diff options
Diffstat (limited to '')
| -rw-r--r-- | doc/rados/operations/balancer.rst | 221 |
1 files changed, 221 insertions, 0 deletions
diff --git a/doc/rados/operations/balancer.rst b/doc/rados/operations/balancer.rst new file mode 100644 index 000000000..aa4eab93c --- /dev/null +++ b/doc/rados/operations/balancer.rst @@ -0,0 +1,221 @@ +.. _balancer: + +Balancer Module +======================= + +The *balancer* can optimize the allocation of placement groups (PGs) across +OSDs in order to achieve a balanced distribution. The balancer can operate +either automatically or in a supervised fashion. + + +Status +------ + +To check the current status of the balancer, run the following command: + + .. prompt:: bash $ + + ceph balancer status + + +Automatic balancing +------------------- + +When the balancer is in ``upmap`` mode, the automatic balancing feature is +enabled by default. For more details, see :ref:`upmap`. To disable the +balancer, run the following command: + + .. prompt:: bash $ + + ceph balancer off + +The balancer mode can be changed from ``upmap`` mode to ``crush-compat`` mode. +``crush-compat`` mode is backward compatible with older clients. In +``crush-compat`` mode, the balancer automatically makes small changes to the +data distribution in order to ensure that OSDs are utilized equally. + + +Throttling +---------- + +If the cluster is degraded (that is, if an OSD has failed and the system hasn't +healed itself yet), then the balancer will not make any adjustments to the PG +distribution. + +When the cluster is healthy, the balancer will incrementally move a small +fraction of unbalanced PGs in order to improve distribution. This fraction +will not exceed a certain threshold that defaults to 5%. To adjust this +``target_max_misplaced_ratio`` threshold setting, run the following command: + + .. prompt:: bash $ + + ceph config set mgr target_max_misplaced_ratio .07 # 7% + +The balancer sleeps between runs. To set the number of seconds for this +interval of sleep, run the following command: + + .. prompt:: bash $ + + ceph config set mgr mgr/balancer/sleep_interval 60 + +To set the time of day (in HHMM format) at which automatic balancing begins, +run the following command: + + .. prompt:: bash $ + + ceph config set mgr mgr/balancer/begin_time 0000 + +To set the time of day (in HHMM format) at which automatic balancing ends, run +the following command: + + .. prompt:: bash $ + + ceph config set mgr mgr/balancer/end_time 2359 + +Automatic balancing can be restricted to certain days of the week. To restrict +it to a specific day of the week or later (as with crontab, ``0`` is Sunday, +``1`` is Monday, and so on), run the following command: + + .. prompt:: bash $ + + ceph config set mgr mgr/balancer/begin_weekday 0 + +To restrict automatic balancing to a specific day of the week or earlier +(again, ``0`` is Sunday, ``1`` is Monday, and so on), run the following +command: + + .. prompt:: bash $ + + ceph config set mgr mgr/balancer/end_weekday 6 + +Automatic balancing can be restricted to certain pools. By default, the value +of this setting is an empty string, so that all pools are automatically +balanced. To restrict automatic balancing to specific pools, retrieve their +numeric pool IDs (by running the :command:`ceph osd pool ls detail` command), +and then run the following command: + + .. prompt:: bash $ + + ceph config set mgr mgr/balancer/pool_ids 1,2,3 + + +Modes +----- + +There are two supported balancer modes: + +#. **crush-compat**. This mode uses the compat weight-set feature (introduced + in Luminous) to manage an alternative set of weights for devices in the + CRUSH hierarchy. When the balancer is operating in this mode, the normal + weights should remain set to the size of the device in order to reflect the + target amount of data intended to be stored on the device. The balancer will + then optimize the weight-set values, adjusting them up or down in small + increments, in order to achieve a distribution that matches the target + distribution as closely as possible. (Because PG placement is a pseudorandom + process, it is subject to a natural amount of variation; optimizing the + weights serves to counteract that natural variation.) + + Note that this mode is *fully backward compatible* with older clients: when + an OSD Map and CRUSH map are shared with older clients, Ceph presents the + optimized weights as the "real" weights. + + The primary limitation of this mode is that the balancer cannot handle + multiple CRUSH hierarchies with different placement rules if the subtrees of + the hierarchy share any OSDs. (Such sharing of OSDs is not typical and, + because of the difficulty of managing the space utilization on the shared + OSDs, is generally not recommended.) + +#. **upmap**. In Luminous and later releases, the OSDMap can store explicit + mappings for individual OSDs as exceptions to the normal CRUSH placement + calculation. These ``upmap`` entries provide fine-grained control over the + PG mapping. This balancer mode optimizes the placement of individual PGs in + order to achieve a balanced distribution. In most cases, the resulting + distribution is nearly perfect: that is, there is an equal number of PGs on + each OSD (±1 PG, since the total number might not divide evenly). + + To use ``upmap``, all clients must be Luminous or newer. + +The default mode is ``upmap``. The mode can be changed to ``crush-compat`` by +running the following command: + + .. prompt:: bash $ + + ceph balancer mode crush-compat + +Supervised optimization +----------------------- + +Supervised use of the balancer can be understood in terms of three distinct +phases: + +#. building a plan +#. evaluating the quality of the data distribution, either for the current PG + distribution or for the PG distribution that would result after executing a + plan +#. executing the plan + +To evaluate the current distribution, run the following command: + + .. prompt:: bash $ + + ceph balancer eval + +To evaluate the distribution for a single pool, run the following command: + + .. prompt:: bash $ + + ceph balancer eval <pool-name> + +To see the evaluation in greater detail, run the following command: + + .. prompt:: bash $ + + ceph balancer eval-verbose ... + +To instruct the balancer to generate a plan (using the currently configured +mode), make up a name (any useful identifying string) for the plan, and run the +following command: + + .. prompt:: bash $ + + ceph balancer optimize <plan-name> + +To see the contents of a plan, run the following command: + + .. prompt:: bash $ + + ceph balancer show <plan-name> + +To display all plans, run the following command: + + .. prompt:: bash $ + + ceph balancer ls + +To discard an old plan, run the following command: + + .. prompt:: bash $ + + ceph balancer rm <plan-name> + +To see currently recorded plans, examine the output of the following status +command: + + .. prompt:: bash $ + + ceph balancer status + +To evaluate the distribution that would result from executing a specific plan, +run the following command: + + .. prompt:: bash $ + + ceph balancer eval <plan-name> + +If a plan is expected to improve the distribution (that is, the plan's score is +lower than the current cluster state's score), you can execute that plan by +running the following command: + + .. prompt:: bash $ + + ceph balancer execute <plan-name> |