Adding upstream version 3.2.3+dfsg.upstream/3.2.3+dfsg

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 1115 insertions, 0 deletions

diff --git a/raddb/mods-available/eap b/raddb/mods-available/eap
new file mode 100644
index 0000000..ee9e539
--- /dev/null
+++ b/raddb/mods-available/eap
@@ -0,0 +1,1115 @@
+# -*- text -*-
+##
+##  eap.conf -- Configuration for EAP types (PEAP, TTLS, etc.)
+##
+##	$Id$
+
+#######################################################################
+#
+#  Whatever you do, do NOT set 'Auth-Type := EAP'.  The server
+#  is smart enough to figure this out on its own.  The most
+#  common side effect of setting 'Auth-Type := EAP' is that the
+#  users then cannot use ANY other authentication method.
+#
+eap {
+	#  Invoke the default supported EAP type when
+	#  EAP-Identity response is received.
+	#
+	#  The incoming EAP messages DO NOT specify which EAP
+	#  type they will be using, so it MUST be set here.
+	#
+	#  For now, only one default EAP type may be used at a time.
+	#
+	#  If the EAP-Type attribute is set by another module,
+	#  then that EAP type takes precedence over the
+	#  default type configured here.
+	#
+	default_eap_type = md5
+
+	#  A list is maintained to correlate EAP-Response
+	#  packets with EAP-Request packets.  After a
+	#  configurable length of time, entries in the list
+	#  expire, and are deleted.
+	#
+	timer_expire = 60
+
+	#  There are many EAP types, but the server has support
+	#  for only a limited subset.  If the server receives
+	#  a request for an EAP type it does not support, then
+	#  it normally rejects the request.  By setting this
+	#  configuration to "yes", you can tell the server to
+	#  instead keep processing the request.  Another module
+	#  MUST then be configured to proxy the request to
+	#  another RADIUS server which supports that EAP type.
+	#
+	#  If another module is NOT configured to handle the
+	#  request, then the request will still end up being
+	#  rejected.
+	#
+	ignore_unknown_eap_types = no
+
+	# Cisco AP1230B firmware 12.2(13)JA1 has a bug.  When given
+	# a User-Name attribute in an Access-Accept, it copies one
+	# more byte than it should.
+	#
+	# We can work around it by configurably adding an extra
+	# zero byte.
+	#
+	cisco_accounting_username_bug = no
+
+	#  Help prevent DoS attacks by limiting the number of
+	#  sessions that the server is tracking.  For simplicity,
+	#  this is taken from the "max_requests" directive in
+	#  radiusd.conf.
+	#
+	max_sessions = ${max_requests}
+
+
+	############################################################
+	#
+	#  Supported EAP-types
+	#
+
+
+	#  EAP-MD5
+	#
+	#  We do NOT recommend using EAP-MD5 authentication
+	#  for wireless connections.  It is insecure, and does
+	#  not provide for dynamic WEP keys.
+	#
+	md5 {
+	}
+
+
+	#  EAP-pwd -- secure password-based authentication
+	#
+	#pwd {
+	#	group = 19
+
+	#	server_id = theserver@example.com
+
+		#  This has the same meaning as for TLS.
+		#
+	#	fragment_size = 1020
+
+		# The virtual server which determines the
+		# "known good" password for the user.
+		# Note that unlike TLS, only the "authorize"
+		# section is processed.  EAP-PWD requests can be
+		# distinguished by having a User-Name, but
+		# no User-Password, CHAP-Password, EAP-Message, etc.
+		#
+	#	virtual_server = "inner-tunnel"
+	#}
+
+
+	#  Cisco LEAP
+	#
+	#  We do not recommend using LEAP in new deployments.  See:
+	#  http://www.securiteam.com/tools/5TP012ACKE.html
+	#
+	#  LEAP is not supported.
+	#  It is insecure, and no one should be using it.
+	#
+
+
+	#  EAP-GTC -- Generic Token Card
+	#
+	#  Currently, this is only permitted inside of EAP-TTLS,
+	#  or EAP-PEAP.  The module "challenges" the user with
+	#  text, and the response from the user is taken to be
+	#  the User-Password.
+	#
+	#  Proxying the tunneled EAP-GTC session is a bad idea,
+	#  the users password will go over the wire in plain-text,
+	#  for anyone to see.
+	#
+	gtc {
+		#  The default challenge, which many clients
+		#  ignore..
+		#
+	#	challenge = "Password: "
+
+		#  The plain-text response which comes back
+		#  is put into a User-Password attribute,
+		#  and passed to another module for
+		#  authentication.  This allows the EAP-GTC
+		#  response to be checked against plain-text,
+		#  or crypt'd passwords.
+		#
+		#  If you say "Local" instead of "PAP", then
+		#  the module will look for a User-Password
+		#  configured for the request, and do the
+		#  authentication itself.
