From 5d1646d90e1f2cceb9f0828f4b28318cd0ec7744 Mon Sep 17 00:00:00 2001 From: Daniel Baumann Date: Sat, 27 Apr 2024 12:05:51 +0200 Subject: Adding upstream version 5.10.209. Signed-off-by: Daniel Baumann --- .../devicetree/bindings/mux/adi,adg792a.txt | 75 ++++++++++ .../devicetree/bindings/mux/adi,adgs1408.txt | 48 +++++++ Documentation/devicetree/bindings/mux/gpio-mux.txt | 69 +++++++++ .../devicetree/bindings/mux/mux-controller.txt | 157 +++++++++++++++++++++ Documentation/devicetree/bindings/mux/reg-mux.txt | 129 +++++++++++++++++ 5 files changed, 478 insertions(+) create mode 100644 Documentation/devicetree/bindings/mux/adi,adg792a.txt create mode 100644 Documentation/devicetree/bindings/mux/adi,adgs1408.txt create mode 100644 Documentation/devicetree/bindings/mux/gpio-mux.txt create mode 100644 Documentation/devicetree/bindings/mux/mux-controller.txt create mode 100644 Documentation/devicetree/bindings/mux/reg-mux.txt (limited to 'Documentation/devicetree/bindings/mux') diff --git a/Documentation/devicetree/bindings/mux/adi,adg792a.txt b/Documentation/devicetree/bindings/mux/adi,adg792a.txt new file mode 100644 index 000000000..96b787a69 --- /dev/null +++ b/Documentation/devicetree/bindings/mux/adi,adg792a.txt @@ -0,0 +1,75 @@ +Bindings for Analog Devices ADG792A/G Triple 4:1 Multiplexers + +Required properties: +- compatible : "adi,adg792a" or "adi,adg792g" +- #mux-control-cells : <0> if parallel (the three muxes are bound together + with a single mux controller controlling all three muxes), or <1> if + not (one mux controller for each mux). +* Standard mux-controller bindings as described in mux-controller.txt + +Optional properties for ADG792G: +- gpio-controller : if present, #gpio-cells below is required. +- #gpio-cells : should be <2> + - First cell is the GPO line number, i.e. 0 or 1 + - Second cell is used to specify active high (0) + or active low (1) + +Optional properties: +- idle-state : if present, array of states that the mux controllers will have + when idle. The special state MUX_IDLE_AS_IS is the default and + MUX_IDLE_DISCONNECT is also supported. + +States 0 through 3 correspond to signals A through D in the datasheet. + +Example: + + /* + * Three independent mux controllers (of which one is used). + * Mux 0 is disconnected when idle, mux 1 idles in the previously + * selected state and mux 2 idles with signal B. + */ + &i2c0 { + mux: mux-controller@50 { + compatible = "adi,adg792a"; + reg = <0x50>; + #mux-control-cells = <1>; + + idle-state = ; + }; + }; + + adc-mux { + compatible = "io-channel-mux"; + io-channels = <&adc 0>; + io-channel-names = "parent"; + + mux-controls = <&mux 2>; + + channels = "sync-1", "", "out"; + }; + + + /* + * Three parallel muxes with one mux controller, useful e.g. if + * the adc is differential, thus needing two signals to be muxed + * simultaneously for correct operation. + */ + &i2c0 { + pmux: mux-controller@50 { + compatible = "adi,adg792a"; + reg = <0x50>; + #mux-control-cells = <0>; + + idle-state = <1>; + }; + }; + + diff-adc-mux { + compatible = "io-channel-mux"; + io-channels = <&adc 0>; + io-channel-names = "parent"; + + mux-controls = <&pmux>; + + channels = "sync-1", "", "out"; + }; diff --git a/Documentation/devicetree/bindings/mux/adi,adgs1408.txt b/Documentation/devicetree/bindings/mux/adi,adgs1408.txt new file mode 100644 index 000000000..be6947f4d --- /dev/null +++ b/Documentation/devicetree/bindings/mux/adi,adgs1408.txt @@ -0,0 +1,48 @@ +Bindings for Analog Devices ADGS1408/1409 8:1/Dual 4:1 Mux + +Required properties: +- compatible : Should be one of + * "adi,adgs1408" + * "adi,adgs1409" +* Standard