTSR1(sport) __raw_readl((sport)->port.membase + UTSR1) +#define UART_GET_CHAR(sport) __raw_readl((sport)->port.membase + UTDR) + +#define UART_PUT_UTCR0(sport,v) __raw_writel((v),(sport)->port.membase + UTCR0) +#define UART_PUT_UTCR1(sport,v) __raw_writel((v),(sport)->port.membase + UTCR1) +#define UART_PUT_UTCR2(sport,v) __raw_writel((v),(sport)->port.membase + UTCR2) +#define UART_PUT_UTCR3(sport,v) __raw_writel((v),(sport)->port.membase + UTCR3) +#define UART_PUT_UTSR0(sport,v) __raw_writel((v),(sport)->port.membase + UTSR0) +#define UART_PUT_UTSR1(sport,v) __raw_writel((v),(sport)->port.membase + UTSR1) +#define UART_PUT_CHAR(sport,v) __raw_writel((v),(sport)->port.membase + UTDR) + +/* + * This is the size of our serial port register set. + */ +#define UART_PORT_SIZE 0x24 + +/* + * This determines how often we check the modem status signals + * for any change. They generally aren't connected to an IRQ + * so we have to poll them. We also check immediately before + * filling the TX fifo incase CTS has been dropped. + */ +#define MCTRL_TIMEOUT (250*HZ/1000) + +struct sa1100_port { + struct uart_port port; + struct timer_list timer; + unsigned int old_status; + struct mctrl_gpios *gpios; +}; + +/* + * Handle any change of modem status signal since we were last called. + */ +static void sa1100_mctrl_check(struct sa1100_port *sport) +{ + unsigned int status, changed; + + status = sport->port.ops->get_mctrl(&sport->port); + changed = status ^ sport->old_status; + + if (changed == 0) + return; + + sport->old_status = status; + + if (changed & TIOCM_RI) + sport->port.icount.rng++; + if (changed & TIOCM_DSR) + sport->port.icount.dsr++; + if (changed & TIOCM_CAR) + uart_handle_dcd_change(&sport->port, status & TIOCM_CAR); + if (changed & TIOCM_CTS) + uart_handle_cts_change(&sport->port, status & TIOCM_CTS); + + wake_up_interruptible(&sport->port.state->port.delta_msr_wait); +} + +/* + * This is our per-port timeout handler, for checking the + * modem status signals. + */ +static void sa1100_timeout(struct timer_list *t) +{ + struct sa1100_port *sport = from_timer(sport, t, timer); + unsigned long flags; + + if (sport->port.state) { + spin_lock_irqsave(&sport->port.lock, flags); + sa1100_mctrl_check(sport); + spin_unlock_irqrestore(&sport->port.lock, flags); + + mod_timer(&sport->timer, jiffies + MCTRL_TIMEOUT); + } +} + +/* + * interrupts disabled on entry + */ +static void sa1100_stop_tx(struct uart_port *port) +{ + struct sa1100_port *sport = + container_of(port, struct sa1100_port, port); + u32 utcr3; + + utcr3 = UART_GET_UTCR3(sport); + UART_PUT_UTCR3(sport, utcr3 & ~UTCR3_TIE); + sport->port.read_status_mask &= ~UTSR0_TO_SM(UTSR0_TFS); +} + +/* + * port locked and interrupts disabled + */ +static void sa1100_start_tx(struct uart_port *port) +{ + struct sa1100_port *sport = + container_of(port, struct sa1100_port, port); + u32 utcr3; + + utcr3 = UART_GET_UTCR3(sport); + sport->port.read_status_mask |= UTSR0_TO_SM(UTSR0_TFS); + UART_PUT_UTCR3(sport, utcr3 | UTCR3_TIE); +} + +/* + * Interrupts enabled + */ +static void sa1100_stop_rx(struct uart_port *port) +{ + struct sa1100_port *sport = + container_of(port, struct sa1100_port, port); + u32 utcr3; + + utcr3 = UART_GET_UTCR3(sport); + UART_PUT_UTCR3(sport, utcr3 & ~UTCR3_RIE); +} + +/* + * Set the modem control timer to fire immediately. + */ +static void sa1100_enable_ms(struct uart_port *port) +{ + struct sa1100_port *sport = + container_of(port, struct sa1100_port, port); + + mod_timer(&sport->timer, jiffies); + + mctrl_gpio_enable_ms(sport->gpios); +} + +static void +sa1100_rx_chars(struct sa1100_port *sport) +{ + unsigned int status, ch, flg; + + status = UTSR1_TO_SM(UART_GET_UTSR1(sport)) | + UTSR0_TO_SM(UART_GET_UTSR0(sport)); + while (status & UTSR1_TO_SM(UTSR1_RNE)) { + ch = UART_GET_CHAR(sport); + + sport->port.icount.rx++; + + flg = TTY_NORMAL; + + /* + * note that the error handling code is + * out of the main execution path + */ + if (status & UTSR1_TO_SM(UTSR1_PRE | UTSR1_FRE | UTSR1_ROR)) { + if (status & UTSR1_TO_SM(UTSR1_PRE)) + sport->port.icount.parity++; + else if (status & UTSR1_TO_SM(UTSR1_FRE)) + sport->port.icount.frame++; + if (status & UTSR1_TO_SM(UTSR1_ROR)) + sport->port.icount.overrun++; + + status &= sport->port.read_status_mask; + + if (status & UTSR1_TO_SM(UTSR1_PRE)) + flg = TTY_PARITY; + else if (status & UTSR1_TO_SM(UTSR1_FRE)) + flg = TTY_FRAME; + + sport->port.sysrq = 0; + } + + if (uart_handle_sysrq_char(&sport->port, ch)) + goto ignore_char; + + uart_insert_char(&sport->port, status, UTSR1_TO_SM(UTSR1_ROR), ch, flg); + + ignore_char: + status = UTSR1_TO_SM(UART_GET_UTSR1(sport)) | + UTSR0_TO_SM(UART_GET_UTSR0(sport)); + } + + spin_unlock(&sport->port.lock); + tty_flip_buffer_push(&sport->port.state->port); + spin_lock(&sport->port.lock); +} + +static void sa1100_tx_chars(struct sa1100_port *sport) +{ + struct circ_buf *xmit = &sport->port.state->xmit; + + if (sport->port.x_char) { + UART_PUT_CHAR(sport, sport->port.x_char); + sport->port.icount.tx++; + sport->port.x_char = 0; + return; + } + + /* + * Check the modem control lines before + * transmitting anything. + */ + sa1100_mctrl_check(sport); + + if (uart_circ_empty(xmit) || uart_tx_stopped(&sport->port)) { + sa1100_stop_tx(&sport->port); + return; + } + + /* + * Tried using FIFO (not checking TNF) for fifo fill: + * still had the '4 bytes repeated' problem. + */ + while (UART_GET_UTSR1(sport) & UTSR1_TNF) { + UART_PUT_CHAR(sport, xmit->buf[xmit->tail]); + xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1); + sport->port.icount.tx++; + if (uart_circ_empty(xmit)) + break; + } + + if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS) + uart_write_wakeup(&sport->port); + + if (uart_circ_empty(xmit)) + sa1100_stop_tx(&sport->port); +} + +static irqreturn_t sa1100_int(int irq, void *dev_id) +{ + struct sa1100_port *sport = dev_id; + unsigned int status, pass_counter = 0; + + spin_lock(&sport->port.lock); + status = UART_GET_UTSR0(sport); + status &= SM_TO_UTSR0(sport->port.read_status_mask) | ~UTSR0_TFS; + do { + if (status & (UTSR0_RFS | UTSR0_RID)) { + /* Clear the receiver idle bit, if set */ + if (status & UTSR0_RID) + UART_PUT_UTSR0(sport, UTSR0_RID); + sa1100_rx_chars(sport); + } + + /* Clear the relevant break bits */ + if (status & (UTSR0_RBB | UTSR0_REB)) + UART_PUT_UTSR0(sport, status & (UTSR0_RBB | UTSR0_REB)); + + if (status & UTSR0_RBB) + sport->port.icount.brk++; + + if (status & UTSR0_REB) + uart_handle_break(&sport->port); + + if (status & UTSR0_TFS) + sa1100_tx_chars(sport); + if (pass_counter++ > SA1100_ISR_PASS_LIMIT) + break; + status = UART_GET_UTSR0(sport); + status &= SM_TO_UTSR0(sport->port.read_status_mask) | + ~UTSR0_TFS; + } while (status & (UTSR0_TFS | UTSR0_RFS | UTSR0_RID)); + spin_unlock(&sport->port.lock); + + return IRQ_HANDLED; +} + +/* + * Return TIOCSER_TEMT when transmitter is not busy. + */ +static unsigned int sa1100_tx_empty(struct uart_port *port) +{ + struct sa1100_port *sport = + container_of(port, struct sa1100_port, port); + + return UART_GET_UTSR1(sport) & UTSR1_TBY ? 0 : TIOCSER_TEMT; +} + +static unsigned int sa1100_get_mctrl(struct uart_port *port) +{ + struct sa1100_port *sport = + container_of(port, struct sa1100_port, port); + int ret = TIOCM_CTS | TIOCM_DSR | TIOCM_CAR; + + mctrl_gpio_get(sport->gpios, &ret); + + return ret; +} + +static void sa1100_set_mctrl(struct uart_port *port, unsigned int mctrl) +{ + struct sa1100_port *sport = + container_of(port, struct sa1100_port, port); + + mctrl_gpio_set(sport->gpios, mctrl); +} + +/* + * Interrupts always disabled. + */ +static void sa1100_break_ctl(struct uart_port *port, int break_state) +{ + struct sa1100_port *sport = + container_of(port, struct sa1100_port, port); + unsigned long flags; + unsigned int utcr3; + + spin_lock_irqsave(&sport->port.lock, flags); + utcr3 = UART_GET_UTCR3(sport); + if (break_state == -1) + utcr3 |= UTCR3_BRK; + else + utcr3 &= ~UTCR3_BRK; + UART_PUT_UTCR3(sport, utcr3); + spin_unlock_irqrestore(&sport->port.lock, flags); +} + +static int sa1100_startup(struct uart_port *port) +{ + struct sa1100_port *sport = + container_of(port, struct sa1100_port, port); + int retval; + + /* + * Allocate the IRQ + */ + retval = request_irq(sport->port.irq, sa1100_int, 0, + "sa11x0-uart", sport); + if (retval) + return retval; + + /* + * Finally, clear and enable interrupts + */ + UART_PUT_UTSR0(sport, -1); + UART_PUT_UTCR3(sport, UTCR3_RXE | UTCR3_TXE | UTCR3_RIE); + + /* + * Enable modem status interrupts + */ + spin_lock_irq(&sport->port.lock); + sa1100_enable_ms(&sport->port); + spin_unlock_irq(&sport->port.lock); + + return 0; +} + +static void sa1100_shutdown(struct uart_port *port) +{ + struct sa1100_port *sport = + container_of(port, struct sa1100_port, port); + + /* + * Stop our timer. + */ + del_timer_sync(&sport->timer); + + /* + * Free the interrupt + */ + free_irq(sport->port.irq, sport); + + /* + * Disable all interrupts, port and break condition. + */ + UART_PUT_UTCR3(sport, 0); +} + +static void +sa1100_set_termios(struct uart_port *port, struct ktermios *termios, + struct ktermios *old) +{ + struct sa1100_port *sport = + container_of(port, struct sa1100_port, port); + unsigned long flags; + unsigned int utcr0, old_utcr3, baud, quot; + unsigned int old_csize = old ? old->c_cflag & CSIZE : CS8; + + /* + * We only support CS7 and CS8. + */ + while ((termios->c_cflag & CSIZE) != CS7 && + (termios->c_cflag & CSIZE) != CS8) { + termios->c_cflag &= ~CSIZE; + termios->c_cflag |= old_csize; + old_csize = CS8; + } + + if ((termios->c_cflag & CSIZE) == CS8) + utcr0 = UTCR0_DSS; + else + utcr0 = 0; + + if (termios->c_cflag & CSTOPB) + utcr0 |= UTCR0_SBS; + if (termios->c_cflag & PARENB) { + utcr0 |= UTCR0_PE; + if (!