From 5d1646d90e1f2cceb9f0828f4b28318cd0ec7744 Mon Sep 17 00:00:00 2001 From: Daniel Baumann Date: Sat, 27 Apr 2024 12:05:51 +0200 Subject: Adding upstream version 5.10.209. Signed-off-by: Daniel Baumann --- drivers/net/wireless/ti/wl12xx/reg.h | 542 +++++++++++++++++++++++++++++++++++ 1 file changed, 542 insertions(+) create mode 100644 drivers/net/wireless/ti/wl12xx/reg.h (limited to 'drivers/net/wireless/ti/wl12xx/reg.h') diff --git a/drivers/net/wireless/ti/wl12xx/reg.h b/drivers/net/wireless/ti/wl12xx/reg.h new file mode 100644 index 000000000..8ff018808 --- /dev/null +++ b/drivers/net/wireless/ti/wl12xx/reg.h @@ -0,0 +1,542 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ +/* + * This file is part of wl12xx + * + * Copyright (C) 1998-2009 Texas Instruments. All rights reserved. + * Copyright (C) 2009 Nokia Corporation + * + * Contact: Luciano Coelho + */ + +#ifndef __REG_H__ +#define __REG_H__ + +#include + +#define REGISTERS_BASE 0x00300000 +#define DRPW_BASE 0x00310000 + +#define REGISTERS_DOWN_SIZE 0x00008800 +#define REGISTERS_WORK_SIZE 0x0000b000 + +#define FW_STATUS_ADDR (0x14FC0 + 0xA000) + +/*=============================================== + Host Software Reset - 32bit RW + ------------------------------------------ + [31:1] Reserved + 0 SOFT_RESET Soft Reset - When this bit is set, + it holds the Wlan hardware in a soft reset state. + This reset disables all MAC and baseband processor + clocks except the CardBus/PCI interface clock. + It also initializes all MAC state machines except + the host interface. It does not reload the + contents of the EEPROM. When this bit is cleared + (not self-clearing), the Wlan hardware + exits the software reset state. +===============================================*/ +#define WL12XX_SLV_SOFT_RESET (REGISTERS_BASE + 0x0000) + +#define WL1271_SLV_REG_DATA (REGISTERS_BASE + 0x0008) +#define WL1271_SLV_REG_ADATA (REGISTERS_BASE + 0x000c) +#define WL1271_SLV_MEM_DATA (REGISTERS_BASE + 0x0018) + +#define WL12XX_REG_INTERRUPT_TRIG (REGISTERS_BASE + 0x0474) +#define WL12XX_REG_INTERRUPT_TRIG_H (REGISTERS_BASE + 0x0478) + +/*============================================= + Host Interrupt Mask Register - 32bit (RW) + ------------------------------------------ + Setting a bit in this register masks the + corresponding interrupt to the host. + 0 - RX0 - Rx first dubble buffer Data Interrupt + 1 - TXD - Tx Data Interrupt + 2 - TXXFR - Tx Transfer Interrupt + 3 - RX1 - Rx second dubble buffer Data Interrupt + 4 - RXXFR - Rx Transfer Interrupt + 5 - EVENT_A - Event Mailbox interrupt + 6 - EVENT_B - Event Mailbox interrupt + 7 - WNONHST - Wake On Host Interrupt + 8 - TRACE_A - Debug Trace interrupt + 9 - TRACE_B - Debug Trace interrupt + 10 - CDCMP - Command Complete Interrupt + 11 - + 12 - + 13 - + 14 - ICOMP - Initialization Complete Interrupt + 16 - SG SE - Soft Gemini - Sense enable interrupt + 17 - SG SD - Soft Gemini - Sense disable interrupt + 18 - - + 19 - - + 20 - - + 21- - + Default: 0x0001 +*==============================================*/ +#define WL12XX_REG_INTERRUPT_MASK (REGISTERS_BASE + 0x04DC) + +/*============================================= + Host Interrupt Mask Set 16bit, (Write only) + ------------------------------------------ + Setting a bit in this register sets + the corresponding