mux-controller bindings as described in mux-controller.txt + +Optional properties for ADGS1408/1409: +- gpio-controller : if present, #gpio-cells is required. +- #gpio-cells : should be <2> + - First cell is the GPO line number, i.e. 0 to 3 + for ADGS1408 and 0 to 4 for ADGS1409 + - Second cell is used to specify active high (0) + or active low (1) + +Optional properties: +- idle-state : if present, the state that the mux controller will have + when idle. The special state MUX_IDLE_AS_IS is the default and + MUX_IDLE_DISCONNECT is also supported. + +States 0 through 7 correspond to signals S1 through S8 in the datasheet. +For ADGS1409 only states 0 to 3 are available. + +Example: + + /* + * One mux controller. + * Mux state set to idle as is (no idle-state declared) + */ + &spi0 { + mux: mux-controller@0 { + compatible = "adi,adgs1408"; + reg = <0>; + spi-max-frequency = <1000000>; + #mux-control-cells = <0>; + }; + } + + adc-mux { + compatible = "io-channel-mux"; + io-channels = <&adc 1>; + io-channel-names = "parent"; + mux-controls = <&mux>; + + channels = "out_a0", "out_a1", "test0", "test1", + "out_b0", "out_b1", "testb0", "testb1"; + }; diff --git a/Documentation/devicetree/bindings/mux/gpio-mux.txt b/Documentation/devicetree/bindings/mux/gpio-mux.txt new file mode 100644 index 000000000..b8f746344 --- /dev/null +++ b/Documentation/devicetree/bindings/mux/gpio-mux.txt @@ -0,0 +1,69 @@ +GPIO-based multiplexer controller bindings + +Define what GPIO pins are used to control a multiplexer. Or several +multiplexers, if the same pins control more than one multiplexer. + +Required properties: +- compatible : "gpio-mux" +- mux-gpios : list of gpios used to control the multiplexer, least + significant bit first. +- #mux-control-cells : <0> +* Standard mux-controller bindings as decribed in mux-controller.txt + +Optional properties: +- idle-state : if present, the state the mux will have when idle. The + special state MUX_IDLE_AS_IS is the default. + +The multiplexer state is defined as the number represented by the +multiplexer GPIO pins, where the first pin is the least significant +bit. An active pin is a binary 1, an inactive pin is a binary 0. + +Example: + + mux: mux-controller { + compatible = "gpio-mux"; + #mux-control-cells = <0>; + + mux-gpios = <&pioA 0 GPIO_ACTIVE_HIGH>, + <&pioA 1 GPIO_ACTIVE_HIGH>; + }; + + adc-mux { + compatible = "io-channel-mux"; + io-channels = <&adc 0>; + io-channel-names = "parent"; + + mux-controls = <&mux>; + + channels = "sync-1", "in", "out", "sync-2"; + }; + + i2c-mux { + compatible = "i2c-mux"; + i2c-parent = <&i2c1>; + + mux-controls = <&mux>; + + #address-cells = <1>; + #size-cells = <0>; + + i2c@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + + ssd1307: oled@3c { + /* ... */ + }; + }; + + i2c@3 { + reg = <3>; + #address-cells = <1>; + #size-cells = <0>; + + pca9555: pca9555@20 { + /* ... */ + }; + }; + }; diff --git a/Documentation/devicetree/bindings/mux/mux-controller.txt b/Documentation/devicetree/bindings/mux/mux-controller.txt new file mode 100644 index 000000000..4f47e4bd2 --- /dev/null +++ b/Documentation/devicetree/bindings/mux/mux-controller.txt @@ -0,0 +1,157 @@ +Common multiplexer controller bindings +====================================== + +A multiplexer (or mux) controller will have one, or several, consumer devices +that uses the mux controller. Thus, a mux controller can possibly control +several parallel multiplexers. Presumably there will be at least one +multiplexer needed by each consumer, but a single mux controller can of course +control several multiplexers for