Adding upstream version 6.6.15.upstream/6.6.15

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 696 insertions, 0 deletions

diff --git a/drivers/bus/hisi_lpc.c b/drivers/bus/hisi_lpc.c
new file mode 100644
index 0000000000..cdc4e38c11
--- /dev/null
+++ b/drivers/bus/hisi_lpc.c
@@ -0,0 +1,696 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2017 Hisilicon Limited, All Rights Reserved.
+ * Author: Zhichang Yuan <yuanzhichang@hisilicon.com>
+ * Author: Zou Rongrong <zourongrong@huawei.com>
+ * Author: John Garry <john.garry@huawei.com>
+ */
+
+#include <linux/acpi.h>
+#include <linux/console.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/logic_pio.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/pci.h>
+#include <linux/platform_device.h>
+#include <linux/serial_8250.h>
+#include <linux/slab.h>
+
+#define DRV_NAME "hisi-lpc"
+
+/*
+ * Setting this bit means each IO operation will target a different port
+ * address; 0 means repeated IO operations will use the same port,
+ * such as BT.
+ */
+#define FG_INCRADDR_LPC		0x02
+
+struct lpc_cycle_para {
+	unsigned int opflags;
+	unsigned int csize; /* data length of each operation */
+};
+
+struct hisi_lpc_dev {
+	spinlock_t cycle_lock;
+	void __iomem  *membase;
+	struct logic_pio_hwaddr *io_host;
+};
+
+/* The max IO cycle counts supported is four per operation at maximum */
+#define LPC_MAX_DWIDTH	4
+
+#define LPC_REG_STARTUP_SIGNAL		0x00
+#define LPC_REG_STARTUP_SIGNAL_START	BIT(0)
+#define LPC_REG_OP_STATUS		0x04
+#define LPC_REG_OP_STATUS_IDLE		BIT(0)
+#define LPC_REG_OP_STATUS_FINISHED	BIT(1)
+#define LPC_REG_OP_LEN			0x10 /* LPC cycles count per start */
+#define LPC_REG_CMD			0x14
+#define LPC_REG_CMD_OP			BIT(0) /* 0: read, 1: write */
+#define LPC_REG_CMD_SAMEADDR		BIT(3)
+#define LPC_REG_ADDR			0x20 /* target address */
+#define LPC_REG_WDATA			0x24 /* write FIFO */
+#define LPC_REG_RDATA			0x28 /* read FIFO */
+
+/* The minimal nanosecond interval for each query on LPC cycle status */
+#define LPC_NSEC_PERWAIT	100
+
+/*
+ * The maximum waiting time is about 128us.  It is specific for stream I/O,
+ * such as ins.
+ *
+ * The fastest IO cycle time is about 390ns, but the worst case will wait
+ * for extra 256 lpc clocks, so (256 + 13) * 30ns = 8 us. The maximum burst
+ * cycles is 16. So, the maximum waiting time is about 128us under worst
+ * case.
+ *
+ * Choose 1300 as the maximum.
+ */
+#define LPC_MAX_WAITCNT		1300
+
+/* About 10us. This is specific for single IO operations, such as inb */
+#define LPC_PEROP_WAITCNT	100
+
+static int wait_lpc_idle(void __iomem *mbase, unsigned int waitcnt)
+{
+	u32 status;
+
+	do {
+		status = readl(mbase + LPC_REG_OP_STATUS);
+		if (status & LPC_REG_OP_STATUS_IDLE)
+			return (status & LPC_REG_OP_STATUS_FINISHED) ? 0 : -EIO;
+		ndelay(LPC_NSEC_PERWAIT);
+	} while (--waitcnt);
+
+	return -ETIMEDOUT;
+}
+
+/*
+ * hisi_lpc_target_in - trigger a series of LPC cycles for read operation
+ * @lpcdev: pointer to hisi lpc device
+ * @para: some parameters used to control the lpc I/O operations
+ * @addr: the lpc I/O target port address
+ * @buf: where the read back data is stored
+ * @opcnt: how many I/O operations required, i.e. data width
+ *
+ * Returns 0 on success, non-zero on fail.
