================================= Network Configuration Reference ================================= Network configuration is critical for building a high performance :term:`Ceph Storage Cluster`. The Ceph Storage Cluster does not perform request routing or dispatching on behalf of the :term:`Ceph Client`. Instead, Ceph Clients make requests directly to Ceph OSD Daemons. Ceph OSD Daemons perform data replication on behalf of Ceph Clients, which means replication and other factors impose additional loads on Ceph Storage Cluster networks. Our Quick Start configurations provide a trivial Ceph configuration file that sets monitor IP addresses and daemon host names only. Unless you specify a cluster network, Ceph assumes a single "public" network. Ceph functions just fine with a public network only, but you may see significant performance improvement with a second "cluster" network in a large cluster. It is possible to run a Ceph Storage Cluster with two networks: a public (client, front-side) network and a cluster (private, replication, back-side) network. However, this approach complicates network configuration (both hardware and software) and does not usually have a significant impact on overall performance. For this reason, we recommend that for resilience and capacity dual-NIC systems either active/active bond these interfaces or implement a layer 3 multipath strategy with eg. FRR. If, despite the complexity, one still wishes to use two networks, each :term:`Ceph Node` will need to have more than one network interface or VLAN. See `Hardware Recommendations - Networks`_ for additional details. .. ditaa:: +-------------+ | Ceph Client | +----*--*-----+ | ^ Request | : Response v | /----------------------------------*--*-------------------------------------\ | Public Network | \---*--*------------*--*-------------*--*------------*--*------------*--*---/ ^ ^ ^ ^ ^ ^ ^ ^ ^ ^ | | | | | | | | | | | : | : | : | : | : v v v v v v v v v v +---*--*---+ +---*--*---+ +---*--*---+ +---*--*---+ +---*--*---+ | Ceph MON | | Ceph MDS | | Ceph OSD | | Ceph OSD | | Ceph OSD | +----------+ +----------+ +---*--*---+ +---*--*---+ +---*--*---+ ^ ^ ^ ^ ^ ^ The cluster network relieves | | | | | | OSD replication and heartbeat | : | : | : traffic from the public network. v v v v v v /------------------------------------*--*------------*--*------------*--*---\ | cCCC Cluster Network | \---------------------------------------------------------------------------/ IP Tables ========= By default, daemons `bind`_ to ports within the ``6800:7300`` range. You may configure this range at your discretion. Before configuring your IP tables, check the default ``iptables`` configuration. .. prompt:: bash $ sudo iptables -L Some Linux distributions include rules that reject all inbound requests except SSH from all network interfaces. For example:: REJECT all -- anywhere anywhere reject-with icmp-host-prohibited You will need to delete these rules on both your public and cluster networks initially, and replace them with appropriate rules when you are ready to harden the ports on your Ceph Nodes. Monitor IP Tables ----------------- Ceph Monitors listen on ports ``3300`` and ``6789`` by default. Additionally, Ceph Monitors always operate on the public network. When you add the rule using the example below, make sure you replace ``{iface}`` with the public network interface (e.g., ``eth0``, ``eth1``, etc.), ``{ip-address}`` with the IP address of the public network and ``{netmask}`` with the netmask for the public network. : .. prompt:: bash $ sudo iptables -A INPUT -i {iface} -p tcp -s {ip-address}/{netmask} --dport 6789 -j ACCEPT MDS and Manager IP Tables ------------------------- A :term:`Ceph Metadata Server` or :term:`Ceph Manager` listens on the first available port on the public network beginning at port 6800. Note that this behavior is not deterministic, so if you are running more than one OSD or MDS on the same host, or if you restart the daemons within a short window of time, the daemons will bind to higher ports. You should open the entire 6800-7300 range by default. When you add the rule using the example below, make sure you replace ``{iface}`` with the public network interface (e.g., ``eth0``, ``eth1``, etc.), ``{ip-address}`` with the IP address of the public network and ``{netmask}`` with the netmask of the public network. For example: .. prompt:: bash $ sudo iptables -A INPUT -i {iface} -m multiport -p