From 5d1646d90e1f2cceb9f0828f4b28318cd0ec7744 Mon Sep 17 00:00:00 2001
From: Daniel Baumann <daniel.baumann@progress-linux.org>
Date: Sat, 27 Apr 2024 12:05:51 +0200
Subject: Adding upstream version 5.10.209.

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>
---
 Documentation/x86/earlyprintk.rst | 151 ++++++++++++++++++++++++++++++++++++++
 1 file changed, 151 insertions(+)
 create mode 100644 Documentation/x86/earlyprintk.rst

(limited to 'Documentation/x86/earlyprintk.rst')

diff --git a/Documentation/x86/earlyprintk.rst b/Documentation/x86/earlyprintk.rst
new file mode 100644
index 000000000..51ef11e8f
--- /dev/null
+++ b/Documentation/x86/earlyprintk.rst
@@ -0,0 +1,151 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+============
+Early Printk
+============
+
+Mini-HOWTO for using the earlyprintk=dbgp boot option with a
+USB2 Debug port key and a debug cable, on x86 systems.
+
+You need two computers, the 'USB debug key' special gadget and
+two USB cables, connected like this::
+
+  [host/target] <-------> [USB debug key] <-------> [client/console]
+
+Hardware requirements
+=====================
+
+  a) Host/target system needs to have USB debug port capability.
+
+     You can check this capability by looking at a 'Debug port' bit in
+     the lspci -vvv output::
+
+       # lspci -vvv
+       ...
+       00:1d.7 USB Controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 03) (prog-if 20 [EHCI])
+               Subsystem: Lenovo ThinkPad T61
+               Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
+               Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
+               Latency: 0
+               Interrupt: pin D routed to IRQ 19
+               Region 0: Memory at fe227000 (32-bit, non-prefetchable) [size=1K]
+               Capabilities: [50] Power Management version 2
+                       Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
+                       Status: D0 PME-Enable- DSel=0 DScale=0 PME+
+               Capabilities: [58] Debug port: BAR=1 offset=00a0
+                            ^^^^^^^^^^^ <==================== [ HERE ]
+               Kernel driver in use: ehci_hcd
+               Kernel modules: ehci-hcd
+       ...
+
+     .. note::
+       If your system does not list a debug port capability then you probably
+       won't be able to use the USB debug key.
+
+  b) You also need a NetChip USB debug cable/key:
+
+        http://www.plxtech.com/products/NET2000/NET20DC/default.asp
+
+     This is a small blue plastic connector with two USB connections;
+     it draws power from its USB connections.
+
+  c) You need a second client/console system with a high speed USB 2.0 port.
+
+  d) The NetChip device must be plugged directly into the physical
+     debug port on the "host/target" system. You cannot use a USB hub in
+     between the physical debug port and the "host/target" system.
+
+     The EHCI debug controller is bound to a specific physical USB
+     port and the NetChip device will only work as an early printk
+     device in this port.  The EHCI host controllers are electrically
+     wired such that the EHCI debug controller is hooked up to the
+     first physical port and there is no way to change this via software.
+     You can find the physical port through experimentation by trying
+     each physical port on the system and rebooting.  Or you can try
+     and use lsusb or look at the kernel info messages emitted by the
+     usb stack when you plug a usb device into various ports on the
+     "host/target" system.
+
+     Some hardware vendors do not expose the usb debug port with a
+     physical connector and if you find such a device send a complaint
+     to the hardware vendor, because there is no reason not to wire
+     this port into one of the physically accessible ports.
+
+  e) It is also important to note, that many versions of the NetChip
+     device require the "client/console" system to be plugged into the
+     right hand side of the device (with the product logo facing up and
+     readable left to right).  The reason being is that the 5 volt
+     power supply is taken from only one side of the device and it
+     must be the side that does not get rebooted.
+
+Software requirements
+=====================
+
+  a) On the host/target system:
+
+    You need to enable the following kernel config option::
+
+      CONFIG_EARLY_PRINTK_DBGP=y
+
+    And you need to add the boot command line: "earlyprintk=dbgp".
+
+    .. note::
+      If you are using Grub, append it to the 'kernel' line in
+      /etc/grub.conf.  If you are using Grub2 on a BIOS firmware system,
+      append it to the 'linux' line in /boot/grub2/grub.cfg. If you are
+      using Grub2 on an EFI firmware system, append it to the 'linux'
+      or 'linuxefi' line in /boot/grub2/grub.cfg or
+      /boot/efi/EFI/<distro>/grub.cfg.
+
+    On systems with more than one EHCI debug controller you must
+    specify the correct EHCI debug controller number.  The ordering
+    comes from the PCI bus enumeration of the EHCI controllers.  The
+    default with no number argument is "0" or the first EHCI debug
+    controller.  To use the second EHCI debug controller, you would
+    use the command line: "earlyprintk=dbgp1"
+
+    .. note::
+      normally earlyprintk console gets turned off once the
+      regular console is alive - use "earlyprintk=dbgp,keep" to keep
+      this channel open beyond early bootup. This can be useful for
+      debugging crashes under Xorg, etc.
+
+  b) On the client/console system:
+
+    You should enable the following kernel config option::
+
+      CONFIG_USB_SERIAL_DEBUG=y
+
+    On the next bootup with the modified kernel you should
+    get a /dev/ttyUSBx device(s).
+
+    Now this channel of kernel messages is ready to be used: start
+    your favorite terminal emulator (minicom, etc.) and set
+    it up to use /dev/ttyUSB0 - or use a raw 'cat /dev/ttyUSBx' to
+    see the raw output.
+
+  c) On Nvidia Southbridge based systems: the kernel will try to probe
+     and find out which port has a debug device connected.
+
+Testing
+=======
+
+You can test the output by using earlyprintk=dbgp,keep and provoking
+kernel messages on the host/target system. You can provoke a harmless
+kernel message by for example doing::
+
+     echo h > /proc/sysrq-trigger
+
+On the host/target system you should see this help line in "dmesg" output::
+
+     SysRq : HELP : loglevel(0-9) reBoot Crashdump terminate-all-tasks(E) memory-full-oom-kill(F) kill-all-tasks(I) saK show-backtrace-all-active-cpus(L) show-memory-usage(M) nice-all-RT-tasks(N) powerOff show-registers(P) show-all-timers(Q) unRaw Sync show-task-states(T) Unmount show-blocked-tasks(W) dump-ftrace-buffer(Z)
+
+On the client/console system do::
+
+       cat /dev/ttyUSB0
+
+And you should see the help line above displayed shortly after you've
+provoked it on the host system.
+
+If it does not work then please ask about it on the linux-kernel@vger.kernel.org
+mailing list or contact the x86 maintainers.
-- 
cgit v1.2.3