diff options
Diffstat (limited to 'doc/user/isisd.rst')
| -rw-r--r-- | doc/user/isisd.rst | 857 |
1 files changed, 857 insertions, 0 deletions
diff --git a/doc/user/isisd.rst b/doc/user/isisd.rst new file mode 100644 index 0000000..63c9213 --- /dev/null +++ b/doc/user/isisd.rst @@ -0,0 +1,857 @@ +.. _isis: + +**** +ISIS +**** + +:abbr:`ISIS (Intermediate System to Intermediate System)` is a routing protocol +which is described in :t:`ISO10589`, :rfc:`1195`, :rfc:`5308`. ISIS is an +:abbr:`IGP (Interior Gateway Protocol)`. Compared with :abbr:`RIP`, +:abbr:`ISIS` can provide scalable network support and faster convergence times +like :abbr:`OSPF`. ISIS is widely used in large networks such as :abbr:`ISP +(Internet Service Provider)` and carrier backbone networks. + +.. _configuring-isisd: + +Configuring isisd +================= + +There are no *isisd* specific options. Common options can be specified +(:ref:`common-invocation-options`) to *isisd*. *isisd* needs to acquire +interface information from *zebra* in order to function. Therefore *zebra* must +be running before invoking *isisd*. Also, if *zebra* is restarted then *isisd* +must be too. + +Like other daemons, *isisd* configuration is done in :abbr:`ISIS` specific +configuration file :file:`isisd.conf`. + +.. _isis-router: + +ISIS router +=========== + +To start the ISIS process you have to specify the ISIS router. As of this +writing, *isisd* does not support multiple ISIS processes. + +.. clicmd:: router isis WORD [vrf NAME] + + Enable or disable the ISIS process by specifying the ISIS domain with + 'WORD'. *isisd* does not yet support multiple ISIS processes but you must + specify the name of ISIS process. The ISIS process name 'WORD' is then used + for interface (see command :clicmd:`ip router isis WORD`). + +.. clicmd:: net XX.XXXX. ... .XXX.XX + + Set/Unset network entity title (NET) provided in ISO format. + +.. clicmd:: hostname dynamic + + Enable support for dynamic hostname. + +.. clicmd:: area-password [clear | md5] <password> + +.. clicmd:: domain-password [clear | md5] <password> + + Configure the authentication password for an area, respectively a domain, as + clear text or md5 one. + +.. clicmd:: attached-bit [receive ignore | send] + + Set attached bit for inter-area traffic: + + - receive + If LSP received with attached bit set, create default route to neighbor + - send + If L1|L2 router, set attached bit in LSP sent to L1 router + +.. clicmd:: log-adjacency-changes + + Log changes in adjacency state. + +.. clicmd:: log-pdu-drops + + Log any dropped PDUs. + +.. clicmd:: metric-style [narrow | transition | wide] + + Set old-style (ISO 10589) or new-style packet formats: + + - narrow + Use old style of TLVs with narrow metric + - transition + Send and accept both styles of TLVs during transition + - wide + Use new style of TLVs to carry wider metric. FRR uses this as a default value + +.. clicmd:: advertise-high-metrics + + Advertise high metric value on all interfaces to gracefully shift traffic off the router. Reference: :rfc:`3277` + + For narrow metrics, the high metric value is 63; for wide metrics, 16777215; for transition metrics, 62. + +.. clicmd:: set-overload-bit + + Set overload bit to avoid any transit traffic. + +.. clicmd:: set-overload-bit on-startup (0-86400) + + Set overload bit on startup for the specified duration, in seconds. Reference: :rfc:`3277` + +.. clicmd:: purge-originator + + Enable or disable :rfc:`6232` purge originator identification. + +.. clicmd:: lsp-mtu (128-4352) + + Configure the maximum size of generated LSPs, in bytes. + +.. clicmd:: advertise-passive-only + + Advertise prefixes of passive interfaces only. + +.. _isis-timer: + +ISIS Timer +========== + +.. clicmd:: lsp-gen-interval [level-1 | level-2] (1-120) + + Set minimum interval in seconds between regenerating same LSP, + globally, for an area (level-1) or a domain (level-2). + +.. clicmd:: lsp-refresh-interval [level-1 | level-2] (1-65235) + + Set LSP refresh interval in seconds, globally, for an area (level-1) or a + domain (level-2). + +.. clicmd:: max-lsp-lifetime [level-1 | level-2] (360-65535) + + Set LSP maximum LSP lifetime in seconds, globally, for an area (level-1) or + a domain (level-2). + +.. clicmd:: spf-interval [level-1 | level-2] (1-120) + + Set minimum