diff options
Diffstat (limited to '')
-rw-r--r-- | sound/soc/ux500/ux500_msp_i2s.c | 731 |
1 files changed, 731 insertions, 0 deletions
diff --git a/sound/soc/ux500/ux500_msp_i2s.c b/sound/soc/ux500/ux500_msp_i2s.c new file mode 100644 index 000000000..fd0b88bb7 --- /dev/null +++ b/sound/soc/ux500/ux500_msp_i2s.c @@ -0,0 +1,731 @@ +// SPDX-License-Identifier: GPL-2.0-only +/* + * Copyright (C) ST-Ericsson SA 2012 + * + * Author: Ola Lilja <ola.o.lilja@stericsson.com>, + * Roger Nilsson <roger.xr.nilsson@stericsson.com>, + * Sandeep Kaushik <sandeep.kaushik@st.com> + * for ST-Ericsson. + * + * License terms: + */ + +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/delay.h> +#include <linux/slab.h> +#include <linux/io.h> +#include <linux/of.h> +#include <linux/platform_data/asoc-ux500-msp.h> + +#include <sound/soc.h> + +#include "ux500_msp_i2s.h" + + /* Protocol desciptors */ +static const struct msp_protdesc prot_descs[] = { + { /* I2S */ + MSP_SINGLE_PHASE, + MSP_SINGLE_PHASE, + MSP_PHASE2_START_MODE_IMEDIATE, + MSP_PHASE2_START_MODE_IMEDIATE, + MSP_BTF_MS_BIT_FIRST, + MSP_BTF_MS_BIT_FIRST, + MSP_FRAME_LEN_1, + MSP_FRAME_LEN_1, + MSP_FRAME_LEN_1, + MSP_FRAME_LEN_1, + MSP_ELEM_LEN_32, + MSP_ELEM_LEN_32, + MSP_ELEM_LEN_32, + MSP_ELEM_LEN_32, + MSP_DELAY_1, + MSP_DELAY_1, + MSP_RISING_EDGE, + MSP_FALLING_EDGE, + MSP_FSYNC_POL_ACT_LO, + MSP_FSYNC_POL_ACT_LO, + MSP_SWAP_NONE, + MSP_SWAP_NONE, + MSP_COMPRESS_MODE_LINEAR, + MSP_EXPAND_MODE_LINEAR, + MSP_FSYNC_IGNORE, + 31, + 15, + 32, + }, { /* PCM */ + MSP_DUAL_PHASE, + MSP_DUAL_PHASE, + MSP_PHASE2_START_MODE_FSYNC, + MSP_PHASE2_START_MODE_FSYNC, + MSP_BTF_MS_BIT_FIRST, + MSP_BTF_MS_BIT_FIRST, + MSP_FRAME_LEN_1, + MSP_FRAME_LEN_1, + MSP_FRAME_LEN_1, + MSP_FRAME_LEN_1, + MSP_ELEM_LEN_16, + MSP_ELEM_LEN_16, + MSP_ELEM_LEN_16, + MSP_ELEM_LEN_16, + MSP_DELAY_0, + MSP_DELAY_0, + MSP_RISING_EDGE, + MSP_FALLING_EDGE, + MSP_FSYNC_POL_ACT_HI, + MSP_FSYNC_POL_ACT_HI, + MSP_SWAP_NONE, + MSP_SWAP_NONE, + MSP_COMPRESS_MODE_LINEAR, + MSP_EXPAND_MODE_LINEAR, + MSP_FSYNC_IGNORE, + 255, + 0, + 256, + }, { /* Companded PCM */ + MSP_SINGLE_PHASE, + MSP_SINGLE_PHASE, + MSP_PHASE2_START_MODE_FSYNC, + MSP_PHASE2_START_MODE_FSYNC, + MSP_BTF_MS_BIT_FIRST, + MSP_BTF_MS_BIT_FIRST, + MSP_FRAME_LEN_1, + MSP_FRAME_LEN_1, + MSP_FRAME_LEN_1, + MSP_FRAME_LEN_1, + MSP_ELEM_LEN_8, + MSP_ELEM_LEN_8, + MSP_ELEM_LEN_8, + MSP_ELEM_LEN_8, + MSP_DELAY_0, + MSP_DELAY_0, + MSP_RISING_EDGE, + MSP_RISING_EDGE, + MSP_FSYNC_POL_ACT_HI, + MSP_FSYNC_POL_ACT_HI, + MSP_SWAP_NONE, + MSP_SWAP_NONE, + MSP_COMPRESS_MODE_LINEAR, + MSP_EXPAND_MODE_LINEAR, + MSP_FSYNC_IGNORE, + 255, + 0, + 256, + }, +}; + +static void set_prot_desc_tx(struct ux500_msp *msp, + struct msp_protdesc *protdesc, + enum msp_data_size data_size) +{ + u32 temp_reg = 0; + + temp_reg |= MSP_P2_ENABLE_BIT(protdesc->tx_phase_mode); + temp_reg |= MSP_P2_START_MODE_BIT(protdesc->tx_phase2_start_mode); + temp_reg |= MSP_P1_FRAME_LEN_BITS(protdesc->tx_frame_len_1); + temp_reg |= MSP_P2_FRAME_LEN_BITS(protdesc->tx_frame_len_2); + if (msp->def_elem_len) { + temp_reg |= MSP_P1_ELEM_LEN_BITS(protdesc->tx_elem_len_1); + temp_reg |= MSP_P2_ELEM_LEN_BITS(protdesc->tx_elem_len_2); + } else { + temp_reg |= MSP_P1_ELEM_LEN_BITS(data_size); + temp_reg |= MSP_P2_ELEM_LEN_BITS(data_size); + } + temp_reg |= MSP_DATA_DELAY_BITS(protdesc->tx_data_delay); + temp_reg |= MSP_SET_ENDIANNES_BIT(protdesc->tx_byte_order); + temp_reg |= MSP_FSYNC_POL(protdesc->tx_fsync_pol); + temp_reg |= MSP_DATA_WORD_SWAP(protdesc->tx_half_word_swap); + temp_reg |= MSP_SET_COMPANDING_MODE(protdesc->compression_mode); + temp_reg |= MSP_SET_FSYNC_IGNORE(protdesc->frame_sync_ignore); + + writel(temp_reg, msp->registers + MSP_TCF); +} + +static void set_prot_desc_rx(struct ux500_msp *msp, + struct msp_protdesc *protdesc, + enum msp_data_size data_size) +{ + u32 temp_reg = 0; + + temp_reg |= MSP_P2_ENABLE_BIT(protdesc->rx_phase_mode); + temp_reg |= MSP_P2_START_MODE_BIT(protdesc->rx_phase2_start_mode); + temp_reg |= MSP_P1_FRAME_LEN_BITS(protdesc->rx_frame_len_1); + temp_reg |= MSP_P2_FRAME_LEN_BITS(protdesc->rx_frame_len_2); + if (msp->def_elem_len) { + temp_reg |= MSP_P1_ELEM_LEN_BITS(protdesc->rx_elem_len_1); + temp_reg |= MSP_P2_ELEM_LEN_BITS(protdesc->rx_elem_len_2); + } else { + temp_reg |= MSP_P1_ELEM_LEN_BITS(data_size); + temp_reg |= MSP_P2_ELEM_LEN_BITS(data_size); + } + + temp_reg |= MSP_DATA_DELAY_BITS(protdesc->rx_data_delay); + temp_reg |= MSP_SET_ENDIANNES_BIT(protdesc->rx_byte_order); + temp_reg |= MSP_FSYNC_POL(protdesc->rx_fsync_pol); + temp_reg |= MSP_DATA_WORD_SWAP(protdesc->rx_half_word_swap); + temp_reg |= MSP_SET_COMPANDING_MODE(protdesc->expansion_mode); + temp_reg |= MSP_SET_FSYNC_IGNORE(protdesc->frame_sync_ignore); + + writel(temp_reg, msp->registers + MSP_RCF); +} + +static int configure_protocol(struct ux500_msp *msp, + struct ux500_msp_config *config) +{ + struct msp_protdesc *protdesc; + enum msp_data_size data_size; + u32 temp_reg = 0; + + data_size = config->data_size; + msp->def_elem_len = config->def_elem_len; + if (config->default_protdesc == 1) { + if (config->protocol >= MSP_INVALID_PROTOCOL) { + dev_err(msp->dev, "%s: ERROR: Invalid protocol!\n", + __func__); + return -EINVAL; + } + protdesc = + (struct msp_protdesc *)&prot_descs[config->protocol]; + } else { + protdesc = (struct msp_protdesc *)&config->protdesc; + } + + if (data_size < MSP_DATA_BITS_DEFAULT || data_size > MSP_DATA_BITS_32) { + dev_err(msp->dev, + "%s: ERROR: Invalid data-size requested (data_size = %d)!