Adding upstream version 9.1.upstream/9.1

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 102 insertions, 0 deletions

diff --git a/ospf6d/README b/ospf6d/README
new file mode 100644
index 0000000..f5a0046
--- /dev/null
+++ b/ospf6d/README
@@ -0,0 +1,102 @@
+
+		  Zebra OSPF daemon for IPv6 network
+
+			     2003/08/18
+
+README for newer code is not yet. General usage should remain
+the same. For further usage, see command helps by typing '?'
+in vty, and then imagin ! ;p) Previous README contents follows.
+
+		  Zebra OSPF daemon for IPv6 network
+
+			     2001/12/20
+
+Zebra OSPF6d is OSPF version 3 daemon which is specified by
+"OSPF for IPv6" (RFC 2740).
+
+*** NOTE ***
+  Zebra ospf6d is in development yet. It may lack some functionalities,
+  and may have some bugs. Use the latest version from the anoncvs
+  repository (http://www.zebra.org/cvs.html) !
+
+This file README is like memo yet, so please feel free to ask
+<yasu@sfc.wide.ad.jp> by E-mail. Patches will be appriciated.
+
+ospf6d's vty port was default to 2606/tcp.
+Use commands below.
+
+VIEW NODE:
+  show ipv6 ospf6
+    To see Router-ID, uptime of ospf6d, some statistics.
+
+  show ipv6 ospf6 database ...
+    This command shows LSA database. You can specify
+    LS-type/LS-ID/Advertising-Router of LSAs. '*' is recognized.
+
+  show ipv6 ospf6 interface ...
+    To see the status of the OSPF interface, and the configuration
+    like interface costs.
+
+  show ipv6 ospf6 neighbor ...
+    Shows state of neighbors and choosed (Backup) DR on the I/F.
+
+  show ipv6 ospf6 route (X::X)
+    This command shows internal routing table of the ospf6d.
+    Routes not calculated by OSPFv3 (like connected routes)
+    are not shown. If Address is specified (X::X), shows the route
+    that the address matches.
+
+  show ipv6 ospf6 route redistribute (X::X)
+    Shows the routes advertised as AS-External routes by the router
+    itself. If Address is specified (X::X), shows the route
+    that the address matches.
+
+CONFIG NODE:
+  interface NAME
+    To enter INTERFACE NODE
+
+  router ospf6 ...
+    To enter OSPF6 NODE
+
+INTERFACE NODE:
+  ipv6 ospf6 cost COST
+    Sets the interface's output cost. Depends on interface bandwidth by default.
+
+  ipv6 ospf6 hello-interval HELLOINTERVAL
+    Sets the interface's Hello Interval. default 10
+
+  ipv6 ospf6 dead-interval DEADINTERVAL
+    Sets the interface's Router Dead Interval. default 40
+
+  ipv6 ospf6 retransmit-interval RETRANSMITINTERVAL
+    Sets the interface's Rxmt Interval. default 5
+
+  ipv6 ospf6 priority PRIORITY
+    Sets the interface's Router Priority. default 1
+
+  ipv6 ospf6 transmit-delay TRANSMITDELAY
+    Sets the interface's Inf-Trans-Delay. default 1
+
+OSPF6 NODE:
+  router-id A.B.C.D
+    Sets the router's Router-ID
+
+  interface NAME area AREA
+    Binds interface to specified Area, and start
+    sending OSPFv3 packets.
+
+  auto-cost reference-bandwidth COST
+    Sets the reference bandwidth for cost calculations, where this
+    bandwidth is considered equivalent to an OSPF cost of 1, specified
+    in Mbits/s. The default is 100Mbit/s (i.e. a link of bandwidth
+    100Mbit/s or higher will have a cost of 1. Cost of lower bandwidth
+    links will be scaled with reference to this cost).  This
+    configuration setting MUST be consistent across all routers within
+    the OSPF domain.
+
+Sample configuration is in ospf6d.conf.sample.
+
+--
+Yasuhiro Ohara <yasu@sfc.wide.ad.jp>
+Kunihiro Ishiguro <kunihiro@zebra.org>
+