Adding upstream version 20230625.upstream/20230625

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

8 files changed, 3307 insertions, 0 deletions

diff --git a/usbdux/Makefile_dux b/usbdux/Makefile_dux
new file mode 100644
index 0000000..16c1c73
--- /dev/null
+++ b/usbdux/Makefile_dux
@@ -0,0 +1,18 @@
+# (c) Bernd Porr
+# GNU public license
+# no warranty
+#
+
+all: usbduxfast_firmware.bin usbdux_firmware.bin usbduxsigma_firmware.bin
+
+usbduxfast_firmware.bin: fx2-include.asm usbduxfast_firmware.asm
+	as31 -Fbin usbduxfast_firmware.asm
+
+usbdux_firmware.bin: fx2-include.asm usbdux_firmware.asm
+	as31 -Fbin usbdux_firmware.asm
+
+usbduxsigma_firmware.bin: fx2-include.asm usbduxsigma_firmware.asm
+	as31 -Fbin usbduxsigma_firmware.asm
+
+clean:
+	rm -f *.bin *~ *.lst *.bin
diff --git a/usbdux/fx2-include.asm b/usbdux/fx2-include.asm
new file mode 100644
index 0000000..9877996
--- /dev/null
+++ b/usbdux/fx2-include.asm
@@ -0,0 +1,164 @@
+; rev 0.91
+; (c) Bernd Porr, BerndPorr@f2s.com
+; GPL, GNU public license
+;
+;   This program is free software; you can redistribute it and/or modify
+;   it under the terms of the GNU General Public License as published by
+;   the Free Software Foundation; either version 2 of the License, or
+;   (at your option) any later version.
+;
+;   This program is distributed in the hope that it will be useful,
+;   but WITHOUT ANY WARRANTY; without even the implied warranty of
+;   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+;   GNU General Public License for more details.
+;
+;   You should have received a copy of the GNU General Public License
+;   along with this program; if not, write to the Free Software
+;   Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+;
+; In conjunction with the as31.
+; Include-file for the FX2 by Cypress. The rest of the regs is defined
+; by the as31 itself.
+;
+; from the TRM of the FX2:
+;
+	;;  CPU control
+	.equ	CPUCS,0E600H
+	.equ	REVCTL,0E60BH
+	;; interface config
+	.equ	IFCONFIG,0E601H
+	.equ	FIFORESET,0E604H
+	;; Endpoint configs
+	.equ	EP1OUTCFG,0E610H
+	.equ	EP1INCFG,0E611H
+	.equ	EP2CFG,0E612H
+	.equ	EP4CFG,0E613H
+	.equ	EP6CFG,0E614H
+	.equ	EP8CFG,0E615H
+	;; packets per frame, always one for USB 1.1
+	.equ	EP2ISOINPKTS,0E640H
+	.equ	EP4ISOINPKTS,0E641H
+	.equ	EP6ISOINPKTS,0E642H
+	.equ	EP8ISOINPKTS,0E643H
+	;; endpoint byte counts
+	.equ	EP1OUTBC,0E68DH
+	.equ	EP2BCH,0E690H
+	.equ	EP2BCL,0E691H
+	.equ	EP4BCH,0E694H
+	.equ	EP4BCL,0E695H
+	.equ	EP6BCH,0E698H
+	.equ	EP6BCL,0E699H
+	.equ	EP8BCH,0E69CH
+	.equ	EP8BCL,0E69DH
+	;;
+	.equ	EP4AUTOINLENH,0E622H
+	.equ	EP4AUTOINLENL,0E623H
+	.equ	EP6AUTOINLENH,0E624H
+	.equ	EP6AUTOINLENL,0E625H
+	.equ	EP2FIFOCFG,0E618H
+	.equ	EP4FIFOCFG,0E619H
+	.equ	EP6FIFOCFG,0E61AH
+	.equ	EP8FIFOCFG,0E61BH
+	;; 
+	.equ	INPKTEND,0E648H
+	.equ	OUTPKTEND,0E649H
+	.equ	GPIFCTLCFG,0E6C3H
+	.equ	GPIFABORT,0E6F5H
+	.equ	GPIFIDLECTL,0E6C2H
+	.equ	GPIFWFSELECT,0E6C0H
+	.equ	GPIFREADYCFG,0E6F3H
+	.equ	GPIFIDLECS,0E6C1H
+	.equ	EP6GPIFFLGSEL,0E6E2H
+	.equ	EP6GPIFPDFSTOP,0E6E3H
+	.equ	EP6GPIFTRIG,0E6E4H
+	.equ	GPIFTCB3,0E6CEH
+	.equ	GPIFTCB2,0E6CFH
+	.equ	GPIFTCB1,0E6D0H
+	.equ	GPIFTCB0,0E6D1H
+	.equ	EP4GPIFFLGSEL,0E6DAH
+	.equ	EP4GPIFPFSTOP,0E6DBH
+	;; 
+	;; endpoint control
+	.equ	EP2CS,0E6A3H
+	.equ	EP4CS,0E6A4H
+	.equ	EP6CS,0E6A5H
+	.equ	EP8CS,0E6A6H
+	;; endpoint buffers
+	.equ	EP2FIFOBUF,0F000H
+	.equ	EP4FIFOBUF,0F400H
+	.equ	EP6FIFOBUF,0F800H
+	.equ	EP8FIFOBUF,0FC00H
+	;; IRQ enable for bulk NAK
+	.equ	IBNIE,0E658H
+	;; interrupt requ for NAK
+	.equ	IBNIRQ,0E659H
+	;; USB INT enables
+	.equ	USBIE,0E65CH
+	;; USB interrupt request
+	.equ	USBIRQ,0E65DH
+	;; endpoint IRQ enable
+	.equ	EPIE,0E65EH
+	;; endpoint IRQ requests
+	.equ	EPIRQ,0E65FH
+	;; USB error IRQ requests
+	.equ	USBERRIE,0E662H
+	;; USB error IRQ request
+	.equ	USBERRIRQ,0E663H
+	;; USB interrupt 2 autovector
+	.equ	INT2IVEC,0E666H
+	;; autovector enable
+	.equ	INTSETUP,0E668H
+	;; port cfg
+	.equ	PORTACFG,0E670H
+	.equ	PORTCCFG,0E671H
+	.equ	PORTECFG,0E672H
+	;; I2C bus
+	.equ	I2CS,0E678H
+	.equ	I2DAT,0E679H
+	.equ	I2CTL,0E67AH
+	;; auto pointers, read/write is directed to the pointed address
+	.equ	XAUTODAT1,0E67BH
+	.equ	XAUTODAT2,0E67CH
+	;; USB-control
+	.equ	USBCS,0E680H
+
+	.equ	IOA,80H
+	.equ	DPL0,82H
+	.equ	DPH0,83H
+	.equ	DPL1,84H
+	.equ	DPH1,85H
+	.equ	DPS,86H
+	.equ	CKCON,8Eh
+	.equ	IOB,90H
+	.equ	EXIF,91h
+	.equ	MPAGE,92h
+	.equ	AUTOPTRH1,9AH
+	.equ	AUTOPTRL1,9BH
+	.equ	AUTOPTRH2,9DH
+	.equ	AUTOPTRL2,9EH
+	.equ	IOC,0A0H
+	.equ	INT2CLR,0A1H
+	.equ	INT4CLR,0A2H
+	.equ	EP2468STAT,0AAH
+	.equ	EP24FIFOFLGS,0ABH
+	.equ	EP68FIFOFLGS,0ACH
+	.equ	AUTOPTRSETUP,0AFH
+	.equ	IOD,0B0H
+	.equ	IOE,0B1H
+	.equ	OEA,0B2H
+	.equ	OEB,0B3H
+	.equ	OEC,0B4H
+	.equ	OED,0B5H
+	.equ	OEE,0B6H
+	.equ	GPIFTRIG,0BBH
+	.equ	EIE,0E8h
+	.equ	EIP,0F8h
+	.equ	GPIFIE,0E660H
+
+;;; serial control
+	.equ	SCON0,098h
+	.equ	SBUF0,099h
+
+	;;; end of file
+	
+
diff --git a/usbdux/usbdux_firmware.asm b/usbdux/usbdux_firmware.asm
new file mode 100644
index 0000000..b93a895
--- /dev/null
+++ b/usbdux/usbdux_firmware.asm
@@ -0,0 +1,1184 @@
+;   usbdux_firmware.asm
+;   Copyright (C) 2004,2009 Bernd Porr, Bernd.Porr@f2s.com
+;   For usbdux.c
+;
+;   This program is free software; you can redistribute it and/or modify
+;   it under the terms of the GNU General Public License as published by
+;   the Free Software Foundation; either version 2 of the License, or
+;   (at your option) any later version.
+;
+;   This program is distributed in the hope that it will be useful,
+;   but WITHOUT ANY WARRANTY; without even the implied warranty of
+;   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+;   GNU General Public License for more details.
+;
+;   You should have received a copy of the GNU General Public License
+;   along with this program; if not, write to the Free Software
+;   Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+;
+;
+; Firmware: usbdux_firmware.asm for usbdux.c
+; Description: University of Stirling USB DAQ & INCITE Technology Limited
+; Devices: [ITL] USB-DUX (usbdux.o)
+; Author: Bernd Porr <Bernd.Porr@f2s.com>
+; Updated: 17 Apr 2009
+; Status: stable
+;
+;;;
+;;;
+;;;
+
+	.inc	fx2-include.asm
+
+	.equ	CHANNELLIST,80h	; channellist in indirect memory
+	
+	.equ	CMD_FLAG,90h	; flag if next IN transf is DIO
+	.equ	SGLCHANNEL,91h	; channel for INSN
+	.equ	PWMFLAG,92h	; PWM
+	
+	.equ	DIOSTAT0,98h	; last status of the digital port
+	.equ	DIOSTAT1,99h	; same for the second counter
+	
+	.equ	CTR0,0A0H	; counter 0
+	.equ	CTR1,0A2H	; counter 1
+			
+	.org	0000h		; after reset the processor starts here
+	ljmp	main		; jump to the main loop
+
+	.org	000bh		; timer 0 irq
+	ljmp	timer0_isr
+
+	.org	0043h		; the IRQ2-vector
+	ljmp	jmptbl		; irq service-routine
+	
+	.org	0100h		; start of the jump table
+
+jmptbl:	ljmp	sudav_isr
+	nop
+	ljmp	sof_isr
+	nop
+	ljmp	sutok_isr
+	nop
+	ljmp	suspend_isr
+	nop
+	ljmp	usbreset_isr
+	nop
+	ljmp	hispeed_isr
+	nop
+	ljmp	ep0ack_isr
+	nop
+	ljmp	spare_isr
+	nop
+	ljmp	ep0in_isr
+	nop
+	ljmp	ep0out_isr
+	nop
+	ljmp	ep1in_isr
+	nop
+	ljmp	ep1out_isr
+	nop
+	ljmp	ep2_isr
+	nop
+	ljmp	ep4_isr
+	nop
+	ljmp	ep6_isr
+	nop
+	ljmp	ep8_isr
+	nop
+	ljmp	ibn_isr
+	nop
+	ljmp	spare_isr
+	nop
+	ljmp	ep0ping_isr
+	nop
+	ljmp	ep1ping_isr
+	nop
+	ljmp	ep2ping_isr
+	nop
+	ljmp	ep4ping_isr
+	nop
+	ljmp	ep6ping_isr
+	nop
+	ljmp	ep8ping_isr
+	nop
+	ljmp	errlimit_isr
+	nop
+	ljmp	spare_isr
+	nop
+	ljmp	spare_isr
+	nop
+	ljmp	spare_isr
+	nop
+	ljmp	ep2isoerr_isr
+	nop
+	ljmp	ep4isoerr_isr
+	nop
+	ljmp	ep6isoerr_isr
+	nop
+	ljmp	ep8isoerr_isr
+
+	
+	;; dummy isr
+sudav_isr:	
+sutok_isr:	
+suspend_isr:	
+usbreset_isr:	
+hispeed_isr:	
+ep0ack_isr:	
+spare_isr:	
+ep0in_isr:	
+ep0out_isr:	
+ep1in_isr:	
+ibn_isr:	
+ep0ping_isr:	
+ep1ping_isr:	
+ep2ping_isr:	
+ep4ping_isr:	
+ep6ping_isr:	
+ep8ping_isr:	
+errlimit_isr:	
+ep2isoerr_isr:	
+ep4isoerr_isr:	
+ep6isoerr_isr:	
+ep8isoerr_isr:
+ep6_isr:
+ep2_isr:
+ep4_isr:	
+
+	push	dps
+	push	dpl
+	push	dph
+	push	dpl1
+	push	dph1
+	push	acc
+	push	psw
+
+	;; clear the USB2 irq bit and return
+	mov	a,EXIF
+	clr	acc.4
+	mov	EXIF,a
+
+	pop	psw
+	pop	acc 
+	pop	dph1 
+	pop	dpl1
+	pop	dph 
+	pop	dpl 
+	pop	dps
+	
+	reti
+
+		
+;;; main program
+;;; basically only initialises the processor and
+;;; then engages in an endless loop
+main:
+	mov	DPTR,#CPUCS	; CPU control register
+	mov	a,#00010000b	; 48Mhz
+	lcall	syncdelaywr
+
+        mov     dptr,#REVCTL
+        mov     a,#00000011b    ; allows skip
+        lcall   syncdelaywr
+
+	mov	IP,#0		; all std 8051 int have low priority
+	mov	EIP,#0FFH	; all FX2 interrupts have high priority
+	
+	mov	dptr,#INTSETUP	; IRQ setup register
+	mov	a,#08h		; enable autovector
+	lcall	syncdelaywr
+
+	lcall	initAD		; init the ports to the converters
+
+	lcall	initeps		; init the isochronous data-transfer
+
+	lcall	init_timer
+	
+mloop2:	nop
+
+;;; pwm
+	mov	r0,#PWMFLAG	; pwm on?