bin in ACX_HINT_MASK register + without effecting the mask + state of other bits (0 = no effect). +==============================================*/ +#define ACX_REG_HINT_MASK_SET (REGISTERS_BASE + 0x04E0) + +/*============================================= + Host Interrupt Mask Clear 16bit,(Write only) + ------------------------------------------ + Setting a bit in this register clears + the corresponding bin in ACX_HINT_MASK register + without effecting the mask + state of other bits (0 = no effect). +=============================================*/ +#define ACX_REG_HINT_MASK_CLR (REGISTERS_BASE + 0x04E4) + +/*============================================= + Host Interrupt Status Nondestructive Read + 16bit,(Read only) + ------------------------------------------ + The host can read this register to determine + which interrupts are active. + Reading this register doesn't + effect its content. +=============================================*/ +#define WL12XX_REG_INTERRUPT_NO_CLEAR (REGISTERS_BASE + 0x04E8) + +/*============================================= + Host Interrupt Status Clear on Read Register + 16bit,(Read only) + ------------------------------------------ + The host can read this register to determine + which interrupts are active. + Reading this register clears it, + thus making all interrupts inactive. +==============================================*/ +#define ACX_REG_INTERRUPT_CLEAR (REGISTERS_BASE + 0x04F8) + +/*============================================= + Host Interrupt Acknowledge Register + 16bit,(Write only) + ------------------------------------------ + The host can set individual bits in this + register to clear (acknowledge) the corresp. + interrupt status bits in the HINT_STS_CLR and + HINT_STS_ND registers, thus making the + assotiated interrupt inactive. (0-no effect) +==============================================*/ +#define WL12XX_REG_INTERRUPT_ACK (REGISTERS_BASE + 0x04F0) + +#define WL12XX_REG_RX_DRIVER_COUNTER (REGISTERS_BASE + 0x0538) + +/* Device Configuration registers*/ +#define SOR_CFG (REGISTERS_BASE + 0x0800) + +/* Embedded ARM CPU Control */ + +/*=============================================== + Halt eCPU - 32bit RW + ------------------------------------------ + 0 HALT_ECPU Halt Embedded CPU - This bit is the + complement of bit 1 (MDATA2) in the SOR_CFG register. + During a hardware reset, this bit holds + the inverse of MDATA2. + When downloading firmware from the host, + set this bit (pull down MDATA2). + The host clears this bit after downloading the firmware into + zero-wait-state SSRAM. + When loading firmware from Flash, clear this bit (pull up MDATA2) + so that the eCPU can run the bootloader code in Flash + HALT_ECPU eCPU State + -------------------- + 1 halt eCPU + 0 enable eCPU + ===============================================*/ +#define WL12XX_REG_ECPU_CONTROL (REGISTERS_BASE + 0x0804) + +#define WL12XX_HI_CFG (REGISTERS_BASE + 0x0808) + +/*=============================================== + EEPROM Burst Read Start - 32bit RW + ------------------------------------------ + [31:1] Reserved + 0 ACX_EE_START - EEPROM Burst Read Start 0 + Setting this bit starts a burst read from + the external EEPROM. + If this bit is set (after reset) before an EEPROM read/write, + the burst read starts at EEPROM