diff options
Diffstat (limited to '')
| -rw-r--r-- | raddb/clients.conf | 288 |
1 files changed, 288 insertions, 0 deletions
diff --git a/raddb/clients.conf b/raddb/clients.conf new file mode 100644 index 0000000..60f9f4b --- /dev/null +++ b/raddb/clients.conf @@ -0,0 +1,288 @@ +# -*- text -*- +## +## clients.conf -- client configuration directives +## +## $Id$ + +####################################################################### +# +# Define RADIUS clients (usually a NAS, Access Point, etc.). + +# +# Defines a RADIUS client. +# +# '127.0.0.1' is another name for 'localhost'. It is enabled by default, +# to allow testing of the server after an initial installation. If you +# are not going to be permitting RADIUS queries from localhost, we suggest +# that you delete, or comment out, this entry. +# +# + +# +# Each client has a "short name" that is used to distinguish it from +# other clients. +# +# In version 1.x, the string after the word "client" was the IP +# address of the client. In 2.0, the IP address is configured via +# the "ipaddr" or "ipv6addr" fields. For compatibility, the 1.x +# format is still accepted. +# +client localhost { + # Only *one* of ipaddr, ipv4addr, ipv6addr may be specified for + # a client. + # + # ipaddr will accept IPv4 or IPv6 addresses with optional CIDR + # notation '/<mask>' to specify ranges. + # + # ipaddr will accept domain names e.g. example.org resolving + # them via DNS. + # + # If both A and AAAA records are found, A records will be + # used in preference to AAAA. + ipaddr = 127.0.0.1 + + # Same as ipaddr but allows v4 addresses only. Requires A + # record for domain names. +# ipv4addr = * # any. 127.0.0.1 == localhost + + # Same as ipaddr but allows v6 addresses only. Requires AAAA + # record for domain names. +# ipv6addr = :: # any. ::1 == localhost + + # + # A note on DNS: We STRONGLY recommend using IP addresses + # rather than host names. Using host names means that the + # server will do DNS lookups when it starts, making it + # dependent on DNS. i.e. If anything goes wrong with DNS, + # the server won't start! + # + # The server also looks up the IP address from DNS once, and + # only once, when it starts. If the DNS record is later + # updated, the server WILL NOT see that update. + # + + # + # The transport protocol. + # + # If unspecified, defaults to "udp", which is the traditional + # RADIUS transport. It may also be "tcp", in which case the + # server will accept connections from this client ONLY over TCP. + # + proto = * + + # + # The shared secret use to "encrypt" and "sign" packets between + # the NAS and FreeRADIUS. You MUST change this secret from the + # default, otherwise it's not a secret any more! + # + # The secret can be any string, up to 8k characters in length. + # + # Control codes can be entered vi octal encoding, + # e.g. "\101\102" == "AB" + # Quotation marks can be entered by escaping them, + # e.g. "foo\"bar" + # + # A note on security: The security of the RADIUS protocol + # depends COMPLETELY on this secret! We recommend using a + # shared secret that is composed of: + # + # upper case letters + # lower case letters + # numbers + # + # And is at LEAST 8 characters long, preferably 16 characters in + # length. The secret MUST be random, and should not be words, + # phrase, or anything else that is recognisable. + # + # The default secret below is only for testing, and should + # not be used in any real environment. + # + secret = testing123 + + # + # Old-style clients do not send a Message-Authenticator + # in an Access-Request. RFC 5080 suggests that all clients + # SHOULD include it in an Access-Request. The configuration + # item below allows the server to require it. If a client + # is required to include a Message-Authenticator and it does + # not, then the packet will be silently discarded. + # + # allowed values: yes, no + require_message_authenticator = no + + # + # The short name is used as an alias for the fully qualified + # domain name, or the IP address. + # + # It is accepted for compatibility with 1.x, but it is no + # longer necessary in >= 2.0 + # +# shortname = localhost + + # + # the following three fields are optional, but may be used by + # checkrad.pl for simultaneous use checks + # + + # + # The nas_type tells 'checkrad.pl' which NAS-specific method to + # use to query the NAS for simultaneous use. + # + # Permitted NAS types are: + # + # cisco + # computone + # livingston + # juniper + # max40xx + # multitech + # netserver + # pathras + # patton + # portslave + # tc + # usrhiper + # other # for all other types + + # + nas_type = other # localhost isn't usually a NAS... + + # + # The following two configurations are for future use. + # The 'naspasswd' file is currently used to store the NAS + # login name and password, which is used by checkrad.pl + # when querying the NAS for simultaneous use. + # +# login = !root +# password = someadminpas + + # + # As of 2.0, clients can also be tied to a virtual server. + # This is done by setting the "virtual_server" configuration + # item, as in the example below. + # +# virtual_server = home1 + + # + # A pointer to the "home_server_pool" OR a "home_server" + # section that contains the CoA configuration for this + # client. For an example of a coa home server or pool, + # see raddb/sites-available/originate-coa +# coa_server = coa + + # + # Response window for proxied packets. If non-zero, + # then the lower of (home, client) response_window + # will be used. + # + # i.e. it can be used to lower the response_window + # packets from one client to a home server. It cannot + # be used to raise the response_window. + # +# response_window = 10.0 + + # + # Connection limiting for clients using "proto = tcp". + # + # This section is ignored for clients sending UDP traffic + # + limit { + # + # Limit the number of simultaneous TCP connections from a client + # + # The default is 16. + # Setting this to 0 means "no limit" + max_connections = 16 + + # The per-socket "max_requests" option does not exist. + + # + # The lifetime, in seconds, of a TCP connection. After + # this lifetime, the connection will be closed. + # + # Setting this to 0 means "forever". + lifetime = 0 + + # + # The idle timeout, in seconds, of a TCP connection. + # If no packets have been received over the connection for + # this time, the connection will be closed. + # + # Setting this to 0 means "no timeout". + # + # We STRONGLY RECOMMEND that you set an idle timeout. + # + idle_timeout = 30 + } +} + +# IPv6 Client +client localhost_ipv6 { + ipv6addr = ::1 + secret = testing123 +} + +# All IPv6 Site-local clients +#client sitelocal_ipv6 { +# ipv6addr = fe80::/16 +# secret = testing123 +#} + +#client example.org { +# ipaddr = radius.example.org +# secret = testing123 +#} + +# +# You can now specify one secret for a network of clients. +# When a client request comes in, the BEST match is chosen. +# i.e. The entry from the smallest possible network. +# +#client private-network-1 { +# ipaddr = 192.0.2.0/24 +# secret = testing123-1 +#} + +#client private-network-2 { +# ipaddr = 198.51.100.0/24 +# secret = testing123-2 +#} + +####################################################################### +# +# Per-socket client lists. The configuration entries are exactly +# the same as above, but they are nested inside of a section. +# +# You can have as many per-socket client lists as you have "listen" +# sections, or you can re-use a list among multiple "listen" sections. +# +# Un-comment this section, and edit a "listen" section to add: +# "clients = per_socket_clients". That IP address/port combination +# will then accept ONLY the clients listed in this section. +# +# There are additional considerations when using clients from SQL. +# +# A client can be link to a virtual server via modules such as SQL. +# This link is done via the following process: +# +# If there is no listener in a virtual server, SQL clients are added +# to the global list for that virtual server. +# +# If there is a listener, and the first listener does not have a +# "clients=..." configuration item, SQL clients are added to the +# global list. +# +# If there is a listener, and the first one does have a "clients=..." +# configuration item, SQL clients are added to that list. The client +# { ...} ` configured in that list are also added for that listener. +# +# The only issue is if you have multiple listeners in a virtual +# server, each with a different client list, then the SQL clients are +# added only to the first listener. +# +#clients per_socket_clients { +# client socket_client { +# ipaddr = 192.0.2.4 +# secret = testing123 +# } +#} |