1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
|
/* -*- Mode: C++; tab-width: 4; indent-tabs-mode: nil; c-basic-offset: 4 -*- */
/*
* This file is part of the LibreOffice project.
*
* This Source Code Form is subject to the terms of the Mozilla Public
* License, v. 2.0. If a copy of the MPL was not distributed with this
* file, You can obtain one at http://mozilla.org/MPL/2.0/.
*
* This file incorporates work covered by the following license notice:
*
* Licensed to the Apache Software Foundation (ASF) under one or more
* contributor license agreements. See the NOTICE file distributed
* with this work for additional information regarding copyright
* ownership. The ASF licenses this file to you under the Apache
* License, Version 2.0 (the "License"); you may not use this file
* except in compliance with the License. You may obtain a copy of
* the License at http://www.apache.org/licenses/LICENSE-2.0 .
*/
#pragma once
#include <basegfx/numeric/ftools.hxx>
#include <basegfx/polygon/b2dpolypolygon.hxx>
#include <basegfx/polygon/b2dpolygon.hxx>
#include <com/sun/star/drawing/LineCap.hpp>
#include <basegfx/basegfxdllapi.h>
namespace basegfx::utils
{
/** Create line start/end geometry element, mostly arrows and things like that.
@param rCandidate
The polygon which needs to get that line ends and needs to have two points
at least.
@param rArrow
The line start/end geometry. It is assumed that the tip is pointing
upwards. Result will be rotated and scaled to fit.
@param bStart
describes if creation is for start or end of candidate.
@param fWidth
defines the size of the element, it's describing the target width in X
of the arrow.
@param fDockingPosition needs to be in [0.0 ..1.0] range, where 0.0 means
that the tip of the arrow will be aligned with the polygon start, 1.0 means
the bottom. The default of 0.5 describes a centered arrow.
@param pConsumedLength
Using this parameter it is possible to get back how much from the candidate
geometry is overlapped by the created element (consumed).
@param fCandidateLength
This should contain the length of rCandidate to allow work without
again calculating the length (which may be expensive with beziers). If 0.0 is
given, the length is calculated on demand.
@param fShift
When it is necessary to count with the thickness of the line, it
makes sense to move the start position slightly - so define the shift.
@return
The Line start and end polygon, correctly rotated and scaled
*/
BASEGFX_DLLPUBLIC B2DPolyPolygon createAreaGeometryForLineStartEnd(
const B2DPolygon& rCandidate,
const B2DPolyPolygon& rArrow,
bool bStart,
double fWidth,
double fCandidateLength, // 0.0 -> calculate self
double fDockingPosition, // 0->top, 1->bottom
double* pConsumedLength = nullptr,
double fShift = 0.0);
/** create filled polygon geometry for lines with a line width
This method will create bezier based, fillable polygons which
will resample the curve if it was extended for the given half
line width. It will remove extrema positions from contained
bezier segments and get as close as possible and defined by
the given parameters to the ideal result.
It will check edges for trivial bezier to avoid unnecessary
bezier polygons. Care is taken to produce the in-between
polygon points (the ones original on the source polygon) since
it has showed that without those, the raster converters leave
non-filled gaps.
@param rCandidate
The source polygon defining the hairline polygon path
@param fHalfLineWidth
The width of the line to one side
@param eJoin
The LineJoin if the edges meeting in a point do not have a C1
or C2 continuity
@param eCap
The kind of cap, which is added to the line.
@param fMaxAllowedAngle
Allows to hand over the maximum allowed angle between an edge and
it's control vectors. The smaller, the more subdivisions will be
needed to create the filled geometry. Allowed range is cropped to
[M_PI_2 .. 0.01 * M_PI_2].
@param fMaxPartOfEdge
Allows to influence from with relative length of a control vector
compared to its edge a split is forced. The smaller, the more
subdivisions will be needed to create the filled geometry. Allowed
range is cropped to [1.0 .. 0.01]
@param fMiterMinimumAngle
The minimum wanted angle between two edges when edge rounding
is using miter. When an edge is smaller than this (tighter)
the usual fallback to bevel is used. Allowed range is cropped
to [M_PI .. 0.01 * M_PI].
Commit 51b5b93092d6231615de470c62494c24e54828a1 needs
revert, we need the triangulation for X11 fat line drawing
@param pTriangles
If given, the method will additionally add the created geometry as
B2DTriangle's
@return
The tools::PolyPolygon containing the geometry of the extended line by
it's line width. Contains bezier segments and edge roundings as
needed and defined.
*/
BASEGFX_DLLPUBLIC B2DPolyPolygon createAreaGeometry(
const B2DPolygon& rCandidate,
double fHalfLineWidth,
B2DLineJoin eJoin,
css::drawing::LineCap eCap,
double fMaxAllowedAngle = basegfx::deg2rad(12.5),
double fMaxPartOfEdge = 0.4,
double fMiterMinimumAngle = basegfx::deg2rad(15.0));
} // end of namespace basegfx::utils
/* vim:set shiftwidth=4 softtabstop=4 expandtab: */
|