tcp -s {ip-address}/{netmask} --dports 6800:7300 -j ACCEPT OSD IP Tables ------------- By default, Ceph OSD Daemons `bind`_ to the first available ports on a Ceph Node beginning at port 6800. Note that this behavior is not deterministic, so if you are running more than one OSD or MDS on the same host, or if you restart the daemons within a short window of time, the daemons will bind to higher ports. Each Ceph OSD Daemon on a Ceph Node may use up to four ports: #. One for talking to clients and monitors. #. One for sending data to other OSDs. #. Two for heartbeating on each interface. .. ditaa:: /---------------\ | OSD | | +---+----------------+-----------+ | | Clients & Monitors | Heartbeat | | +---+----------------+-----------+ | | | +---+----------------+-----------+ | | Data Replication | Heartbeat | | +---+----------------+-----------+ | cCCC | \---------------/ When a daemon fails and restarts without letting go of the port, the restarted daemon will bind to a new port. You should open the entire 6800-7300 port range to handle this possibility. If you set up separate public and cluster networks, you must add rules for both the public network and the cluster network, because clients will connect using the public network and other Ceph OSD Daemons will connect using the cluster network. When you add the rule using the example below, make sure you replace ``{iface}`` with the network interface (e.g., ``eth0``, ``eth1``, etc.), ``{ip-address}`` with the IP address and ``{netmask}`` with the netmask of the public or cluster network. For example: .. prompt:: bash $ sudo iptables -A INPUT -i {iface} -m multiport -p tcp -s {ip-address}/{netmask} --dports 6800:7300 -j ACCEPT .. tip:: If you run Ceph Metadata Servers on the same Ceph Node as the Ceph OSD Daemons, you can consolidate the public network configuration step. Ceph Networks ============= To configure Ceph networks, you must add a network configuration to the ``[global]`` section of the configuration file. Our 5-minute Quick Start provides a trivial Ceph configuration file that assumes one public network with client and server on the same network and subnet. Ceph functions just fine with a public network only. However, Ceph allows you to establish much more specific criteria, including multiple IP network and subnet masks for your public network. You can also establish a separate cluster network to handle OSD heartbeat, object replication and recovery traffic. Don't confuse the IP addresses you set in your configuration with the public-facing IP addresses network clients may use to access your service. Typical internal IP networks are often ``192.168.0.0`` or ``10.0.0.0``. .. tip:: If you specify more than one IP address and subnet mask for either the public or the cluster network, the subnets within the network must be capable of routing to each other. Additionally, make sure you include each IP address/subnet in your IP tables and open ports for them as necessary. .. note:: Ceph uses `CIDR`_ notation for subnets (e.g., ``10.0.0.0/24``). When you have configured your networks, you may restart your cluster or restart each daemon. Ceph daemons bind dynamically, so you do not have to restart the entire cluster at once if you change your network configuration. Public Network -------------- To configure a public network, add the following option to the ``[global]`` section of your Ceph configuration file. .. code-block:: ini [global] # ... elided configuration public_network = {public-network/netmask} .. _cluster-network: Cluster Network --------------- If you declare a cluster network, OSDs will route heartbeat, object replication and recovery traffic over the cluster network. This may improve performance compared to using a single network. To configure a cluster network, add the following option to the ``[global]`` section of your Ceph configuration file. .. code-block:: ini [global] # ... elided configuration cluster_network = {cluster-network/netmask} We prefer that the cluster network is **NOT** reachable from the public network or the Internet for added security. IPv4/IPv6 Dual Stack Mode ------------------------- If you want to run in an IPv4/IPv6 dual stack mode and want to define your public and/or cluster networks, then you need to specify both your IPv4 and IPv6 networks for each: .. code-block:: ini [global] # ... elided configuration public_network = {IPv4 public-network/netmask}, {IPv6 public-network/netmask} This