summaryrefslogtreecommitdiffstats
path: root/include/sound/sof/dai-intel.h
diff options
context:
space:
mode:
Diffstat (limited to 'include/sound/sof/dai-intel.h')
-rw-r--r--include/sound/sof/dai-intel.h199
1 files changed, 199 insertions, 0 deletions
diff --git a/include/sound/sof/dai-intel.h b/include/sound/sof/dai-intel.h
new file mode 100644
index 000000000..136adf668
--- /dev/null
+++ b/include/sound/sof/dai-intel.h
@@ -0,0 +1,199 @@
+/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-3-Clause) */
+/*
+ * This file is provided under a dual BSD/GPLv2 license. When using or
+ * redistributing this file, you may do so under either license.
+ *
+ * Copyright(c) 2018 Intel Corporation. All rights reserved.
+ */
+
+#ifndef __INCLUDE_SOUND_SOF_DAI_INTEL_H__
+#define __INCLUDE_SOUND_SOF_DAI_INTEL_H__
+
+#include <sound/sof/header.h>
+
+ /* ssc1: TINTE */
+#define SOF_DAI_INTEL_SSP_QUIRK_TINTE (1 << 0)
+ /* ssc1: PINTE */
+#define SOF_DAI_INTEL_SSP_QUIRK_PINTE (1 << 1)
+ /* ssc2: SMTATF */
+#define SOF_DAI_INTEL_SSP_QUIRK_SMTATF (1 << 2)
+ /* ssc2: MMRATF */
+#define SOF_DAI_INTEL_SSP_QUIRK_MMRATF (1 << 3)
+ /* ssc2: PSPSTWFDFD */
+#define SOF_DAI_INTEL_SSP_QUIRK_PSPSTWFDFD (1 << 4)
+ /* ssc2: PSPSRWFDFD */
+#define SOF_DAI_INTEL_SSP_QUIRK_PSPSRWFDFD (1 << 5)
+/* ssc1: LBM */
+#define SOF_DAI_INTEL_SSP_QUIRK_LBM (1 << 6)
+
+ /* here is the possibility to define others aux macros */
+
+#define SOF_DAI_INTEL_SSP_FRAME_PULSE_WIDTH_MAX 38
+#define SOF_DAI_INTEL_SSP_SLOT_PADDING_MAX 31
+
+/* SSP clocks control settings
+ *
+ * Macros for clks_control field in sof_ipc_dai_ssp_params struct.
+ */
+
+/* mclk 0 disable */
+#define SOF_DAI_INTEL_SSP_MCLK_0_DISABLE BIT(0)
+/* mclk 1 disable */
+#define SOF_DAI_INTEL_SSP_MCLK_1_DISABLE BIT(1)
+/* mclk keep active */
+#define SOF_DAI_INTEL_SSP_CLKCTRL_MCLK_KA BIT(2)
+/* bclk keep active */
+#define SOF_DAI_INTEL_SSP_CLKCTRL_BCLK_KA BIT(3)
+/* fs keep active */
+#define SOF_DAI_INTEL_SSP_CLKCTRL_FS_KA BIT(4)
+/* bclk idle */
+#define SOF_DAI_INTEL_SSP_CLKCTRL_BCLK_IDLE_HIGH BIT(5)
+
+/* DMIC max. four controllers for eight microphone channels */
+#define SOF_DAI_INTEL_DMIC_NUM_CTRL 4
+
+/* SSP Configuration Request - SOF_IPC_DAI_SSP_CONFIG */
+struct sof_ipc_dai_ssp_params {
+ struct sof_ipc_hdr hdr;
+ uint16_t reserved1;
+ uint16_t mclk_id;
+
+ uint32_t mclk_rate; /* mclk frequency in Hz */
+ uint32_t fsync_rate; /* fsync frequency in Hz */
+ uint32_t bclk_rate; /* bclk frequency in Hz */
+
+ /* TDM */
+ uint32_t tdm_slots;
+ uint32_t rx_slots;
+ uint32_t tx_slots;
+
+ /* data */
+ uint32_t sample_valid_bits;
+ uint16_t tdm_slot_width;
+ uint16_t reserved2; /* alignment */
+
+ /* MCLK */
+ uint32_t mclk_direction;
+
+ uint16_t frame_pulse_width;
+ uint16_t tdm_per_slot_padding_flag;
+ uint32_t clks_control;
+ uint32_t quirks;
+ uint32_t bclk_delay; /* guaranteed time (ms) for which BCLK
+ * will be driven, before sending data
+ */
+} __packed;
+
+/* HDA Configuration Request - SOF_IPC_DAI_HDA_CONFIG */
+struct sof_ipc_dai_hda_params {
+ struct sof_ipc_hdr hdr;
+ uint32_t link_dma_ch;
+ uint32_t rate;
+ uint32_t channels;
+} __packed;
+
+/* ALH Configuration Request - SOF_IPC_DAI_ALH_CONFIG */
+struct sof_ipc_dai_alh_params {
+ struct sof_ipc_hdr hdr;
+ uint32_t stream_id;
+ uint32_t rate;
+ uint32_t channels;
+
+ /* reserved for future use */
+ uint32_t reserved[13];
+} __packed;
+
+/* DMIC Configuration Request - SOF_IPC_DAI_DMIC_CONFIG */
+
+/* This struct is defined per 2ch PDM controller available in the platform.