+		#
+		auth_type = PAP
+	}
+
+
+	#  Common TLS configuration for TLS-based EAP types
+	#  ------------------------------------------------
+	#
+	#  See raddb/certs/README.md for additional comments
+	#  on certificates.
+	#
+	#  If OpenSSL was not found at the time the server was
+	#  built, the "tls", "ttls", and "peap" sections will
+	#  be ignored.
+	#
+	#  If you do not currently have certificates signed by
+	#  a trusted CA you may use the 'snakeoil' certificates.
+	#  Included with the server in raddb/certs.
+	#
+	#  If these certificates have not been auto-generated:
+	#    cd raddb/certs
+	#    make
+	#
+	#  These test certificates SHOULD NOT be used in a normal
+	#  deployment.  They are created only to make it easier
+	#  to install the server, and to perform some simple
+	#  tests with EAP-TLS, TTLS, or PEAP.
+	#
+	#  Note that you should NOT use a globally known CA here!
+	#  e.g. using a Verisign cert as a "known CA" means that
+	#  ANYONE who has a certificate signed by them can
+	#  authenticate via EAP-TLS!  This is likely not what you want.
+	#
+	tls-config tls-common {
+		private_key_password = whatever
+		private_key_file = ${certdir}/server.pem
+
+		#  If Private key & Certificate are located in
+		#  the same file, then private_key_file &
+		#  certificate_file must contain the same file
+		#  name.
+		#
+		#  If ca_file (below) is not used, then the
+		#  certificate_file below SHOULD also include all of
+		#  the intermediate CA certificates used to sign the
+		#  server certificate, but NOT the root CA.
+		#
+		#  Including the ROOT CA certificate is not useful and
+		#  merely inflates the exchanged data volume during
+		#  the TLS negotiation.
+		#
+		#  This file should contain the server certificate,
+		#  followed by intermediate certificates, in order.
+		#  i.e. If we have a server certificate signed by CA1,
+		#  which is signed by CA2, which is signed by a root
+		#  CA, then the "certificate_file" should contain
+		#  server.pem, followed by CA1.pem, followed by
+		#  CA2.pem.
+		#
+		#  When using "ca_file" or "ca_path", the
+		#  "certificate_file" should contain only
+		#  "server.pem".  And then you may (or may not) need
+		#  to set "auto_chain", depending on your version of
+		#  OpenSSL.
+		#
+		#  In short, SSL / TLS certificates are complex.
+		#  There are many versions of software, each of which
+		#  behave slightly differently.  It is impossible to
+		#  give advice which will work everywhere.  Instead,
+		#  we give general guidelines.
+		#
+		certificate_file = ${certdir}/server.pem
+
+		#  Trusted Root CA list
+		#
+		#  This file can contain multiple CA certificates.
+		#  ALL of the CA's in this list will be trusted to
+		#  issue client certificates for authentication.
+		#
+		#  In general, you should use self-signed
+		#  certificates for 802.1x (EAP) authentication.
+		#  In that case, this CA file should contain
+		#  *one* CA certificate.
+		#
+		ca_file = ${cadir}/ca.pem
+
+		#
+		#  Directory where multiple CAs are stored.  Both
+		#  "ca_file" and "ca_path" can be used at the same time.
+		#
+		ca_path = ${cadir}
+
+		# OpenSSL does not reload contents of ca_path dir over time.
+		# That means that if check_crl is enabled and CRLs are loaded
+		# from ca_path dir, at some point CRLs will expire and
+		# the server will stop authenticating users.
+		#
+		# If ca_path_reload_interval is non-zero, it will force OpenSSL
+		# to reload all data from ca_path periodically
+		#
+		# Flush ca_path each hour
+	#	ca_path_reload_interval = 3600
+
+	 	#  OpenSSL will automatically create certificate chains,
+	 	#  unless we tell it to not do that.  The problem is that
+	 	#  it sometimes gets the chains right from a certificate
+	 	#  signature view, but wrong from the clients view.
+		#
+		#  When setting "auto_chain = no", the server certificate
+		#  file MUST include the full certificate chain.
+		#
+	#	auto_chain = yes
+
+		#  If OpenSSL supports TLS-PSK, then we can use a
+		#  fixed PSK identity and (hex) password.  These can
+		#  be used at the same time as the certificate
+		#  configuration, but only for TLS 1.0 through 1.2.
+		#
+		#  If PSK and certificates are configured at the same
+		#  time for TLS 1.3, then the server will warn you,
+		#  and will disable TLS 1.3, as it will not work.
+		#
+		#  The work around is to have two modules (or for
+		#  RadSec, two listen sections).  One will have PSK
+		#  configured, and the other will have certificates
+		#  configured.
+		#
+	#	psk_identity = "test"
+	#	psk_hexphrase = "036363823"
+
+		#  Dynamic queries for the PSK.  If TLS-PSK is used,
+		#  and psk_query is set, then you MUST NOT use
+		#  psk_identity or psk_hexphrase.