is so that Ceph can find a valid IP address for both address families. If you want just an IPv4 or an IPv6 stack environment, then make sure you set the `ms bind` options correctly. .. note:: Binding to IPv4 is enabled by default, so if you just add the option to bind to IPv6 you'll actually put yourself into dual stack mode. If you want just IPv6, then disable IPv4 and enable IPv6. See `Bind`_ below. Ceph Daemons ============ Monitor daemons are each configured to bind to a specific IP address. These addresses are normally configured by your deployment tool. Other components in the Ceph cluster discover the monitors via the ``mon host`` configuration option, normally specified in the ``[global]`` section of the ``ceph.conf`` file. .. code-block:: ini [global] mon_host = 10.0.0.2, 10.0.0.3, 10.0.0.4 The ``mon_host`` value can be a list of IP addresses or a name that is looked up via DNS. In the case of a DNS name with multiple A or AAAA records, all records are probed in order to discover a monitor. Once one monitor is reached, all other current monitors are discovered, so the ``mon host`` configuration option only needs to be sufficiently up to date such that a client can reach one monitor that is currently online. The MGR, OSD, and MDS daemons will bind to any available address and do not require any special configuration. However, it is possible to specify a specific IP address for them to bind to with the ``public addr`` (and/or, in the case of OSD daemons, the ``cluster addr``) configuration option. For example, .. code-block:: ini [osd.0] public_addr = {host-public-ip-address} cluster_addr = {host-cluster-ip-address} .. topic:: One NIC OSD in a Two Network Cluster Generally, we do not recommend deploying an OSD host with a single network interface in a cluster with two networks. However, you may accomplish this by forcing the OSD host to operate on the public network by adding a ``public_addr`` entry to the ``[osd.n]`` section of the Ceph configuration file, where ``n`` refers to the ID of the OSD with one network interface. Additionally, the public network and cluster network must be able to route traffic to each other, which we don't recommend for security reasons. Network Config Settings ======================= Network configuration settings are not required. Ceph assumes a public network with all hosts operating on it unless you specifically configure a cluster network. Public Network -------------- The public network configuration allows you specifically define IP addresses and subnets for the public network. You may specifically assign static IP addresses or override ``public_network`` settings using the ``public_addr`` setting for a specific daemon. .. confval:: public_network .. confval:: public_addr Cluster Network --------------- The cluster network configuration allows you to declare a cluster network, and specifically define IP addresses and subnets for the cluster network. You may specifically assign static IP addresses or override ``cluster_network`` settings using the ``cluster_addr`` setting for specific OSD daemons. .. confval:: cluster_network .. confval:: cluster_addr Bind ---- Bind settings set the default port ranges Ceph OSD and MDS daemons use. The default range is ``6800:7300``. Ensure that your `IP Tables`_ configuration allows you to use the configured port range. You may also enable Ceph daemons to bind to IPv6 addresses instead of IPv4 addresses. .. confval:: ms_bind_port_min .. confval:: ms_bind_port_max .. confval:: ms_bind_ipv4 .. confval:: ms_bind_ipv6 .. confval:: public_bind_addr TCP --- Ceph disables TCP buffering by default. .. confval:: ms_tcp_nodelay .. confval:: ms_tcp_rcvbuf General Settings ---------------- .. confval:: ms_type .. confval:: ms_async_op_threads .. confval:: ms_initial_backoff .. confval:: ms_max_backoff .. confval:: ms_die_on_bad_msg .. confval:: ms_dispatch_throttle_bytes .. confval:: ms_inject_socket_failures .. _Scalability and High Availability: ../../../architecture#scalability-and-high-availability .. _Hardware Recommendations - Networks: ../../../start/hardware-recommendations#networks .. _hardware recommendations: ../../../start/hardware-recommendations .. _Monitor / OSD Interaction: ../mon-osd-interaction .. _Message Signatures: ../auth-config-ref#signatures .. _CIDR: https://en.wikipedia.org/wiki/Classless_Inter-Domain_Routing .. _Nagle's Algorithm: https://en.wikipedia.org/wiki/Nagle's_algorithm