+	mov	a,@r0		; get info
+	jz	mloop2		; it's off
+
+	mov	a,GPIFTRIG	; GPIF status
+	anl	a,#80h		; done bit
+	jz	mloop2		; GPIF still busy
+
+        mov     a,#01h		; WR,EP4, 01 = EP4
+        mov     GPIFTRIG,a	; restart it
+
+	sjmp	mloop2		; loop for ever
+
+
+;;; GPIF waveform for PWM
+waveform:
+	;;      0     1     2     3     4     5     6     7(not used)
+	;; len (gives 50.007Hz)
+	.db	195,  195,  195,  195,  195,  195,  1,    1
+
+	;; opcode
+	.db	002H, 006H, 002H, 002H, 002H, 002H, 002H, 002H
+	
+	;; out
+	.db	0ffH, 0ffH, 0ffH, 0ffH, 0ffH, 0ffH, 0ffH, 0ffH
+
+	;; log
+	.db	000H, 000H, 000H, 000H, 000H, 000H, 000H, 000H
+
+
+stopPWM:
+	mov	r0,#PWMFLAG	; flag for PWM
+	mov	a,#0		; PWM (for the main loop)
+	mov	@r0,a		; set it
+
+	mov	dptr,#IFCONFIG	; switch off GPIF
+	mov	a,#10000000b	; gpif, 30MHz, internal IFCLK
+	lcall	syncdelaywr
+	ret
+	
+
+;;; init PWM
+startPWM:
+	mov	dptr,#IFCONFIG	; switch on IFCLK signal
+	mov	a,#10000010b	; gpif, 30MHz, internal IFCLK
+	lcall	syncdelaywr
+
+	mov	OEB,0FFH	; output to port B
+
+	mov	DPTR,#EP4CFG
+	mov	a,#10100000b	; valid, out, bulk
+	movx	@DPTR,a
+
+	;; reset the endpoint
+	mov	dptr,#FIFORESET
+	mov	a,#80h		; NAK
+	lcall	syncdelaywr
+	mov	a,#84h		; reset EP4 + NAK
+	lcall	syncdelaywr
+	mov	a,#0		; normal op
+	lcall	syncdelaywr
+
+	mov	dptr,#EP4BCL
+	mov	a,#0H		; discard packets
+	lcall	syncdelaywr	; empty FIFO buffer
+	lcall	syncdelaywr	; empty FIFO buffer
+
+	;; aborts all transfers by the GPIF
+	mov	dptr,#GPIFABORT
+	mov	a,#0ffh		; abort all transfers
+	lcall	syncdelaywr
+
+	;; wait for GPIF to finish
+wait_f_abort:
+	mov	a,GPIFTRIG	; GPIF status
+	anl	a,#80h		; done bit
+	jz	wait_f_abort	; GPIF busy
+
+        mov     dptr,#GPIFCTLCFG
+        mov     a,#10000000b    ; tri state for CTRL
+        lcall   syncdelaywr
+
+        mov     dptr,#GPIFIDLECTL
+        mov     a,#11110000b    ; all CTL outputs low
+        lcall   syncdelaywr
+
+	;; abort if FIFO is empty
+        mov     a,#00000001b    ; abort if empty
+        mov     dptr,#EP4GPIFFLGSEL
+        lcall   syncdelaywr
+
+	;; 
+        mov     a,#00000001b    ; stop if GPIF flg
+        mov     dptr,#EP4GPIFPFSTOP
+        lcall   syncdelaywr
+
+	;; transaction counter
+	mov	a,#0ffH
+	mov	dptr,#GPIFTCB3
+	lcall	syncdelaywr
+
+	;; transaction counter
+	mov	a,#0ffH
+	mov	dptr,#GPIFTCB2
+	lcall	syncdelaywr
+
+	;; transaction counter
+	mov	a,#0ffH		; 512 bytes
+	mov	dptr,#GPIFTCB1
+	lcall	syncdelaywr
+
+	;; transaction counter
+	mov	a,#0ffH
+	mov	dptr,#GPIFTCB0
+	lcall	syncdelaywr
+
+	;; RDY pins. Not used here.
+        mov     a,#0
+        mov     dptr,#GPIFREADYCFG
+        lcall   syncdelaywr
+
+	;; drives the output in the IDLE state
+        mov     a,#1
+        mov     dptr,#GPIFIDLECS
+        lcall   syncdelaywr
+
+	;; direct data transfer from the EP to the GPIF
+	mov	dptr,#EP4FIFOCFG
+	mov	a,#00010000b	; autoout=1, byte-wide
+	lcall	syncdelaywr
+
+	;; waveform 0 is used for FIFO out
+	mov	dptr,#GPIFWFSELECT
+	mov	a,#00000000b
+	movx	@dptr,a
+	lcall	syncdelay
+
+	;; transfer the delay byte from the EP to the waveform
+	mov	dptr,#0e781h	; EP1 buffer
+	movx	a,@dptr		; get the delay
+	mov	dptr,#waveform	; points to the waveform
+	mov	r2,#6		; fill 6 bytes
+timloop:
+	movx	@dptr,a		; save timing in a xxx
+	inc	dptr
+	djnz	r2,timloop	; fill the 6 delay bytes
+
+	;; load waveform
+        mov     AUTOPTRH2,#0E4H ; XDATA0H
+        lcall   syncdelay
+        mov     AUTOPTRL2,#00H  ; XDATA0L
+        lcall   syncdelay
+
+	mov	dptr,#waveform	; points to the waveform
+	
+        mov     AUTOPTRSETUP,#7 ; autoinc and enable
+        lcall   syncdelay
+
+        mov     r2,#20H         ; 32 bytes to transfer
+
+wavetr:
+        movx    a,@dptr
+	inc	dptr
+	push	dpl
+	push	dph
+	push	dpl1
+	push	dph1
+        mov     dptr,#XAUTODAT2
+        movx    @dptr,a
+        lcall   syncdelay
+	pop	dph1 
+	pop	dpl1
+	pop	dph 
+	pop	dpl
+        djnz    r2,wavetr
+
+	mov	dptr,#OUTPKTEND
+	mov	a,#084H
+	lcall	syncdelaywr
+	lcall	syncdelaywr
+
+	mov	r0,#PWMFLAG	; flag for PWM
+	mov	a,#1		; PWM (for the main loop)
+	mov	@r0,a		; set it
+
+	ret
+
+
+
+;;; initialise the ports for the AD-converter
+initAD:
+	mov	OEA,#27H	;PortA0,A1,A2,A5 Outputs
+	mov	IOA,#22H	;/CS = 1, disable transfers to the converters
+	ret
+
+
+;;; init the timer for the soft counters
+init_timer:
+	;; init the timer for 2ms sampling rate
+	mov	CKCON,#00000001b; CLKOUT/12 for timer
+	mov	TL0,#010H	; 16
+	mov	TH0,#0H		; 256
+	mov	IE,#82H		; switch on timer interrupt (80H for all IRQs)
+	mov	TMOD,#00000000b	; 13 bit counters
+	setb	TCON.4		; enable timer 0
+	ret
+
+
+;;; from here it's only IRQ handling...
+	
+;;; A/D-conversion:
+;;; control-byte in a,
+;;; result in r3(low) and r4(high)
+;;; this routine is optimised for speed
+readAD:				; mask the control byte
+	anl	a,#01111100b	; only the channel, gain+pol are left
+	orl	a,#10000001b	; start bit, external clock
+	;; set CS to low
+	clr	IOA.1		; set /CS to zero
+	;; send the control byte to the AD-converter
+	mov 	R2,#8		; bit-counter
+bitlp:	jnb     ACC.7,bitzero	; jump if Bit7 = 0?
+	setb	IOA.2		; set the DIN bit
+	sjmp	clock		; continue with the clock
+bitzero:clr	IOA.2		; clear the DIN bit
+clock:	setb	IOA.0		; SCLK = 1
+	clr	IOA.0		; SCLK = 0
+        rl      a               ; next Bit
+        djnz    R2,bitlp
+
+	;; continue the aquisition (already started)
+	clr	IOA.2		; clear the DIN bit
+	mov 	R2,#5		; five steps for the aquision
+clockaq:setb	IOA.0		; SCLK = 1
+	clr	IOA.0		; SCLK = 0
+        djnz    R2,clockaq	; loop
+	
+	;; read highbyte from the A/D-converter
+	;; and do the conversion
+	mov	r4,#0 		; Highbyte goes into R4
+	mov	R2,#4		; COUNTER 4 data bits in the MSB
+	mov	r5,#08h		; create bit-mask
+gethi:				; loop get the 8 highest bits from MSB downw
+	setb	IOA.0		; SCLK = 1
+	clr	IOA.0		; SCLK = 0
+	mov	a,IOA		; from port A
+	jnb	ACC.4,zerob	; the in-bit is zero
+	mov	a,r4		; get the byte
+	orl	a,r5		; or the bit to the result
+	mov	r4,a		; save it again in r4
+zerob:	mov	a,r5		; get r5 in order to shift the mask
+	rr	a		; rotate right
+	mov	r5,a		; back to r5
+	djnz	R2,gethi
+	;; read the lowbyte from the A/D-converter
+	mov	r3,#0 		; Lowbyte goes into R3
+	mov	r2,#8		; COUNTER 8 data-bits in the LSB
+	mov	r5,#80h		; create bit-mask
+getlo:				; loop get the 8 highest bits from MSB downw
+	setb	IOA.0		; SCLK = 1
+	clr	IOA.0		; SCLK = 0
+	mov	a,IOA		; from port A
+	jnb	ACC.4,zerob2	; the in-bit is zero
+	mov	a,r3		; get the result-byte
+	orl	a,r5		; or the bit to the result
+	mov	r3,a		; save it again in r4
+zerob2:	mov	a,r5		; get r5 in order to shift the mask
+	rr	a		; rotate right
+	mov	r5,a		; back to r5
+	djnz	R2,getlo
+	setb	IOA.1		; set /CS to one
+	;;
+	ret
+	
+
+	
+;;; aquires data from A/D channels and stores them in the EP6 buffer
+conv_ad:
+	mov	AUTOPTRH1,#0F8H	; auto pointer on EP6
+	mov	AUTOPTRL1,#00H
+	mov	AUTOPTRSETUP,#7
+	mov	r0,#CHANNELLIST	; points to the channellist
+
+	mov	a,@r0		; number of channels
+	mov	r1,a		; counter
+
+	mov 	DPTR,#XAUTODAT1	; auto pointer
+convloop:
+	inc	r0
+	mov 	a,@r0		; Channel
+	lcall 	readAD
+	mov 	a,R3		;
+	movx 	@DPTR,A
+	mov 	a,R4		;
+	movx 	@DPTR,A
+	djnz	r1,convloop
+
+	ret
+
+
+
+
+;;; initilise the transfer
+;;; It is assumed that the USB interface is in alternate setting 3
+initeps:
+	mov	dptr,#FIFORESET
+	mov	a,#80H		
+	movx	@dptr,a		; reset all fifos
+	mov	a,#2	
+	movx	@dptr,a		; 
+	mov	a,#4		
+	movx	@dptr,a		; 
+	mov	a,#6		
+	movx	@dptr,a		; 
+	mov	a,#8		
+	movx	@dptr,a		; 
+	mov	a,#0		
+	movx	@dptr,a		; normal operat
+	
+	mov	DPTR,#EP2CFG
+	mov	a,#10010010b	; valid, out, double buff, iso
+	movx	@DPTR,a
+
+	mov	dptr,#EP2FIFOCFG
+	mov	a,#00000000b	; manual
+	movx	@dptr,a
+
+	mov	dptr,#EP2BCL	; "arm" it
+	mov	a,#00h
+	movx	@DPTR,a		; can receive data
+	lcall	syncdelay	; wait to sync
+	movx	@DPTR,a		; can receive data
+	lcall	syncdelay	; wait to sync
+	movx	@DPTR,a		; can receive data
+	lcall	syncdelay	; wait to sync
+	
+	mov	DPTR,#EP1OUTCFG
+	mov	a,#10100000b	; valid
+	movx	@dptr,a
+
+	mov	dptr,#EP1OUTBC	; "arm" it
+	mov	a,#00h
+	movx	@DPTR,a		; can receive data
+	lcall	syncdelay	; wait until we can write again
+	movx	@dptr,a		; make shure its really empty
+	lcall	syncdelay	; wait
+
+	mov	DPTR,#EP6CFG	; ISO data from here to the host
+	mov	a,#11010010b	; Valid
+	movx	@DPTR,a		; ISO transfer, double buffering
+
+	mov	DPTR,#EP8CFG	; EP8
+	mov	a,#11100000b	; BULK data from here to the host
+	movx	@DPTR,a		;
+
+	mov	dptr,#EPIE	; interrupt enable
+	mov	a,#10001000b	; enable irq for ep1out,8
+	movx	@dptr,a		; do it
+
+	mov	dptr,#EPIRQ	; clear IRQs
+	mov	a,#10100000b
+	movx	@dptr,a
+
+	;; enable interrups
+        mov     DPTR,#USBIE	; USB int enables register
+        mov     a,#2            ; enables SOF (1ms/125us interrupt)
+        movx    @DPTR,a         ; 
+
+	mov	EIE,#00000001b	; enable INT2 in the 8051's SFR
+	mov	IE,#80h		; IE, enable all interrupts
+
+	ret
+
+
+;;; counter
+;;; r0: DIOSTAT
+;;; r1:	counter address
+;;; r2:	up/down-mask
+;;; r3:	reset-mask
+;;; r4:	clock-mask
+counter:	
+	mov	a,IOB		; actual IOB input state
+	mov	r5,a		; save in r5
+	anl	a,r3		; bit mask for reset
+	jz	no_reset	; reset if one
+	clr	a		; set counter to zero
+	mov	@r1,a
+	inc	r4
+	mov	@r1,a
+	sjmp	ctr_end
+no_reset:	
+	mov	a,@r0		; get last state
+	xrl	a,r5		; has it changed?
