diff options
Diffstat (limited to '')
| -rw-r--r-- | include/linux/mfd/max8997.h | 210 |
1 files changed, 210 insertions, 0 deletions
diff --git a/include/linux/mfd/max8997.h b/include/linux/mfd/max8997.h new file mode 100644 index 000000000..e955e2f0a --- /dev/null +++ b/include/linux/mfd/max8997.h @@ -0,0 +1,210 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * max8997.h - Driver for the Maxim 8997/8966 + * + * Copyright (C) 2009-2010 Samsung Electrnoics + * MyungJoo Ham <myungjoo.ham@samsung.com> + * + * This driver is based on max8998.h + * + * MAX8997 has PMIC, MUIC, HAPTIC, RTC, FLASH, and Fuel Gauge devices. + * Except Fuel Gauge, every device shares the same I2C bus and included in + * this mfd driver. Although the fuel gauge is included in the chip, it is + * excluded from the driver because a) it has a different I2C bus from + * others and b) it can be enabled simply by using MAX17042 driver. + */ + +#ifndef __LINUX_MFD_MAX8998_H +#define __LINUX_MFD_MAX8998_H + +#include <linux/regulator/consumer.h> + +/* MAX8997/8966 regulator IDs */ +enum max8998_regulators { + MAX8997_LDO1 = 0, + MAX8997_LDO2, + MAX8997_LDO3, + MAX8997_LDO4, + MAX8997_LDO5, + MAX8997_LDO6, + MAX8997_LDO7, + MAX8997_LDO8, + MAX8997_LDO9, + MAX8997_LDO10, + MAX8997_LDO11, + MAX8997_LDO12, + MAX8997_LDO13, + MAX8997_LDO14, + MAX8997_LDO15, + MAX8997_LDO16, + MAX8997_LDO17, + MAX8997_LDO18, + MAX8997_LDO21, + MAX8997_BUCK1, + MAX8997_BUCK2, + MAX8997_BUCK3, + MAX8997_BUCK4, + MAX8997_BUCK5, + MAX8997_BUCK6, + MAX8997_BUCK7, + MAX8997_EN32KHZ_AP, + MAX8997_EN32KHZ_CP, + MAX8997_ENVICHG, + MAX8997_ESAFEOUT1, + MAX8997_ESAFEOUT2, + MAX8997_CHARGER_CV, /* control MBCCV of MBCCTRL3 */ + MAX8997_CHARGER, /* charger current, MBCCTRL4 */ + MAX8997_CHARGER_TOPOFF, /* MBCCTRL5 */ + + MAX8997_REG_MAX, +}; + +struct max8997_regulator_data { + int id; + struct regulator_init_data *initdata; + struct device_node *reg_node; +}; + +struct max8997_muic_reg_data { + u8 addr; + u8 data; +}; + +/** + * struct max8997_muic_platform_data + * @init_data: array of max8997_muic_reg_data + * used for initializing registers of MAX8997 MUIC device + * @num_init_data: array size of init_data + */ +struct max8997_muic_platform_data { + struct max8997_muic_reg_data *init_data; + int num_init_data; + + /* Check cable state after certain delay */ + int detcable_delay_ms; + + /* + * Default usb/uart path whether UART/USB or AUX_UART/AUX_USB + * h/w path of COMP2/COMN1 on CONTROL1 register. + */ + int path_usb; + int path_uart; +}; + +enum max8997_haptic_motor_type { + MAX8997_HAPTIC_ERM, + MAX8997_HAPTIC_LRA, +}; + +enum max8997_haptic_pulse_mode { + MAX8997_EXTERNAL_MODE, + MAX8997_INTERNAL_MODE, +}; + +enum max8997_haptic_pwm_divisor { + MAX8997_PWM_DIVISOR_32, + MAX8997_PWM_DIVISOR_64, + MAX8997_PWM_DIVISOR_128, + MAX8997_PWM_DIVISOR_256, +}; + +/** + * max8997_haptic_platform_data + * @pwm_channel_id: channel number of PWM device + * valid for MAX8997_EXTERNAL_MODE + * @pwm_period: period