#
#	This file represents a server that is implementing an identity
#	provider for GSS-EAP (RFC 7055) using the trust router
#	protocol for dynamic realm discovery.  Any ABFAB identity
#	provider is also an ABFAB relying party proxy.
#
#	This file does not include a TLS listener; see abfab-tls for a simple
#	example of a RADSEC listener for ABFAB.
#
#	$Id$
#

server abfab-idp {
authorize {
	psk_authorize
	abfab_client_check
	filter_username
	preprocess

	#  If you intend to use CUI and you require that the Operator-Name
	#  be set for CUI generation and you want to generate CUI also
	#  for your local clients then uncomment the operator-name
	#  below and set the operator-name for your clients in clients.conf
#	operator-name

	#
	#  If you want to generate CUI for some clients that do not
	#  send proper CUI requests, then uncomment the
	#  cui below and set "add_cui = yes" for these clients in clients.conf
#	cui

	#
	# Do RFC 7542 bang path routing. If you want to only do standard
	# RADIUS NAI routing, comment out the below line.
	rfc7542

	#  Standard RADIUS NAI routing
	if (!updated) {
		suffix {
			updated = 1
			noop = reject
		}
	}

	eap {
		ok = return
	}

	expiration
	logintime
}

authenticate {
	#
	#  Allow EAP authentication.
	eap
}

#  Post-Authentication
#  Once we KNOW that the user has been authenticated, there are
#  additional steps we can take.
post-auth {
	#
	#  For EAP-TTLS and PEAP, add the cached attributes to the reply.
	#  The "session-state" attributes are automatically cached when
	#  an Access-Challenge is sent, and automatically retrieved
	#  when an Access-Request is received.
	#
	#  The session-state attributes are automatically deleted after
	#  an Access-Reject or Access-Accept is sent.
	#
	#  If both session-state and reply contain a User-Name attribute, remove
	#  the one in the reply if it is just a copy of the one in the request, so
	#  we don't end up with two User-Name attributes.

	if (session-state:User-Name && reply:User-Name && request:User-Name && (reply:User-Name == request:User-Name)) {
		update reply {
			&User-Name !* ANY
		}
	}
	update {
		&reply: += &session-state:
	}

	#  Create the CUI value and add the attribute to Access-Accept.
	#  Uncomment the line below if *returning* the CUI.
#	cui

	#
	#  If you want to have a log of authentication replies,
	#  un-comment the following line, and enable the
	#  'detail reply_log' module.
#	reply_log

	#
	#  After authenticating the user, do another SQL query.
	#
	#  See "Authentication Logging Queries" in `mods-config/sql/main/$driver/queries.conf`
	-sql

	#
	#  Un-comment the following if you want to modify the user's object
	#  in LDAP after a successful login.
	#
#	ldap

	# For Exec-Program and Exec-Program-Wait
	exec
	#  Remove reply message if the response contains an EAP-Message
	remove_reply_message_if_eap
	#  Access-Reject packets are sent through the REJECT sub-section of the
	#  post-auth section.
	#
	#  Add the ldap module name (or instance) if you have set
	#  'edir = yes' in the ldap module configuration
	#
	Post-Auth-Type REJECT {
		# log failed authentications in SQL, too.
		-sql
		attr_filter.access_reject

		# Insert EAP-Failure message if the request was
		# rejected by policy instead of because of an
		# authentication failure And already has an EAP message
		# For non-ABFAB, we insert the failure all the time, but for ABFAB
		# It's more desirable to preserve reply-message when we can
		if (&reply:Eap-Message) {
			eap
		}

		#  Remove reply message if the response contains an EAP-Message
		remove_reply_message_if_eap
	}
}
#
#  When the server decides to proxy a request to a home server,
#  the proxied request is first passed through the pre-proxy
#  stage.  This stage can re-write the request, or decide to
#  cancel the proxy.
#
#  Only a few modules currently have this method.
#
pre-proxy {
	# Before proxing the request add an Operator-Name attribute identifying
	# if the operator-name is found for this client.
	# No need to uncomment this if you have already enabled this in
	# the authorize section.
#	operator-name

	#  The client requests the CUI by sending a CUI attribute
	#  containing one zero byte.
	#  Uncomment the line below if *requesting* the CUI.
#	cui

	#  Uncomment the following line if you want to change attributes
	#  as defined in the preproxy_users file.
#	files

	#  Uncomment the following line if you want to filter requests
	#  sent to remote servers based on the rules defined in the
	#  'attrs.pre-proxy' file.
#	attr_filter.pre-proxy

	#  If you want to have a log of packets proxied to a home
	#  server, un-comment the following line, and the
	#  'detail pre_proxy_log' section, above.
#	pre_proxy_log
}
#
#  When the server receives a reply to a request it proxied
#  to a home server, the request may be massaged here, in the
#  post-proxy stage.
#
post-proxy {

	#  If you want to have a log of replies from a home server,
	#  un-comment the following line, and the 'detail post_proxy_log'
	#  section, above.
#	post_proxy_log

	#  Uncomment the following line if you want to filter replies from
	#  remote proxies based on the rules defined in the 'attrs' file.
#	attr_filter.post-proxy

	#
	#  If you are proxying LEAP, you MUST configure the EAP
	#  module, and you MUST list it here, in the post-proxy
	#  stage.
	#
	#  You MUST also use the 'nostrip' option in the 'realm'
	#  configuration.  Otherwise, the User-Name attribute
	#  in the proxied request will not match the user name
	#  hidden inside of the EAP packet, and the end server will
	#  reject the EAP request.
	#
	eap
}
}