+ * Normally it is sufficient to set the used microphone specific enables to 1
+ * and keep other parameters as zero. The customizations are:
+ *
+ * 1. If a device mixes different microphones types with different polarity
+ * and/or the absolute polarity matters the PCM signal from a microphone
+ * can be inverted with the controls.
+ *
+ * 2. If the microphones in a stereo pair do not appear in captured stream
+ * in desired order due to board schematics choises they can be swapped with
+ * the clk_edge parameter.
+ *
+ * 3. If PDM bit errors are seen in capture (poor quality) the skew parameter
+ * that delays the sampling time of data by half cycles of DMIC source clock
+ * can be tried for improvement. However there is no guarantee for this to fix
+ * data integrity problems.
+ */
+struct sof_ipc_dai_dmic_pdm_ctrl {
+ struct sof_ipc_hdr hdr;
+ uint16_t id; /**< PDM controller ID */
+
+ uint16_t enable_mic_a; /**< Use A (left) channel mic (0 or 1)*/
+ uint16_t enable_mic_b; /**< Use B (right) channel mic (0 or 1)*/
+
+ uint16_t polarity_mic_a; /**< Optionally invert mic A signal (0 or 1) */
+ uint16_t polarity_mic_b; /**< Optionally invert mic B signal (0 or 1) */
+
+ uint16_t clk_edge; /**< Optionally swap data clock edge (0 or 1) */
+ uint16_t skew; /**< Adjust PDM data sampling vs. clock (0..15) */
+
+ uint16_t reserved[3]; /**< Make sure the total size is 4 bytes aligned */
+} __packed;
+
+/* This struct contains the global settings for all 2ch PDM controllers. The
+ * version number used in configuration data is checked vs. version used by
+ * device driver src/drivers/dmic.c need to match. It is incremented from
+ * initial value 1 if updates done for the to driver would alter the operation
+ * of the microphone.
+ *
+ * Note: The microphone clock (pdmclk_min, pdmclk_max, duty_min, duty_max)
+ * parameters need to be set as defined in microphone data sheet. E.g. clock
+ * range 1.0 - 3.2 MHz is usually supported microphones. Some microphones are
+ * multi-mode capable and there may be denied mic clock frequencies between
+ * the modes. In such case set the clock range limits of the desired mode to
+ * avoid the driver to set clock to an illegal rate.
+ *
+ * The duty cycle could be set to 48-52% if not known. Generally these
+ * parameters can be altered within data sheet specified limits to match
+ * required audio application performance power.
+ *
+ * The microphone clock needs to be usually about 50-80 times the used audio
+ * sample rate. With highest sample rates above 48 kHz this can relaxed
+ * somewhat.
+ *
+ * The parameter wake_up_time describes how long time the microphone needs
+ * for the data line to produce valid output from mic clock start. The driver
+ * will mute the captured audio for the given time. The min_clock_on_time
+ * parameter is used to prevent too short clock bursts to happen. The driver
+ * will keep the clock active after capture stop if this time is not yet
+ * met. The unit for both is microseconds (us). Exceed of 100 ms will be
+ * treated as an error.
+ */
+struct sof_ipc_dai_dmic_params {
+ struct sof_ipc_hdr hdr;
+ uint32_t driver_ipc_version; /**< Version (1..N) */
+
+ uint32_t pdmclk_min; /**< Minimum microphone clock in Hz (100000..N) */
+ uint32_t pdmclk_max; /**< Maximum microphone clock in Hz (min...N) */
+
+ uint32_t fifo_fs; /**< FIFO sample rate in Hz (8000..96000) */
+ uint32_t reserved_1; /**< Reserved */
+ uint16_t fifo_bits; /**< FIFO word length (16 or 32) */
+ uint16_t fifo_bits_b; /**< Deprecated since firmware ABI 3.0.1 */
+
+ uint16_t duty_min; /**< Min. mic clock duty cycle in % (20..80) */
+ uint16_t duty_max; /**< Max. mic clock duty cycle in % (min..80) */
+
+ uint32_t num_pdm_active; /**< Number of active pdm controllers. */
+ /**< Range is 1..SOF_DAI_INTEL_DMIC_NUM_CTRL */
+
+ uint32_t wake_up_time; /**< Time from clock start to data (us) */
+ uint32_t min_clock_on_time; /**< Min. time that clk is kept on (us) */
+ uint32_t unmute_ramp_time; /**< Length of logarithmic gain ramp (ms) */
+
+ /* reserved for future use */
+ uint32_t reserved[5];
+
+ /**< PDM controllers configuration */
+ struct sof_ipc_dai_dmic_pdm_ctrl pdm[SOF_DAI_INTEL_DMIC_NUM_CTRL];
+} __packed;
+
+#endif