Adding upstream version 6.6.15.upstream/6.6.15

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

5 files changed, 897 insertions, 0 deletions

diff --git a/arch/sh/boards/mach-migor/Kconfig b/arch/sh/boards/mach-migor/Kconfig
new file mode 100644
index 0000000000..fb64a10e21
--- /dev/null
+++ b/arch/sh/boards/mach-migor/Kconfig
@@ -0,0 +1,16 @@
+# SPDX-License-Identifier: GPL-2.0
+if SH_MIGOR
+
+choice
+	prompt "Migo-R LCD Panel Board Selection"
+	default SH_MIGOR_QVGA
+
+config SH_MIGOR_QVGA
+	bool "QVGA (320x240)"
+
+config SH_MIGOR_RTA_WVGA
+	bool "RTA WVGA (800x480)"
+
+endchoice
+
+endif
diff --git a/arch/sh/boards/mach-migor/Makefile b/arch/sh/boards/mach-migor/Makefile
new file mode 100644
index 0000000000..c223d759fc
--- /dev/null
+++ b/arch/sh/boards/mach-migor/Makefile
@@ -0,0 +1,3 @@
+# SPDX-License-Identifier: GPL-2.0
+obj-y	 := setup.o sdram.o
+obj-$(CONFIG_SH_MIGOR_QVGA)	+=  lcd_qvga.o
diff --git a/arch/sh/boards/mach-migor/lcd_qvga.c b/arch/sh/boards/mach-migor/lcd_qvga.c
new file mode 100644
index 0000000000..4ebf130510
--- /dev/null
+++ b/arch/sh/boards/mach-migor/lcd_qvga.c
@@ -0,0 +1,163 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Support for SuperH MigoR Quarter VGA LCD Panel
+ *
+ * Copyright (C) 2008 Magnus Damm
+ *
+ * Based on lcd_powertip.c from Kenati Technologies Pvt Ltd.
+ * Copyright (c) 2007 Ujjwal Pande <ujjwal@kenati.com>,
+ */
+
+#include <linux/delay.h>
+#include <linux/err.h>
+#include <linux/fb.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/gpio.h>
+#include <video/sh_mobile_lcdc.h>
+#include <cpu/sh7722.h>
+#include <mach/migor.h>
+
+/* LCD Module is a PH240320T according to board schematics. This module
+ * is made up of a 240x320 LCD hooked up to a R61505U (or HX8347-A01?)
+ * Driver IC. This IC is connected to the SH7722 built-in LCDC using a
+ * SYS-80 interface configured in 16 bit mode.
+ *
+ * Index 0: "Device Code Read" returns 0x1505.
+ */
+
+static void reset_lcd_module(void)
+{
+	gpio_set_value(GPIO_PTH2, 0);
+	mdelay(2);
+	gpio_set_value(GPIO_PTH2, 1);
+	mdelay(1);
+}
+
+/* DB0-DB7 are connected to D1-D8, and DB8-DB15 to D10-D17 */
+
+static unsigned long adjust_reg18(unsigned short data)
+{
+	unsigned long tmp1, tmp2;
+
+	tmp1 = (data<<1 | 0x00000001) & 0x000001FF;
+	tmp2 = (data<<2 | 0x00000200) & 0x0003FE00;
+	return tmp1 | tmp2;
+}
+
+static void write_reg(void *sys_ops_handle,
+		       struct sh_mobile_lcdc_sys_bus_ops *sys_ops,
+		       unsigned short reg, unsigned short data)
+{
+	sys_ops->write_index(sys_ops_handle, adjust_reg18(reg << 8 | data));
+}
+
+static void write_reg16(void *sys_ops_handle,
+			struct sh_mobile_lcdc_sys_bus_ops *sys_ops,
+			unsigned short reg, unsigned short data)
+{
+	sys_ops->write_index(sys_ops_handle, adjust_reg18(reg));
+	sys_ops->write_data(sys_ops_handle, adjust_reg18(data));
+}
+
+static unsigned long read_reg16(void *sys_ops_handle,
+				struct sh_mobile_lcdc_sys_bus_ops *sys_ops,
+				unsigned short reg)
+{
+	unsigned long data;
+
+	sys_ops->write_index(sys_ops_handle, adjust_reg18(reg));
+	data = sys_ops->read_data(sys_ops_handle);
+	return ((data >> 1) & 0xff) | ((data >> 2) & 0xff00);
+}
+
+static void migor_lcd_qvga_seq(void *sys_ops_handle,
+			       struct sh_mobile_lcdc_sys_bus_ops *sys_ops,
+			       unsigned short const *data, int no_data)
+{
+	int i;