address 0. + Otherwise, it starts at the address + following the address of the previous access. + TheWlan hardware hardware clears this bit automatically. + + Default: 0x00000000 +*================================================*/ +#define ACX_REG_EE_START (REGISTERS_BASE + 0x080C) + +#define WL12XX_OCP_POR_CTR (REGISTERS_BASE + 0x09B4) +#define WL12XX_OCP_DATA_WRITE (REGISTERS_BASE + 0x09B8) +#define WL12XX_OCP_DATA_READ (REGISTERS_BASE + 0x09BC) +#define WL12XX_OCP_CMD (REGISTERS_BASE + 0x09C0) + +#define WL12XX_HOST_WR_ACCESS (REGISTERS_BASE + 0x09F8) + +#define WL12XX_CHIP_ID_B (REGISTERS_BASE + 0x5674) + +#define WL12XX_ENABLE (REGISTERS_BASE + 0x5450) + +/* Power Management registers */ +#define WL12XX_ELP_CFG_MODE (REGISTERS_BASE + 0x5804) +#define WL12XX_ELP_CMD (REGISTERS_BASE + 0x5808) +#define WL12XX_PLL_CAL_TIME (REGISTERS_BASE + 0x5810) +#define WL12XX_CLK_REQ_TIME (REGISTERS_BASE + 0x5814) +#define WL12XX_CLK_BUF_TIME (REGISTERS_BASE + 0x5818) + +#define WL12XX_CFG_PLL_SYNC_CNT (REGISTERS_BASE + 0x5820) + +/* Scratch Pad registers*/ +#define WL12XX_SCR_PAD0 (REGISTERS_BASE + 0x5608) +#define WL12XX_SCR_PAD1 (REGISTERS_BASE + 0x560C) +#define WL12XX_SCR_PAD2 (REGISTERS_BASE + 0x5610) +#define WL12XX_SCR_PAD3 (REGISTERS_BASE + 0x5614) +#define WL12XX_SCR_PAD4 (REGISTERS_BASE + 0x5618) +#define WL12XX_SCR_PAD4_SET (REGISTERS_BASE + 0x561C) +#define WL12XX_SCR_PAD4_CLR (REGISTERS_BASE + 0x5620) +#define WL12XX_SCR_PAD5 (REGISTERS_BASE + 0x5624) +#define WL12XX_SCR_PAD5_SET (REGISTERS_BASE + 0x5628) +#define WL12XX_SCR_PAD5_CLR (REGISTERS_BASE + 0x562C) +#define WL12XX_SCR_PAD6 (REGISTERS_BASE + 0x5630) +#define WL12XX_SCR_PAD7 (REGISTERS_BASE + 0x5634) +#define WL12XX_SCR_PAD8 (REGISTERS_BASE + 0x5638) +#define WL12XX_SCR_PAD9 (REGISTERS_BASE + 0x563C) + +/* Spare registers*/ +#define WL12XX_SPARE_A1 (REGISTERS_BASE + 0x0994) +#define WL12XX_SPARE_A2 (REGISTERS_BASE + 0x0998) +#define WL12XX_SPARE_A3 (REGISTERS_BASE + 0x099C) +#define WL12XX_SPARE_A4 (REGISTERS_BASE + 0x09A0) +#define WL12XX_SPARE_A5 (REGISTERS_BASE + 0x09A4) +#define WL12XX_SPARE_A6 (REGISTERS_BASE + 0x09A8) +#define WL12XX_SPARE_A7 (REGISTERS_BASE + 0x09AC) +#define WL12XX_SPARE_A8 (REGISTERS_BASE + 0x09B0) +#define WL12XX_SPARE_B1 (REGISTERS_BASE + 0x5420) +#define WL12XX_SPARE_B2 (REGISTERS_BASE + 0x5424) +#define WL12XX_SPARE_B3 (REGISTERS_BASE + 0x5428) +#define WL12XX_SPARE_B4 (REGISTERS_BASE + 0x542C) +#define WL12XX_SPARE_B5 (REGISTERS_BASE + 0x5430) +#define WL12XX_SPARE_B6 (REGISTERS_BASE + 0x5434) +#define WL12XX_SPARE_B7 (REGISTERS_BASE + 0x5438) +#define WL12XX_SPARE_B8 (REGISTERS_BASE + 0x543C) + +#define WL12XX_PLL_PARAMETERS (REGISTERS_BASE + 0x6040) +#define WL12XX_WU_COUNTER_PAUSE (REGISTERS_BASE + 0x6008) +#define WL12XX_WELP_ARM_COMMAND (REGISTERS_BASE + 0x6100) +#define WL12XX_DRPW_SCRATCH_START (DRPW_BASE + 0x002C) + +#define WL12XX_CMD_MBOX_ADDRESS 0x407B4 + +#define ACX_REG_EEPROM_START_BIT BIT(1) + +/* Command/Information Mailbox Pointers */ + +/*=============================================== + Command Mailbox Pointer - 32bit RW + ------------------------------------------ + This register holds the start address of + the command mailbox located in the Wlan hardware memory. + The host must read this pointer after a reset to + find the location