a single consumer. + +A mux controller provides a number of states to its consumers, and the state +space is a simple zero-based enumeration. I.e. 0-1 for a 2-way multiplexer, +0-7 for an 8-way multiplexer, etc. + + +Consumers +--------- + +Mux controller consumers should specify a list of mux controllers that they +want to use with a property containing a 'mux-ctrl-list': + + mux-ctrl-list ::= [mux-ctrl-list] + single-mux-ctrl ::= [mux-ctrl-specifier] + mux-ctrl-phandle : phandle to mux controller node + mux-ctrl-specifier : array of #mux-control-cells specifying the + given mux controller (controller specific) + +Mux controller properties should be named "mux-controls". The exact meaning of +each mux controller property must be documented in the device tree binding for +each consumer. An optional property "mux-control-names" may contain a list of +strings to label each of the mux controllers listed in the "mux-controls" +property. + +Drivers for devices that use more than a single mux controller can use the +"mux-control-names" property to map the name of the requested mux controller +to an index into the list given by the "mux-controls" property. + +mux-ctrl-specifier typically encodes the chip-relative mux controller number. +If the mux controller chip only provides a single mux controller, the +mux-ctrl-specifier can typically be left out. + +Example: + + /* One consumer of a 2-way mux controller (one GPIO-line) */ + mux: mux-controller { + compatible = "gpio-mux"; + #mux-control-cells = <0>; + + mux-gpios = <&pioA 0 GPIO_ACTIVE_HIGH>; + }; + + adc-mux { + compatible = "io-channel-mux"; + io-channels = <&adc 0>; + io-channel-names = "parent"; + + mux-controls = <&mux>; + mux-control-names = "adc"; + + channels = "sync", "in"; + }; + +Note that in the example above, specifying the "mux-control-names" is redundant +because there is only one mux controller in the list. However, if the driver +for the consumer node in fact asks for a named mux controller, that name is of +course still required. + + /* + * Two consumers (one for an ADC line and one for an i2c bus) of + * parallel 4-way multiplexers controlled by the same two GPIO-lines. + */ + mux: mux-controller { + compatible = "gpio-mux"; + #mux-control-cells = <0>; + + mux-gpios = <&pioA 0 GPIO_ACTIVE_HIGH>, + <&pioA 1 GPIO_ACTIVE_HIGH>; + }; + + adc-mux { + compatible = "io-channel-mux"; + io-channels = <&adc 0>; + io-channel-names = "parent"; + + mux-controls = <&mux>; + + channels = "sync-1", "in", "out", "sync-2"; + }; + + i2c-mux { + compatible = "i2c-mux"; + i2c-parent = <&i2c1>; + + mux-controls = <&mux>; + + #address-cells = <1>; + #size-cells = <0>; + + i2c@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + + ssd1307: oled@3c { + /* ... */ + }; + }; + + i2c@3 { + reg = <3>; + #address-cells = <1>; + #size-cells = <0>; + + pca9555: pca9555@20 { + /* ... */ + }; + }; + }; + + +Mux controller nodes +-------------------- + +Mux controller nodes must specify the number of cells used for the +specifier using the '#mux-control-cells' property. + +Optionally, mux controller nodes can also specify the state the mux should +have when it is idle. The idle-state property is used for this. If the +idle-state is not present, the mux controller is typically left as is when +it is idle. For multiplexer chips that expose several mux controllers, the +idle-state property is an array with one idle state for each mux controller. + +The special value (-1) may be used to indicate that the mux should be left +as is when it is idle. This is the default, but can still be useful for +mux controller chips with more