Merging upstream version 20240610.

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 0 insertions, 233 deletions

diff --git a/carl9170fw/carlfw/Kconfig b/carl9170fw/carlfw/Kconfig
deleted file mode 100644
index f42268c..0000000
--- a/carl9170fw/carlfw/Kconfig
+++ /dev/null
@@ -1,233 +0,0 @@
-menu "General"
-
-config CARL9170FW_RELEASE_VERSION
-	int
-	default 1
-
-menu "Selectable Hardware Options"
-
-choice
-	prompt "Receiver Max. Frame Length"
-	default CARL9170FW_RX_FRAME_LEN_8192
-
-	config CARL9170FW_RX_FRAME_LEN_4096
-		bool "4096"
-
-	config CARL9170FW_RX_FRAME_LEN_8192
-		bool "8192"
-
-	config CARL9170FW_RX_FRAME_LEN_16384
-		bool "16384"
-
-	config CARL9170FW_RX_FRAME_LEN_32768
-		bool "32768"
-
-endchoice
-
-config CARL9170FW_RX_FRAME_LEN
-	int
-	default 4096 if CARL9170FW_RX_FRAME_LEN_4096
-	default 8192 if CARL9170FW_RX_FRAME_LEN_8192
-	default 16384 if CARL9170FW_RX_FRAME_LEN_16384
-	default 32768 if CARL9170FW_RX_FRAME_LEN_32768
-
-config CARL9170FW_GPIO_INTERRUPT
-	def_bool y
-	prompt "GPIO Software Interrupt"
-	---help---
-	 When this option is enabled, the firmware will poll the GPIO
-	 registers and reports to the driver whenever the GPIO state
-	 has changed from a previous state.
-
-	 Note: This feature is necessary to monitor the WPS button,
-	       if you have one on your device, then say Y.
-
-config CARL9170FW_SECURITY_ENGINE
-	def_bool y
-	prompt "Support Hardware Crypto Engine"
-	---help---
-	 This options controls if the firmware will allow the driver
-	 to program the security engine / CAM through a firmware
-	 interface.
-
-	 Say Y. Unless you want to do the en- and decryption for
-	 CCMP(AES), TKIP/WEP(RC4) in the application anyway.
-
-config CARL9170FW_RADIO_FUNCTIONS
-	def_bool y
-	prompt "Enable Firmware-supported Radio/RF functions"
-	---help---
-	 Some PHY/RF functions (e.g.: AGC and Noise calibration) need
-	 to be done in the firmware.
-
-	 Say Y, unless you really don't need the Radio/RF for
-	 your project.
-
-endmenu
-
-menu "802.11 Firmware Features"
-
-config CARL9170FW_CAB_QUEUE
-	def_bool y
-	prompt "Support software-based Content after Beacon Queue"
-	---help---
-	 This (software) queue is used to send any broad-/multi-cast buffered
-	 frames after the next DTIM beacon.
-
-	 This feature is required for Accesspoint mode operation.
-
-	 Say Y.
-
-endmenu
-
-source "carlfw/usb/Kconfig"
-
-menu "Experimental, Unstable & Testing Extensions"
-
-config CARL9170FW_PRINTF
-	def_bool y
-	prompt "Advanced printf"
-	depends on CARL9170FW_DEBUG_UART || CARL9170FW_DEBUG_USB
-	---help---
-	 Advanced printf (very useful for debugging purposes)
-	 The formats supported by this implementation are:
-		'd' 'u' 'c' 's' 'x' 'X' 'p'.
-
-	 Note: If this option is disabled, the firmware will be only
-	       capable of reported _preformated_ string.
-
-config CARL9170FW_EXPERIMENTAL
-	def_bool y
-	prompt "Experimental Features"
-
-config CARL9170FW_WOL_OPTION
-	def_bool n
-	prompt "Wakeup on WLAN"
-	depends on CARL9170FW_EXPERIMENTAL
-	---help---
-	 With this option enabled, the firmware can wake-up
-	 suspended hosts... As long as they fully support
-	 USB remote wakeup.