+ */
+static int hisi_lpc_target_in(struct hisi_lpc_dev *lpcdev,
+			      struct lpc_cycle_para *para, unsigned long addr,
+			      unsigned char *buf, unsigned long opcnt)
+{
+	unsigned int cmd_word;
+	unsigned int waitcnt;
+	unsigned long flags;
+	int ret;
+
+	if (!buf || !opcnt || !para || !para->csize || !lpcdev)
+		return -EINVAL;
+
+	cmd_word = 0; /* IO mode, Read */
+	waitcnt = LPC_PEROP_WAITCNT;
+	if (!(para->opflags & FG_INCRADDR_LPC)) {
+		cmd_word |= LPC_REG_CMD_SAMEADDR;
+		waitcnt = LPC_MAX_WAITCNT;
+	}
+
+	/* whole operation must be atomic */
+	spin_lock_irqsave(&lpcdev->cycle_lock, flags);
+
+	writel_relaxed(opcnt, lpcdev->membase + LPC_REG_OP_LEN);
+	writel_relaxed(cmd_word, lpcdev->membase + LPC_REG_CMD);
+	writel_relaxed(addr, lpcdev->membase + LPC_REG_ADDR);
+
+	writel(LPC_REG_STARTUP_SIGNAL_START,
+	       lpcdev->membase + LPC_REG_STARTUP_SIGNAL);
+
+	/* whether the operation is finished */
+	ret = wait_lpc_idle(lpcdev->membase, waitcnt);
+	if (ret) {
+		spin_unlock_irqrestore(&lpcdev->cycle_lock, flags);
+		return ret;
+	}
+
+	readsb(lpcdev->membase + LPC_REG_RDATA, buf, opcnt);
+
+	spin_unlock_irqrestore(&lpcdev->cycle_lock, flags);
+
+	return 0;
+}
+
+/*
+ * hisi_lpc_target_out - trigger a series of LPC cycles for write operation
+ * @lpcdev: pointer to hisi lpc device
+ * @para: some parameters used to control the lpc I/O operations
+ * @addr: the lpc I/O target port address
+ * @buf: where the data to be written is stored
+ * @opcnt: how many I/O operations required, i.e. data width
+ *
+ * Returns 0 on success, non-zero on fail.
+ */
+static int hisi_lpc_target_out(struct hisi_lpc_dev *lpcdev,
+			       struct lpc_cycle_para *para, unsigned long addr,
+			       const unsigned char *buf, unsigned long opcnt)
+{
+	unsigned int waitcnt;
+	unsigned long flags;
+	u32 cmd_word;
+	int ret;
+
+	if (!buf || !opcnt || !para || !lpcdev)
+		return -EINVAL;
+
+	/* default is increasing address */
+	cmd_word = LPC_REG_CMD_OP; /* IO mode, write */
+	waitcnt = LPC_PEROP_WAITCNT;
+	if (!(para->opflags & FG_INCRADDR_LPC)) {
+		cmd_word |= LPC_REG_CMD_SAMEADDR;
+		waitcnt = LPC_MAX_WAITCNT;
+	}
+
+	spin_lock_irqsave(&lpcdev->cycle_lock, flags);
+
+	writel_relaxed(opcnt, lpcdev->membase + LPC_REG_OP_LEN);
+	writel_relaxed(cmd_word, lpcdev->membase + LPC_REG_CMD);
+	writel_relaxed(addr, lpcdev->membase + LPC_REG_ADDR);
+
+	writesb(lpcdev->membase + LPC_REG_WDATA, buf, opcnt);
+
+	writel(LPC_REG_STARTUP_SIGNAL_START,
+	       lpcdev->membase + LPC_REG_STARTUP_SIGNAL);
+
+	/* whether the operation is finished */
+	ret = wait_lpc_idle(lpcdev->membase, waitcnt);
+
+	spin_unlock_irqrestore(&lpcdev->cycle_lock, flags);
+
+	return ret;
+}
+
+static unsigned long hisi_lpc_pio_to_addr(struct hisi_lpc_dev *lpcdev,
+					  unsigned long pio)
+{
+	return pio - lpcdev->io_host->io_start + lpcdev->io_host->hw_start;
+}
+
+/*
+ * hisi_lpc_comm_in - input the data in a single operation
+ * @hostdata: pointer to the device information relevant to LPC controller
+ * @pio: the target I/O port address
+ * @dwidth: the data length required to read from the target I/O port
+ *
+ * When success, data is returned. Otherwise, ~0 is returned.