+
+	for (i = 0; i < no_data; i += 2)
+		write_reg16(sys_ops_handle, sys_ops, data[i], data[i + 1]);
+}
+
+static const unsigned short sync_data[] = {
+	0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,
+};
+
+static const unsigned short magic0_data[] = {
+	0x0060, 0x2700, 0x0008, 0x0808, 0x0090, 0x001A, 0x0007, 0x0001,
+	0x0017, 0x0001, 0x0019, 0x0000, 0x0010, 0x17B0, 0x0011, 0x0116,
+	0x0012, 0x0198, 0x0013, 0x1400, 0x0029, 0x000C, 0x0012, 0x01B8,
+};
+
+static const unsigned short magic1_data[] = {
+	0x0030, 0x0307, 0x0031, 0x0303, 0x0032, 0x0603, 0x0033, 0x0202,
+	0x0034, 0x0202, 0x0035, 0x0202, 0x0036, 0x1F1F, 0x0037, 0x0303,
+	0x0038, 0x0303, 0x0039, 0x0603, 0x003A, 0x0202, 0x003B, 0x0102,
+	0x003C, 0x0204, 0x003D, 0x0000, 0x0001, 0x0100, 0x0002, 0x0300,
+	0x0003, 0x5028, 0x0020, 0x00ef, 0x0021, 0x0000, 0x0004, 0x0000,
+	0x0009, 0x0000, 0x000A, 0x0008, 0x000C, 0x0000, 0x000D, 0x0000,
+	0x0015, 0x8000,
+};
+
+static const unsigned short magic2_data[] = {
+	0x0061, 0x0001, 0x0092, 0x0100, 0x0093, 0x0001, 0x0007, 0x0021,
+};
+
+static const unsigned short magic3_data[] = {
+	0x0010, 0x16B0, 0x0011, 0x0111, 0x0007, 0x0061,
+};
+
+int migor_lcd_qvga_setup(void *sohandle, struct sh_mobile_lcdc_sys_bus_ops *so)
+{
+	unsigned long xres = 320;
+	unsigned long yres = 240;
+	int k;
+
+	reset_lcd_module();
+	migor_lcd_qvga_seq(sohandle, so, sync_data, ARRAY_SIZE(sync_data));
+
+	if (read_reg16(sohandle, so, 0) != 0x1505)
+		return -ENODEV;
+
+	pr_info("Migo-R QVGA LCD Module detected.\n");
+
+	migor_lcd_qvga_seq(sohandle, so, sync_data, ARRAY_SIZE(sync_data));
+	write_reg16(sohandle, so, 0x00A4, 0x0001);
+	mdelay(10);
+
+	migor_lcd_qvga_seq(sohandle, so, magic0_data, ARRAY_SIZE(magic0_data));
+	mdelay(100);
+
+	migor_lcd_qvga_seq(sohandle, so, magic1_data, ARRAY_SIZE(magic1_data));
+	write_reg16(sohandle, so, 0x0050, 0xef - (yres - 1));
+	write_reg16(sohandle, so, 0x0051, 0x00ef);
+	write_reg16(sohandle, so, 0x0052, 0x0000);
+	write_reg16(sohandle, so, 0x0053, xres - 1);
+
+	migor_lcd_qvga_seq(sohandle, so, magic2_data, ARRAY_SIZE(magic2_data));
+	mdelay(10);
+
+	migor_lcd_qvga_seq(sohandle, so, magic3_data, ARRAY_SIZE(magic3_data));
+	mdelay(40);
+
+	/* clear GRAM to avoid displaying garbage */
+
+	write_reg16(sohandle, so, 0x0020, 0x0000); /* horiz addr */
+	write_reg16(sohandle, so, 0x0021, 0x0000); /* vert addr */
+
+	for (k = 0; k < (xres * 256); k++) /* yes, 256 words per line */
+		write_reg16(sohandle, so, 0x0022, 0x0000);
+
+	write_reg16(sohandle, so, 0x0020, 0x0000); /* reset horiz addr */
+	write_reg16(sohandle, so, 0x0021, 0x0000); /* reset vert addr */
+	write_reg16(sohandle, so, 0x0007, 0x0173);
+	mdelay(40);
+
+	/* enable display */
+	write_reg(sohandle, so, 0x00, 0x22);
+	mdelay(100);
+	return 0;
+}
diff --git a/arch/sh/boards/mach-migor/sdram.S b/arch/sh/boards/mach-migor/sdram.S
new file mode 100644
index 0000000000..3a6bee1270
--- /dev/null
+++ b/arch/sh/boards/mach-migor/sdram.S
@@ -0,0 +1,66 @@
+/* SPDX-License-Identifier: GPL-2.0
+ *
+ * Migo-R sdram self/auto-refresh setup code
+ *
+ *  Copyright (C) 2009 Magnus Damm
+ */
+
+#include <linux/sys.h>
+#include <linux/errno.h>
+#include <linux/linkage.h>
+#include <asm/asm-offsets.h>
+#include <asm/suspend.h>
+#include <asm/romimage-macros.h>
+
+/* code to enter and leave self-refresh. must be self-contained.