(termios->c_cflag & PARODD)) + utcr0 |= UTCR0_OES; + } + + /* + * Ask the core to calculate the divisor for us. + */ + baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16); + quot = uart_get_divisor(port, baud); + + del_timer_sync(&sport->timer); + + spin_lock_irqsave(&sport->port.lock, flags); + + sport->port.read_status_mask &= UTSR0_TO_SM(UTSR0_TFS); + sport->port.read_status_mask |= UTSR1_TO_SM(UTSR1_ROR); + if (termios->c_iflag & INPCK) + sport->port.read_status_mask |= + UTSR1_TO_SM(UTSR1_FRE | UTSR1_PRE); + if (termios->c_iflag & (BRKINT | PARMRK)) + sport->port.read_status_mask |= + UTSR0_TO_SM(UTSR0_RBB | UTSR0_REB); + + /* + * Characters to ignore + */ + sport->port.ignore_status_mask = 0; + if (termios->c_iflag & IGNPAR) + sport->port.ignore_status_mask |= + UTSR1_TO_SM(UTSR1_FRE | UTSR1_PRE); + if (termios->c_iflag & IGNBRK) { + sport->port.ignore_status_mask |= + UTSR0_TO_SM(UTSR0_RBB | UTSR0_REB); + /* + * If we're ignoring parity and break indicators, + * ignore overruns too (for real raw support). + */ + if (termios->c_iflag & IGNPAR) + sport->port.ignore_status_mask |= + UTSR1_TO_SM(UTSR1_ROR); + } + + /* + * Update the per-port timeout. + */ + uart_update_timeout(port, termios->c_cflag, baud); + + /* + * disable interrupts and drain transmitter + */ + old_utcr3 = UART_GET_UTCR3(sport); + UART_PUT_UTCR3(sport, old_utcr3 & ~(UTCR3_RIE | UTCR3_TIE)); + + while (UART_GET_UTSR1(sport) & UTSR1_TBY) + barrier(); + + /* then, disable everything */ + UART_PUT_UTCR3(sport, 0); + + /* set the parity, stop bits and data size */ + UART_PUT_UTCR0(sport, utcr0); + + /* set the baud rate */ + quot -= 1; + UART_PUT_UTCR1(sport, ((quot & 0xf00) >> 8)); + UART_PUT_UTCR2(sport, (quot & 0xff)); + + UART_PUT_UTSR0(sport, -1); + + UART_PUT_UTCR3(sport, old_utcr3); + + if (UART_ENABLE_MS(&sport->port, termios->c_cflag)) + sa1100_enable_ms(&sport->port); + + spin_unlock_irqrestore(&sport->port.lock, flags); +} + +static const char *sa1100_type(struct uart_port *port) +{ + struct sa1100_port *sport = + container_of(port, struct sa1100_port, port); + + return sport->port.type == PORT_SA1100 ? "SA1100" : NULL; +} + +/* + * Release the memory region(s) being used by 'port'. + */ +static void sa1100_release_port(struct uart_port *port) +{ + struct sa1100_port *sport = + container_of(port, struct sa1100_port, port); + + release_mem_region(sport->port.mapbase, UART_PORT_SIZE); +} + +/* + * Request the memory region(s) being used by 'port'. + */ +static int sa1100_request_port(struct uart_port *port) +{ + struct sa1100_port *sport = + container_of(port, struct sa1100_port, port); + + return request_mem_region(sport->port.mapbase, UART_PORT_SIZE, + "sa11x0-uart") != NULL ? 