Adding upstream version 6.6.15.upstream/6.6.15

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 181 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/sound/cs35l35.txt b/Documentation/devicetree/bindings/sound/cs35l35.txt
new file mode 100644
index 0000000000..e84f30c5c3
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/cs35l35.txt
@@ -0,0 +1,181 @@
+CS35L35 Boosted Speaker Amplifier
+
+Required properties:
+
+  - compatible : "cirrus,cs35l35"
+
+  - reg : the I2C address of the device for I2C
+
+  - VA-supply, VP-supply : power supplies for the device,
+    as covered in
+    Documentation/devicetree/bindings/regulator/regulator.txt.
+
+  - interrupts : IRQ line info CS35L35.
+    (See Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
+    for further information relating to interrupt properties)
+
+ - cirrus,boost-ind-nanohenry: Inductor value for boost converter. The value is
+    in nH and they can be values of 1000nH, 1200nH, 1500nH, and 2200nH.
+
+Optional properties:
+  - reset-gpios : gpio used to reset the amplifier
+
+  - cirrus,stereo-config : Boolean to determine if there are 2 AMPs for a
+  Stereo configuration
+
+  - cirrus,audio-channel : Set Location of Audio Signal on Serial Port
+  0 = Data Packet received on Left I2S Channel
+  1 = Data Packet received on Right I2S Channel
+
+  - cirrus,advisory-channel : Set Location of Advisory Signal on Serial Port
+  0 = Data Packet received on Left I2S Channel
+  1 = Data Packet received on Right I2S Channel
+
+  - cirrus,shared-boost : Boolean to enable ClassH tracking of Advisory Signal
+  if 2 Devices share Boost BST_CTL
+
+  - cirrus,external-boost : Boolean to specify the device is using an external
+  boost supply, note that sharing a boost from another cs35l35 would constitute
+  using an external supply for the slave device
+
+  - cirrus,sp-drv-strength : Value for setting the Serial Port drive strength
+  Table 3-10 of the datasheet lists drive-strength specifications
+  0 = 1x (Default)
+  1 = .5x
+  - cirrus,sp-drv-unused : Determines how unused slots should be driven on the
+  Serial Port.
+  0 - Hi-Z
+  2 - Drive 0's (Default)
+  3 - Drive 1's
+
+  - cirrus,bst-pdn-fet-on : Boolean to determine if the Boost PDN control
+  powers down with a rectification FET On or Off. If VSPK is supplied
+  externally then FET is off.
+
+  - cirrus,boost-ctl-millivolt : Boost Voltage Value.  Configures the boost
+    converter's output voltage in mV. The range is from 2600mV to 9000mV with
+    increments of 100mV.
+    (Default) VP
+
+  - cirrus,boost-peak-milliamp : Boost-converter peak current limit in mA.
+  Configures the peak current by monitoring the current through the boost FET.
+  Range starts at 1680mA and goes to a maximum of 4480mA with increments of
+  110mA.
+  (Default) 2.46 Amps
+
+  - cirrus,amp-gain-zc : Boolean to determine if to use Amplifier gain-change
+  zero-cross
+
+Optional H/G Algorithm sub-node:
+
+  The cs35l35 node can have a single "cirrus,classh-internal-algo" sub-node
+  that will disable automatic control of the internal H/G Algorithm.
+
+  It is strongly recommended that the Datasheet be referenced when adjusting
+  or using these Class H Algorithm controls over the internal Algorithm.
+  Serious damage can occur to the Device and surrounding components.
+
+  - cirrus,classh-internal-algo : Sub-node for the Internal Class H Algorithm
+  See Section 4.3 Internal Class H Algorithm in the Datasheet.
+  If not used, the device manages the ClassH Algorithm internally.
