1. Virtual Servers. FreeRADIUS supports virtual servers. The virtual servers do NOT have to be set up with the "sites-available" and "sites-enabled" directories. You can still have one "radiusd.conf" file, and put the server configuration there: ... server { authorize { ... } authenticate { ... } ... } ... The power of virtual servers lies in their ability to separate policies. A policy can be placed into a virtual server, where it is guaranteed to affect only the requests that are passed through that virtual server. In 1.x, the policies were global, and it sometimes took much effort to write a policy so that it only applied in certain limited situations. 2. What do we mean by "virtual server"? A virtual server is a (nearly complete) RADIUS server, just like a configuration for FreeRADIUS 1.x. However, FreeRADIUS can now run multiple virtual servers at the same time. The virtual servers can even proxy requests to each other! The simplest way to create a virtual server is to take the all of the request processing sections from radius.conf, ("authorize" , "authenticate", etc.) and wrap them in a "server {}" block, as above. You can create another virtual server by: 1) defining a new "server foo {...}" section in radiusd.conf 2) Putting the normal "authorize", etc. sections inside of it 3) Adding a "listen" section *inside* of the "server" section. e.g. ... server foo { listen { ipaddr = 127.0.0.1 port = 2000 type = auth } authorize { update control { Cleartext-Password := "bob" } pap } authenticate { pap } } ... With that text added to "radiusd.conf", run the server in debugging mode (radiusd -X), and in another terminal window, type: $ radtest bob bob localhost:2000 0 testing123 You should see the server return an Access-Accept. 3. Capabilities and limitations The only sub-sections that can appear in a virtual server section are: listen client authorize authenticate post-auth pre-proxy post-proxy preacct accounting session All other configuration parameters (modules, etc.) are global. Inside of a virtual server, the authorize, etc. sections have their normal meaning, and can contain anything that an authorize section could contain in 1.x. When a "listen" section is inside of a virtual server definition, it means that all requests sent to that IP/port will be processed through the virtual server. There cannot be two "listen" sections with the same IP address and port number. When a "client" section is inside of a virtual server definition, it means that that client is known only to the "listen" sections that are also inside of that virtual server. Not only is this client definition available only to this virtual server, but the details of the client configuration is also available only to this virtual server. i.e. Two virtual servers can listen on different IP address and ports, but both can have a client with IP address 127.0.0.1. The shared secret for that client can be different for each virtual server. 4. More complex "listen" capabilities The "listen" sections have a few additional configuration items that were not in 1.x, and were not mentioned above. These configuration items enable almost any mapping of IP / port to clients to virtual servers. The configuration items are: virtual_server = If set, all requests sent to this IP / port are processed through the named virtual server. This directive can be used only for "listen" sections that are global. i.e. It CANNOT be used if the "listen" section is inside of a virtual server. clients = If set, the "listen" section looks for a "clients" section: clients { ... } It looks inside of that named "clients" section for "client" subsections, at least one of which must exist. Each client in that section is added to the list of known clients for this IP / port. No other clients are known. If it is set, it over-rides the list of clients (if any) in the same virtual server. Note that the clients are NOT additive! If it is not set, then the clients from the current virtual server (if any) are used. If there are no clients in this virtual server, then the global clients are used. i.e. The most specific directive is used: * configuration in this "listen" section * clients in the same virtual server * global clients The directives are also *exclusive*, not *additive*. If you have one client in a virtual server, and another client referenced from a "listen" section, then that "listen" section will ONLY use the second client. It will NOT use both clients. 5. More complex "client" capabilities The "client" sections have a few additional configuration items that were not in 1.x, and were not mentioned above. These configuration items enable almost any mapping of IP / port to clients to virtual servers. The configuration items are: virtual_server = If set, all requests from this client are processed through the named virtual server. This directive can be used only for "client" sections that are global. i.e. It CANNOT be used if the "client" section is inside of a virtual server. If the "listen" section has a "server" entry, and a matching client is found ALSO with a "server" entry, then the clients server is used for that request. 6. Worked examples Listening on one socket, and mapping requests from two clients to two different servers. listen { ... } client one { ... virtual_server = server_one } client two { ... virtual_server = server_two } server server_one { authorize { ... } ... } server server_two { authorize { ... } ... } This could also be done as: listen { ... virtual_server = server_one } client one { ... } client two { ... virtual_server = server_two } server server_one { authorize { ... } ... } server server_two { authorize { ... } ... } In this case, the default server for the socket is "server_one", so there is no need to set that in the client "one" configuration. The "server_two" configuration for client "two" over-rides the default setting for the socket. Note that the following configuration will NOT work: listen { ... virtual_server = server_one } client one { ... } server server_one { authorize { ... } ... } server server_two { client two { ... } authorize { ... } ... } In this example, client "two" is hidden inside of the virtual server, where the "listen" section cannot find it. 7. Outlined examples This section outlines a number of examples, with alternatives. One server, multiple sockets - multiple "listen" sections in a "server" section one server per client - define multiple servers - have a global "listen" section - have multiple global "clients", each with "virtual_server = X" two servers, each with their own sockets - define multiple servers - put "client" sections into each "server" - put a "listen" section into each "server" Each server can list the same client IP, and the secret can be different two sockets, sharing a list of clients, but pointing to different servers - define global "listen" sections - in each, set "virtual_server = X" - in each, set "clients = Y" - define "clients Y" section, containing multiple clients. This also means that you can have a third socket, which doesn't share any of these clients. 8. How to decide what to do If you want *completely* separate policies for a socket or a client, then create a separate virtual server. Then, map the request to that server by setting configuration entries in a "listen" section or in a "client" section. Start off with the common cases first. If most of the clients and/or sockets get a particular policy, make that policy the default. Configure it without paying attention to the sockets or clients you want to add later, and without adding a second virtual server. Once it works, then add the second virtual server. If you want to re-use the previously defined sockets with the second virtual server, then you will need one or more global "client" sections. Those clients will contain a "virtual_server = ..." entry that will direct requests from those clients to the appropriate virtual server.