Adding upstream version 6.6.15.upstream/6.6.15

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 161 insertions, 0 deletions

diff --git a/arch/arc/boot/dts/axc003.dtsi b/arch/arc/boot/dts/axc003.dtsi
new file mode 100644
index 0000000000..3434c8131e
--- /dev/null
+++ b/arch/arc/boot/dts/axc003.dtsi
@@ -0,0 +1,161 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2014-15 Synopsys, Inc. (www.synopsys.com)
+ */
+
+/*
+ * Device tree for AXC003 CPU card: HS38x UP configuration
+ */
+
+/include/ "skeleton_hs.dtsi"
+
+/ {
+	compatible = "snps,arc";
+	#address-cells = <2>;
+	#size-cells = <2>;
+
+	cpu_card {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		ranges = <0x00000000 0x0 0xf0000000 0x10000000>;
+
+		input_clk: input-clk {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <33333333>;
+		};
+
+		core_clk: core-clk@80 {
+			compatible = "snps,axs10x-arc-pll-clock";
+			reg = <0x80 0x10>, <0x100 0x10>;
+			#clock-cells = <0>;
+			clocks = <&input_clk>;
+
+			/*
+			 * Set initial core pll output frequency to 90MHz.
+			 * It will be applied at the core pll driver probing
+			 * on early boot.
+			 */
+			assigned-clocks = <&core_clk>;
+			assigned-clock-rates = <90000000>;
+		};
+
+		core_intc: archs-intc@cpu {
+			compatible = "snps,archs-intc";
+			interrupt-controller;
+			#interrupt-cells = <1>;
+		};
+
+		/*
+		 * this GPIO block ORs all interrupts on CPU card (creg,..)
+		 * to uplink only 1 IRQ to ARC core intc
+		 */
+		dw-apb-gpio@2000 {
+			compatible = "snps,dw-apb-gpio";
+			reg = < 0x2000 0x80 >;
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			ictl_intc: gpio-controller@0 {
+				compatible = "snps,dw-apb-gpio-port";
+				gpio-controller;
+				#gpio-cells = <2>;
+				snps,nr-gpios = <30>;
+				reg = <0>;
+				interrupt-controller;
+				#interrupt-cells = <2>;
+				interrupt-parent = <&core_intc>;
+				interrupts = <25>;
+			};
+		};
+
+		debug_uart: dw-apb-uart@5000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x5000 0x100>;
+			clock-frequency = <33333000>;
+			interrupt-parent = <&ictl_intc>;
+			interrupts = <2 4>;
+			baud = <115200>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+		};
+
+		arcpct0: pct {
+			compatible = "snps,archs-pct";
+			#interrupt-cells = <1>;
+			interrupt-parent = <&core_intc>;
+			interrupts = <20>;
+		};
+	};
+
+	/*
+	 * Mark DMA peripherals connected via IOC port as dma-coherent. We do
+	 * it via overlay because peripherals defined in axs10x_mb.dtsi are
+	 * used for both AXS101 and AXS103 boards and only AXS103 has IOC (so
+	 * only AXS103 board has HW-coherent DMA peripherals)
+	 * We don't need to mark pgu@17000 as dma-coherent because it uses
+	 * external DMA buffer located outside of IOC aperture.
+	 */
+	axs10x_mb {
+		ethernet@18000 {
+			dma-coherent;
+		};
+
+		usb@40000 {
+			dma-coherent;
+		};
+
+		usb@60000 {
+			dma-coherent;
+		};
+
+		mmc@15000 {
+			dma-coherent;
+		};
+	};
+
+	/*
+	 * The DW APB ICTL intc on MB is connected to CPU intc via a
+	 * DT "invisible" DW APB GPIO block, configured to simply pass thru
+	 * interrupts - setup accordinly in platform init (plat-axs10x/ax10x.c)
+	 *
+	 * So here we mimic a direct connection betwen them, ignoring the
+	 * ABPG GPIO. Thus set "interrupts = <24>" (DW APB GPIO to core)
+	 * instead of "interrupts = <12>" (DW APB ICTL to DW APB GPIO)
+	 *
+	 * This intc actually resides on MB, but we move it here to
+	 * avoid duplicating the MB dtsi file given that IRQ from
+	 * this intc to cpu intc are different for axs101 and axs103
+	 */
+	mb_intc: interrupt-controller@e0012000 {
+		#interrupt-cells = <1>;
+		compatible = "snps,dw-apb-ictl";
+		reg = < 0x0 0xe0012000 0x0 0x200 >;
+		interrupt-controller;
+		interrupt-parent = <&core_intc>;
+		interrupts = < 24 >;
+	};
+
+	memory {
+		device_type = "memory";
+		/* CONFIG_LINUX_RAM_BASE needs to match low mem start */
+		reg = <0x0 0x80000000 0x0 0x20000000	/* 512 MiB low mem */
+		       0x1 0xc0000000 0x0 0x40000000>;	/* 1 GiB highmem */
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+		/*
+		 * Move frame buffer out of IOC aperture (0x8z-0xaz).
+		 */
+		frame_buffer: frame_buffer@be000000 {
+			compatible = "shared-dma-pool";
+			reg = <0x0 0xbe000000 0x0 0x2000000>;
+			no-map;
+		};
+	};
+};