Postfix Small/Home Office Hints and TipsPostfix Small/Home Office Hints and TipsThis document combines hints and tips for "small office/home office" applications into one document so that they are easier to find. The text describes the mail sending side only. If your machine does not receive mail directly (i.e. it does not have its own Internet domain name and its own fixed IP address), then you will need a solution such as "fetchmail", which is outside the scope of the Postfix documentation.
Selected topics from the STANDARD_CONFIGURATION_README document:
Selected topics from the SASL_README document:
See the SASL_README and STANDARD_CONFIGURATION_README documents for further information on these topics.
Postfix should work out of the box without change on a stand-alone machine that has direct Internet access. At least, that is how Postfix installs when you download the Postfix source code via http://www.postfix.org/.
You can use the command "postconf -n" to find out what settings are overruled by your main.cf. Besides a few pathname settings, few parameters should be set on a stand-alone box, beyond what is covered in the BASIC_CONFIGURATION_README document:
/etc/postfix/main.cf:
# Optional: send mail as user@domainname instead of user@hostname.
#myorigin = $mydomain
# Optional: specify NAT/proxy external address.
#proxy_interfaces = 1.2.3.4
# Alternative 1: don't relay mail from other hosts.
mynetworks_style = host
relay_domains =
# Alternative 2: relay mail from local clients only.
# mynetworks = 192.168.1.0/28
# relay_domains =
See also the section "Postfix on hosts without a real Internet hostname" if this is applicable to your configuration.
This section is for hosts that don't have their own Internet hostname. Typically these are systems that get a dynamic IP address via DHCP or via dialup. Postfix will let you send and receive mail just fine between accounts on a machine with a fantasy name. However, you cannot use a fantasy hostname in your email address when sending mail into the Internet, because no-one would be able to reply to your mail. In fact, more and more sites refuse mail addresses with non-existent domain names.
Note: the following information is Postfix version dependent. To find out what Postfix version you have, execute the command "postconf mail_version".
Postfix 2.2 uses the generic(5) address mapping to replace local fantasy email addresses by valid Internet addresses. This mapping happens ONLY when mail leaves the machine; not when you send mail between users on the same machine.
The following example presents additional configuration. You need to combine this with basic configuration information as discussed the first half of this document.
1 /etc/postfix/main.cf: 2 smtp_generic_maps = hash:/etc/postfix/generic 3 4 /etc/postfix/generic: 5 his@localdomain.local hisaccount@hisisp.example 6 her@localdomain.local heraccount@herisp.example 7 @localdomain.local hisaccount+local@hisisp.example
When mail is sent to a remote host via SMTP:
Line 5 replaces his@localdomain.local by his ISP mail address,
Line 6 replaces her@localdomain.local by her ISP mail address, and
Line 7 replaces other local addresses by his ISP account, with an address extension of +local (this example assumes that the ISP supports "+" style address extensions).
Specify dbm instead of hash if your system uses dbm files instead of db files. To find out what lookup tables Postfix supports, use the command "postconf -m".
Execute the command "postmap /etc/postfix/generic" whenever you change the generic table.
The solution with older Postfix systems is to use valid Internet addresses where possible, and to let Postfix map valid Internet addresses to local fantasy addresses. With this, you can send mail to the Internet and to local fantasy addresses, including mail to local fantasy addresses that don't have a valid Internet address of their own.
The following example presents additional configuration. You need to combine this with basic configuration information as discussed the first half of this document.
1 /etc/postfix/main.cf: 2 myhostname = hostname.localdomain 3 mydomain = localdomain 4 5 canonical_maps = hash:/etc/postfix/canonical 6 7 virtual_alias_maps = hash:/etc/postfix/virtual 8 9 /etc/postfix/canonical: 10 your-login-name your-account@your-isp.com 11 12 /etc/postfix/virtual: 13 your-account@your-isp.com your-login-name
Translation:
Lines 2-3: Substitute your fantasy hostname here. Do not use a domain name that is already in use by real organizations on the Internet. See RFC 2606 for examples of domain names that are guaranteed not to be owned by anyone.
Lines 5, 9, 10: This provides the mapping from "your-login-name@hostname.localdomain" to "your-account@your-isp.com". This part is required.
Lines 7, 12, 13: Deliver mail for "your-account@your-isp.com" locally, instead of sending it to the ISP. This part is not required but is convenient.
Specify dbm instead of hash if your system uses dbm files instead of db files. To find out what lookup tables Postfix supports, use the command "postconf -m".
Execute the command "postmap /etc/postfix/canonical" whenever you change the canonical table.
Execute the command "postmap /etc/postfix/virtual" whenever you change the virtual table.
This section shows a typical scenario where the Postfix SMTP client sends all messages via a mail gateway server that requires SASL authentication.
