diff options
Diffstat (limited to '')
| -rw-r--r-- | doc/user/zebra.rst | 100 |
1 files changed, 77 insertions, 23 deletions
diff --git a/doc/user/zebra.rst b/doc/user/zebra.rst index ba6e3bf..30b0204 100644 --- a/doc/user/zebra.rst +++ b/doc/user/zebra.rst @@ -50,7 +50,8 @@ Besides the common invocation options (:ref:`common-invocation-options`), the When *Zebra* starts with this option, the VRF backend is based on Linux network namespaces. That implies that all network namespaces discovered by ZEBRA will create an associated VRF. The other daemons will operate on the VRF - VRF defined by *Zebra*, as usual. + VRF defined by *Zebra*, as usual. If this option is specified when running + *Zebra*, one must also specify the same option for *mgmtd*. .. seealso:: :ref:`zebra-vrf` @@ -177,16 +178,15 @@ Standard Commands work on non-linux systems at all. 'enable' and 'disable' will respectively turn on and off mpls on the given interface. -.. clicmd:: multicast +.. clicmd:: multicast <enable|disable> Enable or disable multicast flag for the interface. -.. clicmd:: bandwidth (1-10000000) +.. clicmd:: bandwidth (1-1000000) - - Set bandwidth value of the interface in kilobits/sec. This is for + Set bandwidth value of the interface in Megabits/sec. This is for calculating OSPF cost. This command does not affect the actual device configuration. @@ -213,20 +213,14 @@ Link Parameters Commands .. clicmd:: link-params + Enter into the link parameters sub node. This command activates the link + parameters and allows to configure routing information that could be used + as part of Traffic Engineering on this interface. MPLS-TE must be enabled at + the OSPF (:ref:`ospf-traffic-engineering`) or ISIS + (:ref:`isis-traffic-engineering`) router level in complement to this. To + disable link parameters, use the ``no`` version of this command. - Enter into the link parameters sub node. At least 'enable' must be - set to activate the link parameters, and consequently routing - information that could be used as part of Traffic Engineering on - this interface. MPLS-TE must be enable at the OSPF - (:ref:`ospf-traffic-engineering`) or ISIS - (:ref:`isis-traffic-engineering`) router level in complement to - this. - - Under link parameter statement, the following commands set the different TE values: - -.. clicmd:: enable - - Enable link parameters for this interface. +Under link parameter statement, the following commands set the different TE values: .. clicmd:: metric (0-4294967295) @@ -252,7 +246,7 @@ Link Parameters Commands as specified in RFC3630 (OSPF) or RFC5305 (ISIS). Admin-group is also known as Resource Class/Color in the OSPF protocol. -.. clicmd:: [no] affinity AFFINITY-MAP-NAME +.. clicmd:: affinity AFFINITY-MAP-NAME This commands configures the Traffic Engineering Admin-Group of the interface using the affinity-map definitions (:ref:`affinity-map`). @@ -263,7 +257,7 @@ Link Parameters Commands ``admin-grp`` and ``affinity`` commands provide two ways of setting admin-groups. They cannot be both set on the same interface. -.. clicmd:: [no] affinity-mode [extended|standard|both] +.. clicmd:: affinity-mode [extended|standard|both] This commands configures which admin-group format is set by the affinity command. ``extended`` Admin-Group is the default and uses the RFC7308 format. @@ -783,9 +777,25 @@ presence of the entry. 21 Static 10.125.0.2 IPv4 Explicit Null +MPLS label chunks +----------------- + +MPLS label chunks are handled in the zebra label manager service, +which ensures a same label value or label chunk can not be used by +multiple CP routing daemons at the same time. + +Label requests originate from CP routing daemons, and are resolved +over the default MPLS range (16-1048575). There are two kind of +requests: +- Static label requests request an exact label value or range. For +instance, segment routing label blocks requests originating from +IS-IS are part of it. +- Dynamic label requests only need a range of label values. The +'bgp l3vpn export auto' command uses such requests. + Allocated label chunks table can be dumped using the command -.. clicmd:: show debugging label-table +.. clicmd:: show debugging label-table [json] :: @@ -796,6 +806,15 @@ Allocated label chunks table can be dumped using the command Proto ospf: [20000/21000] Proto isis: [22000/23000] +.. clicmd:: mpls label dynamic-block (16-1048575) (16-1048575) + + Define a range of labels where dynamic label requests will + allocate label chunks from. This command guarantees that + static label values outside that range will not conflict + with the dynamic label requests. When the dynamic-block + range is configured, static label requests that match that + range are not accepted. + .. _zebra-srv6: Segment-Routing IPv6 @@ -813,6 +832,35 @@ FRR's cli or frr.conf or zebra.conf. This section shows how to configure SRv6 on FRR. Of course SRv6 can be used as standalone, and this section also helps that case. +.. clicmd:: show segment-routing srv6 manager [json] + + This command dumps the SRv6 information configured on zebra, including + the encapsulation parameters (e.g., the IPv6 source address used for + the encapsulated packets). + + Example:: + + router# sh segment-routing srv6 manager + Parameters: + Encapsulation: + Source Address: + Configured: fc00:0:1::1 + + + To get the same information in json format, you can use the ``json`` keyword:: + + rose-srv6# sh segment-routing srv6 manager json + { + "parameters":{ + "encapsulation":{ + "sourceAddress":{ + "configured":"fc00:0:1::1" + } + } + } + } + + .. clicmd:: show segment-routing srv6 locator [json] This command dump SRv6-locator configured on zebra. SRv6-locator is used @@ -973,6 +1021,14 @@ and this section also helps that case. ! ... +.. clicmd:: encapsulation + + Configure parameters for SRv6 encapsulation. + +.. clicmd:: source-address X:X::X:X + + Configure the source address of the outer encapsulating IPv6 header. + .. _multicast-rib-commands: Multicast RIB Commands @@ -1434,8 +1490,6 @@ zebra Terminal Mode Commands .. clicmd:: show ip prefix-list [NAME] -.. clicmd:: show route-map [NAME] - .. clicmd:: show ip protocol .. clicmd:: show ip forward |