of the command mailbox. + The Wlan hardware initializes the command mailbox + pointer with the default address of the command mailbox. + The command mailbox pointer is not valid until after + the host receives the Init Complete interrupt from + the Wlan hardware. + ===============================================*/ +#define WL12XX_REG_COMMAND_MAILBOX_PTR (WL12XX_SCR_PAD0) + +/*=============================================== + Information Mailbox Pointer - 32bit RW + ------------------------------------------ + This register holds the start address of + the information mailbox located in the Wlan hardware memory. + The host must read this pointer after a reset to find + the location of the information mailbox. + The Wlan hardware initializes the information mailbox pointer + with the default address of the information mailbox. + The information mailbox pointer is not valid + until after the host receives the Init Complete interrupt from + the Wlan hardware. + ===============================================*/ +#define WL12XX_REG_EVENT_MAILBOX_PTR (WL12XX_SCR_PAD1) + +/*=============================================== + EEPROM Read/Write Request 32bit RW + ------------------------------------------ + 1 EE_READ - EEPROM Read Request 1 - Setting this bit + loads a single byte of data into the EE_DATA + register from the EEPROM location specified in + the EE_ADDR register. + The Wlan hardware hardware clears this bit automatically. + EE_DATA is valid when this bit is cleared. + + 0 EE_WRITE - EEPROM Write Request - Setting this bit + writes a single byte of data from the EE_DATA register into the + EEPROM location specified in the EE_ADDR register. + The Wlan hardware hardware clears this bit automatically. +*===============================================*/ +#define ACX_EE_CTL_REG EE_CTL +#define EE_WRITE 0x00000001ul +#define EE_READ 0x00000002ul + +/*=============================================== + EEPROM Address - 32bit RW + ------------------------------------------ + This register specifies the address + within the EEPROM from/to which to read/write data. + ===============================================*/ +#define ACX_EE_ADDR_REG EE_ADDR + +/*=============================================== + EEPROM Data - 32bit RW + ------------------------------------------ + This register either holds the read 8 bits of + data from the EEPROM or the write data + to be written to the EEPROM. + ===============================================*/ +#define ACX_EE_DATA_REG EE_DATA + +/*=============================================== + EEPROM Base Address - 32bit RW + ------------------------------------------ + This register holds the upper nine bits + [23:15] of the 24-bit Wlan hardware memory + address for burst reads from EEPROM accesses. + The EEPROM provides the lower 15 bits of this address. + The MSB of the address from the EEPROM is ignored. + ===============================================*/ +#define ACX_EE_CFG EE_CFG + +/*=============================================== + GPIO Output Values -32bit, RW + ------------------------------------------ + [31:16] Reserved + [15: 0] Specify the output values (at the output driver inputs) for + GPIO[15:0], respectively. + ===============================================*/ +#define ACX_GPIO_OUT_REG GPIO_OUT +#define