+	anl	a,r5		; is it now on?
+	anl	a,r4		; mask out the port
+	jz	ctr_end		; no rising edge
+	mov	a,r5		; get port B again
+	anl	a,r2		; test if up or down
+	jnz	ctr_up		; count up
+	mov	a,@r1
+	dec	a
+	mov	@r1,a
+	cjne	a,#0ffh,ctr_end	; underflow?
+	inc	r1		; high byte
+	mov	a,@r1
+	dec	a
+	mov	@r1,a
+	sjmp	ctr_end
+ctr_up:				; count up
+	mov	a,@r1
+	inc	a
+	mov	@r1,a
+	jnz	ctr_end
+	inc	r1		; high byte
+	mov	a,@r1
+	inc	a
+	mov	@r1,a
+ctr_end:
+	mov	a,r5
+	mov	@r0,a
+	ret
+
+;;; implements two soft counters with up/down and reset
+timer0_isr:
+	push	dps
+	push	acc
+	push	psw
+	push	00h		; R0
+	push	01h		; R1
+	push	02h		; R2
+	push	03h		; R3
+	push	04h		; R4
+	push	05h		; R5
+		
+	mov	r0,#DIOSTAT0	; status of port
+	mov	r1,#CTR0	; address of counter0
+	mov	a,#00000001b	; bit 0
+	mov	r4,a		; clock
+	rl	a		; bit 1
+	mov	r2,a		; up/down
+	rl	a		; bit 2
+	mov	r3,a		; reset mask
+	lcall	counter
+	inc	r0		; to DISTAT1
+	inc	r1		; to CTR1
+	inc	r1
+	mov	a,r3
+	rl	a		; bit 3
+	rl	a		; bit 4
+	mov	r4,a		; clock
+	rl	a		; bit 5
+	mov	r2,a		; up/down
+	rl	a		; bit 6
+	mov	r3,a		; reset
+	lcall	counter
+	
+	pop	05h		; R5
+	pop	04h		; R4
+	pop	03h		; R3
+	pop	02h		; R2
+	pop	01h		; R1
+	pop	00h		; R0
+	pop	psw
+	pop	acc 
+	pop	dps
+
+	reti
+
+;;; interrupt-routine for SOF
+;;; is for full speed
+sof_isr:
+	push	dps
+	push	dpl
+	push	dph
+	push	dpl1
+	push	dph1
+	push	acc
+	push	psw
+	push	00h		; R0
+	push	01h		; R1
+	push	02h		; R2
+	push	03h		; R3
+	push	04h		; R4
+	push	05h		; R5
+	push	06h		; R6
+	push	07h		; R7
+		
+	mov	a,EP2468STAT
+	anl	a,#20H		; full?
+	jnz	epfull		; EP6-buffer is full
+
+	lcall	conv_ad		; conversion
+
+	mov	DPTR,#EP6BCH	; byte count H
+	mov	a,#0		; is zero
+	lcall	syncdelaywr	; wait until we can write again
+	
+	mov	DPTR,#EP6BCL	; byte count L
+	mov	a,#10H		; is 8x word = 16 bytes
+	lcall	syncdelaywr	; wait until we can write again
+	
+epfull:
+	;; do the D/A conversion
+	mov	a,EP2468STAT
+	anl	a,#01H		; empty
+	jnz	epempty		; nothing to get
+
+	mov	dptr,#0F000H	; EP2 fifo buffer
+	lcall	dalo		; conversion
+
+	mov	dptr,#EP2BCL	; "arm" it
+	mov	a,#00h
+	lcall	syncdelaywr	; wait for the rec to sync
+	lcall	syncdelaywr	; wait for the rec to sync
+
+epempty:	
+	;; clear INT2
+	mov	a,EXIF		; FIRST clear the USB (INT2) interrupt request
+	clr	acc.4
+	mov	EXIF,a		; Note: EXIF reg is not 8051 bit-addressable
+	
+	mov	DPTR,#USBIRQ	; points to the SOF
+	mov	a,#2		; clear the SOF
+	movx	@DPTR,a
+
+nosof:	
+	pop	07h
+	pop	06h
+	pop	05h
+	pop	04h		; R4
+	pop	03h		; R3
+	pop	02h		; R2
+	pop	01h		; R1
+	pop	00h		; R0
+	pop	psw
+	pop	acc 
+	pop	dph1 
+	pop	dpl1
+	pop	dph 
+	pop	dpl 
+	pop	dps
+	reti
+
+
+reset_ep8:
+	;; erase all data in ep8
+	mov	dptr,#FIFORESET
+	mov	a,#80H		; NAK
+	lcall	syncdelaywr
+	mov	dptr,#FIFORESET
+	mov	a,#8		; reset EP8
+	lcall	syncdelaywr
+	mov	dptr,#FIFORESET
+	mov	a,#0		; normal operation
+	lcall	syncdelaywr
+	ret
+
+
+reset_ep6:
+	;; throw out old data
+	mov	dptr,#FIFORESET
+	mov	a,#80H		; NAK
+	lcall	syncdelaywr
+	mov	dptr,#FIFORESET
+	mov	a,#6		; reset EP6
+	lcall	syncdelaywr
+	mov	dptr,#FIFORESET
+	mov	a,#0		; normal operation
+	lcall	syncdelaywr
+	ret
+
+;;; interrupt-routine for ep1out
+;;; receives the channel list and other commands
+ep1out_isr:
+	push	dps
+	push	dpl
+	push	dph
+	push	dpl1
+	push	dph1
+	push	acc
+	push	psw
+	push	00h		; R0
+	push	01h		; R1
+	push	02h		; R2
+	push	03h		; R3
+	push	04h		; R4
+	push	05h		; R5
+	push	06h		; R6
+	push	07h		; R7
+		
+	mov	dptr,#0E780h	; FIFO buffer of EP1OUT
+	movx	a,@dptr		; get the first byte
+	mov	r0,#CMD_FLAG	; pointer to the command byte
+	mov 	@r0,a		; store the command byte for ep8
+
+	mov	dptr,#ep1out_jmp; jump table for the different functions
+	rl	a		; multiply by 2: sizeof sjmp
+	jmp	@a+dptr		; jump to the jump table
+	;; jump table, corresponds to the command bytes defined
+	;; in usbdux.c
+ep1out_jmp:
+	sjmp	storechannellist; a=0
+	sjmp	single_da	; a=1
+	sjmp	config_digital_b; a=2
+	sjmp	write_digital_b	; a=3
+	sjmp	storesglchannel	; a=4
+	sjmp	readcounter	; a=5
+	sjmp	writecounter	; a=6
+	sjmp	pwm_on		; a=7
+	sjmp	pwm_off		; a=8
+
+pwm_on:
+	lcall	startPWM
+	sjmp	over_da
+
+pwm_off:
+	lcall	stopPWM
+	sjmp	over_da
+
+	;; read the counter
+readcounter:
+	lcall	reset_ep8	; reset ep8
+	lcall	ep8_ops		; fill the counter data in there
+	sjmp	over_da		; jump to the end
+
+	;; write zeroes to the counters
+writecounter:
+	mov	dptr,#0e781h	; buffer
+	mov	r0,#CTR0	; r0 points to counter 0
+	movx	a,@dptr		; channel number
+	jz	wrctr0		; first channel
+	mov	r1,a		; counter
+wrctrl:
+	inc	r0		; next counter
+	inc	r0		; next counter
+	djnz	r1,wrctrl	; advance to the right counter
+wrctr0:
+	inc	dptr		; get to the value
+	movx	a,@dptr		; get value
+	mov	@r0,a		; save in ctr
+	inc	r0		; next byte
+	inc	dptr
+	movx	a,@dptr		; get value
+	mov	@r0,a		; save in ctr
+	sjmp	over_da		; jump to the end
+
+storesglchannel:
+	mov	r0,#SGLCHANNEL	; the conversion bytes are now stored in 80h
+	mov	dptr,#0e781h	; FIFO buffer of EP1OUT
+	movx	a,@dptr		; 
+	mov	@r0,a
+
+	lcall	reset_ep8	; reset FIFO
+	;; Save new A/D data in EP8. This is the first byte
+	;; the host will read during an INSN. If there are
+	;; more to come they will be handled by the ISR of
+	;; ep8.
+	lcall	ep8_ops		; get A/D data
+		
+	sjmp	over_da
+
+	
+;;; Channellist:
+;;; the first byte is zero:
+;;; we've just received the channel list
+;;; the channel list is stored in the addresses from CHANNELLIST which
+;;; are _only_ reachable by indirect addressing
+storechannellist:
+	mov	r0,#CHANNELLIST	; the conversion bytes are now stored in 80h
+	mov	r2,#9		; counter
+	mov	dptr,#0e781h	; FIFO buffer of EP1OUT
+chanlloop:	
+	movx	a,@dptr		; 
+	mov	@r0,a
+	inc	dptr
+	inc	r0
+	djnz	r2,chanlloop
+
+	lcall	reset_ep6	; reset FIFO
+	
+	;; load new A/D data into EP6
+	;; This must be done. Otherwise the ISR is never called.
+	;; The ISR is only called when data has _left_ the
+	;; ep buffer here it has to be refilled.
+	lcall	ep6_arm		; fill with the first data byte
+	
+	sjmp	over_da
+
+;;; Single DA conversion. The 2 bytes are in the FIFO buffer
+single_da:
+	mov	dptr,#0e781h	; FIFO buffer of EP1OUT
+	lcall	dalo		; conversion
+	sjmp	over_da
+
+;;; configure the port B as input or output (bitwise)
+config_digital_b:
+	mov	dptr,#0e781h	; FIFO buffer of EP1OUT
+	movx	a,@dptr		; get the second byte
+	mov	OEB,a		; set the output enable bits
+	sjmp	over_da
+	
+;;; Write one byte to the external digital port B
+;;; and prepare for digital read
+write_digital_b:
+	mov	dptr,#0e781h	; FIFO buffer of EP1OUT
+	movx	a,@dptr		; get the second byte
+	mov	OEB,a		; output enable
+	inc	dptr		; next byte
+	movx	a,@dptr		; bits
+	mov	IOB,a		; send the byte to the I/O port
+
+	lcall	reset_ep8	; reset FIFO of ep 8
+
+	;; fill ep8 with new data from port B
+	;; When the host requests the data it's already there.
+	;; This must be so. Otherwise the ISR is not called.
+	;; The ISR is only called when a packet has been delivered
+	;; to the host. Thus, we need a packet here in the
+	;; first instance.
+	lcall	ep8_ops		; get digital data
+
+	;; 
+	;; for all commands the same
+over_da:	
+	mov	dptr,#EP1OUTBC
+	mov	a,#00h
+	lcall	syncdelaywr	; arm
+	lcall	syncdelaywr	; arm
+	lcall	syncdelaywr	; arm
+
+	;; clear INT2
+	mov	a,EXIF		; FIRST clear the USB (INT2) interrupt request
+	clr	acc.4
+	mov	EXIF,a		; Note: EXIF reg is not 8051 bit-addressable
+
+	mov	DPTR,#EPIRQ	; 
+	mov	a,#00001000b	; clear the ep1outirq
+	movx	@DPTR,a
+
+	pop	07h
+	pop	06h
+	pop	05h
+	pop	04h		; R4
+	pop	03h		; R3
+	pop	02h		; R2
+	pop	01h		; R1
+	pop	00h		; R0
+	pop	psw
+	pop	acc 
+	pop	dph1 
+	pop	dpl1
+	pop	dph 
+	pop	dpl 
+	pop	dps
+	reti
+
+
+	
+;;; all channels
+dalo:
+	movx	a,@dptr		; number of channels
+	inc	dptr		; pointer to the first channel
+	mov	r0,a		; 4 channels
+nextDA:	
+	movx	a,@dptr		; get the first low byte
+	mov	r3,a		; store in r3 (see below)
+	inc	dptr		; point to the high byte
+	movx	a,@dptr		; get the high byte
+	mov	r4,a		; store in r4 (for writeDA)
+	inc	dptr		; point to the channel number
+	movx	a,@dptr		; get the channel number
+	inc	dptr		; get ready for the next channel
+	lcall	writeDA		; write value to the DAC
+	djnz	r0,nextDA	; next channel
+	ret
+
+
+
+;;; D/A-conversion:
+;;; control-byte in a,
+;;; value in r3(low) and r4(high)
+writeDA:			; mask the control byte
+	anl	a,#11000000b	; only the channel is left
+	orl	a,#00110000b	; internal clock, bipolar mode, +/-5V
+	orl	a,r4		; or the value of R4 to it
+	;; set CS to low
+	clr	IOA.5		; set /CS to zero
+	;; send the first byte to the DA-converter
+	mov 	R2,#8		; bit-counter
+DA1:    jnb     ACC.7,zeroda	; jump if Bit7 = 0?