+ */
+static u32 hisi_lpc_comm_in(void *hostdata, unsigned long pio, size_t dwidth)
+{
+	struct hisi_lpc_dev *lpcdev = hostdata;
+	struct lpc_cycle_para iopara;
+	unsigned long addr;
+	__le32 rd_data = 0;
+	int ret;
+
+	if (!lpcdev || !dwidth || dwidth > LPC_MAX_DWIDTH)
+		return ~0;
+
+	addr = hisi_lpc_pio_to_addr(lpcdev, pio);
+
+	iopara.opflags = FG_INCRADDR_LPC;
+	iopara.csize = dwidth;
+
+	ret = hisi_lpc_target_in(lpcdev, &iopara, addr,
+				 (unsigned char *)&rd_data, dwidth);
+	if (ret)
+		return ~0;
+
+	return le32_to_cpu(rd_data);
+}
+
+/*
+ * hisi_lpc_comm_out - output the data in a single operation
+ * @hostdata: pointer to the device information relevant to LPC controller
+ * @pio: the target I/O port address
+ * @val: a value to be output from caller, maximum is four bytes
+ * @dwidth: the data width required writing to the target I/O port
+ *
+ * This function corresponds to out(b,w,l) only.
+ */
+static void hisi_lpc_comm_out(void *hostdata, unsigned long pio,
+			      u32 val, size_t dwidth)
+{
+	struct hisi_lpc_dev *lpcdev = hostdata;
+	struct lpc_cycle_para iopara;
+	const unsigned char *buf;
+	unsigned long addr;
+	__le32 _val = cpu_to_le32(val);
+
+	if (!lpcdev || !dwidth || dwidth > LPC_MAX_DWIDTH)
+		return;
+
+	buf = (const unsigned char *)&_val;
+	addr = hisi_lpc_pio_to_addr(lpcdev, pio);
+
+	iopara.opflags = FG_INCRADDR_LPC;
+	iopara.csize = dwidth;
+
+	hisi_lpc_target_out(lpcdev, &iopara, addr, buf, dwidth);
+}
+
+/*
+ * hisi_lpc_comm_ins - input the data in the buffer in multiple operations
+ * @hostdata: pointer to the device information relevant to LPC controller
+ * @pio: the target I/O port address
+ * @buffer: a buffer where read/input data bytes are stored
+ * @dwidth: the data width required writing to the target I/O port
+ * @count: how many data units whose length is dwidth will be read
+ *
+ * When success, the data read back is stored in buffer pointed by buffer.
+ * Returns 0 on success, -errno otherwise.