ACX_MAX_GPIO_LINES 15 + +/*=============================================== + Contention window -32bit, RW + ------------------------------------------ + [31:26] Reserved + [25:16] Max (0x3ff) + [15:07] Reserved + [06:00] Current contention window value - default is 0x1F + ===============================================*/ +#define ACX_CONT_WIND_CFG_REG CONT_WIND_CFG +#define ACX_CONT_WIND_MIN_MASK 0x0000007f +#define ACX_CONT_WIND_MAX 0x03ff0000 + +#define REF_FREQ_19_2 0 +#define REF_FREQ_26_0 1 +#define REF_FREQ_38_4 2 +#define REF_FREQ_40_0 3 +#define REF_FREQ_33_6 4 +#define REF_FREQ_NUM 5 + +#define LUT_PARAM_INTEGER_DIVIDER 0 +#define LUT_PARAM_FRACTIONAL_DIVIDER 1 +#define LUT_PARAM_ATTN_BB 2 +#define LUT_PARAM_ALPHA_BB 3 +#define LUT_PARAM_STOP_TIME_BB 4 +#define LUT_PARAM_BB_PLL_LOOP_FILTER 5 +#define LUT_PARAM_NUM 6 + +#define WL12XX_EEPROMLESS_IND (WL12XX_SCR_PAD4) +#define USE_EEPROM 0 +#define NVS_DATA_BUNDARY_ALIGNMENT 4 + +/* Firmware image header size */ +#define FW_HDR_SIZE 8 + +/****************************************************************************** + + CHANNELS, BAND & REG DOMAINS definitions + +******************************************************************************/ + +#define SHORT_PREAMBLE_BIT BIT(0) /* CCK or Barker depending on the rate */ +#define OFDM_RATE_BIT BIT(6) +#define PBCC_RATE_BIT BIT(7) + +enum { + CCK_LONG = 0, + CCK_SHORT = SHORT_PREAMBLE_BIT, + PBCC_LONG = PBCC_RATE_BIT, + PBCC_SHORT = PBCC_RATE_BIT | SHORT_PREAMBLE_BIT, + OFDM = OFDM_RATE_BIT +}; + +/****************************************************************************** + +Transmit-Descriptor RATE-SET field definitions... + +Define a new "Rate-Set" for TX path that incorporates the +Rate & Modulation info into a single 16-bit field. + +TxdRateSet_t: +b15 - Indicates Preamble type (1=SHORT, 0=LONG). + Notes: + Must be LONG (0) for 1Mbps rate. + Does not apply (set to 0) for RevG-OFDM rates. +b14 - Indicates PBCC encoding (1=PBCC, 0=not). + Notes: + Does not apply (set to 0) for rates 1 and 2 Mbps. + Does not apply (set to 0) for RevG-OFDM rates. +b13 - Unused (set to 0). +b12-b0 - Supported Rate indicator bits as defined below. + +******************************************************************************/ + +#define OCP_CMD_LOOP 32 +#define OCP_CMD_WRITE 0x1 +#define OCP_CMD_READ 0x2 +#define OCP_READY_MASK BIT(18) +#define OCP_STATUS_MASK (BIT(16) | BIT(17)) +#define OCP_STATUS_NO_RESP 0x00000 +#define OCP_STATUS_OK 0x10000 +#define OCP_STATUS_REQ_FAILED 0x20000 +#define OCP_STATUS_RESP_ERROR 0x30000 + +#define OCP_REG_POLARITY 0x0064 +#define OCP_REG_CLK_TYPE 0x0448 +#define OCP_REG_CLK_POLARITY 0x0cb2 +#define OCP_REG_CLK_PULL 0x0cb4 + +#define POLARITY_LOW BIT(1) +#define NO_PULL (BIT(14) | BIT(15)) + +#define FREF_CLK_TYPE_BITS 0xfffffe7f +#define CLK_REQ_PRCM 0x100 +#define FREF_CLK_POLARITY_BITS 0xfffff8ff +#define CLK_REQ_OUTN_SEL 0x700 + +#define WU_COUNTER_PAUSE_VAL 0x3FF + +/* PLL configuration algorithm for wl128x */ +#define SYS_CLK_CFG_REG 0x2200 +/* Bit[0] - 0-TCXO, 1-FREF */ +#define MCS_PLL_CLK_SEL_FREF BIT(0) +/* Bit[3:2] - 01-TCXO, 10-FREF */ +#define WL_CLK_REQ_TYPE_FREF BIT(3) +#define WL_CLK_REQ_TYPE_PG2 (BIT(3) | BIT(2)) +/* Bit[4] - 0-TCXO, 1-FREF */ +#define PRCM_CM_EN_MUX_WLAN_FREF BIT(4) + +#define