+	setb	IOA.2		; set the DIN bit
+	sjmp	clkda		; continue with the clock
+zeroda: clr	IOA.2		; clear the DIN bit
+clkda:	setb	IOA.0		; SCLK = 1
+	clr	IOA.0		; SCLK = 0
+        rl      a               ; next Bit
+        djnz    R2,DA1
+
+	
+	;; send the second byte to the DA-converter
+	mov	a,r3		; low byte
+	mov 	R2,#8		; bit-counter
+DA2:    jnb     ACC.7,zeroda2	; jump if Bit7 = 0?
+	setb	IOA.2		; set the DIN bit
+	sjmp	clkda2		; continue with the clock
+zeroda2:clr	IOA.2		; clear the DIN bit
+clkda2:	setb	IOA.0		; SCLK = 1
+	clr	IOA.0		; SCLK = 0
+        rl      a               ; next Bit
+        djnz    R2,DA2
+	;; 
+	setb	IOA.5		; set /CS to one
+	;; 
+noDA:	ret
+	
+
+
+;;; arm ep6
+ep6_arm:
+	lcall	conv_ad
+	
+	mov	DPTR,#EP6BCH	; byte count H
+	mov	a,#0		; is zero
+	lcall	syncdelaywr	; wait until the length has arrived
+	
+	mov	DPTR,#EP6BCL	; byte count L
+	mov	a,#10H		; is one
+	lcall	syncdelaywr	; wait until the length has been proc
+	ret
+	
+
+
+;;; converts one analog/digital channel and stores it in EP8
+;;; also gets the content of the digital ports B and D depending on
+;;; the COMMAND flag
+ep8_ops:
+	mov	dptr,#0fc01h	; ep8 fifo buffer
+	clr	a		; high byte
+	movx	@dptr,a		; set H=0
+	mov	dptr,#0fc00h	; low byte
+	mov	r0,#CMD_FLAG
+	mov	a,@r0
+	movx	@dptr,a		; save command byte
+
+	mov	dptr,#ep8_jmp	; jump table for the different functions
+	rl	a		; multiply by 2: sizeof sjmp
+	jmp	@a+dptr		; jump to the jump table
+	;; jump table, corresponds to the command bytes defined
+	;; in usbdux.c
+ep8_jmp:
+	sjmp	ep8_err		; a=0, err
+	sjmp	ep8_err		; a=1, err
+	sjmp	ep8_err		; a=2, err
+	sjmp	ep8_dio		; a=3, digital read
+	sjmp	ep8_sglchannel	; a=4, analog A/D
+	sjmp	ep8_readctr	; a=5, read counter
+	sjmp	ep8_err		; a=6, write counter
+
+	;; reads all counters
+ep8_readctr:
+	mov	r0,#CTR0	; points to counter0
+	mov	dptr,#0fc02h	; ep8 fifo buffer
+	mov	r1,#8		; transfer 4 16bit counters
+ep8_ctrlp:
+	mov	a,@r0		; get the counter
+	movx	@dptr,a		; save in the fifo buffer
+	inc	r0		; inc pointer to the counters
+	inc	dptr		; inc pointer to the fifo buffer
+	djnz	r1,ep8_ctrlp	; loop until ready
+	
+	sjmp	ep8_send	; send the data
+	
+	;; read one A/D channel
+ep8_sglchannel:		
+	mov	r0,#SGLCHANNEL	; points to the channel
+	mov 	a,@r0		; Ch0
+	
+	lcall 	readAD		; start the conversion
+		
+	mov 	DPTR,#0fc02h	; EP8 FIFO 
+	mov 	a,R3		; get low byte
+	movx 	@DPTR,A		; store in FIFO
+	inc	dptr		; next fifo entry
+	mov 	a,R4		; get high byte
+	movx 	@DPTR,A		; store in FIFO
+
+	sjmp	ep8_send	; send the data
+
+	;; read the digital lines
+ep8_dio:	
+	mov 	DPTR,#0fc02h	; store the contents of port B
+	mov	a,IOB		; in the next
+	movx	@dptr,a		; entry of the buffer
+
+	inc	dptr
+	clr	a		; high byte is zero
+	movx	@dptr,a		; next byte of the EP
+	
+ep8_send:	
+	mov	DPTR,#EP8BCH	; byte count H
+	mov	a,#0		; is zero
+	lcall	syncdelaywr
+	
+	mov	DPTR,#EP8BCL	; byte count L
+	mov	a,#10H		; 16 bytes
+	lcall	syncdelaywr	; send the data over to the host
+
+ep8_err:	
+	ret
+
+
+
+;;; EP8 interrupt: gets one measurement from the AD converter and
+;;; sends it via EP8. The channel # is stored in address 80H.
+;;; It also gets the state of the digital registers B and D.
+ep8_isr:	
+	push	dps
+	push	dpl
+	push	dph
+	push	dpl1
+	push	dph1
+	push	acc
+	push	psw
+	push	00h		; R0
+	push	01h		; R1
+	push	02h		; R2
+	push	03h		; R3
+	push	04h		; R4
+	push	05h		; R5
+	push	06h		; R6
+	push	07h		; R7
+		
+	lcall	ep8_ops
+	
+	;; clear INT2
+	mov	a,EXIF		; FIRST clear the USB (INT2) interrupt request
+	clr	acc.4
+	mov	EXIF,a		; Note: EXIF reg is not 8051 bit-addressable
+
+	mov	DPTR,#EPIRQ	; 
+	mov	a,#10000000b	; clear the ep8irq
+	movx	@DPTR,a
+
+	pop	07h
+	pop	06h
+	pop	05h
+	pop	04h		; R4
+	pop	03h		; R3
+	pop	02h		; R2
+	pop	01h		; R1
+	pop	00h		; R0
+	pop	psw
+	pop	acc 
+	pop	dph1 
+	pop	dpl1
+	pop	dph 
+	pop	dpl 
+	pop	dps
+	reti
+
+
+;; need to delay every time the byte counters
+;; for the EPs have been changed.
+
+syncdelay:
+	nop
+	nop
+	nop
+	nop
+	nop
+	nop
+	nop
+	nop
+	nop
+	ret
+
+syncdelaywr:
+	movx	@dptr,a
+	lcall	syncdelay
+	ret
+
+
+.End
+
+
diff --git a/usbdux/usbduxfast_firmware.asm b/usbdux/usbduxfast_firmware.asm
new file mode 100644
index 0000000..0d8e7f8
--- /dev/null
+++ b/usbdux/usbduxfast_firmware.asm
@@ -0,0 +1,547 @@
+;   usbduxfast_firmware.asm
+;   Copyright (C) 2004,2009 Bernd Porr, Bernd.Porr@f2s.com
+;
+;   This program is free software; you can redistribute it and/or modify
+;   it under the terms of the GNU General Public License as published by
+;   the Free Software Foundation; either version 2 of the License, or
+;   (at your option) any later version.
+;
+;   This program is distributed in the hope that it will be useful,
+;   but WITHOUT ANY WARRANTY; without even the implied warranty of
+;   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+;   GNU General Public License for more details.
+;
+;   You should have received a copy of the GNU General Public License
+;   along with this program; if not, write to the Free Software
+;   Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+;
+;
+; Firmware: usbduxfast_firmware.asm for usbdux.c
+; Description: Firmware for usbduxfast
+; Devices: [ITL] USB-DUX (usbdux.o)
+; Author: Bernd Porr <Bernd.Porr@f2s.com>
+; Updated: 17 Apr 2009
+; Status: stable
+;
+;;;
+;;;
+;;;
+
+	.inc	fx2-include.asm
+
+	.equ	WFLOADED,70H	; waveform is loaded
+
+	.org	0000h		; after reset the processor starts here
+	ljmp	main		; jump to the main loop
+
+	.org	0043h		; the IRQ2-vector
+	ljmp	jmptbl		; irq service-routine
+
+	.org	0100h		; start of the jump table
+
+jmptbl:	ljmp	sudav_isr
+	nop
+	ljmp	sof_isr
+	nop
+	ljmp	sutok_isr
+	nop
+	ljmp	suspend_isr
+	nop
+	ljmp	usbreset_isr
+	nop
+	ljmp	hispeed_isr
+	nop
+	ljmp	ep0ack_isr
+	nop
+	ljmp	spare_isr
+	nop
+	ljmp	ep0in_isr
+	nop
+	ljmp	ep0out_isr
+	nop
+	ljmp	ep1in_isr
+	nop
+	ljmp	ep1out_isr
+	nop
+	ljmp	ep2_isr
+	nop
+	ljmp	ep4_isr
+	nop
+	ljmp	ep6_isr
+	nop
+	ljmp	ep8_isr
+	nop
+	ljmp	ibn_isr
+	nop
+	ljmp	spare_isr
+	nop
+	ljmp	ep0ping_isr
+	nop
+	ljmp	ep1ping_isr
+	nop
+	ljmp	ep2ping_isr
+	nop
+	ljmp	ep4ping_isr
+	nop
+	ljmp	ep6ping_isr
+	nop
+	ljmp	ep8ping_isr
+	nop
+	ljmp	errlimit_isr
+	nop
+	ljmp	spare_isr
+	nop
+	ljmp	spare_isr
+	nop
+	ljmp	spare_isr
+	nop
+	ljmp	ep2isoerr_isr
+	nop
+	ljmp	ep4isoerr_isr
+	nop
+	ljmp	ep6isoerr_isr
+	nop
+	ljmp	ep8isoerr_isr
+
+	
+	;; dummy isr
+sof_isr:
+sudav_isr:	
+sutok_isr:	
+suspend_isr:	
+usbreset_isr:	
+hispeed_isr:	
+ep0ack_isr:	
+spare_isr:	
+ep0in_isr:	
+ep0out_isr:	
+ep1out_isr:
+ep1in_isr:	
+ibn_isr:	
+ep0ping_isr:	
+ep1ping_isr:	
+ep2ping_isr:	
+ep4ping_isr:	
+ep6ping_isr:	
+ep8ping_isr:	
+errlimit_isr:	
+ep2isoerr_isr:	
+ep4isoerr_isr:	
+ep6isoerr_isr:	
+ep8isoerr_isr:
+ep6_isr:
+ep2_isr:
+ep8_isr:
+
+	push	dps
+	push	dpl
+	push	dph
+	push	dpl1
+	push	dph1
+	push	acc
+	push	psw
+
+	;; clear the USB2 irq bit and return
+	mov	a,EXIF
+	clr	acc.4
+	mov	EXIF,a
+
+	pop	psw
+	pop	acc 
+	pop	dph1 
+	pop	dpl1
+	pop	dph 
+	pop	dpl 
+	pop	dps
+	
+	reti
+
+		
+;;; main program
+;;; basically only initialises the processor and
+;;; then engages in an endless loop
+main:
+	mov	dptr,#REVCTL
+	mov	a,#00000011b	; allows skip
+	lcall	syncdelaywr
+
+	mov	DPTR,#CPUCS	; CPU control register
+	mov	a,#00010000b	; 48Mhz
+	lcall	syncdelaywr
+
+	mov	dptr,#IFCONFIG	; switch on IFCLK signal
+	mov	a,#10100010b	; gpif, 30MHz
+	lcall	syncdelaywr
+
+	mov	dptr,#FIFORESET
+	mov	a,#80h
+	lcall	syncdelaywr
+	mov	a,#8
+	lcall	syncdelaywr
+	mov	a,#2		
+	lcall	syncdelaywr
+	mov	a,#4		
+	lcall	syncdelaywr
+	mov	a,#6		
+	lcall	syncdelaywr
+	mov	a,#0		
+	lcall	syncdelaywr
+
+	mov	dptr,#INTSETUP	; IRQ setup register
+	mov	a,#08h		; enable autovector
+	lcall	syncdelaywr
+
+	lcall	initeps		; init the isochronous data-transfer
+
+	lcall	initGPIF
+
+;;; main loop
+
+mloop2:
+	lcall	gpif_run
+	sjmp	mloop2		; do nothing. The rest is done by the IRQs
+
+
+gpif_run:
+	mov	a,WFLOADED
+	jz	no_trig		; do not trigger
+	mov	a,GPIFTRIG	; GPIF status
+	anl	a,#80h		; done bit
+	jz	no_trig		; GPIF busy
+
+;;; gpif has stopped
+	mov	a,#06h		; RD,EP6
+	mov	GPIFTRIG,a
+no_trig:
+	ret
+
+	
+
+initGPIF:
+	mov	DPTR,#EP6CFG	; BLK data from here to the host
+	mov	a,#11100000b	; Valid, quad buffering
+	lcall	syncdelaywr	; write
+
+	mov	dptr,#EP6FIFOCFG
+	mov	a,#00001001b	; autoin, wordwide
+	lcall	syncdelaywr
+
+	mov	dptr,#EP6AUTOINLENH
+	mov	a,#00000010b	; 512 bytes
+	lcall	syncdelaywr	; write
+
+	mov	dptr,#EP6AUTOINLENL
+	mov	a,#00000000b	; 0
+	lcall	syncdelaywr	; write
+
+	mov	dptr,#GPIFWFSELECT
+	mov	a,#11111100b	; waveform 0 for FIFO RD
+	lcall	syncdelaywr
+
+	mov	dptr,#GPIFCTLCFG
+	mov	a,#10000000b	; tri state for CTRL
+	lcall	syncdelaywr
+
+	mov	dptr,#GPIFIDLECTL
+	mov	a,#11111111b	; all CTL outputs high
+	lcall	syncdelaywr
+	mov	a,#11111101b	; reset counter
+	lcall	syncdelaywr
+	mov	a,#11111111b	; reset to high again
+	lcall	syncdelaywr
+
+	mov	a,#00000010b	; abort when full
+	mov	dptr,#EP6GPIFFLGSEL
+	lcall	syncdelaywr
+
+	mov	a,#00000001b	; stop when buffer overfl
+	mov	dptr,#EP6GPIFPDFSTOP
+	lcall	syncdelaywr
+
+	mov	a,#0
+	mov	dptr,#GPIFREADYCFG
+	lcall	syncdelaywr
+
+	mov	a,#0
+	mov	dptr,#GPIFIDLECS
+	lcall	syncdelaywr
+
+; waveform 1
+; this is a dummy waveform which is used
+; during the upload of another waveform into
+; wavefrom 0
+; it branches directly into the IDLE state
+	mov	dptr,#0E420H
+	mov	a,#00111111b	; branch to IDLE
+	lcall	syncdelaywr
+
+	mov	dptr,#0E428H	; opcode
+	mov	a,#00000001b	; deceision point
+	lcall	syncdelaywr
+
+	mov	dptr,#0E430H
+	mov	a,#0FFH		; output is high
+	lcall	syncdelaywr
+
+	mov	dptr,#0E438H
+	mov	a,#0FFH		; logic function
+	lcall	syncdelaywr
+
+; signals that no waveform 0 is loaded so far
+	mov	WFLOADED,#0	; waveform flag
+
+	ret
+
+
+
+;;; initilise the transfer
+;;; It is assumed that the USB interface is in alternate setting 1
+initeps:
+	mov	DPTR,#EP4CFG
+	mov	a,#10100000b	; valid, bulk, out
+	lcall	syncdelaywr
+
+	mov	dptr,#EP4BCL	; "arm" it
+	mov	a,#00h
+	lcall	syncdelaywr	; wait until we can write again
+	lcall	syncdelaywr	; wait
+	lcall	syncdelaywr	; wait
+
+	mov	DPTR,#EP8CFG
+	mov	a,#0		; disable EP8, it overlaps with EP6!!