+ * this code will be copied to on-chip memory and executed from there.
+ */
+	.balign 4
+ENTRY(migor_sdram_enter_start)
+
+	/* SBSC: disable power down and put in self-refresh mode */
+	mov.l	1f, r4
+	mov.l	2f, r1
+	mov.l	@r4, r2
+	or	r1, r2
+	mov.l   3f, r3
+	and	r3, r2
+	mov.l	r2, @r4
+
+	rts
+	 nop
+
+	.balign 4
+1:	.long	0xfe400008 /* SDCR0 */
+2:	.long	0x00000400
+3:	.long	0xffff7fff
+ENTRY(migor_sdram_enter_end)
+
+	.balign 4
+ENTRY(migor_sdram_leave_start)
+
+	/* SBSC: set auto-refresh mode */
+	mov.l	1f, r4
+	mov.l	@r4, r0
+	mov.l   4f, r1
+	and	r1, r0
+	mov.l	r0, @r4
+	mov.l	6f, r4
+	mov.l	8f, r0
+	mov.l	@r4, r1
+	mov	#-1, r4
+	add	r4, r1
+	or	r1, r0
+	mov.l	7f, r1
+	mov.l	r0, @r1
+
+	rts
+	 nop
+
+	.balign 4
+1:	.long	0xfe400008 /* SDCR0 */
+4:	.long	0xfffffbff
+6:	.long   0xfe40001c /* RTCOR */
+7:	.long   0xfe400018 /* RTCNT */
+8:	.long   0xa55a0000
+ENTRY(migor_sdram_leave_end)
diff --git a/arch/sh/boards/mach-migor/setup.c b/arch/sh/boards/mach-migor/setup.c
new file mode 100644
index 0000000000..773ee767d0
--- /dev/null
+++ b/arch/sh/boards/mach-migor/setup.c
@@ -0,0 +1,649 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Renesas System Solutions Asia Pte. Ltd - Migo-R
+ *
+ * Copyright (C) 2008 Magnus Damm
+ */
+#include <linux/clkdev.h>
+#include <linux/dma-map-ops.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/interrupt.h>
+#include <linux/input.h>
+#include <linux/input/sh_keysc.h>
+#include <linux/memblock.h>
+#include <linux/mmc/host.h>
+#include <linux/mtd/physmap.h>
+#include <linux/mfd/tmio.h>
+#include <linux/mtd/platnand.h>
+#include <linux/i2c.h>
+#include <linux/regulator/fixed.h>
+#include <linux/regulator/machine.h>
+#include <linux/smc91x.h>
+#include <linux/delay.h>
+#include <linux/clk.h>
+#include <linux/gpio.h>
+#include <linux/gpio/machine.h>
+#include <linux/videodev2.h>
+#include <linux/sh_intc.h>
+#include <video/sh_mobile_lcdc.h>
+#include <media/drv-intf/renesas-ceu.h>
+#include <media/i2c/ov772x.h>
+#include <media/i2c/tw9910.h>
+#include <asm/clock.h>
+#include <asm/machvec.h>
+#include <asm/io.h>
+#include <asm/suspend.h>
+#include <mach/migor.h>
+#include <cpu/sh7722.h>
+
+/* Address     IRQ  Size  Bus  Description
+ * 0x00000000       64MB  16   NOR Flash (SP29PL256N)
+ * 0x0c000000       64MB  64   SDRAM (2xK4M563233G)
+ * 0x10000000  IRQ0       16   Ethernet (SMC91C111)
+ * 0x14000000  IRQ4       16   USB 2.0 Host Controller (M66596)
+ * 0x18000000       8GB    8   NAND Flash (K9K8G08U0A)
+ */
+
+#define CEU_BUFFER_MEMORY_SIZE		(4 << 20)
+static phys_addr_t ceu_dma_membase;
+
+static struct smc91x_platdata smc91x_info = {
+	.flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
+};
+
+static struct resource smc91x_eth_resources[] = {
+	[0] = {
+		.name   = "SMC91C111" ,
+		.start  = 0x10000300,
+		.end    = 0x1000030f,
+		.flags  = IORESOURCE_MEM,
+	},
+	[1] = {
+		.start  = evt2irq(0x600), /* IRQ0 */
+		.flags  = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHLEVEL,
+	},
+};
+
+static struct platform_device smc91x_eth_device = {
+	.name           = "smc91x",