interval between consecutive SPF calculations in seconds. + +.. _isis-fast-reroute: + +ISIS Fast-Reroute +================= + +Unless stated otherwise, commands in this section apply to all LFA +flavors (local LFA, Remote LFA and TI-LFA). + +.. clicmd:: spf prefix-priority [critical | high | medium] WORD + + Assign a priority to the prefixes that match the specified access-list. + + By default loopback prefixes have medium priority and non-loopback prefixes + have low priority. + +.. clicmd:: fast-reroute priority-limit [critical | high | medium] [level-1 | level-2] + + Limit LFA backup computation up to the specified prefix priority. + +.. clicmd:: fast-reroute lfa tiebreaker [downstream | lowest-backup-metric | node-protecting] index (1-255) [level-1 | level-2] + + Configure a tie-breaker for multiple local LFA backups. Lower indexes are + processed first. + +.. clicmd:: fast-reroute load-sharing disable [level-1 | level-2] + + Disable load sharing across multiple LFA backups. + +.. clicmd:: fast-reroute remote-lfa prefix-list [WORD] [level-1 | level-2] + + Configure a prefix-list to select eligible PQ nodes for remote LFA + backups (valid for all protected interfaces). + +.. clicmd:: redistribute <ipv4 | ipv6> table (1-65535) <level-1 | level-2> [metric (0-16777215)|route-map WORD] + + Redistribute routes from a given routing table into the given ISIS + level database. + +.. _isis-region: + +ISIS region +=========== + +.. clicmd:: is-type [level-1 | level-1-2 | level-2-only] + + Define the ISIS router behavior: + + - level-1 + Act as a station router only + - level-1-2 + Act as both a station router and an area router + - level-2-only + Act as an area router only + +.. _isis-interface: + +ISIS interface +============== + +.. _ip-router-isis-word: + +.. clicmd:: <ip|ipv6> router isis WORD + + Activate ISIS adjacency on this interface. Note that the name of ISIS + instance must be the same as the one used to configure the ISIS process (see + command :clicmd:`router isis WORD`). To enable IPv4, issue ``ip router isis + WORD``; to enable IPv6, issue ``ipv6 router isis WORD``. + +.. clicmd:: isis circuit-type [level-1 | level-1-2 | level-2] + + Configure circuit type for interface: + + - level-1 + Level-1 only adjacencies are formed + - level-1-2 + Level-1-2 adjacencies are formed + - level-2-only + Level-2 only adjacencies are formed + +.. clicmd:: isis csnp-interval (1-600) [level-1 | level-2] + + Set CSNP interval in seconds globally, for an area (level-1) or a domain + (level-2). + +.. clicmd:: isis hello padding + + Add padding to IS-IS hello packets. + +.. clicmd:: isis hello padding during-adjacency-formation + + Add padding to IS-IS hello packets during adjacency formation only. + +.. clicmd:: isis hello-interval (1-600) [level-1 | level-2] + + Set Hello interval in seconds globally, for an area (level-1) or a domain + (level-2). + +.. clicmd:: isis hello-multiplier (2-100) [level-1 | level-2] + + Set multiplier for Hello holding time globally, for an area (level-1) or a + domain (level-2). + +.. clicmd:: isis metric [(0-255) | (0-16777215)] [level-1 | level-2] + + Set default metric value globally, for an area (level-1) or a domain + (level-2). Max value depend if metric support narrow or wide value (see + command :clicmd:`metric-style [narrow | transition | wide]`). + +.. clicmd:: isis network point-to-point + + Set network type to 'Point-to-Point' (broadcast by default). + +.. clicmd:: isis passive + + Configure the passive mode for this interface. + +.. clicmd:: isis password [clear | md5] <password> + + Configure the authentication password (clear or encoded text) for the + interface. + +.. clicmd:: isis priority (0-127) [level-1 | level-2] + + Set priority for Designated Router election, globally, for the area + (level-1) or the domain (level-2). + +.. clicmd:: isis psnp-interval (1-120) [level-1 | level-2] + + Set PSNP interval in seconds globally, for an area (level-1) or a domain + (level-2). + +.. clicmd:: isis three-way-handshake + + Enable or disable :rfc:`5303` Three-Way Handshake for P2P adjacencies. + Three-Way Handshake is enabled by default. + +.. clicmd:: isis fast-reroute lfa [level-1 | level-2] + + Enable per-prefix local LFA fast reroute link protection. + +.. clicmd:: isis fast-reroute lfa [level-1 | level-2] exclude interface IFNAME + + Exclude an interface from the local LFA backup nexthop computation. + +.. clicmd:: isis fast-reroute remote-lfa tunnel mpls-ldp [level-1 | level-2] + + Enable per-prefix Remote LFA fast reroute link protection. Note that other + routers in the network need to be configured to accept LDP targeted hello + messages in order for RLFA to work. + +.. clicmd:: isis fast-reroute remote-lfa maximum-metric (1-16777215) [level-1 | level-2] + + Limit Remote LFA PQ node selection within the specified metric. + +.. clicmd:: isis fast-reroute ti-lfa [level-1|level-2] [node-protection [link-fallback]] + + Enable per-prefix TI-LFA fast reroute link or node protection. + When node protection is used, option link-fallback enables the computation and use of + link-protecting LFAs for destinations unprotected by node protection. + +.. _showing-isis-information: + +Showing ISIS information +======================== + +.. clicmd:: show isis [vrf <NAME|all>] summary [json] + + Show summary information about ISIS. + +.. clicmd:: show isis hostname + + Show information about ISIS node. + +.. clicmd:: show isis [vrf <NAME|all>] interface [detail] [IFNAME] [json] + + Show state and configuration of ISIS specified interface, or all interfaces + if no interface is given with or without details. + +.. clicmd:: show isis [vrf <NAME|all>] neighbor [detail] [SYSTEMID] [json] + + Show state and information of ISIS specified neighbor, or all neighbors if + no system id is given with or without details. + +.. clicmd:: show isis [vrf <NAME|all>] database [detail] [LSPID] [json] + + Show the ISIS database globally, for a specific LSP id without or with + details. + +.. clicmd:: show isis topology [level-1|level-2] [algorithm (128-255)] + + Show topology IS-IS paths to Intermediate Systems, globally, in area + (level-1) or domain (level-2). + +.. clicmd:: show isis route [level-1|level-2] [prefix-sid|backup] [algorithm (128-255)] + + Show the ISIS routing table, as determined by the most recent SPF + calculation. + +.. clicmd:: show isis fast-reroute summary [level-1|level-2] + + Show information about the number of prefixes having LFA protection, + and network-wide LFA coverage. + + +.. _isis-traffic-engineering: + +Traffic Engineering +=================== + +.. note:: + + IS-IS-TE supports RFC 5305 (base TE), RFC 6119 (IPv6) and RFC 7810 / 8570 + (Extended Metric) with or without Multi-Topology. All Traffic Engineering + information are stored in a database formally named TED. However, best + acccuracy is provided without Multi-Topology due to inconsistency of Traffic + Engineering Advertisement of 3rd party commercial routers when MT is enabled. + At this time, FRR offers partial support for some of the routing protocol + extensions that can be used with MPLS-TE. FRR does not currently support a + complete RSVP-TE solution. + +.. clicmd:: mpls-te on + + Enable Traffic Engineering LSP flooding. + +.. clicmd:: mpls-te router-address <A.B.C.D> + + Configure stable IP address for MPLS-TE. + +.. clicmd:: mpls-te router-address ipv6 <X:X::X:X> + + Configure stable IPv6 address for MPLS-TE. + +.. clicmd:: mpls-te export + + Export Traffic Engineering DataBase to other daemons through the ZAPI + Opaque Link State messages. + +.. clicmd:: show isis mpls-te interface + +.. clicmd:: show isis mpls-te interface INTERFACE + + Show MPLS Traffic Engineering parameters for all or specified interface. + +.. clicmd:: show isis mpls-te router + + Show Traffic Engineering router parameters. + +.. clicmd:: show isis [vrf <NAME|all>] mpls-te database [detail|json] + +.. clicmd:: show isis [vrf <NAME|all>] mpls-te database vertex [WORD] [detail|json] + +.. clicmd:: show isis [vrf <NAME|all>] mpls-te database edge [A.B.C.D|X:X::X:X] [detail|json] + +.. clicmd:: show isis [vrf <NAME|all>] mpls-te database subnet [A.B.C.D/M|X:X::X:X/M] [detail|json] + + Show Traffic Engineering Database + +.. seealso:: + + :ref:`ospf-traffic-engineering` + +.. _isis-segment-routing: + +Segment Routing +=============== + +This is an EXPERIMENTAL support of Segment Routing as per RFC8667 +for MPLS dataplane. It supports IPv4, IPv6 and ECMP and has been +tested against Cisco & Juniper routers. + +Known limitations: + - No support for level redistribution (L1 to L2 or L2 to