+	lcall	syncdelaywr
+
+	mov	dptr,#EPIE	; interrupt enable
+	mov	a,#00100000b	; enable irq for ep4
+	lcall	syncdelaywr	; do it
+
+	mov	dptr,#EPIRQ	; clear IRQs
+	mov	a,#00100100b
+	movx	@dptr,a
+
+        mov     DPTR,#USBIE	; USB int enable register
+        mov     a,#0            ; SOF etc
+        movx    @DPTR,a         ;
+
+        mov     DPTR,#GPIFIE	; GPIF int enable register
+        mov     a,#0            ; done IRQ
+        movx    @DPTR,a         ;
+
+	mov	EIE,#00000001b	; enable INT2 in the 8051's SFR
+	mov	IE,#80h		; IE, enable all interrupts
+
+	ret
+
+
+;;; interrupt-routine for ep4
+;;; receives the channel list and other commands
+ep4_isr:
+	push	dps
+	push	dpl
+	push	dph
+	push	dpl1
+	push	dph1
+	push	acc
+	push	psw
+	push	00h		; R0
+	push	01h		; R1
+	push	02h		; R2
+	push	03h		; R3
+	push	04h		; R4
+	push	05h		; R5
+	push	06h		; R6
+	push	07h		; R7
+		
+	mov	dptr,#0f400h	; FIFO buffer of EP4
+	movx	a,@dptr		; get the first byte
+
+	mov	dptr,#ep4_jmp	; jump table for the different functions
+	rl	a		; multiply by 2: sizeof sjmp
+	jmp	@a+dptr		; jump to the jump table
+
+ep4_jmp:
+	sjmp	storewaveform	; a=0
+	sjmp	init_ep6	; a=1
+	
+init_ep6:
+	; stop ep6
+	; just now do nothing
+
+	ljmp	over_wf
+
+
+storewaveform:
+	mov	WFLOADED,#0	; waveform flag
+
+	mov	dptr,#EP6FIFOCFG
+	mov	a,#00000000b	;
+	lcall	syncdelaywr
+
+	mov	dptr,#GPIFABORT
+	mov	a,#0ffh		; abort all transfers
+	lcall	syncdelaywr
+
+wait_f_abort:
+	mov	a,GPIFTRIG	; GPIF status
+	anl	a,#80h		; done bit
+	jz	wait_f_abort	; GPIF busy
+
+	mov	dptr,#GPIFWFSELECT
+	mov	a,#11111101b	; select dummy waveform
+	movx	@dptr,a
+	lcall	syncdelay
+
+	mov	dptr,#FIFORESET
+	mov	a,#80h		; NAK
+	lcall	syncdelaywr
+	mov	a,#6		; reset EP6
+	lcall	syncdelaywr
+	mov	a,#0		; normal op
+	lcall	syncdelaywr
+
+; change to dummy waveform 1
+	mov	a,#06h		; RD,EP6
+	mov	GPIFTRIG,a
+
+; wait a bit
+	mov	r2,255
+loopx:
+	djnz	r2,loopx
+
+; abort waveform if not already so
+	mov	dptr,#GPIFABORT
+	mov	a,#0ffh		; abort all transfers
+	lcall	syncdelaywr
+
+; wait again
+	mov	r2,255
+loopx2:
+	djnz	r2,loopx2
+
+; check for DONE
+wait_f_abort2:
+	mov	a,GPIFTRIG	; GPIF status
+	anl	a,#80h		; done bit
+	jz	wait_f_abort2	; GPIF busy
+
+; upload the new waveform into waveform 0
+	mov	AUTOPTRH2,#0E4H	; XDATA0H
+	lcall	syncdelay
+	mov	AUTOPTRL2,#00H	; XDATA0L
+	lcall	syncdelay
+
+	mov	AUTOPTRH1,#0F4H	; EP4 high
+	lcall	syncdelay
+	mov	AUTOPTRL1,#01H	; EP4 low
+	lcall	syncdelay
+
+	mov	AUTOPTRSETUP,#7	; autoinc and enable
+	lcall	syncdelay
+
+	mov 	r2,#20H		; 32 bytes to transfer
+
+wavetr:
+	mov 	dptr,#XAUTODAT1
+	movx	a,@dptr
+	lcall	syncdelay
+	mov	dptr,#XAUTODAT2
+	movx	@dptr,a
+	lcall	syncdelay
+	djnz	r2,wavetr
+
+	mov	dptr,#EP6FIFOCFG
+	mov	a,#00001001b	; autoin, wordwide
+	lcall	syncdelaywr
+
+	mov	dptr,#GPIFWFSELECT
+	mov	a,#11111100b
+	movx	@dptr,a
+	lcall	syncdelay
+
+	mov	dptr,#FIFORESET
+	mov	a,#80h		; NAK
+	lcall	syncdelaywr
+	mov	a,#6		; reset EP6
+	lcall	syncdelaywr
+	mov	a,#0		; normal op
+	lcall	syncdelaywr
+
+	mov	dptr,#0E400H+10H; waveform 0: first CTL byte
+	movx	a,@dptr		; get it
+	orl	a,#11111011b	; force all bits to one except the range bit
+	mov	dptr,#GPIFIDLECTL
+	lcall	syncdelaywr
+
+	mov	WFLOADED,#1	; waveform flag
+
+; do the common things here	
+over_wf:	
+	mov	dptr,#EP4BCL
+	mov	a,#00h
+	movx	@DPTR,a		; arm it
+	lcall	syncdelay	; wait
+	movx	@DPTR,a		; arm it
+	lcall	syncdelay	; wait
+
+	;; clear INT2
+	mov	a,EXIF		; FIRST clear the USB (INT2) interrupt request
+	clr	acc.4
+	mov	EXIF,a		; Note: EXIF reg is not 8051 bit-addressable
+
+	mov	DPTR,#EPIRQ	; 
+	mov	a,#00100000b	; clear the ep4irq
+	movx	@DPTR,a
+
+	pop	07h
+	pop	06h
+	pop	05h
+	pop	04h		; R4
+	pop	03h		; R3
+	pop	02h		; R2
+	pop	01h		; R1
+	pop	00h		; R0
+	pop	psw
+	pop	acc 
+	pop	dph1 
+	pop	dpl1
+	pop	dph 
+	pop	dpl 
+	pop	dps
+	reti
+
+
+;; need to delay every time the byte counters
+;; for the EPs have been changed.
+
+syncdelay:
+	nop
+	nop
+	nop
+	nop
+	nop
+	nop
+	nop
+	nop
+	nop
+	ret
+
+
+syncdelaywr:
+	lcall	syncdelay
+	movx	@dptr,a
+	ret
+
+
+.End
+
+
+
+
+
+
+
+
+
+
+
+
diff --git a/usbdux/usbduxsigma_firmware.asm b/usbdux/usbduxsigma_firmware.asm
new file mode 100644
index 0000000..38f5f0e
--- /dev/null
+++ b/usbdux/usbduxsigma_firmware.asm
@@ -0,0 +1,1394 @@
+;   usbdux_firmware.asm
+;   Copyright (C) 2010,2015 Bernd Porr, mail@berndporr.me.uk
+;   For usbduxsigma.c 0.5+
+;
+;   This program is free software; you can redistribute it and/or modify
+;   it under the terms of the GNU General Public License as published by
+;   the Free Software Foundation; either version 2 of the License, or
+;   (at your option) any later version.
+;
+;   This program is distributed in the hope that it will be useful,
+;   but WITHOUT ANY WARRANTY; without even the implied warranty of
+;   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+;   GNU General Public License for more details.
+;
+;   You should have received a copy of the GNU General Public License
+;   along with this program; if not, write to the Free Software
+;   Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
+;
+;
+; Firmware: usbduxsigma_firmware.asm for usbduxsigma.c
+; Description: University of Stirling USB DAQ & INCITE Technology Limited
+; Devices: [ITL] USB-DUX-SIGMA (usbduxsigma.ko)
+; Author: Bernd Porr <mail@berndporr.me.uk>
+; Updated: 20 Jul 2015
+; Status: testing
+;
+;;;
+;;;
+;;;
+	
+	.inc	fx2-include.asm
+
+;;; a couple of flags in high memory
+	.equ	CMD_FLAG,80h	; flag for the next in transfer
+	.equ	PWMFLAG,81h	; PWM on or off?