\n", + __func__, data_size); + return -EINVAL; + } + + if (config->direction & MSP_DIR_TX) + set_prot_desc_tx(msp, protdesc, data_size); + if (config->direction & MSP_DIR_RX) + set_prot_desc_rx(msp, protdesc, data_size); + + /* The code below should not be separated. */ + temp_reg = readl(msp->registers + MSP_GCR) & ~TX_CLK_POL_RISING; + temp_reg |= MSP_TX_CLKPOL_BIT(~protdesc->tx_clk_pol); + writel(temp_reg, msp->registers + MSP_GCR); + temp_reg = readl(msp->registers + MSP_GCR) & ~RX_CLK_POL_RISING; + temp_reg |= MSP_RX_CLKPOL_BIT(protdesc->rx_clk_pol); + writel(temp_reg, msp->registers + MSP_GCR); + + return 0; +} + +static int setup_bitclk(struct ux500_msp *msp, struct ux500_msp_config *config) +{ + u32 reg_val_GCR; + u32 frame_per = 0; + u32 sck_div = 0; + u32 frame_width = 0; + u32 temp_reg = 0; + struct msp_protdesc *protdesc = NULL; + + reg_val_GCR = readl(msp->registers + MSP_GCR); + writel(reg_val_GCR & ~SRG_ENABLE, msp->registers + MSP_GCR); + + if (config->default_protdesc) + protdesc = + (struct msp_protdesc *)&prot_descs[config->protocol]; + else + protdesc = (struct msp_protdesc *)&config->protdesc; + + switch (config->protocol) { + case MSP_PCM_PROTOCOL: + case MSP_PCM_COMPAND_PROTOCOL: + frame_width = protdesc->frame_width; + sck_div = config->f_inputclk / (config->frame_freq * + (protdesc->clocks_per_frame)); + frame_per = protdesc->frame_period; + break; + case MSP_I2S_PROTOCOL: + frame_width = protdesc->frame_width; + sck_div = config->f_inputclk / (config->frame_freq * + (protdesc->clocks_per_frame)); + frame_per = protdesc->frame_period; + break; + default: + dev_err(msp->dev, "%s: ERROR: Unknown protocol (%d)!\n", + __func__, + config->protocol); + return -EINVAL; + } + + temp_reg = (sck_div - 1) & SCK_DIV_MASK; + temp_reg |= FRAME_WIDTH_BITS(frame_width); + temp_reg |= FRAME_PERIOD_BITS(frame_per); + writel(temp_reg, msp->registers + MSP_SRG); + + msp->f_bitclk = (config->f_inputclk)/(sck_div + 1); + + /* Enable bit-clock */ + udelay(100); + reg_val_GCR = readl(msp->registers + MSP_GCR); + writel(reg_val_GCR | SRG_ENABLE, msp->registers + MSP_GCR); + udelay(100); + + return 0; +} + +static int configure_multichannel(struct ux500_msp *msp, + struct ux500_msp_config *config) +{ + struct msp_protdesc *protdesc; + struct msp_multichannel_config *mcfg; + u32 reg_val_MCR; + + if (config->default_protdesc == 1) { + if (config->protocol >= MSP_INVALID_PROTOCOL) { + dev_err(msp->dev, + "%s: ERROR: Invalid protocol (%d)!\n", + __func__, config->protocol); + return -EINVAL; + } + protdesc = (struct msp_protdesc *) + &prot_descs[config->protocol]; + } else { + protdesc = (struct msp_protdesc *)&config->protdesc; + } + + mcfg = &config->multichannel_config; + if (mcfg->tx_multichannel_enable) { + if (protdesc->tx_phase_mode == MSP_SINGLE_PHASE) { + reg_val_MCR = readl(msp->registers + MSP_MCR); + writel(reg_val_MCR | (mcfg->tx_multichannel_enable ? + 1 << TMCEN_BIT : 0), + msp->registers + MSP_MCR); + writel(mcfg->tx_channel_0_enable, + msp->registers + MSP_TCE0); + writel(mcfg->tx_channel_1_enable, + msp->registers + MSP_TCE1); + writel(mcfg->tx_channel_2_enable, + msp->registers + MSP_TCE2); + writel(mcfg->tx_channel_3_enable, + msp->registers + MSP_TCE3); + } else { + dev_err(msp->dev, + "%s: ERROR: Only single-phase supported (TX-mode: %d)!