+		#
+		#  Instead, use a dynamic expansion similar to the one
+		#  below.  It keys off of TLS-PSK-Identity.  It should
+		#  return a of string no more than 512 hex characters.
+		#  That string will be converted to binary, and will
+		#  be used as the dynamic PSK hexphrase.
+		#
+		#  Note that this query is just an example.  You will
+		#  need to customize it for your installation.
+		#
+	#	psk_query = "%{sql:select hex(key) from psk_keys where keyid = '%{TLS-PSK-Identity}'}"
+
+		#  For DH cipher suites to work in OpenSSL < 1.1.0,
+		#  you have to run OpenSSL to create the DH file
+		#  first:
+		#
+		#    openssl dhparam -out certs/dh 2048
+		#
+		#  For OpenSSL >= 1.1.0, just leave this commented
+		#  out, and OpenSSL will do the right thing.
+		#
+	#	dh_file = ${certdir}/dh
+
+		#  If your system doesn't have /dev/urandom,
+		#  you will need to create this file, and
+		#  periodically change its contents.
+		#
+		#  For security reasons, FreeRADIUS doesn't
+		#  write to files in its configuration
+		#  directory.
+		#
+	#	random_file = /dev/urandom
+
+		#  This can never exceed the size of a RADIUS
+		#  packet (4096 bytes), and is preferably half
+		#  that, to accommodate other attributes in
+		#  RADIUS packet.  On most APs the MAX packet
+		#  length is configured between 1500 - 1600
+		#  In these cases, fragment size should be
+		#  1024 or less.
+		#
+	#	fragment_size = 1024
+
+		#  include_length is a flag which is
+		#  by default set to yes If set to
+		#  yes, Total Length of the message is
+		#  included in EVERY packet we send.
+		#  If set to no, Total Length of the
+		#  message is included ONLY in the
+		#  First packet of a fragment series.
+		#
+	#	include_length = yes
+
+
+		#  Check the Certificate Revocation List
+		#
+		#  1) Copy CA certificates and CRLs to same directory.
+		#  2) Execute 'c_rehash <CA certs&CRLs Directory>'.
+		#     'c_rehash' is OpenSSL's command.
+		#  3) uncomment the lines below.
+		#  5) Restart radiusd
+	#	check_crl = yes
+
+		# Check if intermediate CAs have been revoked.
+	#	check_all_crl = yes
+
+		# Accept an expired Certificate Revocation List
+		#
+	#	allow_expired_crl = no
+
+		#  If check_cert_issuer is set, the value will
+		#  be checked against the DN of the issuer in
+		#  the client certificate.  If the values do not
+		#  match, the certificate verification will fail,
+		#  rejecting the user.
+		#
+		#  This check can be done more generally by checking
+		#  the value of the TLS-Client-Cert-Issuer attribute.
+		#  This check can be done via any mechanism you
+		#  choose.
+		#
+	#	check_cert_issuer = "/C=GB/ST=Berkshire/L=Newbury/O=My Company Ltd"
+
+		#  If check_cert_cn is set, the value will
+		#  be xlat'ed and checked against the CN
+		#  in the client certificate.  If the values
+		#  do not match, the certificate verification
+		#  will fail rejecting the user.
+		#
+		#  This check is done only if the previous
+		#  "check_cert_issuer" is not set, or if
+		#  the check succeeds.
+		#
+		#  This check can be done more generally by writing
+		#  "unlang" statements to examine the value of the
+		#  TLS-Client-Cert-Common-Name attribute.
+		#
+	#	check_cert_cn = %{User-Name}
+
+		#
+		#  This configuration item only applies when there is
+		#  an intermediate CA between the "root" CA, and the
+		#  client certificate.  If we trust the root CA, then
+		#  by definition we also trust ANY intermediate CA
+		#  which is signed by that root.  This means ANOTHER
+		#  intermediate CA can issue client certificates, and
+		#  have them accepted by the EAP module.
+		#
+		#  The solution is to list ONLY the trusted CAs in the
+		#  FreeRADIUS configuration, and then set this
+		#  configuration item to "yes".
+		#
+		#  Then, when the server receives a client certificate
+		#  from an untrusted CA, that authentication request
+		#  can be rejected.
+		#
+		#  It is possible to do these checks in "unlang", by
+		#  checking for unknown names in the
+		#  TLS-Cert-Common-Name attribute, but that is
+		#  more complex.  So we add a configuration option
+		#  which can be set once, and which works for all
+		#  possible intermediate CAs, no matter what their
+		#  value.
+		#
+	#	reject_unknown_intermediate_ca = no
+
+		#  Set this option to specify the allowed
+		#  TLS cipher suites.  The format is listed
+		#  in "man 1 ciphers".