-
-config CARL9170FW_WOL
-	def_bool n
-	depends on CARL9170FW_WOL_OPTION
-
-config CARL9170FW_WOL_NL80211_TRIGGERS
-	def_bool n
-	prompt "Standard NL80211 wakeup triggers"
-	depends on CARL9170FW_WOL_OPTION
-	select CARL9170FW_WOL
-	---help---
-	 Available triggers:
-	  * Magic Packet(tm) pattern
-	  * disconnect event
-
-config CARL9170FW_WOL_PROBE_REQUEST
-	def_bool n
-	prompt "Probe Request"
-	depends on CARL9170FW_WOL_OPTION
-	select CARL9170FW_WOL
-	---help---
-	 Scan probe requests for a given SSID.
-
-config CARL9170FW_WOL_PROBE_REQUEST_SSID
-	string
-	prompt "Wakeup on WLAN SSID"
-	default "CARL9170_WAKEUP"
-	depends on CARL9170FW_WOL_PROBE_REQUEST
-
-config CARL9170FW_VIFS_NUM
-	default 1
-	int
-	prompt "Number of additional pseudo virtual interfaces"
-	depends on CARL9170FW_EXPERIMENTAL
-
-config CARL9170FW_FW_MAC_RESET
-	def_bool y
-	prompt "Firmware MAC Chip recovery"
-	depends on CARL9170FW_EXPERIMENTAL
-
-config CARL9170FW_NOISY_MAC_RESET
-	def_bool n
-	prompt "Notify MAC RESET events"
-	depends on CARL9170FW_FW_MAC_RESET
-
-config CARL9170FW_BROKEN_FEATURES
-	def_bool n
-	prompt "Broken Featurs"
-
-config CARL9170FW_DEBUG
-	def_bool n
-	depends on CARL9170FW_BROKEN_FEATURES && CARL9170FW_PRINTF
-	prompt "Enable verbose debugging messages"
-
-config CARL9170FW_DEBUG_LED_HEARTBEAT
-	def_bool n
-	prompt "LED Heartbeat"
-	depends on CARL9170FW_BROKEN_FEATURES
-	---help---
-	 This option conflicts with the application's LED code.
-	 Also, it assumes that you have two LEDs, which is not
-	 necessarily true.
-
-config CARL9170FW_DEBUG_UART
-	def_bool n
-	prompt "Pass debug messages through Highspeed UART"
-	depends on CARL9170FW_BROKEN_FEATURES
-	---help---
-	 This option allows the firmware to send BUG/ERR/INFO/DBG and
-	 hexdumps through the UART _as well_. However, first: you must
-	 connect a working logger.
-
-config CARL9170FW_WATCHDOG_BUTTON
-	def_bool n
-	depends on CARL9170FW_BROKEN && CARL9170FW_GPIO_INTERRUPT
-	prompt "Trigger Watchdog by pressing the WPS button"
-
-choice CARL9170FW_UART_CLOCK
-	prompt "UART Clock"
-	depends on CARL9170FW_DEBUG_UART
-	default CARL9170FW_UART_CLOCK_40M
-
-config CARL9170FW_UART_CLOCK_25M
-	bool "25"
-
-config CARL9170FW_UART_CLOCK_40M
-	bool "40"
-
-endchoice
-
-config CARL9170FW_UNUSABLE
-	def_bool y
-	depends on CARL9170FW_BROKEN || CARL9170FW_DEBUG
-
-config CARL9170FW_USB_MODESWITCH
-	def_bool n
-	prompt "USB 1.1 / 2.0 switching support"
-	depends on CARL9170FW_BROKEN_FEATURES
-	---help---
-	 Mostly implemented, but untested and some serious
-	 doubts remain.
-
-config CARL9170FW_DMA_QUEUE_BUMP
-	def_bool n
-	prompt "Bump a stuck TX queue before doing a MAC reset"
-	depends on CARL9170FW_BROKEN_FEATURES
-
-menu "Build Options"
-config CARL9170FW_AGGRESSIVE_CFLAGS
-	def_bool y
-	prompt "Enable aggressive size optimization"
-	---help---
-	 This option adds several more optimization compiler flags,
-	 which can greatly reduce the firmware size... at the expense
-	 of machine-code readability.
-
-	  Say Y. Else the firmware might not fit onto the device!
-
-endmenu
-
-endmenu
-
-endmenu