+	.equ	MAXSMPL,82H	; maximum number of samples, n channellist
+	.equ	MUXSG0,83H	; content of the MUXSG0 register
+	.equ	INTERVAL,88h	; uframe/frame interval
+	.equ	INTCTR,89h	; interval counter
+	.equ	DABUFFER,0F0h	; buffer with DA values
+
+;;; in precious low memory but accessible within one clock cycle
+	.equ	DPTRL,70H
+	.equ	DPTRH,71h
+	.equ	ASYNC_ON,72h
+	.equ	SMPLCTR,73h
+
+;;; actual code
+	.org	0000h		; after reset the processor starts here
+	ljmp	main		; jump to the main loop
+
+	.org	0003h
+	ljmp	isr0		; external interrupt 0: /DRY
+
+	.org	0043h		; the IRQ2-vector
+	ljmp	jmptbl		; irq service-routine
+
+	.org	0100h		; start of the jump table
+
+jmptbl:	ljmp	sudav_isr
+	nop
+	ljmp	sof_isr
+	nop
+	ljmp	sutok_isr
+	nop
+	ljmp	suspend_isr
+	nop
+	ljmp	usbreset_isr
+	nop
+	ljmp	hispeed_isr
+	nop
+	ljmp	ep0ack_isr
+	nop
+	ljmp	spare_isr
+	nop
+	ljmp	ep0in_isr
+	nop
+	ljmp	ep0out_isr
+	nop
+	ljmp	ep1in_isr
+	nop
+	ljmp	ep1out_isr
+	nop
+	ljmp	ep2_isr
+	nop
+	ljmp	ep4_isr
+	nop
+	ljmp	ep6_isr
+	nop
+	ljmp	ep8_isr
+	nop
+	ljmp	ibn_isr
+	nop
+	ljmp	spare_isr
+	nop
+	ljmp	ep0ping_isr
+	nop
+	ljmp	ep1ping_isr
+	nop
+	ljmp	ep2ping_isr
+	nop
+	ljmp	ep4ping_isr
+	nop
+	ljmp	ep6ping_isr
+	nop
+	ljmp	ep8ping_isr
+	nop
+	ljmp	errlimit_isr
+	nop
+	ljmp	spare_isr
+	nop
+	ljmp	spare_isr
+	nop
+	ljmp	spare_isr
+	nop
+	ljmp	ep2isoerr_isr
+	nop
+	ljmp	ep4isoerr_isr
+	nop
+	ljmp	ep6isoerr_isr
+	nop
+	ljmp	ep8isoerr_isr
+
+	
+	;; dummy isr
+sudav_isr:	
+sutok_isr:	
+suspend_isr:	
+usbreset_isr:	
+hispeed_isr:	
+ep0ack_isr:	
+spare_isr:	
+ep0in_isr:	
+ep0out_isr:	
+ibn_isr:	
+ep0ping_isr:	
+ep1ping_isr:	
+ep2ping_isr:	
+ep4ping_isr:	
+ep6ping_isr:	
+ep8ping_isr:	
+errlimit_isr:	
+ep2isoerr_isr:	
+ep4isoerr_isr:	
+ep6isoerr_isr:	
+ep8isoerr_isr:
+ep6_isr:
+ep2_isr:
+ep4_isr:	
+
+	push	dps
+	push	dpl
+	push	dph
+	push	dpl1
+	push	dph1
+	push	acc
+	push	psw
+
+	;; clear the USB2 irq bit and return
+	mov	a,EXIF
+	clr	acc.4
+	mov	EXIF,a
+
+	pop	psw
+	pop	acc 
+	pop	dph1 
+	pop	dpl1
+	pop	dph 
+	pop	dpl 
+	pop	dps
+	
+	reti
+
+
+ep1in_isr:	
+	push	dps
+	push	dpl
+	push	dph
+	push	dpl1
+	push	dph1
+	push	acc
+	push	psw
+		
+	mov	dptr,#0E7C0h	; EP1in
+	mov	a,IOB		; get DIO D
+	movx	@dptr,a		; store it
+	inc	dptr		; next byte
+	mov	a,IOC		; get DIO C
+	movx	@dptr,a		; store it
+	inc	dptr		; next byte
+	mov	a,IOD		; get DIO B
+	movx	@dptr,a		; store it
+	inc	dptr		; next byte
+	mov	a,#0		; just zero
+	movx	@dptr,a		; pad it up
+
+	;; clear INT2
+	mov	a,EXIF		; FIRST clear the USB (INT2) interrupt request
+	clr	acc.4
+	mov	EXIF,a		; Note: EXIF reg is not 8051 bit-addressable
+
+	mov	DPTR,#EPIRQ	; 
+	mov	a,#00000100b	; clear the ep1in
+	movx	@DPTR,a
+
+	pop	psw
+	pop	acc 
+	pop	dph1 
+	pop	dpl1
+	pop	dph 
+	pop	dpl 
+	pop	dps
+	reti
+
+
+
+;;; this is triggered when DRY goes low
+isr0:	
+	push	dps
+	push	dpl
+	push	dph
+	push	dpl1
+	push	dph1
+	push	acc
+	push	psw
+	push	00h		; R0
+	push	01h		; R1
+	push	02h		; R2
+	push	03h		; R3
+	push	04h		; R4
+	push	05h		; R5
+	push	06h		; R6
+	push	07h		; R7
+
+	mov	a,ASYNC_ON
+	jz	noepsubmit
+
+	mov	DPS,#0
+	mov	dpl,DPTRL
+	mov	dph,DPTRH
+
+	lcall	readADCch	; read one channel
+
+	mov	DPTRL,dpl
+	mov	DPTRH,dph
+
+	mov	a,SMPLCTR
+	dec	a
+	mov	SMPLCTR,a
+	jnz	noepsubmit
+
+	mov	ASYNC_ON,#0
+
+	clr	IOA.7		; START = 0
+	
+	;; arm the endpoint and send off the data
+	mov	DPTR,#EP6BCH	; byte count H
+	mov	a,#0		; is zero
+	lcall	syncdelaywr	; wait until we can write again
+	
+	mov	r0,#MAXSMPL	; number of samples to transmit
+	mov	a,@r0		; get them
+	rl	a		; a=a*2
+	rl	a		; a=a*2
+	add	a,#4		; four bytes for DIO
+	mov	DPTR,#EP6BCL	; byte count L
+	lcall	syncdelaywr	; wait until we can write again
+
+noepsubmit:
+	pop	07h
+	pop	06h
+	pop	05h
+	pop	04h		; R4
+	pop	03h		; R3
+	pop	02h		; R2
+	pop	01h		; R1
+	pop	00h		; R0
+	pop	psw
+	pop	acc 
+	pop	dph1 
+	pop	dpl1
+	pop	dph 
+	pop	dpl 
+	pop	dps
+
+	reti
+
+	
+		
+;;; main program
+;;; basically only initialises the processor and
+;;; then engages in an endless loop
+main:
+	mov	DPTR,#CPUCS	; CPU control register
+	mov	a,#00010000b	; 48Mhz
+	lcall	syncdelaywr
+
+        mov     dptr,#REVCTL
+        mov     a,#00000011b    ; allows skip
+        lcall   syncdelaywr
+
+	mov	dptr,#INTSETUP	; IRQ setup register
+	mov	a,#08h		; enable autovector
+	lcall	syncdelaywr
+
+	mov	dptr,#PORTCCFG
+	mov	a,#0
+	lcall	syncdelaywr
+
+	mov	IP,#01H		; int0 has highest interrupt priority
+	mov	EIP,#0		; all USB interrupts have low priority
+
+	lcall	initAD		; init the ports to the converters
+
+	lcall	initeps		; init the isochronous data-transfer
+
+;;; main loop, rest is done as interrupts
+mloop2:	nop
+
+;;; pwm
+	mov	r0,#PWMFLAG	; pwm on?
+	mov	a,@r0		; get info
+	jz	mloop2		; it's off
+
+	mov	a,GPIFTRIG	; GPIF status
+	anl	a,#80h		; done bit
+	jz	mloop2		; GPIF still busy
+
+        mov     a,#01h		; WR,EP4, 01 = EP4
+        mov     GPIFTRIG,a	; restart it
+
+	sjmp	mloop2		; loop for ever
+
+
+;;; initialise the ports for the AD-converter
+initAD:
+	mov	r0,#MAXSMPL	; length of channellist
+	mov	@r0,#0		; we don't want to accumlate samples
+
+	mov	ASYNC_ON,#0	; async enable
+
+	mov	r0,#DABUFFER
+	mov	@r0,#0
+
+	mov	OEA,#11100000b	; PortA7,A6,A5 Outputs
+	mov	IOA,#01100000b	; /CS = 1 and START = 0
+	mov	dptr,#IFCONFIG	; switch on clock on IFCLK pin
+	mov	a,#10100000b	; gpif, 30MHz, internal IFCLK -> 15MHz for AD
+	lcall	syncdelaywr
+
+	mov	SCON0,#013H	; ser rec en, TX/RX: stop, 48/12MHz=4MHz clock
+	
+	mov	dptr,#PORTECFG
+	mov	a,#00001000b	; special function for port E: RXD0OUT
+	lcall	syncdelaywr
+
+	ret
+
+
+;;; send a byte via SPI
+;;; content in a, dptr1 is changed
+;;; the lookup is done in dptr1 so that the normal dptr is not affected
+;;; important: /cs needs to be reset to 1 by the caller: IOA.5
+sendSPI:
+	inc	DPS
+	
+	;; bit reverse
+	mov	dptr,#swap_lut	; lookup table
+	movc 	a,@a+dptr	; reverse bits
+
+	;; clear interrupt flag, is used to detect
+	;; successful transmission
+	clr	SCON0.1		; clear interrupt flag
+
+	;; start transmission by writing the byte
+	;; in the transmit buffer
+	mov	SBUF0,a		; start transmission
+
+	;; wait for the end of the transmission
+sendSPIwait:
+	mov	a,SCON0		; get transmission status
+	jnb     ACC.1,sendSPIwait	; loop until transmitted
+
+	inc	DPS
+	
+	ret
+
+
+
+	
+;;; receive a byte via SPI
+;;; content in a, dptr is changed
+;;; the lookup is done in dptr1 so that the normal dptr is not affected
+;;; important: the /CS needs to be set to 1 by the caller via "setb IOA.5"
+recSPI:
+	inc	DPS
+	
+	clr	IOA.5		; /cs to 0	
+
+	;; clearning the RI bit starts reception of data
+	clr	SCON0.0
+
+recSPIwait:
+	;; RI goes back to 1 after the reception of the 8 bits
+	mov	a,SCON0		; get receive status
+	jnb	ACC.0,recSPIwait; loop until all bits received
+
+	;; read the byte from the buffer
+	mov	a,SBUF0		; get byte
+	
+	;; lookup: reverse the bits
+	mov	dptr,#swap_lut	; lookup table
+	movc 	a,@a+dptr	; reverse the bits
+
+	inc	DPS
+	
+	ret
+
+
+
+	
+;;; reads a register
+;;; register address in a
+;;; returns value in a
+registerRead:
+	anl	a,#00001111b	; mask out the index to the register
+	orl	a,#01000000b	; 010xxxxx indicates register read
+	clr	IOA.5		; ADC /cs to 0
+	lcall	sendSPI		; send the command over
+	lcall	recSPI		; read the contents back
+	setb	IOA.5		; ADC /cs to 1
+	ret
+
+
+
+;;; writes to a register
+;;; register address in a
+;;; value in r0
+registerWrite:
+	push	acc
+	anl	a,#00001111b	; mask out the index to the register
+	orl	a,#01100000b	; 011xxxxx indicates register write
+
+	clr	IOA.5		; ADC /cs to 0	
+
+	lcall	sendSPI		;
+	mov	a,r0
+	lcall	sendSPI
+
+	setb	IOA.5		; ADC /cs to 1
+	pop	acc
+
+	lcall	registerRead	; check if the data has arrived in the ADC
+	mov	0f0h,r0		; register B
+	cjne	a,0f0h,registerWrite ; something went wrong, try again
+	
+	ret
+
+
+
+;;; initilise the endpoints
+initeps:
+	mov	dptr,#FIFORESET
+	mov	a,#80H		
+	movx	@dptr,a		; reset all fifos
+	mov	a,#2	
+	movx	@dptr,a		; 
+	mov	a,#4		
+	movx	@dptr,a		; 
+	mov	a,#6		
+	movx	@dptr,a		; 
+	mov	a,#8		
+	movx	@dptr,a		; 
+	mov	a,#0		
+	movx	@dptr,a		; normal operat
+	
+	mov	DPTR,#EP2CFG
+	mov	a,#10010010b	; valid, out, double buff, iso
+	movx	@DPTR,a
+
+	mov	dptr,#EP2FIFOCFG
+	mov	a,#00000000b	; manual
+	movx	@dptr,a
+
+	mov	dptr,#EP2BCL	; "arm" it
+	mov	a,#00h
+	movx	@DPTR,a		; can receive data
+	lcall	syncdelay	; wait to sync
+	movx	@DPTR,a		; can receive data
+	lcall	syncdelay	; wait to sync
+	movx	@DPTR,a		; can receive data
+	lcall	syncdelay	; wait to sync
+	
+	mov	DPTR,#EP1OUTCFG
+	mov	a,#10100000b	; valid
+	movx	@dptr,a
+
+	mov	dptr,#EP1OUTBC	; "arm" it
+	mov	a,#00h
+	movx	@DPTR,a		; can receive data
+	lcall	syncdelay	; wait until we can write again
+	movx	@dptr,a		; make shure its really empty
+	lcall	syncdelay	; wait
+
+	mov	DPTR,#EP6CFG	; ISO data from here to the host
+	mov	a,#11010010b	; Valid
+	movx	@DPTR,a		; ISO transfer, double buffering
+
+	mov	DPTR,#EP8CFG	; EP8
+	mov	a,#11100000b	; BULK data from here to the host
+	movx	@DPTR,a		;
+
+	mov	dptr,#PORTACFG
+	mov	a,#1		; interrupt on pin A0
+	lcall	syncdelaywr
+
+	;; enable interrupts
+	mov	dptr,#EPIE	; interrupt enable
+	mov	a,#10001100b	; enable irq for ep1out,8,ep1in
+	movx	@dptr,a		; do it
+
+	mov	dptr,#EPIRQ	; clear IRQs
+	mov	a,#10001100b
+	movx	@dptr,a
+	
+        mov     DPTR,#USBIE	; USB int enables register
+        mov     a,#2            ; enables SOF (1ms/125us interrupt)
+        movx    @DPTR,a         ; 
+
+	setb	TCON.0		; make INT0 edge triggered, falling edge
+
+	mov	EIE,#00000001b	; enable INT2/USBINT in the 8051's SFR
+	mov	IE,#81h		; IE, enable all interrupts and INT0
+
+	ret
+
+
+;;; Reads one ADC channel from the converter and stores
+;;; the result at dptr
+readADCch:
+	;; reading data is done by just dropping /CS and start reading and
+	;; while keeping the IN signal to the ADC inactive
+	clr	IOA.5		; /cs to 0
+	
+	;; 1st byte: STATUS
+	lcall	recSPI		; index
+	movx	@dptr,a		; store the byte
+	inc	dptr		; increment pointer
+
+	;; 2nd byte: MSB
+	lcall	recSPI		; data
+	movx	@dptr,a
+	inc	dptr
+
+	;; 3rd byte: MSB-1
+	lcall	recSPI		; data
+	movx	@dptr,a
+	inc	dptr
+
+	;; 4th byte: LSB
+	lcall	recSPI		; data
+	movx	@dptr,a
+	inc	dptr
+	
+	;; got all bytes
+	setb	IOA.5		; /cs to 1
+	
+	ret
+
+	
+
+;;; interrupt-routine for SOF
+sof_isr:
+	push	dps
+	push	dpl
+	push	dph
+	push	dpl1
+	push	dph1
+	push	acc
+	push	psw
+	push	00h		; R0
+	push	01h		; R1
+	push	02h		; R2
+	push	03h		; R3
+	push	04h		; R4
+	push	05h		; R5
+	push	06h		; R6
+	push	07h		; R7
+
+	mov	r0,#INTCTR	; interval counter
+	mov	a,@r0		; get the value
+	dec	a		; decrement
+	mov	@r0,a		; save it again
+	jz	sof_adc		; we do ADC functions
+	ljmp	epfull		; we skip all adc functions
+	
+sof_adc:
+	mov	r1,#INTERVAL	; get the interval
+	mov	a,@r1		; get it
+	mov	@r0,a		; save it in the counter
+	mov	a,EP2468STAT
+	anl	a,#20H		; full?