\n", + __func__, protdesc->tx_phase_mode); + return -EINVAL; + } + } + if (mcfg->rx_multichannel_enable) { + if (protdesc->rx_phase_mode == MSP_SINGLE_PHASE) { + reg_val_MCR = readl(msp->registers + MSP_MCR); + writel(reg_val_MCR | (mcfg->rx_multichannel_enable ? + 1 << RMCEN_BIT : 0), + msp->registers + MSP_MCR); + writel(mcfg->rx_channel_0_enable, + msp->registers + MSP_RCE0); + writel(mcfg->rx_channel_1_enable, + msp->registers + MSP_RCE1); + writel(mcfg->rx_channel_2_enable, + msp->registers + MSP_RCE2); + writel(mcfg->rx_channel_3_enable, + msp->registers + MSP_RCE3); + } else { + dev_err(msp->dev, + "%s: ERROR: Only single-phase supported (RX-mode: %d)!\n", + __func__, protdesc->rx_phase_mode); + return -EINVAL; + } + if (mcfg->rx_comparison_enable_mode) { + reg_val_MCR = readl(msp->registers + MSP_MCR); + writel(reg_val_MCR | + (mcfg->rx_comparison_enable_mode << RCMPM_BIT), + msp->registers + MSP_MCR); + + writel(mcfg->comparison_mask, + msp->registers + MSP_RCM); + writel(mcfg->comparison_value, + msp->registers + MSP_RCV); + + } + } + + return 0; +} + +static int enable_msp(struct ux500_msp *msp, struct ux500_msp_config *config) +{ + int status = 0; + u32 reg_val_DMACR, reg_val_GCR; + + /* Configure msp with protocol dependent settings */ + configure_protocol(msp, config); + setup_bitclk(msp, config); + if (config->multichannel_configured == 1) { + status = configure_multichannel(msp, config); + if (status) + dev_warn(msp->dev, + "%s: WARN: configure_multichannel failed (%d)!\n", + __func__, status); + } + + /* Make sure the correct DMA-directions are configured */ + if ((config->direction & MSP_DIR_RX) && + !msp->capture_dma_data.dma_cfg) { + dev_err(msp->dev, "%s: ERROR: MSP RX-mode is not configured!", + __func__); + return -EINVAL; + } + if ((config->direction == MSP_DIR_TX) && + !msp->playback_dma_data.dma_cfg) { + dev_err(msp->dev, "%s: ERROR: MSP TX-mode is not configured!", + __func__); + return -EINVAL; + } + + reg_val_DMACR = readl(msp->registers + MSP_DMACR); + if (config->direction & MSP_DIR_RX) + reg_val_DMACR |= RX_DMA_ENABLE; + if (config->direction & MSP_DIR_TX) + reg_val_DMACR |= TX_DMA_ENABLE; + writel(reg_val_DMACR, msp->registers + MSP_DMACR); + + writel(config->iodelay, msp->registers + MSP_IODLY); + + /* Enable frame generation logic */ + reg_val_GCR = readl(msp->registers + MSP_GCR); + writel(reg_val_GCR | FRAME_GEN_ENABLE, msp->registers + MSP_GCR); + + return status; +} + +static void flush_fifo_rx(struct ux500_msp *msp) +{ + u32 reg_val_GCR, reg_val_FLR; + u32 limit = 32; + + reg_val_GCR = readl(msp->registers + MSP_GCR); + writel(reg_val_GCR | RX_ENABLE, msp->registers + MSP_GCR); + + reg_val_FLR = readl(msp->registers + MSP_FLR); + while (!