in nano second for PWM device + * valid for MAX8997_EXTERNAL_MODE + * @type: motor type + * @mode: pulse mode + * MAX8997_EXTERNAL_MODE: external PWM device is used to control motor + * MAX8997_INTERNAL_MODE: internal pulse generator is used to control motor + * @pwm_divisor: divisor for external PWM device + * @internal_mode_pattern: internal mode pattern for internal mode + * [0 - 3]: valid pattern number + * @pattern_cycle: the number of cycles of the waveform + * for the internal mode pattern + * [0 - 15]: available cycles + * @pattern_signal_period: period of the waveform for the internal mode pattern + * [0 - 255]: available period + */ +struct max8997_haptic_platform_data { + unsigned int pwm_channel_id; + unsigned int pwm_period; + + enum max8997_haptic_motor_type type; + enum max8997_haptic_pulse_mode mode; + enum max8997_haptic_pwm_divisor pwm_divisor; + + unsigned int internal_mode_pattern; + unsigned int pattern_cycle; + unsigned int pattern_signal_period; +}; + +enum max8997_led_mode { + MAX8997_NONE, + MAX8997_FLASH_MODE, + MAX8997_MOVIE_MODE, + MAX8997_FLASH_PIN_CONTROL_MODE, + MAX8997_MOVIE_PIN_CONTROL_MODE, +}; + +/** + * struct max8997_led_platform_data + * The number of LED devices for MAX8997 is two + * @mode: LED mode for each LED device + * @brightness: initial brightness for each LED device + * range: + * [0 - 31]: MAX8997_FLASH_MODE and MAX8997_FLASH_PIN_CONTROL_MODE + * [0 - 15]: MAX8997_MOVIE_MODE and MAX8997_MOVIE_PIN_CONTROL_MODE + */ +struct max8997_led_platform_data { + enum max8997_led_mode mode[2]; + u8 brightness[2]; +}; + +struct max8997_platform_data { + /* IRQ */ + int ono; + + /* ---- PMIC ---- */ + struct max8997_regulator_data *regulators; + int num_regulators; + + /* + * SET1~3 DVS GPIOs control Buck1, 2, and 5 simultaneously. Therefore, + * With buckx_gpiodvs enabled, the buckx cannot be controlled + * independently. To control buckx (of 1, 2, and 5) independently, + * disable buckx_gpiodvs and control with BUCKxDVS1 register. + * + * When buckx_gpiodvs and bucky_gpiodvs are both enabled, set_voltage + * on buckx will change the voltage of bucky at the same time. + * + */ + bool ignore_gpiodvs_side_effect; + int buck125_gpios[3]; /* GPIO of [0]SET1, [1]SET2, [2]SET3 */ + int buck125_default_idx; /* Default value of SET1, 2, 3 */ + unsigned int buck1_voltage[8]; /* buckx_voltage in uV */ + bool buck1_gpiodvs; + unsigned int buck2_voltage[8]; + bool buck2_gpiodvs; + unsigned int buck5_voltage[8]; + bool buck5_gpiodvs; + + /* ---- Charger control ---- */ + /* eoc stands for 'end of charge' */ + int eoc_mA; /* 50 ~ 200mA by 10mA step */ + /* charge Full Timeout */ + int timeout; /* 0 (no timeout), 5, 6, 7 hours */ + + /* ---- MUIC ---- */ + struct max8997_muic_platform_data *muic_pdata; + + /* ---- HAPTIC ---- */ + struct max8997_haptic_platform_data *haptic_pdata; + + /* RTC: Not implemented */ + /* ---- LED ---- */ + struct max8997_led_platform_data *led_pdata; +}; + +#endif /* __LINUX_MFD_MAX8998_H */ |