+	.num_resources  = ARRAY_SIZE(smc91x_eth_resources),
+	.resource       = smc91x_eth_resources,
+	.dev	= {
+		.platform_data	= &smc91x_info,
+	},
+};
+
+static struct sh_keysc_info sh_keysc_info = {
+	.mode = SH_KEYSC_MODE_2, /* KEYOUT0->4, KEYIN1->5 */
+	.scan_timing = 3,
+	.delay = 5,
+	.keycodes = {
+		0, KEY_UP, KEY_DOWN, KEY_LEFT, KEY_RIGHT, KEY_ENTER,
+		0, KEY_F, KEY_C, KEY_D,	KEY_H, KEY_1,
+		0, KEY_2, KEY_3, KEY_4,	KEY_5, KEY_6,
+		0, KEY_7, KEY_8, KEY_9, KEY_S, KEY_0,
+		0, KEY_P, KEY_STOP, KEY_REWIND, KEY_PLAY, KEY_FASTFORWARD,
+	},
+};
+
+static struct resource sh_keysc_resources[] = {
+	[0] = {
+		.start  = 0x044b0000,
+		.end    = 0x044b000f,
+		.flags  = IORESOURCE_MEM,
+	},
+	[1] = {
+		.start  = evt2irq(0xbe0),
+		.flags  = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device sh_keysc_device = {
+	.name           = "sh_keysc",
+	.id             = 0, /* "keysc0" clock */
+	.num_resources  = ARRAY_SIZE(sh_keysc_resources),
+	.resource       = sh_keysc_resources,
+	.dev	= {
+		.platform_data	= &sh_keysc_info,
+	},
+};
+
+static struct mtd_partition migor_nor_flash_partitions[] =
+{
+	{
+		.name = "uboot",
+		.offset = 0,
+		.size = (1 * 1024 * 1024),
+		.mask_flags = MTD_WRITEABLE,	/* Read-only */
+	},
+	{
+		.name = "rootfs",
+		.offset = MTDPART_OFS_APPEND,
+		.size = (15 * 1024 * 1024),
+	},
+	{
+		.name = "other",
+		.offset = MTDPART_OFS_APPEND,
+		.size = MTDPART_SIZ_FULL,
+	},
+};
+
+static struct physmap_flash_data migor_nor_flash_data = {
+	.width		= 2,
+	.parts		= migor_nor_flash_partitions,
+	.nr_parts	= ARRAY_SIZE(migor_nor_flash_partitions),
+};
+
+static struct resource migor_nor_flash_resources[] = {
+	[0] = {
+		.name		= "NOR Flash",
+		.start		= 0x00000000,
+		.end		= 0x03ffffff,
+		.flags		= IORESOURCE_MEM,
+	}
+};
+
+static struct platform_device migor_nor_flash_device = {
+	.name		= "physmap-flash",
+	.resource	= migor_nor_flash_resources,
+	.num_resources	= ARRAY_SIZE(migor_nor_flash_resources),
+	.dev		= {
+		.platform_data = &migor_nor_flash_data,
+	},
+};
+
+static struct mtd_partition migor_nand_flash_partitions[] = {
+	{
+		.name		= "nanddata1",
+		.offset		= 0x0,
+		.size		= 512 * 1024 * 1024,
+	},
+	{
+		.name		= "nanddata2",
+		.offset		= MTDPART_OFS_APPEND,
+		.size		= 512 * 1024 * 1024,
+	},
+};
+
+static void migor_nand_flash_cmd_ctl(struct nand_chip *chip, int cmd,
+				     unsigned int ctrl)
+{
+	if (cmd == NAND_CMD_NONE)
+		return;
+
+	if (ctrl & NAND_CLE)
+		writeb(cmd, chip->legacy.IO_ADDR_W + 0x00400000);
+	else if (ctrl & NAND_ALE)
+		writeb(cmd, chip->legacy.IO_ADDR_W + 0x00800000);
+	else
+		writeb(cmd, chip->legacy.IO_ADDR_W);
+}
+
+static int migor_nand_flash_ready(struct nand_chip *chip)
+{
+	return gpio_get_value(GPIO_PTA1); /* NAND_RBn */
+}
+
+static struct platform_nand_data migor_nand_flash_data = {
+	.chip = {
+		.nr_chips = 1,
+		.partitions = migor_nand_flash_partitions,
+		.nr_partitions = ARRAY_SIZE(migor_nand_flash_partitions),
+		.chip_delay = 20,
+	},
+	.ctrl = {
+		.dev_ready = migor_nand_flash_ready,
+		.cmd_ctrl = migor_nand_flash_cmd_ctl,