+	jnz	epfull		; EP6-buffer is full
+
+	mov	a,IOA		; conversion running?
+	jb	ACC.7,epfull
+
+	;; make sure that we are starting with the first channel
+	mov	r0,#MUXSG0	;
+	mov	a,@r0		; get config of MUXSG0
+	mov	r0,a
+	mov	a,#04H		; MUXSG0
+	lcall	registerWrite	; this resets the channel sequence
+
+	setb	IOA.7		; start converter, START = 1
+	
+	mov	dptr,#0f800h	; EP6 buffer
+	mov	a,IOD		; get DIO D
+	movx	@dptr,a		; store it
+	inc	dptr		; next byte
+	mov	a,IOC		; get DIO C
+	movx	@dptr,a		; store it
+	inc	dptr		; next byte
+	mov	a,IOB		; get DIO B
+	movx	@dptr,a		; store it
+	inc	dptr		; next byte
+	mov	a,#0		; just zero
+	movx	@dptr,a		; pad it up
+	inc	dptr		; algin along a 32 bit word
+	mov	DPTRL,dpl
+	mov	DPTRH,dph
+
+	mov	r0,#MAXSMPL
+	mov	a,@r0
+	mov	SMPLCTR,a
+
+	mov	ASYNC_ON,#1
+
+epfull:
+	;; do the D/A conversion
+	mov	a,EP2468STAT
+	anl	a,#01H		; empty
+	jnz	epempty		; nothing to get
+
+	mov	dptr,#0F000H	; EP2 fifo buffer
+	lcall	dalo		; conversion
+
+	mov	dptr,#EP2BCL	; "arm" it
+	mov	a,#00h
+	lcall	syncdelaywr	; wait for the rec to sync
+	lcall	syncdelaywr	; wait for the rec to sync
+
+epempty:
+	mov	a,IOA		; conversion running?
+	jb	ACC.7,sofend
+
+	lcall	DAsend
+
+sofend:	
+	;; clear INT2
+	mov	a,EXIF		; FIRST clear the USB (INT2) interrupt request
+	clr	acc.4
+	mov	EXIF,a		; Note: EXIF reg is not 8051 bit-addressable
+	
+	mov	DPTR,#USBIRQ	; points to the SOF
+	mov	a,#2		; clear the SOF
+	movx	@DPTR,a
+
+nosof:
+	pop	07h
+	pop	06h
+	pop	05h
+	pop	04h		; R4
+	pop	03h		; R3
+	pop	02h		; R2
+	pop	01h		; R1
+	pop	00h		; R0
+	pop	psw
+	pop	acc 
+	pop	dph1 
+	pop	dpl1
+	pop	dph 
+	pop	dpl 
+	pop	dps
+	reti
+
+
+reset_ep8:
+	;; erase all data in ep8
+	mov	dptr,#FIFORESET
+	mov	a,#80H		; NAK
+	lcall	syncdelaywr
+	mov	dptr,#FIFORESET
+	mov	a,#8		; reset EP8
+	lcall	syncdelaywr
+	mov	dptr,#FIFORESET
+	mov	a,#0		; normal operation
+	lcall	syncdelaywr
+	ret
+
+
+reset_ep6:
+	;; throw out old data
+	mov	dptr,#FIFORESET
+	mov	a,#80H		; NAK
+	lcall	syncdelaywr
+	mov	dptr,#FIFORESET
+	mov	a,#6		; reset EP6
+	lcall	syncdelaywr
+	mov	dptr,#FIFORESET
+	mov	a,#0		; normal operation
+	lcall	syncdelaywr
+	ret
+
+
+;;; configure the ADC converter
+;;; the dptr points to the init data:
+;;; CONFIG 0,1,3,4,5,6
+;;; note that CONFIG2 is omitted
+configADC:	
+	clr	IOA.7		; stops ADC: START line of ADC = L
+	setb	IOA.5		; ADC /cs to 1
+
+	;; just in case something has gone wrong
+	nop
+	nop
+	nop
+
+	mov	a,#11000000b	; reset	the ADC
+	clr	IOA.5		; ADC /cs to 0	
+	lcall	sendSPI
+	setb	IOA.5		; ADC /cs to 1	
+
+	movx	a,@dptr		;
+	inc	dptr
+	mov	r0,a
+	mov	a,#00H		; CONFIG0
+	lcall	registerWrite
+
+	movx	a,@dptr		;
+	inc	dptr
+	mov	r0,a
+	mov	a,#01H		; CONFIG1
+	lcall	registerWrite
+
+	movx	a,@dptr		;
+	inc	dptr
+	mov	r0,a
+	mov	a,#03H		; MUXDIF
+	lcall	registerWrite
+
+	movx	a,@dptr		;
+	inc	dptr
+	mov	r0,#MUXSG0
+	mov	@r0,a		; store it for reset purposes
+	mov	r0,a
+	mov	a,#04H		; MUXSG0
+	lcall	registerWrite
+	
+	movx	a,@dptr		;
+	inc	dptr
+	mov	r0,a
+	mov	a,#05H		; MUXSG1
+	lcall	registerWrite
+	
+	movx	a,@dptr		;
+	inc	dptr
+	mov	r0,a
+	mov	a,#06H		; SYSRED
+	lcall	registerWrite
+
+	ret
+
+	
+;;; interrupt-routine for ep1out
+;;; receives the channel list and other commands
+ep1out_isr:
+	push	dps
+	push	dpl
+	push	dph
+	push	dpl1
+	push	dph1
+	push	acc
+	push	psw
+	push	00h		; R0
+	push	01h		; R1
+	push	02h		; R2
+	push	03h		; R3
+	push	04h		; R4
+	push	05h		; R5
+	push	06h		; R6
+	push	07h		; R7
+
+	mov	dptr,#0E780h	; FIFO buffer of EP1OUT
+	movx	a,@dptr		; get the first byte
+	mov	r0,#CMD_FLAG	; pointer to the command byte
+	mov 	@r0,a		; store the command byte for ep8
+
+	mov	dptr,#ep1out_jmp; jump table for the different functions
+	rl	a		; multiply by 2: sizeof sjmp
+	jmp	@a+dptr		; jump to the jump table
+	;; jump table, corresponds to the command bytes defined
+	;; in usbdux.c
+ep1out_jmp:
+	sjmp	startadc	; a=0
+	sjmp	single_da	; a=1
+	sjmp	config_digital_b; a=2
+	sjmp	write_digital_b	; a=3
+	sjmp	initsgADchannel	; a=4
+	sjmp	nothing		; a=5
+	sjmp	nothing		; a=6
+	sjmp	pwm_on		; a=7
+	sjmp	pwm_off		; a=8
+	sjmp	startadcint	; a=9
+
+nothing:
+	ljmp	over_da
+
+pwm_on:
+	lcall	startPWM
+	sjmp	over_da
+
+pwm_off:
+	lcall	stopPWM
+	sjmp	over_da
+
+initsgADchannel:
+	mov	ASYNC_ON,#0
+	
+	mov	dptr,#0e781h	; FIFO buffer of EP1OUT
+	lcall	configADC	; configures the ADC esp sel the channel
+
+	lcall	reset_ep8	; reset FIFO: get rid of old bytes
+	;; Save new A/D data in EP8. This is the first byte
+	;; the host will read during an INSN. If there are
+	;; more to come they will be handled by the ISR of
+	;; ep8.
+	lcall	ep8_ops		; get A/D data
+		
+	sjmp	over_da
+
+startadcint:
+	mov	dptr,#0e781h	; FIFO buffer of EP1OUT from 2nd byte
+
+	movx	a,@dptr		; interval is the 1st byte
+	inc	dptr		; data pointer
+	sjmp	startadc2	; the other paramters as with startadc
+	
+;;; config AD:
+;;; we write to the registers of the A/D converter
+startadc:
+	mov	dptr,#0e781h	; FIFO buffer of EP1OUT from 2nd byte
+
+	mov	a,#1		; interval is 1 here all the time
+startadc2:	
+	mov	r0,#INTERVAL	; set it
+	mov	@r0,a
+	mov	r0,#INTCTR	; the counter is also just one
+	mov	@r0,a
+
+	movx	a,@dptr		; get length of channel list
+	inc	dptr
+	mov	r0,#MAXSMPL
+	mov	@r0,a 		; length of the channel list
+	mov	SMPLCTR,a
+
+	lcall	configADC	; configures all registers
+
+	mov	ASYNC_ON,#1	; async enable
+
+	lcall	reset_ep6	; reset FIFO
+	
+	;; load new A/D data into EP6
+	;; This must be done. Otherwise the ISR is never called.
+	;; The ISR is only called when data has _left_ the
+	;; ep buffer here it has to be refilled.
+	lcall	ep6_arm		; fill with dummy data
+	
+	sjmp	over_da
+
+;;; Single DA conversion. The 2 bytes are in the FIFO buffer
+single_da:
+	mov	dptr,#0e781h	; FIFO buffer of EP1OUT
+	lcall	dalo		; conversion
+	sjmp	over_da
+
+;;; configure the port B as input or output (bitwise)
+config_digital_b:
+	mov	dptr,#0e781h	; FIFO buffer of EP1OUT
+	movx	a,@dptr		; get the second byte
+	inc	dptr
+	mov	OEB,a		; set the output enable bits
+	movx	a,@dptr		; get the second byte
+	inc	dptr
+	mov	OEC,a
+	movx	a,@dptr		; get the second byte
+	inc	dptr
+	mov	OED,a
+	sjmp	over_da
+	
+;;; Write one byte to the external digital port B
+;;; and prepare for digital read
+write_digital_b:
+	mov	dptr,#0e781h	; FIFO buffer of EP1OUT
+	movx	a,@dptr		; command[1]
+	inc	dptr
+	mov	OEB,a		; output enable
+	movx	a,@dptr		; command[2]
+	inc	dptr
+	mov	OEC,a
+	movx	a,@dptr		; command[3]
+	inc	dptr
+	mov	OED,a 
+	movx	a,@dptr		; command[4]
+	inc	dptr
+	mov	IOB,a		;
+	movx	a,@dptr		; command[5]
+	inc	dptr
+	mov	IOC,a
+	movx	a,@dptr		; command[6]
+	inc	dptr
+	mov	IOD,a
+
+	lcall	reset_ep8	; reset FIFO of ep 8
+
+	;; fill ep8 with new data from port B
+	;; When the host requests the data it's already there.
+	;; This must be so. Otherwise the ISR is not called.
+	;; The ISR is only called when a packet has been delivered
+	;; to the host. Thus, we need a packet here in the
+	;; first instance.