+ */
+static u32 hisi_lpc_comm_ins(void *hostdata, unsigned long pio, void *buffer,
+			     size_t dwidth, unsigned int count)
+{
+	struct hisi_lpc_dev *lpcdev = hostdata;
+	unsigned char *buf = buffer;
+	struct lpc_cycle_para iopara;
+	unsigned long addr;
+
+	if (!lpcdev || !buf || !count || !dwidth || dwidth > LPC_MAX_DWIDTH)
+		return -EINVAL;
+
+	iopara.opflags = 0;
+	if (dwidth > 1)
+		iopara.opflags |= FG_INCRADDR_LPC;
+	iopara.csize = dwidth;
+
+	addr = hisi_lpc_pio_to_addr(lpcdev, pio);
+
+	do {
+		int ret;
+
+		ret = hisi_lpc_target_in(lpcdev, &iopara, addr, buf, dwidth);
+		if (ret)
+			return ret;
+		buf += dwidth;
+	} while (--count);
+
+	return 0;
+}
+
+/*
+ * hisi_lpc_comm_outs - output the data in the buffer in multiple operations
+ * @hostdata: pointer to the device information relevant to LPC controller
+ * @pio: the target I/O port address
+ * @buffer: a buffer where write/output data bytes are stored
+ * @dwidth: the data width required writing to the target I/O port
+ * @count: how many data units whose length is dwidth will be written
+ */
+static void hisi_lpc_comm_outs(void *hostdata, unsigned long pio,
+			       const void *buffer, size_t dwidth,
+			       unsigned int count)
+{
+	struct hisi_lpc_dev *lpcdev = hostdata;
+	struct lpc_cycle_para iopara;
+	const unsigned char *buf = buffer;
+	unsigned long addr;
+
+	if (!lpcdev || !buf || !count || !dwidth || dwidth > LPC_MAX_DWIDTH)
+		return;
+
+	iopara.opflags = 0;
+	if (dwidth > 1)
+		iopara.opflags |= FG_INCRADDR_LPC;
+	iopara.csize = dwidth;
+
+	addr = hisi_lpc_pio_to_addr(lpcdev, pio);
+	do {
+		if (hisi_lpc_target_out(lpcdev, &iopara, addr, buf, dwidth))
+			break;
+		buf += dwidth;
+	} while (--count);
+}
+
+static const struct logic_pio_host_ops hisi_lpc_ops = {
+	.in = hisi_lpc_comm_in,
+	.out = hisi_lpc_comm_out,
+	.ins = hisi_lpc_comm_ins,
+	.outs = hisi_lpc_comm_outs,
+};
+
+#ifdef CONFIG_ACPI
+static int hisi_lpc_acpi_xlat_io_res(struct acpi_device *adev,
+				     struct acpi_device *host,
+				     struct resource *res)
+{
+	unsigned long sys_port;
+	resource_size_t len = resource_size(res);
+
+	sys_port = logic_pio_trans_hwaddr(acpi_fwnode_handle(host), res->start, len);
+	if (sys_port == ~0UL)
+		return -EFAULT;
+
+	res->start = sys_port;
+	res->end = sys_port + len;
+
+	return 0;
+}
+
+/*
+ * Released firmware describes the IO port max address as 0x3fff, which is
+ * the max host bus address. Fixup to a proper range. This will probably
+ * never be fixed in firmware.
+ */
+static void hisi_lpc_acpi_fixup_child_resource(struct device *hostdev,
+					       struct resource *r)
+{
+	if (r->end != 0x3fff)
+		return;
+
+	if (r->start == 0xe4)
+		r->end = 0xe4 + 0x04 - 1;
+	else if (r->start == 0x2f8)
+		r->end = 0x2f8 + 0x08 - 1;
+	else
+		dev_warn(hostdev, "unrecognised resource %pR to fixup, ignoring\n",
+			 r);
+}
+
+/*
+ * hisi_lpc_acpi_set_io_res - set the resources for a child
+ * @adev: ACPI companion of the device node to be updated the I/O resource
+ * @hostdev: the device node associated with host controller
+ * @res: double pointer to be set to the address of translated resources
+ * @num_res: pointer to variable to hold the number of translated resources
+ *
+ * Returns 0 when successful, and a negative value for failure.
+ *
+ * For a given host controller, each child device will have an associated
+ * host-relative address resource.  This function will return the translated
+ * logical PIO addresses for each child devices resources.
+ */
+static int hisi_lpc_acpi_set_io_res(struct acpi_device *adev,
+				    struct device *hostdev,
+				    const struct resource **res, int *num_res)
+{
+	struct acpi_device *host = to_acpi_device(adev->dev.parent);
+	struct resource_entry *rentry;
+	LIST_HEAD(resource_list);
+	struct resource *resources;
+	int count;
+	int i;
+
+	if (!adev->status.present) {
+		dev_dbg(&adev->dev, "device is not present\n");
+		return -EIO;
+	}
+
+	if (acpi_device_enumerated(adev)) {
+		dev_dbg(&adev->dev, "has been enumerated\n");
+		return -EIO;
+	}
+
+	/*
+	 * The following code segment to retrieve the resources is common to
+	 * acpi_create_platform_device(), so consider a common helper function
+	 * in future.