+	},
+};
+
+static struct resource migor_nand_flash_resources[] = {
+	[0] = {
+		.name		= "NAND Flash",
+		.start		= 0x18000000,
+		.end		= 0x18ffffff,
+		.flags		= IORESOURCE_MEM,
+	},
+};
+
+static struct platform_device migor_nand_flash_device = {
+	.name		= "gen_nand",
+	.resource	= migor_nand_flash_resources,
+	.num_resources	= ARRAY_SIZE(migor_nand_flash_resources),
+	.dev		= {
+		.platform_data = &migor_nand_flash_data,
+	}
+};
+
+static const struct fb_videomode migor_lcd_modes[] = {
+	{
+#if defined(CONFIG_SH_MIGOR_RTA_WVGA)
+		.name = "LB070WV1",
+		.xres = 800,
+		.yres = 480,
+		.left_margin = 64,
+		.right_margin = 16,
+		.hsync_len = 120,
+		.sync = 0,
+#elif defined(CONFIG_SH_MIGOR_QVGA)
+		.name = "PH240320T",
+		.xres = 320,
+		.yres = 240,
+		.left_margin = 0,
+		.right_margin = 16,
+		.hsync_len = 8,
+		.sync = FB_SYNC_HOR_HIGH_ACT,
+#endif
+		.upper_margin = 1,
+		.lower_margin = 17,
+		.vsync_len = 2,
+	},
+};
+
+static struct sh_mobile_lcdc_info sh_mobile_lcdc_info = {
+#if defined(CONFIG_SH_MIGOR_RTA_WVGA)
+	.clock_source = LCDC_CLK_BUS,
+	.ch[0] = {
+		.chan = LCDC_CHAN_MAINLCD,
+		.fourcc = V4L2_PIX_FMT_RGB565,
+		.interface_type = RGB16,
+		.clock_divider = 2,
+		.lcd_modes = migor_lcd_modes,
+		.num_modes = ARRAY_SIZE(migor_lcd_modes),
+		.panel_cfg = { /* 7.0 inch */
+			.width = 152,
+			.height = 91,
+		},
+	}
+#elif defined(CONFIG_SH_MIGOR_QVGA)
+	.clock_source = LCDC_CLK_PERIPHERAL,
+	.ch[0] = {
+		.chan = LCDC_CHAN_MAINLCD,
+		.fourcc = V4L2_PIX_FMT_RGB565,
+		.interface_type = SYS16A,
+		.clock_divider = 10,
+		.lcd_modes = migor_lcd_modes,
+		.num_modes = ARRAY_SIZE(migor_lcd_modes),
+		.panel_cfg = {
+			.width = 49,	/* 2.4 inch */
+			.height = 37,
+			.setup_sys = migor_lcd_qvga_setup,
+		},
+		.sys_bus_cfg = {
+			.ldmt2r = 0x06000a09,
+			.ldmt3r = 0x180e3418,
+			/* set 1s delay to encourage fsync() */
+			.deferred_io_msec = 1000,
+		},
+	}
+#endif
+};
+
+static struct resource migor_lcdc_resources[] = {
+	[0] = {
+		.name	= "LCDC",
+		.start	= 0xfe940000, /* P4-only space */
+		.end	= 0xfe942fff,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= evt2irq(0x580),
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device migor_lcdc_device = {
+	.name		= "sh_mobile_lcdc_fb",
+	.num_resources	= ARRAY_SIZE(migor_lcdc_resources),
+	.resource	= migor_lcdc_resources,
+	.dev	= {
+		.platform_data	= &sh_mobile_lcdc_info,
+	},
+};
+
+static struct ceu_platform_data ceu_pdata = {
+	.num_subdevs			= 2,
+	.subdevs = {
+		{ /* [0] = ov772x */
+			.flags		= 0,
+			.bus_width	= 8,
+			.bus_shift	= 0,
+			.i2c_adapter_id	= 0,
+			.i2c_address	= 0x21,
+		},
+		{ /* [1] = tw9910 */
+			.flags		= 0,
+			.bus_width	= 8,
+			.bus_shift	= 0,
+			.i2c_adapter_id	= 0,
+			.i2c_address	= 0x45,
+		},
+	},
+};
+
+static struct resource migor_ceu_resources[] = {
+	[0] = {
+		.name	= "CEU",
+		.start	= 0xfe910000,
+		.end	= 0xfe91009f,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start  = evt2irq(0x880),
+		.flags  = IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device migor_ceu_device = {