L1) + - No support for binding SID + - No support for SRMS + - No support for SRLB + - Only one SRGB and default SPF Algorithm is supported + +.. clicmd:: segment-routing on + + Enable Segment Routing. + +.. clicmd:: segment-routing global-block (16-1048575) (16-1048575) [local-block (16-1048575) (16-1048575)] + + Set the Segment Routing Global Block i.e. the label range used by MPLS + to store label in the MPLS FIB for Prefix SID. Note that the block size + may not exceed 65535. Optionally sets also the Segment Routing Local Block. + The negative command always unsets both. + +.. clicmd:: segment-routing node-msd (1-16) + + Set the Maximum Stack Depth supported by the router. The value depend of the + MPLS dataplane. E.g. for Linux kernel, since version 4.13 the maximum value + is 32. + +.. clicmd:: segment-routing prefix <A.B.C.D/M|X:X::X:X/M> [algorithm (128-255)] <absolute (16-1048575)|index (0-65535) [no-php-flag|explicit-null] [n-flag-clear] + + prefix. The 'no-php-flag' means NO Penultimate Hop Popping that allows SR + node to request to its neighbor to not pop the label. The 'explicit-null' + flag allows SR node to request to its neighbor to send IP packet with the + EXPLICIT-NULL label. The 'n-flag-clear' option can be used to explicitly + clear the Node flag that is set by default for Prefix-SIDs associated to + loopback addresses. This option is necessary to configure Anycast-SIDs. + +.. clicmd:: show isis segment-routing node [algorithm (128-255)] + + Show detailed information about all learned Segment Routing Nodes. + +.. _isis-flex-algo: + +Flex-Algos (Flex-Algo) +====================== + +*isisd* supports some features of +`RFC 9350 <https://tools.ietf.org/html/rfc9350>`_ on an MPLS Segment-Routing +dataplane. The compatibility has been tested against Cisco. + +IS-IS uses by default the `Shortest-Path-First` algorithm that basically +calculates paths based on the shortest total metric to the destinations. +Flex-Algo allows new algorithms to run in parallel to compute paths in different +manners, based on metrics (IGP metric or a new type of metrics such as Traffic +Engineering (TE) metric and minimum delay...) and constraints. New metric types +are not yet implemented but constraints are already operational. Constraints can +restrict paths to links with specific affinities or avoid links with specific +affinities. Combinations of these are also possible. + +The administrator can configure up to 128 Flex-Algos in an IS-IS area. +To do so, it defines a set of Flex-Algo Definitions (FAD) which +have the following characteristics: + +- a numeric identifier (ID) between 128 and 255 inclusive +- a set of constraints (basically, include or exclude a certain given set of + links, designated by a admin-group) +- the calculation type (only the `Shortest-Path-First` is currently supported) +- the metric type (only the IGP inherited metric type is currently supported) +- some additional flags (not supported for the moment). + +A subset of routers advertises the Flex-Algo Definitions (FAD) to the other +routers within an area. In order to use a common set of FADs, each router runs a +FAD election process for each locally configured algorithm, using the following +rules: + +- If a locally configured FAD is not advertised to the area, the router does not + participate in the particular flex algorithm. +- If a given flex algorithm is running, the participation in this particular + flex algorithm stops when its advertisements are over. +- A router includes its own FAD in the election process if and only if it is + advertised to the other routers. +- If only one router advertises the FAD, the FAD is elected. +- If several FADs are advertised with different priorities, the one with the + highest priority value is selected. +- If there are multiple advertisements of the FAD with the same highest + priority, the FAD of the router with the highest IS-IS system-ID is + selected. + +Routers only use the specifications of the elected FAD regardless of the locally +configured definitions. If a router does not support one of the FAD +characteristics, it stops participating in the Flex-Algo. + +For each running Flex-Algo, the Segment-Routing SIDs must be +configured with values unique to the algorithm. It allows routers to identify +which flex