+
+Optional properties for the "cirrus,classh-internal-algo" Sub-node
+
+  Section 7.29 Class H Control
+  - cirrus,classh-bst-overide : Boolean
+  - cirrus,classh-bst-max-limit
+  - cirrus,classh-mem-depth
+
+  Section 7.30 Class H Headroom Control
+  - cirrus,classh-headroom
+
+  Section 7.31 Class H Release Rate
+  - cirrus,classh-release-rate
+
+  Section 7.32 Class H Weak FET Drive Control
+  - cirrus,classh-wk-fet-disable
+  - cirrus,classh-wk-fet-delay
+  - cirrus,classh-wk-fet-thld
+
+  Section 7.34 Class H VP Control
+  - cirrus,classh-vpch-auto
+  - cirrus,classh-vpch-rate
+  - cirrus,classh-vpch-man
+
+Optional Monitor Signal Format sub-node:
+
+  The cs35l35 node can have a single "cirrus,monitor-signal-format" sub-node
+  for adjusting the Depth, Location and Frame of the Monitoring Signals
+  for Algorithms.
+
+  See Sections 4.8.2 through 4.8.4 Serial-Port Control in the Datasheet
+
+  -cirrus,monitor-signal-format : Sub-node for the Monitor Signaling Formatting
+  on the I2S Port. Each of the 3 8 bit values in the array contain the settings
+  for depth, location, and frame.
+
+  If not used, the defaults for the 6 monitor signals is used.
+
+  Sections 7.44 - 7.53 lists values for the depth, location, and frame
+  for each monitoring signal.
+
+  - cirrus,imon : 4 8 bit values to set the depth, location, frame and ADC
+  scale of the IMON monitor signal.
+
+  - cirrus,vmon : 3 8 bit values to set the depth, location, and frame
+  of the VMON monitor signal.
+
+  - cirrus,vpmon : 3 8 bit values to set the depth, location, and frame
+  of the VPMON monitor signal.
+
+  - cirrus,vbstmon : 3 8 bit values to set the depth, location, and frame
+  of the VBSTMON monitor signal
+
+  - cirrus,vpbrstat : 3 8 bit values to set the depth, location, and frame
+  of the VPBRSTAT monitor signal
+
+  - cirrus,zerofill : 3 8 bit values to set the depth, location, and frame\
+  of the ZEROFILL packet in the monitor signal
+
+Example:
+
+cs35l35: cs35l35@20 {
+	compatible = "cirrus,cs35l35";
+	reg = <0x20>;
+	VA-supply = <&dummy_vreg>;
+	VP-supply = <&dummy_vreg>;
+	reset-gpios = <&axi_gpio 54 0>;
+	interrupt-parent = <&gpio8>;
+	interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+	cirrus,boost-ctl-millivolt = <9000>;
+
+	cirrus,stereo-config;
+	cirrus,audio-channel = <0x00>;
+	cirrus,advisory-channel = <0x01>;
+	cirrus,shared-boost;
+
+	cirrus,classh-internal-algo {
+		cirrus,classh-bst-overide;
+		cirrus,classh-bst-max-limit = <0x01>;
+		cirrus,classh-mem-depth = <0x01>;
+		cirrus,classh-release-rate = <0x08>;
+		cirrus,classh-headroom-millivolt = <0x0B>;
+		cirrus,classh-wk-fet-disable = <0x01>;
+		cirrus,classh-wk-fet-delay = <0x04>;
+		cirrus,classh-wk-fet-thld = <0x01>;
+		cirrus,classh-vpch-auto = <0x01>;
+		cirrus,classh-vpch-rate = <0x02>;
+		cirrus,classh-vpch-man = <0x05>;
+	};
+
+	/* Depth, Location, Frame */
+	cirrus,monitor-signal-format {
+		cirrus,imon = /bits/ 8 <0x03 0x00 0x01>;
+		cirrus,vmon = /bits/ 8 <0x03 0x00 0x00>;
+		cirrus,vpmon = /bits/ 8 <0x03 0x04 0x00>;
+		cirrus,vbstmon = /bits/ 8 <0x03 0x04 0x01>;
+		cirrus,vpbrstat = /bits/ 8 <0x00 0x04 0x00>;
+		cirrus,zerofill = /bits/ 8 <0x00 0x00 0x00>;
+	};
+
+};