+		#
+		cipher_list = "DEFAULT"
+
+		#  Set this option to specify the allowed
+		#  TLS signature algorithms for OpenSSL 1.1.1 and above.
+		#  The format and available signature algorithms are listed
+		#  in "man 3 SSL_CTX_set1_sigalgs_list".
+		#
+		# sigalgs_list = ""
+
+		#  If enabled, OpenSSL will use server cipher list
+		#  (possibly defined by cipher_list option above)
+		#  for choosing right cipher suite rather than
+		#  using client-specified list which is OpenSSl default
+		#  behavior.  Setting this to "yes" means that OpenSSL
+		#  will choose the servers ciphers, even if they do not
+		#  best match what the client sends.
+		#
+		#  TLS negotiation is usually good, but can be imperfect.
+		#  This setting allows administrators to "fine tune" it
+		#  if necessary.
+		#
+		cipher_server_preference = no
+
+		#  You can selectively disable TLS versions for
+		#  compatability with old client devices.
+		#
+		#  If your system has OpenSSL 1.1.0 or greater, do NOT
+		#  use these.  Instead, set tls_min_version and
+		#  tls_max_version.
+		#
+#		disable_tlsv1_2 = yes
+#		disable_tlsv1_1 = yes
+#		disable_tlsv1 = yes
+
+
+		#  Set min / max TLS version.
+		#
+		#  Generally speaking you should NOT use TLS 1.0 or
+		#  TLS 1.1.  They are old, possibly insecure, and
+		#  deprecated.  However, it is sometimes necessary to
+		#  enable it for compatibility with legact systems.
+		#  We recommend replacing those legacy systems, and
+		#  using at least TLS 1.2.
+		#
+		#  Some Debian versions disable older versions of TLS,
+		#  and requires the application to manually enable
+		#  them.
+		#
+		#  If you are running such a distribution, you should
+		#  set these options, otherwise older clients will not
+		#  be able to connect.
+		#
+		#  Allowed values are "1.0", "1.1", "1.2", and "1.3".
+		#
+		#  As of 2021, it is STRONGLY RECOMMENDED to set
+		#
+		#	tls_min_version = "1.2"
+		#
+		#  Older TLS versions are insecure and deprecated.
+		#
+		#  In order to enable TLS 1.0 and TLS 1.1, you may
+		#  also need to update cipher_list below to:
+		#
+		#   * OpenSSL >= 3.x
+		#
+		#	cipher_list = "DEFAULT@SECLEVEL=0"
+		#
+		#   * OpenSSL < 3.x
+		#
+		#	cipher_list = "DEFAULT@SECLEVEL=1"
+		#
+		#  The values must be in quotes.
+		#
+		#  We also STRONGLY RECOMMEND to set
+		#
+		#	tls_max_version = "1.2"
+		#
+		#  While the server will accept "1.3" as a value,
+		#  most EAP supplicants WILL NOT DO TLS 1.3 PROPERLY.
+		#
+		#  i.e. they WILL NOT WORK, SO DO NOT ASK QUESTIONS ON
+		#  THE LIST ABOUT WHY IT DOES NOT WORK.
+		#
+		#  The TLS 1.3 support is here for future
+		#  compatibility, as clients get upgraded, and people
+		#  don't upgrade their copies of FreeRADIUS.
+		#
+		#  Also note that we only support TLS 1.3 for EAP-TLS,
+		#  TTLS, and PEAP.  It is not supported for EAP-FAST.
+		#
+		tls_min_version = "1.2"
+		tls_max_version = "1.2"
+
+		#  Elliptical cryptography configuration
+		#
+		#  This configuration should be one of the following:
+		#
+		#  * a name of the curve to use, e.g. "prime256v1".
+		#
+		#  * a colon separated list of curve NIDs or names.
+		#
+		#  * an empty string, in which case OpenSSL will choose
+		#    the "best" curve for the situation.
+		#
+		#  For supported curve names, please run
+		#
+		#	openssl ecparam -list_curves
+		#
+		ecdh_curve = ""
+
+		#  Session resumption / fast reauthentication
+		#  cache.
+		#
+		#  The cache contains the following information:
+		#
+		#   session Id - unique identifier, managed by SSL
+		#   User-Name  - from the Access-Accept
+		#   Stripped-User-Name - from the Access-Request
+		#   Cached-Session-Policy - from the Access-Accept
+		#
+		#  See also the "store" subsection below for
+		#  additional attributes which can be cached.
+		#
+		#  The "Cached-Session-Policy" is the name of a
+		#  policy which should be applied to the cached
+		#  session.  This policy can be used to assign
+		#  VLANs, IP addresses, etc.  It serves as a useful
+		#  way to re-apply the policy from the original
+		#  Access-Accept to the subsequent Access-Accept
+		#  for the cached session.
+		#
+		#  On session resumption, these attributes are
+		#  copied from the cache, and placed into the
+		#  reply list.