+	.name		= "renesas-ceu",
+	.id             = 0, /* ceu.0 */
+	.num_resources	= ARRAY_SIZE(migor_ceu_resources),
+	.resource	= migor_ceu_resources,
+	.dev	= {
+		.platform_data	= &ceu_pdata,
+	},
+};
+
+/* Powerdown/reset gpios for CEU image sensors */
+static struct gpiod_lookup_table ov7725_gpios = {
+	.dev_id		= "0-0021",
+	.table		= {
+		GPIO_LOOKUP("sh7722_pfc", GPIO_PTT0, "powerdown",
+			    GPIO_ACTIVE_HIGH),
+		GPIO_LOOKUP("sh7722_pfc", GPIO_PTT3, "reset", GPIO_ACTIVE_LOW),
+	},
+};
+
+static struct gpiod_lookup_table tw9910_gpios = {
+	.dev_id		= "0-0045",
+	.table		= {
+		GPIO_LOOKUP("sh7722_pfc", GPIO_PTT2, "pdn", GPIO_ACTIVE_LOW),
+		GPIO_LOOKUP("sh7722_pfc", GPIO_PTT3, "rstb", GPIO_ACTIVE_LOW),
+	},
+};
+
+/* Fixed 3.3V regulator to be used by SDHI0 */
+static struct regulator_consumer_supply fixed3v3_power_consumers[] =
+{
+	REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.0"),
+	REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.0"),
+};
+
+static struct resource sdhi_cn9_resources[] = {
+	[0] = {
+		.name	= "SDHI",
+		.start	= 0x04ce0000,
+		.end	= 0x04ce00ff,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= evt2irq(0xe80),
+		.flags  = IORESOURCE_IRQ,
+	},
+};
+
+static struct tmio_mmc_data sh7724_sdhi_data = {
+	.chan_priv_tx	= (void *)SHDMA_SLAVE_SDHI0_TX,
+	.chan_priv_rx	= (void *)SHDMA_SLAVE_SDHI0_RX,
+	.capabilities	= MMC_CAP_SDIO_IRQ,
+};
+
+static struct platform_device sdhi_cn9_device = {
+	.name		= "sh_mobile_sdhi",
+	.num_resources	= ARRAY_SIZE(sdhi_cn9_resources),
+	.resource	= sdhi_cn9_resources,
+	.dev = {
+		.platform_data	= &sh7724_sdhi_data,
+	},
+};
+
+static struct ov772x_camera_info ov7725_info = {
+	.flags		= 0,
+};
+
+static struct tw9910_video_info tw9910_info = {
+	.buswidth       = 8,
+	.mpout          = TW9910_MPO_FIELD,
+};
+
+static struct i2c_board_info migor_i2c_devices[] = {
+	{
+		I2C_BOARD_INFO("rs5c372b", 0x32),
+	},
+	{
+		I2C_BOARD_INFO("migor_ts", 0x51),
+		.irq = evt2irq(0x6c0), /* IRQ6 */
+	},
+	{
+		I2C_BOARD_INFO("wm8978", 0x1a),
+	},
+	{
+		I2C_BOARD_INFO("ov772x", 0x21),
+		.platform_data = &ov7725_info,
+	},
+	{
+		I2C_BOARD_INFO("tw9910", 0x45),
+		.platform_data = &tw9910_info,
+	},
+};
+
+static struct platform_device *migor_devices[] __initdata = {
+	&smc91x_eth_device,
+	&sh_keysc_device,
+	&migor_lcdc_device,
+	&migor_nor_flash_device,
+	&migor_nand_flash_device,
+	&sdhi_cn9_device,
+};
+
+extern char migor_sdram_enter_start;
+extern char migor_sdram_enter_end;
+extern char migor_sdram_leave_start;
+extern char migor_sdram_leave_end;
+
+static int __init migor_devices_setup(void)
+{
+	struct clk *video_clk;
+
+	/* register board specific self-refresh code */
+	sh_mobile_register_self_refresh(SUSP_SH_STANDBY | SUSP_SH_SF,
+					&migor_sdram_enter_start,
+					&migor_sdram_enter_end,
+					&migor_sdram_leave_start,
+					&migor_sdram_leave_end);
+
+	regulator_register_always_on(0, "fixed-3.3V", fixed3v3_power_consumers,
+				     ARRAY_SIZE(fixed3v3_power_consumers), 3300000);
+
+	/* Let D11 LED show STATUS0 */