than one mux controller, particularly when +there is a need to "step past" a mux controller and set some other idle +state for a mux controller with a higher index. + +Some mux controllers have the ability to disconnect the input/output of the +multiplexer. Using this disconnected high-impedance state as the idle state +is indicated with idle state (-2). + +These constants are available in + + #include + +as MUX_IDLE_AS_IS (-1) and MUX_IDLE_DISCONNECT (-2). + +An example mux controller node look like this (the adg972a chip is a triple +4-way multiplexer): + + mux: mux-controller@50 { + compatible = "adi,adg792a"; + reg = <0x50>; + #mux-control-cells = <1>; + + idle-state = ; + }; diff --git a/Documentation/devicetree/bindings/mux/reg-mux.txt b/Documentation/devicetree/bindings/mux/reg-mux.txt new file mode 100644 index 000000000..4afd7ba73 --- /dev/null +++ b/Documentation/devicetree/bindings/mux/reg-mux.txt @@ -0,0 +1,129 @@ +Generic register bitfield-based multiplexer controller bindings + +Define register bitfields to be used to control multiplexers. The parent +device tree node must be a device node to provide register r/w access. + +Required properties: +- compatible : should be one of + "reg-mux" : if parent device of mux controller is not syscon device + "mmio-mux" : if parent device of mux controller is syscon device +- #mux-control-cells : <1> +- mux-reg-masks : an array of register offset and pre-shifted bitfield mask + pairs, each describing a single mux control. +* Standard mux-controller bindings as decribed in mux-controller.txt + +Optional properties: +- idle-states : if present, the state the muxes will have when idle. The + special state MUX_IDLE_AS_IS is the default. + +The multiplexer state of each multiplexer is defined as the value of the +bitfield described by the corresponding register offset and bitfield mask +pair in the mux-reg-masks array. + +Example 1: +The parent device of mux controller is not a syscon device. + +&i2c0 { + fpga@66 { // fpga connected to i2c + compatible = "fsl,lx2160aqds-fpga", "fsl,fpga-qixis-i2c", + "simple-mfd"; + reg = <0x66>; + + mux: mux-controller { + compatible = "reg-mux"; + #mux-control-cells = <1>; + mux-reg-masks = <0x54 0xf8>, /* 0: reg 0x54, bits 7:3 */ + <0x54 0x07>; /* 1: reg 0x54, bits 2:0 */ + }; + }; +}; + +mdio-mux-1 { + compatible = "mdio-mux-multiplexer"; + mux-controls = <&mux 0>; + mdio-parent-bus = <&emdio1>; + #address-cells = <1>; + #size-cells = <0>; + + mdio@0 { + reg = <0x0>; + #address-cells = <1>; + #size-cells = <0>; + }; + + mdio@8 { + reg = <0x8>; + #address-cells = <1>; + #size-cells = <0>; + }; + + .. + .. +}; + +mdio-mux-2 { + compatible = "mdio-mux-multiplexer"; + mux-controls = <&mux 1>; + mdio-parent-bus = <&emdio2>; + #address-cells = <1>; + #size-cells = <0>; + + mdio@0 { + reg = <0x0>; + #address-cells = <1>; + #size-cells = <0>; + }; + + mdio@1 { + reg = <0x1>; + #address-cells = <1>; + #size-cells = <0>; + }; + + .. + .. +}; + +Example 2: +The parent device of mux controller is syscon device. + +syscon { + compatible = "syscon"; + + mux: mux-controller { + compatible = "mmio-mux"; + #mux-control-cells = <1>; + + mux-reg-masks = <0x3 0x30>, /* 0: reg 0x3, bits 5:4 */ + <0x3 0x40>, /* 1: reg 0x3, bit 6 */ + idle-states = , <0>; + }; +}; + +video-mux { + compatible = "video-mux"; + mux-controls = <&mux 0>; + #address-cells = <1>; + #size-cells = <0>; + + ports { + /* inputs 0..3 */ + port@0 { + reg = <0>; + }; + port@1 { + reg = <1>; + }; + port@2 { + reg = <2>; + }; + port@3 { + reg = <3>; + }; + + /* output */ + port@4 { + reg = <4>; + }; + }; +}; -- cgit v1.2.3