+		#
+		#  You probably also want "use_tunneled_reply = yes"
+		#  when using fast session resumption.
+		#
+		#  You can check if a session has been resumed by
+		#  looking for the existence of the EAP-Session-Resumed
+		#  attribute.  Note that this attribute will *only*
+		#  exist in the "post-auth" section.
+		#
+		#  CAVEATS: The cache is stored and reloaded BEFORE
+		#  the "post-auth" section is run.  This limitation
+		#  makes caching more difficult than it should be.  In
+		#  practice, it means that the first authentication
+		#  session must set the reply attributes before the
+		#  post-auth section is run.
+		#
+		#  When the session is resumed, the attributes are
+		#  restored and placed into the session-state list.
+		#
+		cache {
+			#  Enable it.  The default is "no". Deleting the entire "cache"
+			#  subsection also disables caching.
+			#
+			#  The session cache requires the use of the
+			#  "name" and "persist_dir" configuration
+			#  items, below.
+			#
+			#  The internal OpenSSL session cache has been permanently
+			#  disabled.
+			#
+			#  You can disallow resumption for a particular user by adding the
+			#  following attribute to the control item list:
+			#
+			#    Allow-Session-Resumption = No
+			#
+			#  If "enable = no" below, you CANNOT enable resumption for just one
+			#  user by setting the above attribute to "yes".
+			#
+			enable = no
+
+			#  Lifetime of the cached entries, in hours. The sessions will be
+			#  deleted/invalidated after this time.
+			#
+			lifetime = 24 # hours
+
+			#  Internal "name" of the session cache. Used to
+			#  distinguish which TLS context sessions belong to.
+			#
+			#  The server will generate a random value if unset.
+			#  This will change across server restart so you MUST
+			#  set the "name" if you want to persist sessions (see
+			#  below).
+			#
+		#	name = "EAP module"
+
+			#  Simple directory-based storage of sessions.
+			#  Two files per session will be written, the SSL
+			#  state and the cached VPs. This will persist session
+			#  across server restarts.
+			#
+			#  The default directory is ${logdir}, for historical
+			#  reasons.  You should ${db_dir} instead.  And check
+			#  the value of db_dir in the main radiusd.conf file.
+			#  It should not point to ${raddb}
+			#
+			#  The server will need write perms, and the directory
+			#  should be secured from anyone else. You might want
+			#  a script to remove old files from here periodically:
+			#
+			#    find ${logdir}/tlscache -mtime +2 -exec rm -f {} \;
+			#
+			#  This feature REQUIRES "name" option be set above.
+			#
+		#	persist_dir = "${logdir}/tlscache"
+
+			#
+			#  It is possible to partially
+			#  control which attributes exist in the
+			#  session cache.  This subsection lists
+			#  attributes which are taken from the reply,
+			#  and saved to the on-disk cache.  When the
+			#  session is resumed, these attributes are
+			#  added to the "session-state" list.  The
+			#  default configuration will then take care
+			#  of copying them to the reply.
+			#
+			store {
+				Tunnel-Private-Group-Id
+			}
+		}
+
+		#  Client certificates can be validated via an
+		#  external command.  This allows dynamic CRLs or OCSP
+		#  to be used.
+		#
+		#  This configuration is commented out in the
+		#  default configuration.  Uncomment it, and configure
+		#  the correct paths below to enable it.
+		#
+		#  If OCSP checking is enabled, and the OCSP checks fail,
+		#  the verify section is not run.
+		#
+		#  If OCSP checking is disabled, the verify section is
+		#  run on successful certificate validation.
+		#
+		verify {
+			#  If the OCSP checks succeed, the verify section
+			#  is run to allow additional checks.
+			#
+			#  If you want to skip verify on OCSP success,
+			#  uncomment this configuration item, and set it
+			#  to "yes".
+			#
+		#	skip_if_ocsp_ok = no
+
+			#  A temporary directory where the client
+			#  certificates are stored.  This directory
+			#  MUST be owned by the UID of the server,
+			#  and MUST not be accessible by any other
+			#  users.  When the server starts, it will do
+			#  "chmod go-rwx" on the directory, for
+			#  security reasons.  The directory MUST
+			#  exist when the server starts.
+			#
+			#  You should also delete all of the files
+			#  in the directory when the server starts.
+			#
+		#	tmpdir = /tmp/radiusd
+
+			#  The command used to verify the client cert.
+			#  We recommend using the OpenSSL command-line
+			#  tool.
+			#
+			#  The ${..ca_path} text is a reference to
+			#  the ca_path variable defined above.
+			#
+			#  The %{TLS-Client-Cert-Filename} is the name
+			#  of the temporary file containing the cert
+			#  in PEM format.  This file is automatically
+			#  deleted by the server when the command
+			#  returns.