TCXO_ILOAD_INT_REG 0x2264 +#define TCXO_CLK_DETECT_REG 0x2266 + +#define TCXO_DET_FAILED BIT(4) + +#define FREF_ILOAD_INT_REG 0x2084 +#define FREF_CLK_DETECT_REG 0x2086 +#define FREF_CLK_DETECT_FAIL BIT(4) + +/* Use this reg for masking during driver access */ +#define WL_SPARE_REG 0x2320 +#define WL_SPARE_VAL BIT(2) +/* Bit[6:5:3] - mask wl write SYS_CLK_CFG[8:5:2:4] */ +#define WL_SPARE_MASK_8526 (BIT(6) | BIT(5) | BIT(3)) + +#define PLL_LOCK_COUNTERS_REG 0xD8C +#define PLL_LOCK_COUNTERS_COEX 0x0F +#define PLL_LOCK_COUNTERS_MCS 0xF0 +#define MCS_PLL_OVERRIDE_REG 0xD90 +#define MCS_PLL_CONFIG_REG 0xD92 +#define MCS_SEL_IN_FREQ_MASK 0x0070 +#define MCS_SEL_IN_FREQ_SHIFT 4 +#define MCS_PLL_CONFIG_REG_VAL 0x73 +#define MCS_PLL_ENABLE_HP (BIT(0) | BIT(1)) + +#define MCS_PLL_M_REG 0xD94 +#define MCS_PLL_N_REG 0xD96 +#define MCS_PLL_M_REG_VAL 0xC8 +#define MCS_PLL_N_REG_VAL 0x07 + +#define SDIO_IO_DS 0xd14 + +/* SDIO/wSPI DS configuration values */ +enum { + HCI_IO_DS_8MA = 0, + HCI_IO_DS_4MA = 1, /* default */ + HCI_IO_DS_6MA = 2, + HCI_IO_DS_2MA = 3, +}; + +/* end PLL configuration algorithm for wl128x */ + +/* + * Host Command Interrupt. Setting this bit masks + * the interrupt that the host issues to inform + * the FW that it has sent a command + * to the Wlan hardware Command Mailbox. + */ +#define WL12XX_INTR_TRIG_CMD BIT(0) + +/* + * Host Event Acknowlegde Interrupt. The host + * sets this bit to acknowledge that it received + * the unsolicited information from the event + * mailbox. + */ +#define WL12XX_INTR_TRIG_EVENT_ACK BIT(1) + +/*=============================================== + HI_CFG Interface Configuration Register Values + ------------------------------------------ + ===============================================*/ +#define HI_CFG_UART_ENABLE 0x00000004 +#define HI_CFG_RST232_ENABLE 0x00000008 +#define HI_CFG_CLOCK_REQ_SELECT 0x00000010 +#define HI_CFG_HOST_INT_ENABLE 0x00000020 +#define HI_CFG_VLYNQ_OUTPUT_ENABLE 0x00000040 +#define HI_CFG_HOST_INT_ACTIVE_LOW 0x00000080 +#define HI_CFG_UART_TX_OUT_GPIO_15 0x00000100 +#define HI_CFG_UART_TX_OUT_GPIO_14 0x00000200 +#define HI_CFG_UART_TX_OUT_GPIO_7 0x00000400 + +#define HI_CFG_DEF_VAL \ + (HI_CFG_UART_ENABLE | \ + HI_CFG_RST232_ENABLE | \ + HI_CFG_CLOCK_REQ_SELECT | \ + HI_CFG_HOST_INT_ENABLE) + +#define WL127X_REG_FUSE_DATA_2_1 0x050a +#define WL128X_REG_FUSE_DATA_2_1 0x2152 +#define PG_VER_MASK 0x3c +#define PG_VER_OFFSET 2 + +#define WL127X_PG_MAJOR_VER_MASK 0x3 +#define WL127X_PG_MAJOR_VER_OFFSET 0x0 +#define WL127X_PG_MINOR_VER_MASK 0xc +#define WL127X_PG_MINOR_VER_OFFSET 0x2 + +#define WL128X_PG_MAJOR_VER_MASK 0xc +#define WL128X_PG_MAJOR_VER_OFFSET 0x2 +#define WL128X_PG_MINOR_VER_MASK 0x3 +#define WL128X_PG_MINOR_VER_OFFSET 0x0 + +#define WL127X_PG_GET_MAJOR(pg_ver) ((pg_ver & WL127X_PG_MAJOR_VER_MASK) >> \ + WL127X_PG_MAJOR_VER_OFFSET) +#define WL127X_PG_GET_MINOR(pg_ver) ((pg_ver & WL127X_PG_MINOR_VER_MASK) >> \ + WL127X_PG_MINOR_VER_OFFSET) +#define WL128X_PG_GET_MAJOR(pg_ver) ((pg_ver & WL128X_PG_MAJOR_VER_MASK) >> \ + WL128X_PG_MAJOR_VER_OFFSET) +#define WL128X_PG_GET_MINOR(pg_ver) ((pg_ver & WL128X_PG_MINOR_VER_MASK) >> \ + WL128X_PG_MINOR_VER_OFFSET) + +#define WL12XX_REG_FUSE_BD_ADDR_1 0x00310eb4 +#define WL12XX_REG_FUSE_BD_ADDR_2 0x00310eb8 + +#endif -- cgit v1.2.3