algorithm they must use for a given packet. + +The following commands configure Flex-Algo at the 'router isis' configuration +level. Segment-Routing prefixes must be configured for the Flex-Algo. + +.. clicmd:: flexible-algorithm (128-255) + + Add a Flex-Algo Definition (FAD) and enter the FAD configuration + level. The algorithm ID value is in the range of 128 to 255 inclusive. + +.. clicmd:: no flexible-algorithm (128-255) + + Unconfigure a Flex-Algo Definition. + +.. clicmd:: affinity-map NAME bit-position (0-255) + + Add the specified 'affinity-map'. Affinity-map definitions are used in + FADs and in interfaces admin-group definition. + + Affinity-maps format in advertisement TLVs use the extended admin-group + format defined in the RFC7308 section 2.2. The extended admin-group uses a + 256 bits field. If an affinity-map is set, the bit at the extended + admin-group 'bit-position' is set 1, else it is set to 0. + +The following commands configure Flex-Algo at the 'router isis' and +'flexible-algorithm (128-255)' configuration level. + +.. clicmd:: advertise-definition + + Advertise the current FAD to other IS-IS routers by using specific IS-IS + TLVs. By default, the definition is is not shared with other routers. + + A router can advertise a FAD without participating in the Flex-Algo. + +.. clicmd:: priority (0-255) + + Set the specified 'priority' in the current FAD advertisements . + +.. clicmd:: metric-type [igp|te|delay] + + Set the 'metric-type' for the current FAD. 'igp' is + the default value and refers to the classic 'Shortest-Path-First' algorithm. + If the 'te' or the 'delay' metric is selected, the value is advertised but + the flex algorithm is disabled locally because these types are not currently + supported. + +.. clicmd:: no metric-type + + Reset the 'metric-type' to the default 'igp' metric. + +.. clicmd:: affinity exclude-any NAME + + Add the specified affinity to the list of exclude-any affinities. The + Flex-Algo will compute paths that exclude the segments with any of + the specified affinities. + +.. clicmd:: no affinity exclude-any NAME + + Remove the specified affinity to the list of exclude-any affinities. + +.. clicmd:: affinity include-all NAME + + Add the specified affinity to the list of include-all affinities. The + Flex-Algo will compute paths that include the segments with all + the specified affinities. + +.. clicmd:: no affinity include-all NAME + + Remove the specified affinity to the list of include-all affinities. + +.. clicmd:: affinity include-any NAME + + Add the specified affinity to the list of include-any affinities. The + Flex-Algo will compute paths that include the segments with any of + the specified affinities. + +.. clicmd:: no affinity include-any NAME + + Remove the specified affinity to the list of include-any affinities. + +The following commands configure Flex-Algo at the 'interface' configuration +level. + +.. clicmd:: isis affinity flex-algo NAME + + Add the specified affinity to the interface. + +.. clicmd:: no isis affinity flex-algo NAME + + Remove the specified affinity from the interface. + +The following command show Flex-Algo information: + +.. clicmd:: show isis flex-algo [(128-255)] + + Show information about the elected FADs + +'show isis route', 'show isis topology' and 'show isis segment-routing node' +includes an 'algorithm (128-255)' optional argument. See +:ref:`showing-isis-information` and :ref:`isis-segment-routing`. + +.. _isis-srv6: + +Segment Routing over IPv6 (SRv6) +================================ + +This feature enables extensions in IS-IS to support Segment Routing over IPv6 +data plane (SRv6) as per RFC 9352. + +.. clicmd:: segment-routing srv6 + + Enable Segment Routing over IPv6 data plane (SRv6). + +.. clicmd:: locator NAME + + Specify the SRv6 locator to use for SRv6. The locator must be configured in + Zebra. Once the locator is configured, IS-IS automatically allocates prefix + SID and adjacency SIDs, creates local SID entries in the data plane, and + advertises them in the IGP domain. + +.. clicmd:: interface NAME + + Specify the dummy interface used to install SRv6 SIDs in the Linux data plane. + The interface must be created manually. By default, the interface is 'sr0'. + The interface can be created using the iproute2 utility: + + .. code-block:: bash + + ip link add sr0 type dummy + ip link set sr0 up + +.. clicmd:: show isis segment-routing srv6 node + + Show detailed information about all learned SRv6 Nodes. + +Debugging ISIS +============== + +.. clicmd:: debug isis adj-packets + + IS-IS Adjacency related packets. + +.. clicmd:: debug isis checksum-errors + + IS-IS LSP checksum errors. + +.. clicmd:: debug isis events + + IS-IS Events. + +.. clicmd:: debug isis local-updates + + IS-IS local update packets. + +.. clicmd:: debug isis packet-dump + + IS-IS packet dump. + +.. clicmd:: debug isis protocol-errors + + IS-IS LSP protocol errors. + +.. clicmd:: debug isis route-events + + IS-IS Route related events. + +.. clicmd:: debug isis snp-packets + + IS-IS CSNP/PSNP packets. + +.. clicmd:: debug isis spf-events +.. clicmd:: debug isis spf-statistics +.. clicmd:: debug isis spf-triggers + + IS-IS Shortest Path First Events, Timing and Statistic Data and triggering + events. + +.. clicmd:: debug isis update-packets + + + Update related packets. + +.. clicmd:: debug isis te-events + + IS-IS Traffic Engineering events + +.. clicmd:: debug isis sr-events + + + IS-IS Segment Routing events. + +.. clicmd:: debug isis lfa + + + IS-IS LFA events. + +.. clicmd:: show debugging isis + + Print which ISIS debug level is activate. + +.. _isis-config-examples: + +ISIS Configuration Examples +=========================== + +A simple example, with MD5 authentication enabled: + +.. code-block:: frr + + ! + interface eth0 + ip router isis FOO + isis network point-to-point + isis circuit-type level-2-only + ! + router isis FOO + net 47.0023.0000.0000.0000.0000.0000.0000.1900.0004.00 + metric-style wide + is-type level-2-only + + +A Traffic Engineering configuration, with Inter-ASv2 support. + +First, the :file:`zebra.conf` part: + +.. code-block:: frr + + hostname HOSTNAME + password PASSWORD + log file /var/log/zebra.log + ! + interface eth0 + ip address 10.2.2.2/24 + link-params + max-bw 1.25e+07 + max-rsv-bw 1.25e+06 + unrsv-bw 0 1.25e+06 + unrsv-bw 1 1.25e+06 + unrsv-bw 2 1.25e+06 + unrsv-bw 3 1.25e+06 + unrsv-bw 4 1.25e+06 + unrsv-bw 5 1.25e+06 + unrsv-bw 6 1.25e+06 + unrsv-bw 7 1.25e+06 + admin-grp 0xab + ! + interface eth1 + ip address 10.1.1.1/24 + link-params + enable + metric 100 + max-bw 1.25e+07 + max-rsv-bw 1.25e+06 + unrsv-bw 0 1.25e+06 + unrsv-bw 1 1.25e+06 + unrsv-bw 2 1.25e+06 + unrsv-bw 3 1.25e+06 + unrsv-bw 4 1.25e+06 + unrsv-bw 5 1.25e+06 + unrsv-bw 6 1.25e+06 + unrsv-bw 7 1.25e+06 + neighbor 10.1.1.2 as 65000 + + +Then the :file:`isisd.conf` itself: + +.. code-block:: frr + + hostname HOSTNAME + password PASSWORD + log file /var/log/isisd.log + ! + ! + interface eth0 + ip router isis FOO + ! + interface eth1 + ip router isis FOO + ! + ! + router isis FOO + isis net 47.0023.0000.0000.0000.0000.0000.0000.1900.0004.00 + mpls-te on + mpls-te router-address 10.1.1.1 + ! + line vty + +A Segment Routing configuration, with IPv4, IPv6, SRGB and MSD configuration. + +.. code-block:: frr + + hostname HOSTNAME + password PASSWORD + log file /var/log/isisd.log + ! + ! + interface eth0 + ip router isis SR + isis network point-to-point + ! + interface eth1 + ip router isis SR + ! + ! + router isis SR + net 49.0000.0000.0000.0001.00 + is-type level-1 + topology ipv6-unicast + lsp-gen-interval 2 + segment-routing on + segment-routing node-msd 8 + segment-routing prefix 10.1.1.1/32 index 100 explicit-null + segment-routing prefix 2001:db8:1000::1/128 index 101 explicit-null + ! + +An SRv6 configuration: + +.. code-block:: frr + + hostname HOSTNAME + password PASSWORD + log file /var/log/isisd.log + ! + ! + interface eth0 + ipv6 router isis FOO + ip router isis FOO + isis hello-interval 5 + ! + interface eth1 + ip router isis FOO + ! + ! + router isis FOO + net 49.0001.1111.1111.1111.00 + is-type level-2-only + metric-style wide + segment-routing srv6 + locator loc1 + ! + line vty + + +.. _isis-vrf-config-examples: + +ISIS Vrf Configuration Examples +=============================== + +A simple vrf example: + +.. code-block:: frr + + ! + interface eth0 vrf RED + ip router isis FOO vrf RED + isis network point-to-point + isis circuit-type level-2-only + ! + router isis FOO vrf RED + net 47.0023.0000.0000.0000.0000.0000.0000.1900.0004.00 + metric-style wide + is-type level-2-only |