+			#
+		#	client = "/path/to/openssl verify -CApath ${..ca_path} %{TLS-Client-Cert-Filename}"
+		}
+
+		#  OCSP Configuration
+		#
+		#  Certificates can be verified against an OCSP
+		#  Responder. This makes it possible to immediately
+		#  revoke certificates without the distribution of
+		#  new Certificate Revocation Lists (CRLs).
+		#
+		ocsp {
+			#  Enable it.  The default is "no".
+			#  Deleting the entire "ocsp" subsection
+			#  also disables ocsp checking
+			#
+			enable = no
+
+			#  The OCSP Responder URL can be automatically
+			#  extracted from the certificate in question.
+			#  To override the OCSP Responder URL set
+			#  "override_cert_url = yes".
+			#
+			override_cert_url = yes
+
+			#  If the OCSP Responder address is not extracted from
+			#  the certificate, the URL can be defined here.
+			#
+			url = "http://127.0.0.1/ocsp/"
+
+			# If the OCSP Responder can not cope with nonce
+			# in the request, then it can be disabled here.
+			#
+			# For security reasons, disabling this option
+			# is not recommended as nonce protects against
+			# replay attacks.
+			#
+			# Note that Microsoft AD Certificate Services OCSP
+			# Responder does not enable nonce by default. It is
+			# more secure to enable nonce on the responder than
+			# to disable it in the query here.
+			# See http://technet.microsoft.com/en-us/library/cc770413%28WS.10%29.aspx
+			#
+		#	use_nonce = yes
+
+			# Number of seconds before giving up waiting
+			# for OCSP response. 0 uses system default.
+			#
+		#	timeout = 0
+
+			# Normally an error in querying the OCSP
+			# responder (no response from server, server did
+			# not understand the request, etc) will result in
+			# a validation failure.
+			#
+			# To treat these errors as 'soft' failures and
+			# still accept the certificate, enable this
+			# option.
+			#
+			# Warning: this may enable clients with revoked
+			# certificates to connect if the OCSP responder
+			# is not available. Use with caution.
+			#
+		#	softfail = no
+		}
+
+		#
+		#  The server can present different certificates based
+		#  on the realm presented in EAP.  See
+		#  raddb/certs/realms/README.md for examples of how to
+		#  configure this.
+		#
+		#  Note that the default is to use the same set of
+		#  realm certificates for both EAP and RadSec!  If
+		#  this is not what you want, you should use different
+		#  subdirectories or each, e.g. ${certdir}/realms/radsec/,
+		#  and ${certdir}/realms/eap/
+		#
+	#	realm_dir = ${certdir}/realms/
+	}
+
+
+	#  EAP-TLS
+	#
+	#  The TLS configuration for TLS-based EAP types is held in
+	#  the "tls-config" section, above.
+	#
+	tls {
+		#  Point to the common TLS configuration
+		#
+		tls = tls-common
+
+		#  As part of checking a client certificate, the EAP-TLS
+		#  sets some attributes such as TLS-Client-Cert-Common-Name. This
+		#  virtual server has access to these attributes, and can
+		#  be used to accept or reject the request.
+		#
+	#	virtual_server = check-eap-tls
+
+		#  You can control whether or not EAP-TLS requires a
+		#  client certificate by setting
+		#
+		#	configurable_client_cert = yes
+		#
+		#  Once that setting has been changed, you can then set
+		#
+		#	EAP-TLS-Require-Client-Cert = No
+		#
+		#  in the control items for a request, and the EAP-TLS
+		#  module will not require a client certificate from
+		#  the supplicant.
+		#
+		#  WARNING: This configuration should only be used
+		#  when the users are placed into a "captive portal"
+		#  or "walled garden", where they have limited network
+		#  access.  Otherwise the configuraton will allow
+		#  anyone on the network, without authenticating them!
+		#
+#		configurable_client_cert = no
+	}
+
+
+	#  EAP-TTLS -- Tunneled TLS
+	#
+	#  The TTLS module implements the EAP-TTLS protocol,
+	#  which can be described as EAP inside of Diameter,
+	#  inside of TLS, inside of EAP, inside of RADIUS...
+	#
+	#  Surprisingly, it works quite well.
+	#
+	ttls {
+		#  Which tls-config section the TLS negotiation parameters
+		#  are in - see EAP-TLS above for an explanation.
+		#
+		#  In the case that an old configuration from FreeRADIUS
+		#  v2.x is being used, all the options of the tls-config
+		#  section may also appear instead in the 'tls' section
+		#  above. If that is done, the tls= option here (and in
+		#  tls above) MUST be commented out.
+		#
+		tls = tls-common
+
+		#  The tunneled EAP session needs a default EAP type
+		#  which is separate from the one for the non-tunneled
+		#  EAP module.  Inside of the TTLS tunnel, we recommend
+		#  using EAP-MD5.  If the request does not contain an
+		#  EAP conversation, then this configuration entry is
+		#  ignored.