Trouble solving tips:
If your SASL logins fail with "SASL authentication failure: No worthy mechs found" in the mail logfile, then see the section "Postfix SMTP/LMTP client policy - SASL mechanism properties".
For a solution to a more obscure class of SASL authentication failures, see "Postfix SMTP/LMTP client policy - SASL mechanism names".
To make the example more readable we introduce it in two parts. The first part takes care of the basic configuration, while the second part sets up the username/password information.
/etc/postfix/main.cf:
smtp_sasl_auth_enable = yes
smtp_tls_security_level = encrypt
smtp_sasl_tls_security_options = noanonymous
relayhost = [mail.isp.example]
# Alternative form:
# relayhost = [mail.isp.example]:submission
smtp_sasl_password_maps = hash:/etc/postfix/sasl_passwd
The smtp_sasl_auth_enable setting enables
client-side authentication. We will configure the client's username
and password information in the second part of the example.
The smtp_tls_security_level setting ensures
that the connection to the remote smtp server will be encrypted, and
smtp_sasl_tls_security_options removes the prohibition on
plaintext passwords.
The relayhost setting forces the Postfix SMTP
to send all remote messages to the specified mail server instead
of trying to deliver them directly to their destination.
In the relayhost setting, the "["
and "]" prevent the Postfix SMTP client from looking
up MX (mail exchanger) records for the enclosed name.
The relayhost destination may also specify a
non-default TCP port. For example, the alternative form
[mail.isp.example]:submission tells Postfix to connect
to TCP network port 587, which is reserved for email client
applications.
The Postfix SMTP client is compatible with SMTP servers
that use the non-standard "AUTH=method...."
syntax in response to the EHLO command; this requires no additional
Postfix client configuration.
The Postfix SMTP client does not support the obsolete
"wrappermode" protocol, which uses TCP port 465 on the
SMTP server. See TLS_README for a solution that uses the
stunnel command.
With the smtp_sasl_password_maps parameter,
we configure the Postfix SMTP client to send username and password
information to the mail gateway server. As discussed in the next
section, the Postfix SMTP client supports multiple ISP accounts.
For this reason the username and password are stored in a table
that contains one username/password combination for each mail gateway
server.
/etc/postfix/sasl_passwd:
# destination credentials
[mail.isp.example] username:password
# Alternative form:
# [mail.isp.example]:submission username:password
ImportantKeep the SASL client password file in
/etc/postfix, and make the file read+write only forrootto protect the username/password combinations against other users. The Postfix SMTP client will still be able to read the SASL client passwords. It opens the file as userrootbefore it drops privileges, and before entering an optional chroot jail.
Use the postmap command whenever you
change the /etc/postfix/sasl_passwd file.
If you specify the "[" and "]"
in the relayhost destination, then you must use the
same form in the smtp_sasl_password_maps file.
If you specify a non-default TCP Port (such as
":submission" or ":587") in the
relayhost destination, then you must use the same form
in the smtp_sasl_password_maps file.
Postfix supports different ISP accounts for different sender addresses (version 2.3 and later). This can be useful when one person uses the same machine for work and for personal use, or when people with different ISP accounts share the same Postfix server.
To make this possible, Postfix supports per-sender SASL passwords
and per-sender relay hosts. In the example below, the Postfix SMTP
client will search the SASL password file by sender address before
it searches that same file by destination. Likewise, the Postfix
trivial-rewrite(8) daemon will search the per-sender relayhost file,
and use the default relayhost setting only as a final
resort.
/etc/postfix/main.cf:
smtp_sender_dependent_authentication = yes
sender_dependent_relayhost_maps = hash:/etc/postfix/sender_relay
smtp_sasl_auth_enable = yes
smtp_sasl_password_maps = hash:/etc/postfix/sasl_passwd
relayhost = [mail.isp.example]
# Alternative form:
# relayhost = [mail.isp.example]:submission
/etc/postfix/sasl_passwd:
# Per-sender authentication; see also /etc/postfix/sender_relay.
user1@example.com username1:password1
user2@example.net username2:password2
# Login information for the default relayhost.
[mail.isp.example] username:password
# Alternative form:
# [mail.isp.example]:submission username:password
/etc/postfix/sender_relay:
# Per-sender provider; see also /etc/postfix/sasl_passwd.
user1@example.com [mail.example.com]:submission
user2@example.net [mail.example.net]
If you are creative, then you can try to combine the two tables into one single MySQL database, and configure different Postfix queries to extract the appropriate information.
Specify dbm instead of hash if your system uses dbm files instead of db files. To find out what lookup tables Postfix supports, use the command "postconf -m".
Execute the command "postmap /etc/postfix/sasl_passwd" whenever you change the sasl_passwd table.
Execute the command "postmap /etc/postfix/sender_relay" whenever you change the sender_relay table.