+	lcall	ep8_ops		; get digital data
+
+	;; 
+	;; for all commands the same
+over_da:	
+	mov	dptr,#EP1OUTBC
+	mov	a,#00h
+	lcall	syncdelaywr	; arm
+	lcall	syncdelaywr	; arm
+	lcall	syncdelaywr	; arm
+
+	;; clear INT2
+	mov	a,EXIF		; FIRST clear the USB (INT2) interrupt request
+	clr	acc.4
+	mov	EXIF,a		; Note: EXIF reg is not 8051 bit-addressable
+
+	mov	DPTR,#EPIRQ	; 
+	mov	a,#00001000b	; clear the ep1outirq
+	movx	@DPTR,a
+
+	pop	07h
+	pop	06h
+	pop	05h
+	pop	04h		; R4
+	pop	03h		; R3
+	pop	02h		; R2
+	pop	01h		; R1
+	pop	00h		; R0
+	pop	psw
+	pop	acc 
+	pop	dph1 
+	pop	dpl1
+	pop	dph 
+	pop	dpl 
+	pop	dps
+	reti
+
+
+	
+;;; save all DA channels from the endpoint buffer in a local buffer
+dalo:
+	movx	a,@dptr		; number of bytes to send out
+	inc	dptr		; pointer to the first byte
+	mov	r1,#DABUFFER	; buffer for DA values
+	mov	@r1,a		; save it
+	inc	r1		; inc pointer to local buffer
+	mov	r0,a		; counter
+nextDAlo:	
+	movx	a,@dptr		; get the byte
+	inc	dptr		; point to the high byte
+	mov	@r1,a		; save it in the buffer
+	inc	r1
+	movx	a,@dptr		; get the channel number
+	inc	dptr		; get ready for the next channel
+	mov	@r1,a		; save it
+	inc	r1
+	djnz	r0,nextDAlo	; next channel
+	ret
+
+
+;;; write to the DA converter
+DAsend:
+	mov	r1,#DABUFFER	; buffer of the DA values
+	mov	a,@r1		; get the channel count
+	jz	DAret		; nothing to do
+	inc	r1		; pointer to the first byte
+	mov	r0,a		; counter
+nextDA:	
+	mov	a,@r1		; get the byte
+	inc	r1		; point to the high byte
+	mov	r3,a		; store in r3 for writeDA
+	mov	a,@r1		; get the channel number
+	inc	r1		; get ready for the next channel
+	push	1		; is modified in the subroutine
+	lcall	writeDA		; write value to the DAC
+	pop	1		; get the pointer back
+	djnz	r0,nextDA	; next channel
+DAret:	
+	ret
+
+
+
+;;; D/A-conversion:
+;;; channel number in a
+;;; value in r3
+writeDA:
+	anl	a,#00000011b	; 4 channels
+	mov	r1,#6		; the channel number needs to be shifted up
+writeDA2:
+	rl	a		; bit shift to the left
+	djnz	r1,writeDA2	; do it 6 times
+	orl	a,#00010000b	; update outputs after write
+	mov	r2,a		; backup
+	mov	a,r3		; get byte
+	anl	a,#11110000b	; get the upper nibble
+	mov	r1,#4		; shift it up to the upper nibble
+writeDA3:
+	rr	a		; shift to the upper to the lower
+	djnz	r1,writeDA3
+	orl	a,r2		; merge with the channel info
+	clr	IOA.6		; /SYNC (/CS) of the DA to 0
+	lcall	sendSPI		; send it out to the SPI
+	mov	a,r3		; get data again
+	anl	a,#00001111b	; get the lower nibble
+	mov	r1,#4		; shift that to the upper
+writeDA4:
+	rl	a
+	djnz	r1,writeDA4
+	anl	a,#11110000b	; make sure that's empty
+	lcall	sendSPI
+	setb	IOA.6		; /SYNC (/CS) of the DA to 1
+noDA:	ret
+	
+
+
+;;; arm ep6: this is just a dummy arm to get things going
+ep6_arm:
+	mov	DPTR,#EP6BCH	; byte count H
+	mov	a,#0		; is zero
+	lcall	syncdelaywr	; wait until the length has arrived
+	
+	mov	DPTR,#EP6BCL	; byte count L
+	mov	a,#1		; is one
+	lcall	syncdelaywr	; wait until the length has been proc
+	ret
+	
+
+
+;;; converts one analog/digital channel and stores it in EP8
+;;; also gets the content of the digital ports B,C and D depending on
+;;; the COMMAND flag
+ep8_ops:
+	mov	dptr,#0fc01h	; ep8 fifo buffer
+	clr	a		; high byte
+	movx	@dptr,a		; set H=0
+	mov	dptr,#0fc00h	; low byte
+	mov	r0,#CMD_FLAG
+	mov	a,@r0
+	movx	@dptr,a		; save command byte
+
+	mov	dptr,#ep8_jmp	; jump table for the different functions
+	rl	a		; multiply by 2: sizeof sjmp
+	jmp	@a+dptr		; jump to the jump table
+	;; jump table, corresponds to the command bytes defined
+	;; in usbdux.c
+ep8_jmp:
+	sjmp	ep8_err		; a=0, err
+	sjmp	ep8_err		; a=1, err
+	sjmp	ep8_err		; a=2, err
+	sjmp	ep8_dio		; a=3, digital read
+	sjmp	ep8_sglchannel	; a=4, analog A/D
+	sjmp	ep8_err		; a=5, err
+	sjmp	ep8_err		; a=6, err
+
+	;; read one A/D channel
+ep8_sglchannel:
+	setb	IOA.7		; start converter, START = 1
+	;; we do polling: we wait until DATA READY is zero
+sglchwait:	
+	mov	a,IOA		; get /DRDY
+	jb	ACC.0,sglchwait	; wait until data ready (DRDY=0)
+	mov 	DPTR,#0fc01h	; EP8 FIFO
+	lcall	readADCch	; get one reading
+	clr	IOA.7		; stop the converter, START = 0
+
+	sjmp	ep8_send	; send the data
+
+	;; read the digital lines
+ep8_dio:	
+	mov 	DPTR,#0fc01h	; store the contents of port B
+	mov	a,IOB		; in the next
+	movx	@dptr,a		; entry of the buffer
+	inc	dptr
+	mov	a,IOC		; port C
+	movx	@dptr,a		; next byte of the EP
+	inc	dptr
+	mov	a,IOD
+	movx	@dptr,a		; port D
+	
+ep8_send:	
+	mov	DPTR,#EP8BCH	; byte count H
+	mov	a,#0		; is zero
+	lcall	syncdelaywr
+	
+	mov	DPTR,#EP8BCL	; byte count L
+	mov	a,#10H		; 16 bytes, bec it's such a great number...
+	lcall	syncdelaywr	; send the data over to the host
+
+ep8_err:	
+	ret
+
+
+
+;;; EP8 interrupt is the endpoint which sends data back after a command
+;;; The actual command fills the EP buffer already
+;;; but for INSNs we need to deliver more data if the count > 1
+ep8_isr:	
+	push	dps
+	push	dpl
+	push	dph
+	push	dpl1
+	push	dph1
+	push	acc
+	push	psw
+	push	00h		; R0
+	push	01h		; R1
+	push	02h		; R2
+	push	03h		; R3
+	push	04h		; R4
+	push	05h		; R5
+	push	06h		; R6
+	push	07h		; R7
+		
+	lcall	ep8_ops
+	
+	;; clear INT2
+	mov	a,EXIF		; FIRST clear the USB (INT2) interrupt request
+	clr	acc.4
+	mov	EXIF,a		; Note: EXIF reg is not 8051 bit-addressable
+
+	mov	DPTR,#EPIRQ	; 
+	mov	a,#10000000b	; clear the ep8irq
+	movx	@DPTR,a
+
+	pop	07h
+	pop	06h
+	pop	05h
+	pop	04h		; R4
+	pop	03h		; R3
+	pop	02h		; R2
+	pop	01h		; R1
+	pop	00h		; R0
+	pop	psw
+	pop	acc 
+	pop	dph1 
+	pop	dpl1
+	pop	dph 
+	pop	dpl 
+	pop	dps
+	reti
+
+
+
+;;; GPIF waveform for PWM
+waveform:
+	;;      0     1     2     3     4     5     6     7(not used)
+	;; len (gives 50.007Hz)
+	.db	195,  195,  195,  195,  195,  195,  1,    1
+
+	;; opcode
+	.db	002H, 006H, 002H, 002H, 002H, 002H, 002H, 002H
+	
+	;; out
+	.db	0ffH, 0ffH, 0ffH, 0ffH, 0ffH, 0ffH, 0ffH, 0ffH
+
+	;; log
+	.db	000H, 000H, 000H, 000H, 000H, 000H, 000H, 000H
+
+
+stopPWM:
+	mov	r0,#PWMFLAG	; flag for PWM
+	mov	a,#0		; PWM (for the main loop)
+	mov	@r0,a		; set it
+
+	mov	dptr,#IFCONFIG	; switch off GPIF
+	mov	a,#10100000b	; gpif, 30MHz, internal IFCLK
+	lcall	syncdelaywr
+	ret
+	
+
+;;; init PWM
+startPWM:
+	mov	dptr,#IFCONFIG	; switch on IFCLK signal
+	mov	a,#10100010b	; gpif, 30MHz, internal IFCLK
+	lcall	syncdelaywr
+
+	mov	OEB,0FFH	; output to port B
+
+	mov	DPTR,#EP4CFG
+	mov	a,#10100000b	; valid, out, bulk
+	movx	@DPTR,a
+
+	;; reset the endpoint
+	mov	dptr,#FIFORESET
+	mov	a,#80h		; NAK
+	lcall	syncdelaywr
+	mov	a,#84h		; reset EP4 + NAK
+	lcall	syncdelaywr
+	mov	a,#0		; normal op
+	lcall	syncdelaywr
+
+	mov	dptr,#EP4BCL
+	mov	a,#0H		; discard packets
+	lcall	syncdelaywr	; empty FIFO buffer
+	lcall	syncdelaywr	; empty FIFO buffer
+
+	;; aborts all transfers by the GPIF
+	mov	dptr,#GPIFABORT
+	mov	a,#0ffh		; abort all transfers
+	lcall	syncdelaywr
+
+	;; wait for GPIF to finish
+wait_f_abort:
+	mov	a,GPIFTRIG	; GPIF status
+	anl	a,#80h		; done bit
+	jz	wait_f_abort	; GPIF busy
+
+        mov     dptr,#GPIFCTLCFG
+        mov     a,#10000000b    ; tri state for CTRL
+        lcall   syncdelaywr
+
+        mov     dptr,#GPIFIDLECTL
+        mov     a,#11110000b    ; all CTL outputs low
+        lcall   syncdelaywr
+
+	;; abort if FIFO is empty
+        mov     a,#00000001b    ; abort if empty
+        mov     dptr,#EP4GPIFFLGSEL
+        lcall   syncdelaywr
+
+	;; 
+        mov     a,#00000001b    ; stop if GPIF flg
+        mov     dptr,#EP4GPIFPFSTOP
+        lcall   syncdelaywr
+
+	;; transaction counter
+	mov	a,#0ffH
+	mov	dptr,#GPIFTCB3
+	lcall	syncdelaywr
+
+	;; transaction counter
+	mov	a,#0ffH
+	mov	dptr,#GPIFTCB2
+	lcall	syncdelaywr
+
+	;; transaction counter
+	mov	a,#0ffH		; 512 bytes
+	mov	dptr,#GPIFTCB1
+	lcall	syncdelaywr
+
+	;; transaction counter
+	mov	a,#0ffH
+	mov	dptr,#GPIFTCB0
+	lcall	syncdelaywr
+
+	;; RDY pins. Not used here.
+        mov     a,#0
+        mov     dptr,#GPIFREADYCFG
+        lcall   syncdelaywr
+
+	;; drives the output in the IDLE state
+        mov     a,#1
+        mov     dptr,#GPIFIDLECS
+        lcall   syncdelaywr
+
+	;; direct data transfer from the EP to the GPIF
+	mov	dptr,#EP4FIFOCFG
+	mov	a,#00010000b	; autoout=1, byte-wide
+	lcall	syncdelaywr
+
+	;; waveform 0 is used for FIFO out
+	mov	dptr,#GPIFWFSELECT
+	mov	a,#00000000b
+	movx	@dptr,a
+	lcall	syncdelay
+
+	;; transfer the delay byte from the EP to the waveform
+	mov	dptr,#0e781h	; EP1 buffer
+	movx	a,@dptr		; get the delay
+	mov	dptr,#waveform	; points to the waveform
+	mov	r2,#6		; fill 6 bytes
+timloop:
+	movx	@dptr,a		; save timing in a xxx
+	inc	dptr
+	djnz	r2,timloop	; fill the 6 delay bytes
+
+	;; load waveform
+        mov     AUTOPTRH2,#0E4H ; XDATA0H
+        lcall   syncdelay
+        mov     AUTOPTRL2,#00H  ; XDATA0L
+        lcall   syncdelay
+
+	mov	dptr,#waveform	; points to the waveform
+	
+        mov     AUTOPTRSETUP,#7 ; autoinc and enable
+        lcall   syncdelay
+
+        mov     r2,#20H         ; 32 bytes to transfer
+
+wavetr:
+        movx    a,@dptr
+	inc	dptr
+	push	dpl
+	push	dph
+	push	dpl1
+	push	dph1
+        mov     dptr,#XAUTODAT2
+        movx    @dptr,a
+        lcall   syncdelay
+	pop	dph1 
+	pop	dpl1
+	pop	dph 
+	pop	dpl
+        djnz    r2,wavetr
+
+	mov	dptr,#OUTPKTEND
+	mov	a,#084H
+	lcall	syncdelaywr
+	lcall	syncdelaywr
+
+	mov	r0,#PWMFLAG	; flag for PWM
+	mov	a,#1		; PWM (for the main loop)
+	mov	@r0,a		; set it
+
+	ret
+
+	
+
+;; need to delay every time the byte counters
+;; for the EPs have been changed.
+
+syncdelay:
+	nop
+	nop
+	nop
+	nop
+	nop
+	nop
+	nop
+	nop
+	nop
+	ret
+
+syncdelaywr:
+	movx	@dptr,a
+	lcall	syncdelay
+	ret
+
+
+
+	.org	1F00h		; lookup table at the end of memory
+
+swap_lut:
+.db 0,128,64,192,32,160,96,224,16,144,80,208,48,176,112,240,8,136
+.db 72,200,40,168,104,232,24,152,88,216,56,184,120,248,4,132,68,196,36,164,100
+.db 228,20,148,84,212,52,180,116,244,12,140,76,204,44,172,108,236,28,156,92,220
+.db 60,188,124,252,2,130,66,194,34,162,98,226,18,146,82,210,50,178,114,242,10
+.db 138,74,202,42,170,106,234,26,154,90,218,58,186,122,250,6,134,70,198,38,166
+.db 102,230,22,150,86,214,54,182,118,246,14,142,78,206,46,174,110,238,30,158,94
+.db 222,62,190,126,254,1,129,65,193,33,161,97,225,17,145,81,209,49,177,113,241,9
+.db 137,73,201,41,169,105,233,25,153,89,217,57,185,121,249,5,133,69,197,37,165
+.db 101,229,21,149,85,213,53,181,117,245,13,141,77,205,45,173,109,237,29,157,93
+.db 221,61,189,125,253,3,131,67,195,35,163,99,227,19,147,83,211,51,179,115,243,11
+.db 139,75,203,43,171,107,235,27,155,91,219,59,187,123,251,7,135,71,199,39,167
+.db 103,231,23,151,87,215,55,183,119,247,15,143,79,207,47,175,111,239,31,159,95
+.db 223,63,191,127,255
+
+
+
+	
+.End
+
+
diff --git a/usbdux_firmware.bin b/usbdux_firmware.bin
new file mode 100644
index 0000000..7f537fc
--- /dev/null
+++ b/usbdux_firmware.bin
diff --git a/usbduxfast_firmware.bin b/usbduxfast_firmware.bin
new file mode 100644
index 0000000..3a6441d
--- /dev/null
+++ b/usbduxfast_firmware.bin
diff --git a/usbduxsigma_firmware.bin b/usbduxsigma_firmware.bin
new file mode 100644
index 0000000..b946264
--- /dev/null
+++ b/usbduxsigma_firmware.bin