+		#
+		default_eap_type = md5
+
+		#  The tunneled authentication request does not usually
+		#  contain useful attributes like 'Calling-Station-Id',
+		#  etc.  These attributes are outside of the tunnel,
+		#  and normally unavailable to the tunneled
+		#  authentication request.
+		#
+		#  By setting this configuration entry to 'yes',
+		#  any attribute which is NOT in the tunneled
+		#  authentication request, but which IS available
+		#  outside of the tunnel, is copied to the tunneled
+		#  request.
+		#
+		#  allowed values: {no, yes}
+		#
+		copy_request_to_tunnel = no
+
+		#  This configuration item is deprecated.  Instead,
+		#  you should use:
+		#
+		#    update outer.session-state {
+		#      ...
+		#    }
+		#
+		#  This will cache attributes for the final Access-Accept.
+		#
+		#  See "update outer.session-state" in the "post-auth"
+		#  sections of sites-available/default, and of
+		#  sites-available/inner-tunnel
+		#
+		#  The reply attributes sent to the NAS are usually
+		#  based on the name of the user 'outside' of the
+		#  tunnel (usually 'anonymous').  If you want to send
+		#  the reply attributes based on the user name inside
+		#  of the tunnel, then set this configuration entry to
+		#  'yes', and the reply to the NAS will be taken from
+		#  the reply to the tunneled request.
+		#
+		#  allowed values: {no, yes}
+		#
+		use_tunneled_reply = no
+
+		#  The inner tunneled request can be sent
+		#  through a virtual server constructed
+		#  specifically for this purpose.
+		#
+		#  A virtual server MUST be specified.
+		#
+		virtual_server = "inner-tunnel"
+
+		#  This has the same meaning, and overwrites, the
+		#  same field in the "tls" configuration, above.
+		#  The default value here is "yes".
+		#
+	#	include_length = yes
+
+		#  Unlike EAP-TLS, EAP-TTLS does not require a client
+		#  certificate. However, you can require one by setting the
+		#  following option. You can also override this option by
+		#  setting
+		#
+		#    EAP-TLS-Require-Client-Cert = Yes
+		#
+		#  in the control items for a request.
+		#
+		#  Note that the majority of supplicants do not support using a
+		#  client certificate with EAP-TTLS, so this option is unlikely
+		#  to be usable for most people.
+		#
+	#	require_client_cert = yes
+	}
+
+
+	#  EAP-PEAP
+	#
+
+	##################################################
+	#
+	#  !!!!! WARNINGS for Windows compatibility  !!!!!
+	#
+	##################################################
+	#
+	#  If you see the server send an Access-Challenge,
+	#  and the client never sends another Access-Request,
+	#  then
+	#
+	#		STOP!
+	#
+	#  The server certificate has to have special OID's
+	#  in it, or else the Microsoft clients will silently
+	#  fail.  See the "scripts/xpextensions" file for
+	#  details, and the following page:
+	#
+	#	https://support.microsoft.com/en-us/help/814394/
+	#
+	#  If is still doesn't work, and you're using Samba,
+	#  you may be encountering a Samba bug.  See:
+	#
+	#	https://bugzilla.samba.org/show_bug.cgi?id=6563
+	#
+	#  Note that we do not necessarily agree with their
+	#  explanation... but the fix does appear to work.
+	#
+	##################################################
+
+	#  The tunneled EAP session needs a default EAP type
+	#  which is separate from the one for the non-tunneled
+	#  EAP module.  Inside of the TLS/PEAP tunnel, we
+	#  recommend using EAP-MS-CHAPv2.
+	#
+	peap {
+		#  Which tls-config section the TLS negotiation parameters
+		#  are in - see EAP-TLS above for an explanation.
+		#
+		#  In the case that an old configuration from FreeRADIUS
+		#  v2.x is being used, all the options of the tls-config
+		#  section may also appear instead in the 'tls' section
+		#  above. If that is done, the tls= option here (and in
+		#  tls above) MUST be commented out.
+		#
+		tls = tls-common
+
+		#  The tunneled EAP session needs a default
+		#  EAP type which is separate from the one for
+		#  the non-tunneled EAP module.  Inside of the
+		#  PEAP tunnel, we recommend using MS-CHAPv2,
+		#  as that is the default type supported by
+		#  Windows clients.
+		#
+		default_eap_type = mschapv2
+
+		#  The PEAP module also has these configuration
+		#  items, which are the same as for TTLS.
+		#
+		copy_request_to_tunnel = no
+
+		#  This configuration item is deprecated.  Instead,
+		#  you should use:
+		#
+		#    update outer.session-state {
+		#      ...
+		#    }
+		#
+		#  This will cache attributes for the final Access-Accept.
