From 5d1646d90e1f2cceb9f0828f4b28318cd0ec7744 Mon Sep 17 00:00:00 2001 From: Daniel Baumann Date: Sat, 27 Apr 2024 12:05:51 +0200 Subject: Adding upstream version 5.10.209. Signed-off-by: Daniel Baumann --- .../bindings/display/mediatek/mediatek,dsi.txt | 72 ++++++++++++++++++++++ 1 file changed, 72 insertions(+) create mode 100644 Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt (limited to 'Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt') diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt new file mode 100644 index 000000000..f06f24d40 --- /dev/null +++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,dsi.txt @@ -0,0 +1,72 @@ +Mediatek DSI Device +=================== + +The Mediatek DSI function block is a sink of the display subsystem and can +drive up to 4-lane MIPI DSI output. Two DSIs can be synchronized for dual- +channel output. + +Required properties: +- compatible: "mediatek,-dsi" +- the supported chips are mt2701, mt7623, mt8173 and mt8183. +- reg: Physical base address and length of the controller's registers +- interrupts: The interrupt signal from the function block. +- clocks: device clocks + See Documentation/devicetree/bindings/clock/clock-bindings.txt for details. +- clock-names: must contain "engine", "digital", and "hs" +- phys: phandle link to the MIPI D-PHY controller. +- phy-names: must contain "dphy" +- port: Output port node with endpoint definitions as described in + Documentation/devicetree/bindings/graph.txt. This port should be connected + to the input port of an attached DSI panel or DSI-to-eDP encoder chip. + +MIPI TX Configuration Module +============================ + +The MIPI TX configuration module controls the MIPI D-PHY. + +Required properties: +- compatible: "mediatek,-mipi-tx" +- the supported chips are mt2701, 7623, mt8173 and mt8183. +- reg: Physical base address and length of the controller's registers +- clocks: PLL reference clock +- clock-output-names: name of the output clock line to the DSI encoder +- #clock-cells: must be <0>; +- #phy-cells: must be <0>. + +Optional properties: +- drive-strength-microamp: adjust driving current, should be 3000 ~ 6000. And + the step is 200. +- nvmem-cells: A phandle to the calibration data provided by a nvmem device. If + unspecified default values shall be used. +- nvmem-cell-names: Should be "calibration-data" + +Example: + +mipi_tx0: mipi-dphy@10215000 { + compatible = "mediatek,mt8173-mipi-tx"; + reg = <0 0x10215000 0 0x1000>; + clocks = <&clk26m>; + clock-output-names = "mipi_tx0_pll"; + #clock-cells = <0>; + #phy-cells = <0>; + drive-strength-microamp = <4600>; + nvmem-cells= <&mipi_tx_calibration>; + nvmem-cell-names = "calibration-data"; +}; + +dsi0: dsi@1401b000 { + compatible = "mediatek,mt8173-dsi"; + reg = <0 0x1401b000 0 0x1000>; + interrupts = ; + clocks = <&mmsys MM_DSI0_ENGINE>, <&mmsys MM_DSI0_DIGITAL>, + <&mipi_tx0>; + clock-names = "engine", "digital", "hs"; + phys = <&mipi_tx0>; + phy-names = "dphy"; + + port { + dsi0_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; +}; -- cgit v1.2.3