(reg_val_FLR & RX_FIFO_EMPTY) && limit--) { + readl(msp->registers + MSP_DR); + reg_val_FLR = readl(msp->registers + MSP_FLR); + } + + writel(reg_val_GCR, msp->registers + MSP_GCR); +} + +static void flush_fifo_tx(struct ux500_msp *msp) +{ + u32 reg_val_GCR, reg_val_FLR; + u32 limit = 32; + + reg_val_GCR = readl(msp->registers + MSP_GCR); + writel(reg_val_GCR | TX_ENABLE, msp->registers + MSP_GCR); + writel(MSP_ITCR_ITEN | MSP_ITCR_TESTFIFO, msp->registers + MSP_ITCR); + + reg_val_FLR = readl(msp->registers + MSP_FLR); + while (!(reg_val_FLR & TX_FIFO_EMPTY) && limit--) { + readl(msp->registers + MSP_TSTDR); + reg_val_FLR = readl(msp->registers + MSP_FLR); + } + writel(0x0, msp->registers + MSP_ITCR); + writel(reg_val_GCR, msp->registers + MSP_GCR); +} + +int ux500_msp_i2s_open(struct ux500_msp *msp, + struct ux500_msp_config *config) +{ + u32 old_reg, new_reg, mask; + int res; + unsigned int tx_sel, rx_sel, tx_busy, rx_busy; + + if (in_interrupt()) { + dev_err(msp->dev, + "%s: ERROR: Open called in interrupt context!\n", + __func__); + return -1; + } + + tx_sel = (config->direction & MSP_DIR_TX) > 0; + rx_sel = (config->direction & MSP_DIR_RX) > 0; + if (!tx_sel && !rx_sel) { + dev_err(msp->dev, "%s: Error: No direction selected!\n", + __func__); + return -EINVAL; + } + + tx_busy = (msp->dir_busy & MSP_DIR_TX) > 0; + rx_busy = (msp->dir_busy & MSP_DIR_RX) > 0; + if (tx_busy && tx_sel) { + dev_err(msp->dev, "%s: Error: TX is in use!\n", __func__); + return -EBUSY; + } + if (rx_busy && rx_sel) { + dev_err(msp->dev, "%s: Error: RX is in use!\n", __func__); + return -EBUSY; + } + + msp->dir_busy |= (tx_sel ? MSP_DIR_TX : 0) | (rx_sel ? MSP_DIR_RX : 0); + + /* First do the global config register */ + mask = RX_CLK_SEL_MASK | TX_CLK_SEL_MASK | RX_FSYNC_MASK | + TX_FSYNC_MASK | RX_SYNC_SEL_MASK | TX_SYNC_SEL_MASK | + RX_FIFO_ENABLE_MASK | TX_FIFO_ENABLE_MASK | SRG_CLK_SEL_MASK | + LOOPBACK_MASK | TX_EXTRA_DELAY_MASK; + + new_reg = (config->tx_clk_sel | config->rx_clk_sel | + config->rx_fsync_pol | config->tx_fsync_pol | + config->rx_fsync_sel | config->tx_fsync_sel | + config->rx_fifo_config | config->tx_fifo_config | + config->srg_clk_sel | config->loopback_enable | + config->tx_data_enable); + + old_reg = readl(msp->registers + MSP_GCR); + old_reg &= ~mask; + new_reg |= old_reg; + writel(new_reg, msp->registers + MSP_GCR); + + res = enable_msp(msp, config); + if (res < 0) { + dev_err(msp->dev, "%s: ERROR: enable_msp failed (%d)!\n", + __func__, res); + return -EBUSY; + } + if (config->loopback_enable & 0x80) + msp->loopback_enable = 1; + + /* Flush FIFOs */ + flush_fifo_tx(msp); + flush_fifo_rx(msp); + + msp->msp_state = MSP_STATE_CONFIGURED; + return 0; +} + +static void disable_msp_rx(struct ux500_msp *msp) +{ + u32 reg_val_GCR, reg_val_DMACR, reg_val_IMSC; + + reg_val_GCR = readl(msp->registers + MSP_GCR); + writel(reg_val_GCR & ~RX_ENABLE, msp->registers + MSP_GCR); + reg_val_DMACR = readl(msp->registers + MSP_DMACR); + writel(reg_val_DMACR & ~RX_DMA_ENABLE, msp->registers + MSP_DMACR); + reg_val_IMSC = readl(msp->registers + MSP_IMSC); + writel(reg_val_IMSC & + ~(RX_SERVICE_INT | RX_OVERRUN_ERROR_INT), + msp->registers + MSP_IMSC); + + msp->dir_busy &= ~MSP_DIR_RX; +} + +static void disable_msp_tx(struct ux500_msp *msp) +{ + u32 reg_val_GCR, reg_val_DMACR, reg_val_IMSC; + + reg_val_GCR = readl(msp->registers + MSP_GCR); + writel(reg_val_GCR & ~TX_ENABLE, msp->registers + MSP_GCR); + reg_val_DMACR = readl(msp->registers + MSP_DMACR); + writel(reg_val_DMACR & ~TX_DMA_ENABLE, msp->registers + MSP_DMACR); + reg_val_IMSC = readl(msp->registers + MSP_IMSC); + writel(reg_val_IMSC & + ~(TX_SERVICE_INT | TX_UNDERRUN_ERR_INT), + msp->registers + MSP_IMSC); + + msp->dir_busy &= ~MSP_DIR_TX; +} + +static int disable_msp(struct ux500_msp *msp, unsigned int dir) +{ + u32 reg_val_GCR; + unsigned int disable_tx, disable_rx; + + reg_val_GCR = readl(msp->registers + MSP_GCR); + disable_tx = dir & MSP_DIR_TX; + disable_rx = dir & MSP_DIR_TX; + if (disable_tx && disable_rx) { + reg_val_GCR = readl(msp->registers + MSP_GCR); + writel(reg_val_GCR | LOOPBACK_MASK, + msp->registers + MSP_GCR); + + /* Flush TX-FIFO */ + flush_fifo_tx(msp); + + /* Disable TX-channel */ + writel((readl(msp->registers + MSP_GCR) & + (~TX_ENABLE)), msp->registers + MSP_GCR); + + /* Flush RX-FIFO */ + flush_fifo_rx(msp); + + /* Disable Loopback and Receive channel */ + writel((readl(msp->registers + MSP_GCR) & + (~(RX_ENABLE | LOOPBACK_MASK))), + msp->registers + MSP_GCR); + + disable_msp_tx(msp); + disable_msp_rx(msp); + } else if (disable_tx) + disable_msp_tx(msp); + else if (disable_rx) + disable_msp_rx(msp); + + return 0; +} + +int ux500_msp_i2s_trigger(struct ux500_msp *msp, int cmd, int direction) +{ + u32 reg_val_GCR, enable_bit; + + if (msp->msp_state == MSP_STATE_IDLE) { + dev_err(msp->dev, "%s: ERROR: MSP is not configured!\n", + __func__); + return -EINVAL; + } + + switch (cmd) { + case SNDRV_PCM_TRIGGER_START: + case SNDRV_PCM_TRIGGER_RESUME: + case SNDRV_PCM_TRIGGER_PAUSE_RELEASE: + if (direction == SNDRV_PCM_STREAM_PLAYBACK) + enable_bit = TX_ENABLE; + else + enable_bit = RX_ENABLE; + reg_val_GCR = readl(msp->registers + MSP_GCR); + writel(reg_val_GCR | enable_bit, msp->registers + MSP_GCR); + break; + + case SNDRV_PCM_TRIGGER_STOP: + case SNDRV_PCM_TRIGGER_SUSPEND: + case SNDRV_PCM_TRIGGER_PAUSE_PUSH: + if (direction == SNDRV_PCM_STREAM_PLAYBACK) + disable_msp_tx(msp); + else + disable_msp_rx(msp); + break; + default: + return -EINVAL; + } + + return 0; +} + +int ux500_msp_i2s_close(struct ux500_msp *msp, unsigned int dir) +{ + int status = 0; + + dev_dbg(msp->dev, "%s: Enter (dir = 0x%01x).