+		#
+		#  See "update outer.session-state" in the "post-auth"
+		#  sections of sites-available/default, and of
+		#  sites-available/inner-tunnel
+		#
+		use_tunneled_reply = no
+
+		#  When the tunneled session is proxied, the
+		#  home server may not understand EAP-MSCHAP-V2.
+		#  Set this entry to "no" to proxy the tunneled
+		#  EAP-MSCHAP-V2 as normal MSCHAPv2.
+		#
+		#  This setting can be over-ridden on a packet by
+		#  packet basis by setting
+		#
+		#	&control:Proxy-Tunneled-Request-As-EAP = yes
+		#
+	#	proxy_tunneled_request_as_eap = yes
+
+		#  The inner tunneled request can be sent
+		#  through a virtual server constructed
+		#  specifically for this purpose.
+		#
+		#  A virtual server MUST be specified.
+		#
+		virtual_server = "inner-tunnel"
+
+		#  This option enables support for MS-SoH
+		#  see doc/SoH.txt for more info.
+		#  It is disabled by default.
+		#
+	#	soh = yes
+
+		#  The SoH reply will be turned into a request which
+		#  can be sent to a specific virtual server:
+		#
+	#	soh_virtual_server = "soh-server"
+
+		#  Unlike EAP-TLS, PEAP does not require a client certificate.
+		#  However, you can require one by setting the following
+		#  option. You can also override this option by setting
+		#
+		#    EAP-TLS-Require-Client-Cert = Yes
+		#
+		#  in the control items for a request.
+		#
+		#  Note that the majority of supplicants do not support using a
+		#  client certificate with PEAP, so this option is unlikely to
+		#  be usable for most people.
+		#
+	#	require_client_cert = yes
+	}
+
+
+	#  EAP-MSCHAPv2
+	#
+	#  Note that it is the EAP MS-CHAPv2 sub-module, not
+	#  the main 'mschap' module.
+	#
+	#  Note also that in order for this sub-module to work,
+	#  the main 'mschap' module MUST ALSO be configured.
+	#
+	#  This module is the *Microsoft* implementation of MS-CHAPv2
+	#  in EAP.  There is another (incompatible) implementation
+	#  of MS-CHAPv2 in EAP by Cisco, which FreeRADIUS does not
+	#  currently support.
+	#
+	mschapv2 {
+		#  In earlier versions of the server, this module
+		#  never sent the MS-CHAP-Error message to the client.
+		#  This worked, but it had issues when the cached
+		#  password was wrong.  The server *should* send
+		#  "E=691 R=0" to the client, which tells it to prompt
+		#  the user for a new password.
+		#
+		#  The default is to use that functionality.  which is
+		#  known to work.  If you set "send_error = yes", then
+		#  the error message will be sent back to the client.
+		#  This *may* help some clients work better, but *may*
+		#  also cause other clients to stop working.
+		#
+	#	send_error = no
+
+		#  Server identifier to send back in the challenge.
+		#  This should generally be the host name of the
+		#  RADIUS server.  Or, some information to uniquely
+		#  identify it.
+		#
+	#	identity = "FreeRADIUS"
+	}
+
+
+	#  EAP-FAST
+	#
+	#  The FAST module implements the EAP-FAST protocol
+	#
+	#fast {
+		#  Point to the common TLS configuration
+		#
+	#	tls = tls-common
+
+		#  If 'cipher_list' is set here, it will over-ride the
+		#  'cipher_list' configuration from the 'tls-common'
+		#  configuration.  The EAP-FAST module has it's own
+		#  over-ride for 'cipher_list' because the
+		#  specifications mandata a different set of ciphers
+		#  than are used by the other EAP methods.
+		#
+		#  cipher_list though must include "ADH" for anonymous provisioning.
+		#  This is not as straight forward as appending "ADH" alongside
+		#  "DEFAULT" as "DEFAULT" contains "!aNULL" so instead it is
+		#  recommended "ALL:!EXPORT:!eNULL:!SSLv2" is used
+		#
+	#	cipher_list = "ALL:!EXPORT:!eNULL:!SSLv2"
+
+		#  PAC lifetime in seconds (default: seven days)
+		#
+	#	pac_lifetime = 604800
+
+		#  Authority ID of the server
+		#
+		#  If you are running a cluster of RADIUS servers, you should make
+		#  the value chosen here (and for "pac_opaque_key") the same on all
+		#  your RADIUS servers.  This value should be unique to your
+		#  installation.  We suggest using a domain name.
+		#
+	#	authority_identity = "1234"
+
+		#  PAC Opaque encryption key (must be exactly 32 bytes in size)
+		#
+		#  This value MUST be secret, and MUST be generated using
+		#  a secure method, such as via 'openssl rand -hex 32'
+		#
+	#	pac_opaque_key = "0123456789abcdef0123456789ABCDEF"
+
+		#  Same as for TTLS, PEAP, etc.
+		#
+	#	virtual_server = inner-tunnel
+	#}
+}