+	gpio_request(GPIO_FN_STATUS0, NULL);
+
+	/* Lit D12 LED show PDSTATUS */
+	gpio_request(GPIO_FN_PDSTATUS, NULL);
+
+	/* SMC91C111 - Enable IRQ0, Setup CS4 for 16-bit fast access */
+	gpio_request(GPIO_FN_IRQ0, NULL);
+	__raw_writel(0x00003400, BSC_CS4BCR);
+	__raw_writel(0x00110080, BSC_CS4WCR);
+
+	/* KEYSC */
+	gpio_request(GPIO_FN_KEYOUT0, NULL);
+	gpio_request(GPIO_FN_KEYOUT1, NULL);
+	gpio_request(GPIO_FN_KEYOUT2, NULL);
+	gpio_request(GPIO_FN_KEYOUT3, NULL);
+	gpio_request(GPIO_FN_KEYOUT4_IN6, NULL);
+	gpio_request(GPIO_FN_KEYIN1, NULL);
+	gpio_request(GPIO_FN_KEYIN2, NULL);
+	gpio_request(GPIO_FN_KEYIN3, NULL);
+	gpio_request(GPIO_FN_KEYIN4, NULL);
+	gpio_request(GPIO_FN_KEYOUT5_IN5, NULL);
+
+	/* NAND Flash */
+	gpio_request(GPIO_FN_CS6A_CE2B, NULL);
+	__raw_writel((__raw_readl(BSC_CS6ABCR) & ~0x0600) | 0x0200, BSC_CS6ABCR);
+	gpio_request(GPIO_PTA1, NULL);
+	gpio_direction_input(GPIO_PTA1);
+
+	/* SDHI */
+	gpio_request(GPIO_FN_SDHICD, NULL);
+	gpio_request(GPIO_FN_SDHIWP, NULL);
+	gpio_request(GPIO_FN_SDHID3, NULL);
+	gpio_request(GPIO_FN_SDHID2, NULL);
+	gpio_request(GPIO_FN_SDHID1, NULL);
+	gpio_request(GPIO_FN_SDHID0, NULL);
+	gpio_request(GPIO_FN_SDHICMD, NULL);
+	gpio_request(GPIO_FN_SDHICLK, NULL);
+
+	/* Touch Panel */
+	gpio_request(GPIO_FN_IRQ6, NULL);
+
+	/* LCD Panel */
+#ifdef CONFIG_SH_MIGOR_QVGA /* LCDC - QVGA - Enable SYS Interface signals */
+	gpio_request(GPIO_FN_LCDD17, NULL);
+	gpio_request(GPIO_FN_LCDD16, NULL);
+	gpio_request(GPIO_FN_LCDD15, NULL);
+	gpio_request(GPIO_FN_LCDD14, NULL);
+	gpio_request(GPIO_FN_LCDD13, NULL);
+	gpio_request(GPIO_FN_LCDD12, NULL);
+	gpio_request(GPIO_FN_LCDD11, NULL);
+	gpio_request(GPIO_FN_LCDD10, NULL);
+	gpio_request(GPIO_FN_LCDD8, NULL);
+	gpio_request(GPIO_FN_LCDD7, NULL);
+	gpio_request(GPIO_FN_LCDD6, NULL);
+	gpio_request(GPIO_FN_LCDD5, NULL);
+	gpio_request(GPIO_FN_LCDD4, NULL);
+	gpio_request(GPIO_FN_LCDD3, NULL);
+	gpio_request(GPIO_FN_LCDD2, NULL);
+	gpio_request(GPIO_FN_LCDD1, NULL);
+	gpio_request(GPIO_FN_LCDRS, NULL);
+	gpio_request(GPIO_FN_LCDCS, NULL);
+	gpio_request(GPIO_FN_LCDRD, NULL);
+	gpio_request(GPIO_FN_LCDWR, NULL);
+	gpio_request(GPIO_PTH2, NULL); /* LCD_DON */
+	gpio_direction_output(GPIO_PTH2, 1);
+#endif
+#ifdef CONFIG_SH_MIGOR_RTA_WVGA /* LCDC - WVGA - Enable RGB Interface signals */
+	gpio_request(GPIO_FN_LCDD15, NULL);
+	gpio_request(GPIO_FN_LCDD14, NULL);
+	gpio_request(GPIO_FN_LCDD13, NULL);
+	gpio_request(GPIO_FN_LCDD12, NULL);
+	gpio_request(GPIO_FN_LCDD11, NULL);
+	gpio_request(GPIO_FN_LCDD10, NULL);
+	gpio_request(GPIO_FN_LCDD9, NULL);
+	gpio_request(GPIO_FN_LCDD8, NULL);
+	gpio_request(GPIO_FN_LCDD7, NULL);
+	gpio_request(GPIO_FN_LCDD6, NULL);
+	gpio_request(GPIO_FN_LCDD5, NULL);
+	gpio_request(GPIO_FN_LCDD4, NULL);
+	gpio_request(GPIO_FN_LCDD3, NULL);
+	gpio_request(GPIO_FN_LCDD2, NULL);
+	gpio_request(GPIO_FN_LCDD1, NULL);
+	gpio_request(GPIO_FN_LCDD0, NULL);
+	gpio_request(GPIO_FN_LCDLCLK, NULL);
+	gpio_request(GPIO_FN_LCDDCK, NULL);
+	gpio_request(GPIO_FN_LCDVEPWC, NULL);
+	gpio_request(GPIO_FN_LCDVCPWC, NULL);
