#
#  The following policies are for the Chargeable-User-Identity
#  (CUI) configuration.
#
#  The policies below can be called as just 'cui' (not
#  cui.authorize etc..)  from the various config sections.
#

#
#  cui_hash_key definition
#  This key serves the purpose of protecting CUI values against
#  dictionary attacks, therefore should be chosen as a "random"
#  string and kept secret.
#
cui_hash_key = "changeme"

#
# cui_require_operator_name switch
# If this is set to nonzero value then CUI will only be added
# when a non-empty Operator-Name value is present in the request
#
cui_require_operator_name = "no"

#
#  The client indicates it can do CUI by sending a CUI attribute
#  containing one zero byte.
#  A non-empty value in Operator-Name can be an additional requirement.
#  Normally CUI support is turned on only for such requests.
#  CUI support can be used for local clients which do not
#  supports CUI themselves, the server can simulate a CUI request
#  adding the missing NUL CUI value and the Operator-Name attribute.
#  Clients which are supposed to get this treatment should
#  be marked by add_cui flag in clients.conf
#  We assume that local clients are marked in the client.conf with
#  add_cui flag, e.g.
#  client xxxx {
#    ...
#    add_cui = yes
#  }
#
cui.authorize {
	if ("%{client:add_cui}" == 'yes') {
		update request {
			&Chargeable-User-Identity := 0x00
		}
	}
}

#
#  Before proxing an Access-Request to a remote server, a NUL CUI
#  attribute should be added, unless it is already present in the request.
#
cui.pre-proxy {
	if (("%{request:Packet-Type}" == 'Access-Request') && ("%{client:add_cui}" == 'yes')) {
		update proxy-request {
			&Chargeable-User-Identity = 0x00
		}
	}
}


#
#  Add a CUI attribute based on the User-Name, and a secret key
#  known only to this server.
#  For EAP-TTLS and EAP-PEAP methods
#  use_tunneled_reply parameter MUST be set to yes
#
cui.post-auth {
	if (!&control:Proxy-To-Realm && &Chargeable-User-Identity && !&reply:Chargeable-User-Identity && \
	    (&Operator-Name || ('${policy.cui_require_operator_name}' != 'yes')) ) {
		update reply {
			&Chargeable-User-Identity = "%{sha1:${policy.cui_hash_key}%{tolower:%{User-Name}%{%{Operator-Name}:-}}}"
		}
	}

	#
	#  The section below will store a CUI for the User in the DB and remove the
	#  User-Name attribute from the reply if a CUI is present.
	#
	#  You need to configure the cuisql module and your database for this to work.
	#  If your NAS can do CUI based accounting themselves or you do not care about
	#  accounting, comment out the 'cuisql' line below.
	#
	if (&reply:Chargeable-User-Identity) {
		# Force User-Name to be the User-Name from the request
		update {
			&reply:User-Name := &request:User-Name
		}
		cuisql
	}
}


cui-inner.post-auth {
	if (&outer.request:Chargeable-User-Identity && \
	    (&outer.request:Operator-Name || ('${policy.cui_require_operator_name}' != 'yes'))) {
		update reply {
			&Chargeable-User-Identity := "%{sha1:${policy.cui_hash_key}%{tolower:%{User-Name}%{%{outer.request:Operator-Name}:-}}}"
		}
	}
}

#
#  If your NAS can do CUI based accounting or you do not care about
#  accounting then just comment out the call to cui in ......
#
#  If we had stored a CUI for the User, add it to the request.
#
cui.accounting {
	#
	#  If the CUI isn't in the packet, see if we can find it
	#  in the DB.
	#
	if (!&Chargeable-User-Identity) {
		update request {
			&Chargeable-User-Identity := "%{cuisql:\
				SELECT cui FROM cui \
				WHERE clientipaddress = '%{%{Packet-Src-IPv6-Address}:-%{Packet-Src-IP-Address}}' \
				AND callingstationid = '%{Calling-Station-Id}' \
				AND username = '%{User-Name}'}"
		}
	}

	#
	#  If it exists now, then write out when we last saw
	#  this CUI.
	#
	if (&Chargeable-User-Identity && (&Chargeable-User-Identity != '')) {
		cuisql
	}
}