0 : -EBUSY; +} + +/* + * Configure/autoconfigure the port. + */ +static void sa1100_config_port(struct uart_port *port, int flags) +{ + struct sa1100_port *sport = + container_of(port, struct sa1100_port, port); + + if (flags & UART_CONFIG_TYPE && + sa1100_request_port(&sport->port) == 0) + sport->port.type = PORT_SA1100; +} + +/* + * Verify the new serial_struct (for TIOCSSERIAL). + * The only change we allow are to the flags and type, and + * even then only between PORT_SA1100 and PORT_UNKNOWN + */ +static int +sa1100_verify_port(struct uart_port *port, struct serial_struct *ser) +{ + struct sa1100_port *sport = + container_of(port, struct sa1100_port, port); + int ret = 0; + + if (ser->type != PORT_UNKNOWN && ser->type != PORT_SA1100) + ret = -EINVAL; + if (sport->port.irq != ser->irq) + ret = -EINVAL; + if (ser->io_type != SERIAL_IO_MEM) + ret = -EINVAL; + if (sport->port.uartclk / 16 != ser->baud_base) + ret = -EINVAL; + if ((void *)sport->port.mapbase != ser->iomem_base) + ret = -EINVAL; + if (sport->port.iobase != ser->port) + ret = -EINVAL; + if (ser->hub6 != 0) + ret = -EINVAL; + return ret; +} + +static struct uart_ops sa1100_pops = { + .tx_empty = sa1100_tx_empty, + .set_mctrl = sa1100_set_mctrl, + .get_mctrl = sa1100_get_mctrl, + .stop_tx = sa1100_stop_tx, + .start_tx = sa1100_start_tx, + .stop_rx = sa1100_stop_rx, + .enable_ms = sa1100_enable_ms, + .break_ctl = sa1100_break_ctl, + .startup = sa1100_startup, + .shutdown = sa1100_shutdown, + .set_termios = sa1100_set_termios, + .type = sa1100_type, + .release_port = sa1100_release_port, + .request_port = sa1100_request_port, + .config_port = sa1100_config_port, + .verify_port = sa1100_verify_port, +}; + +static struct sa1100_port sa1100_ports[NR_PORTS]; + +/* + * Setup the SA1100 serial ports. Note that we don't include the IrDA + * port here since we have our own SIR/FIR driver (see drivers/net/irda) + * + * Note also that we support "console=ttySAx" where "x" is either 0 or 1. + * Which serial port this ends up being depends on the machine you're + * running this kernel on. I'm not convinced that this is a good idea, + * but that's the way it traditionally works. + * + * Note that NanoEngine UART3 becomes UART2, and UART2 is no longer + * used here. + */ +static void __init sa1100_init_ports(void) +{ + static int first = 1; + int i; + + if (!first) + return; + first = 0; + + for (i = 0; i < NR_PORTS; i++) { + sa1100_ports[i].port.uartclk = 3686400; + sa1100_ports[i].port.ops = &sa1100_pops; + sa1100_ports[i].port.fifosize = 8; + sa1100_ports[i].port.line = i; + sa1100_ports[i].port.iotype = UPIO_MEM; + timer_setup(&sa1100_ports[i].timer, sa1100_timeout, 0); + } + + /* + * make transmit lines outputs, so that when the port + * is closed, the output is in the MARK state. + */ + PPDR |= PPC_TXD1 | PPC_TXD3; + PPSR |= PPC_TXD1 | PPC_TXD3; +} + +void sa1100_register_uart_fns(struct sa1100_port_fns *fns) +{ + if (fns->get_mctrl) + sa1100_pops.get_mctrl = fns->get_mctrl; + if (fns->set_mctrl) + sa1100_pops.set_mctrl = fns->set_mctrl; + + sa1100_pops.pm = fns->pm; + /* + * FIXME: fns->set_wake is unused - this should be called from + * the suspend() callback if device_may_wakeup(dev)) is set. + */ +} + +void __init sa1100_register_uart(int idx, int port) +{ + if (idx >= NR_PORTS) { + printk(KERN_ERR "%s: bad index number %d\n", __func__, idx); + return; + } + + switch (port) { + case 1: + sa1100_ports[idx].port.membase = (void __iomem *)&Ser1UTCR0; + sa1100_ports[idx].port.mapbase = _Ser1UTCR0; + sa1100_ports[idx].port.irq = IRQ_Ser1UART; + sa1100_ports[idx].port.flags = UPF_BOOT_AUTOCONF; + break; + + case 2: + sa1100_ports[idx].port.membase = (void __iomem *)&Ser2UTCR0; + sa1100_ports[idx].port.mapbase = _Ser2UTCR0; + sa1100_ports[idx].port.irq = IRQ_Ser2ICP; + sa1100_ports[idx].port.flags = UPF_BOOT_AUTOCONF; + break; + + case 3: + sa1100_ports[idx].port.membase = (void __iomem *)&Ser3UTCR0; + sa1100_ports[idx].port.mapbase = _Ser3UTCR0; + sa1100_ports[idx].port.irq = IRQ_Ser3UART; + sa1100_ports[idx].port.flags = UPF_BOOT_AUTOCONF; + break; + + default: + printk(KERN_ERR "%s: bad port number %d\n", __func__, port); + } +} + + +#ifdef CONFIG_SERIAL_SA1100_CONSOLE +static void sa1100_console_putchar(struct uart_port *port, int ch) +{ + struct sa1100_port *sport = + container_of(port, struct sa1100_port, port); + + while (!(UART_GET_UTSR1(sport) & UTSR1_TNF)) + barrier(); + UART_PUT_CHAR(sport, ch); +} + +/* + * Interrupts are disabled on entering + */ +static void +sa1100_console_write(struct console *co, const char *s, unsigned int count) +{ + struct sa1100_port *sport = &sa1100_ports[co->index]; + unsigned int old_utcr3, status; + + /* + * First, save UTCR3 and then disable interrupts + */ + old_utcr3 = UART_GET_UTCR3(sport); + UART_PUT_UTCR3(sport, (old_utcr3 & ~(UTCR3_RIE | UTCR3_TIE)) | + UTCR3_TXE); + + uart_console_write(&sport->port, s, count, sa1100_console_putchar); + + /* + * Finally, wait for transmitter to become empty + * and restore UTCR3 + */ + do { + status = UART_GET_UTSR1(sport); + } while (status & UTSR1_TBY); + UART_PUT_UTCR3(sport, old_utcr3); +} + +/* + * If the port was already initialised (eg, by a boot loader), + * try to determine the current setup. + */ +static void __init +sa1100_console_get_options(struct sa1100_port *sport, int *baud, + int *parity, int *bits) +{ + unsigned int utcr3; + + utcr3 = UART_GET_UTCR3(sport) & (UTCR3_RXE | UTCR3_TXE); + if (utcr3 == (UTCR3_RXE | UTCR3_TXE)) { + /* ok, the port was enabled */ + unsigned int utcr0, quot; + + utcr0 = UART_GET_UTCR0(sport); + + *parity = 'n'; + if (utcr0 & UTCR0_PE) { + if (utcr0 & UTCR0_OES) + *parity = 'e'; + else + *parity = 'o'; + } + + if (utcr0 & UTCR0_DSS) + *bits = 8; + else + *bits = 7; + + quot = UART_GET_UTCR2(sport) | UART_GET_UTCR1(sport) << 8; + quot &= 0xfff; + *baud = sport->port.uartclk / (16 * (quot + 1)); + } +} + +static int __init +sa1100_console_setup(struct console *co, char *options) +{ + struct sa1100_port *sport; + int baud = 9600; + int bits = 8; + int parity = 'n'; + int flow = 'n'; + + /* + * Check whether an invalid uart number has been specified, and + * if so, search for the first available port that does have + * console support. + */ + if (co->index == -1 || co->index >= NR_PORTS) + co->index = 0; + sport = &sa1100_ports[co->index]; + + if (options) + uart_parse_options(options, &baud, &parity, &bits, &flow); + else + sa1100_console_get_options(sport, &baud, &parity, &bits); + + return uart_set_options(&sport->port, co, baud, parity, bits, flow); +} + +static struct uart_driver sa1100_reg; +static struct console sa1100_console = { + .name = "ttySA", + .write = sa1100_console_write, + .device = uart_console_device, + .setup = sa1100_console_setup, + .flags = CON_PRINTBUFFER, + .index = -1, + .data = &sa1100_reg, +}; + +static int __init sa1100_rs_console_init(void) +{ + sa1100_init_ports(); + register_console(&sa1100_console); + return 0; +} +console_initcall(sa1100_rs_console_init); + +#define SA1100_CONSOLE &sa1100_console +#else +#define SA1100_CONSOLE NULL +#endif + +static struct uart_driver sa1100_reg = { + .owner = THIS_MODULE, + .driver_name = "ttySA", + .dev_name = "ttySA", + .major = SERIAL_SA1100_MAJOR, + .minor = MINOR_START, + .nr = NR_PORTS, + .cons = SA1100_CONSOLE, +}; + +static int sa1100_serial_suspend(struct platform_device *dev, pm_message_t state) +{ + struct sa1100_port *sport = platform_get_drvdata(dev); + + if (sport) + uart_suspend_port(&sa1100_reg, &sport->port); + + return 0; +} + +static int sa1100_serial_resume(struct platform_device *dev) +{ + struct sa1100_port *sport = platform_get_drvdata(dev); + + if (sport) + uart_resume_port(&sa1100_reg, &sport->port); + + return 0; +} + +static int sa1100_serial_add_one_port(struct sa1100_port *sport, struct platform_device *dev) +{ + sport->port.dev = &dev->dev; + sport->port.has_sysrq = IS_ENABLED(CONFIG_SERIAL_SA1100_CONSOLE); + + // mctrl_gpio_init() requires that the GPIO driver supports interrupts, + // but we need to support GPIO drivers for hardware that has no such + // interrupts. Use mctrl_gpio_init_noauto() instead. + sport->gpios = mctrl_gpio_init_noauto(sport->port.dev, 0); + if (IS_ERR(sport->gpios)) { + int err = PTR_ERR(sport->gpios); + + dev_err(sport->port.dev, "failed to get mctrl gpios: %d\n", + err); + + if (err == -EPROBE_DEFER) + return err; + + sport->gpios = NULL; + } + + platform_set_drvdata(dev, sport); + + return uart_add_one_port(&sa1100_reg, &sport->port); +} + +static int sa1100_serial_probe(struct platform_device *dev) +{ + struct resource *res; + int i; + + res = platform_get_resource(dev, IORESOURCE_MEM, 0); + if (!res) + return -EINVAL; + + for (i = 0; i < NR_PORTS; i++) + if (sa1100_ports[i].port.mapbase == res->start) + break; + if (i == NR_PORTS) + return -ENODEV; + + sa1100_serial_add_one_port(&sa1100_ports[i], dev); + + return 0; +} + +static int sa1100_serial_remove(struct platform_device *pdev) +{ + struct sa1100_port *sport = platform_get_drvdata(pdev); + + if (sport) + uart_remove_one_port(&sa1100_reg, &sport->port); + + return 0; +} + +static struct platform_driver sa11x0_serial_driver = { + .probe = sa1100_serial_probe, + .remove = sa1100_serial_remove, + .suspend = sa1100_serial_suspend, + .resume = sa1100_serial_resume, + .driver = { + .name = "sa11x0-uart", + }, +}; + +static int __init sa1100_serial_init(void) +{ + int ret; + + printk(KERN_INFO "Serial: SA11x0 driver\n"); + + sa1100_init_ports(); + + ret = uart_register_driver(&sa1100_reg); + if (ret == 0) { + ret = platform_driver_register(&sa11x0_serial_driver); + if (ret) + uart_unregister_driver(&sa1100_reg); + } + return ret; +} + +static void __exit sa1100_serial_exit(void) +{ + platform_driver_unregister(&sa11x0_serial_driver); + uart_unregister_driver(&sa1100_reg); +} + +module_init(sa1100_serial_init); +module_exit(sa1100_serial_exit); + +MODULE_AUTHOR("Deep Blue Solutions Ltd"); +MODULE_DESCRIPTION("SA1100 generic serial port driver"); +MODULE_LICENSE("GPL"); +MODULE_ALIAS_CHARDEV_MAJOR(SERIAL_SA1100_MAJOR); +MODULE_ALIAS("platform:sa11x0-uart"); |