+	gpio_request(GPIO_FN_LCDVSYN, NULL);
+	gpio_request(GPIO_FN_LCDHSYN, NULL);
+	gpio_request(GPIO_FN_LCDDISP, NULL);
+	gpio_request(GPIO_FN_LCDDON, NULL);
+#endif
+
+	/* CEU */
+	gpio_request(GPIO_FN_VIO_CLK2, NULL);
+	gpio_request(GPIO_FN_VIO_VD2, NULL);
+	gpio_request(GPIO_FN_VIO_HD2, NULL);
+	gpio_request(GPIO_FN_VIO_FLD, NULL);
+	gpio_request(GPIO_FN_VIO_CKO, NULL);
+	gpio_request(GPIO_FN_VIO_D15, NULL);
+	gpio_request(GPIO_FN_VIO_D14, NULL);
+	gpio_request(GPIO_FN_VIO_D13, NULL);
+	gpio_request(GPIO_FN_VIO_D12, NULL);
+	gpio_request(GPIO_FN_VIO_D11, NULL);
+	gpio_request(GPIO_FN_VIO_D10, NULL);
+	gpio_request(GPIO_FN_VIO_D9, NULL);
+	gpio_request(GPIO_FN_VIO_D8, NULL);
+
+	__raw_writew(__raw_readw(PORT_MSELCRB) | 0x2000, PORT_MSELCRB); /* D15->D8 */
+
+	/* SIU: Port B */
+	gpio_request(GPIO_FN_SIUBOLR, NULL);
+	gpio_request(GPIO_FN_SIUBOBT, NULL);
+	gpio_request(GPIO_FN_SIUBISLD, NULL);
+	gpio_request(GPIO_FN_SIUBOSLD, NULL);
+	gpio_request(GPIO_FN_SIUMCKB, NULL);
+
+	/*
+	 * The original driver sets SIUB OLR/OBT, ILR/IBT, and SIUA OLR/OBT to
+	 * output. Need only SIUB, set to output for master mode (table 34.2)
+	 */
+	__raw_writew(__raw_readw(PORT_MSELCRA) | 1, PORT_MSELCRA);
+
+	 /*
+	  * Use 10 MHz VIO_CKO instead of 24 MHz to work around signal quality
+	  * issues on Panel Board V2.1.
+	  */
+	video_clk = clk_get(NULL, "video_clk");
+	if (!IS_ERR(video_clk)) {
+		clk_set_rate(video_clk, clk_round_rate(video_clk, 10000000));
+		clk_put(video_clk);
+	}
+
+	/* Add a clock alias for ov7725 xclk source. */
+	clk_add_alias(NULL, "0-0021", "video_clk", NULL);
+
+	/* Register GPIOs for video sources. */
+	gpiod_add_lookup_table(&ov7725_gpios);
+	gpiod_add_lookup_table(&tw9910_gpios);
+
+	i2c_register_board_info(0, migor_i2c_devices,
+				ARRAY_SIZE(migor_i2c_devices));
+
+	/* Initialize CEU platform device separately to map memory first */
+	device_initialize(&migor_ceu_device.dev);
+	dma_declare_coherent_memory(&migor_ceu_device.dev,
+			ceu_dma_membase, ceu_dma_membase,
+			CEU_BUFFER_MEMORY_SIZE);
+
+	platform_device_add(&migor_ceu_device);
+
+	return platform_add_devices(migor_devices, ARRAY_SIZE(migor_devices));
+}
+arch_initcall(migor_devices_setup);
+
+/* Return the board specific boot mode pin configuration */
+static int migor_mode_pins(void)
+{
+	/* MD0=1, MD1=1, MD2=0: Clock Mode 3
+	 * MD3=0: 16-bit Area0 Bus Width
+	 * MD5=1: Little Endian
+	 * TSTMD=1, MD8=0: Test Mode Disabled
+	 */
+	return MODE_PIN0 | MODE_PIN1 | MODE_PIN5;
+}
+
+/* Reserve a portion of memory for CEU buffers */
+static void __init migor_mv_mem_reserve(void)
+{
+	phys_addr_t phys;
+	phys_addr_t size = CEU_BUFFER_MEMORY_SIZE;
+
+	phys = memblock_phys_alloc(size, PAGE_SIZE);
+	if (!phys)
+		panic("Failed to allocate CEU memory\n");
+
+	memblock_phys_free(phys, size);
+	memblock_remove(phys, size);
+
+	ceu_dma_membase = phys;
+}
+
+/*
+ * The Machine Vector
+ */
+static struct sh_machine_vector mv_migor __initmv = {
+	.mv_name		= "Migo-R",
+	.mv_mode_pins		= migor_mode_pins,
+	.mv_mem_reserve		= migor_mv_mem_reserve,
+};