\n", __func__, dir); + + status = disable_msp(msp, dir); + if (msp->dir_busy == 0) { + /* disable sample rate and frame generators */ + msp->msp_state = MSP_STATE_IDLE; + writel((readl(msp->registers + MSP_GCR) & + (~(FRAME_GEN_ENABLE | SRG_ENABLE))), + msp->registers + MSP_GCR); + + writel(0, msp->registers + MSP_GCR); + writel(0, msp->registers + MSP_TCF); + writel(0, msp->registers + MSP_RCF); + writel(0, msp->registers + MSP_DMACR); + writel(0, msp->registers + MSP_SRG); + writel(0, msp->registers + MSP_MCR); + writel(0, msp->registers + MSP_RCM); + writel(0, msp->registers + MSP_RCV); + writel(0, msp->registers + MSP_TCE0); + writel(0, msp->registers + MSP_TCE1); + writel(0, msp->registers + MSP_TCE2); + writel(0, msp->registers + MSP_TCE3); + writel(0, msp->registers + MSP_RCE0); + writel(0, msp->registers + MSP_RCE1); + writel(0, msp->registers + MSP_RCE2); + writel(0, msp->registers + MSP_RCE3); + } + + return status; + +} + +static int ux500_msp_i2s_of_init_msp(struct platform_device *pdev, + struct ux500_msp *msp, + struct msp_i2s_platform_data **platform_data) +{ + struct msp_i2s_platform_data *pdata; + + *platform_data = devm_kzalloc(&pdev->dev, + sizeof(struct msp_i2s_platform_data), + GFP_KERNEL); + pdata = *platform_data; + if (!pdata) + return -ENOMEM; + + msp->playback_dma_data.dma_cfg = devm_kzalloc(&pdev->dev, + sizeof(struct stedma40_chan_cfg), + GFP_KERNEL); + if (!msp->playback_dma_data.dma_cfg) + return -ENOMEM; + + msp->capture_dma_data.dma_cfg = devm_kzalloc(&pdev->dev, + sizeof(struct stedma40_chan_cfg), + GFP_KERNEL); + if (!msp->capture_dma_data.dma_cfg) + return -ENOMEM; + + return 0; +} + +int ux500_msp_i2s_init_msp(struct platform_device *pdev, + struct ux500_msp **msp_p, + struct msp_i2s_platform_data *platform_data) +{ + struct resource *res = NULL; + struct device_node *np = pdev->dev.of_node; + struct ux500_msp *msp; + int ret; + + *msp_p = devm_kzalloc(&pdev->dev, sizeof(struct ux500_msp), GFP_KERNEL); + msp = *msp_p; + if (!msp) + return -ENOMEM; + + if (!platform_data) { + if (np) { + ret = ux500_msp_i2s_of_init_msp(pdev, msp, + &platform_data); + if (ret) + return ret; + } else + return -EINVAL; + } else { + msp->playback_dma_data.dma_cfg = platform_data->msp_i2s_dma_tx; + msp->capture_dma_data.dma_cfg = platform_data->msp_i2s_dma_rx; + msp->id = platform_data->id; + } + + msp->dev = &pdev->dev; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (res == NULL) { + dev_err(&pdev->dev, "%s: ERROR: Unable to get resource!\n", + __func__); + return -ENOMEM; + } + + msp->playback_dma_data.tx_rx_addr = res->start + MSP_DR; + msp->capture_dma_data.tx_rx_addr = res->start + MSP_DR; + + msp->registers = devm_ioremap(&pdev->dev, res->start, + resource_size(res)); + if (msp->registers == NULL) { + dev_err(&pdev->dev, "%s: ERROR: ioremap failed!\n", __func__); + return -ENOMEM; + } + + msp->msp_state = MSP_STATE_IDLE; + msp->loopback_enable = 0; + + return 0; +} + +void ux500_msp_i2s_cleanup_msp(struct platform_device *pdev, + struct ux500_msp *msp) +{ + dev_dbg(msp->dev, "%s: Enter (id = %d).\n", __func__, msp->id); +} + +MODULE_LICENSE("GPL v2"); |