+	 */
+	count = acpi_dev_get_resources(adev, &resource_list, NULL, NULL);
+	if (count <= 0) {
+		dev_dbg(&adev->dev, "failed to get resources\n");
+		return count ? count : -EIO;
+	}
+
+	resources = devm_kcalloc(hostdev, count, sizeof(*resources),
+				 GFP_KERNEL);
+	if (!resources) {
+		dev_warn(hostdev, "could not allocate memory for %d resources\n",
+			 count);
+		acpi_dev_free_resource_list(&resource_list);
+		return -ENOMEM;
+	}
+	count = 0;
+	list_for_each_entry(rentry, &resource_list, node) {
+		resources[count] = *rentry->res;
+		hisi_lpc_acpi_fixup_child_resource(hostdev, &resources[count]);
+		count++;
+	}
+
+	acpi_dev_free_resource_list(&resource_list);
+
+	/* translate the I/O resources */
+	for (i = 0; i < count; i++) {
+		int ret;
+
+		if (!(resources[i].flags & IORESOURCE_IO))
+			continue;
+		ret = hisi_lpc_acpi_xlat_io_res(adev, host, &resources[i]);
+		if (ret) {
+			dev_err(&adev->dev, "translate IO range %pR failed (%d)\n",
+				&resources[i], ret);
+			return ret;
+		}
+	}
+	*res = resources;
+	*num_res = count;
+
+	return 0;
+}
+
+static int hisi_lpc_acpi_remove_subdev(struct device *dev, void *unused)
+{
+	platform_device_unregister(to_platform_device(dev));
+	return 0;
+}
+
+static int hisi_lpc_acpi_clear_enumerated(struct acpi_device *adev, void *not_used)
+{
+	acpi_device_clear_enumerated(adev);
+	return 0;
+}
+
+struct hisi_lpc_acpi_cell {
+	const char *hid;
+	const struct platform_device_info *pdevinfo;
+};
+
+static void hisi_lpc_acpi_remove(struct device *hostdev)
+{
+	device_for_each_child(hostdev, NULL, hisi_lpc_acpi_remove_subdev);
+	acpi_dev_for_each_child(ACPI_COMPANION(hostdev),
+				hisi_lpc_acpi_clear_enumerated, NULL);
+}
+
+static int hisi_lpc_acpi_add_child(struct acpi_device *child, void *data)
+{
+	const char *hid = acpi_device_hid(child);
+	struct device *hostdev = data;
+	const struct hisi_lpc_acpi_cell *cell;
+	struct platform_device *pdev;
+	const struct resource *res;
+	bool found = false;
+	int num_res;
+	int ret;
+
+	ret = hisi_lpc_acpi_set_io_res(child, hostdev, &res, &num_res);
+	if (ret) {
+		dev_warn(hostdev, "set resource fail (%d)\n", ret);
+		return ret;
+	}
+
+	cell = (struct hisi_lpc_acpi_cell []){
+		/* ipmi */
+		{
+			.hid = "IPI0001",
+			.pdevinfo = (struct platform_device_info []) {
+				{
+					.parent = hostdev,
+					.fwnode = acpi_fwnode_handle(child),
+					.name = "hisi-lpc-ipmi",
+					.id = PLATFORM_DEVID_AUTO,
+					.res = res,
+					.num_res = num_res,
+				},
+			},
+		},
+		/* 8250-compatible uart */
+		{
+			.hid = "HISI1031",
+			.pdevinfo = (struct platform_device_info []) {
+				{
+					.parent = hostdev,
+					.fwnode = acpi_fwnode_handle(child),
+					.name = "serial8250",
+					.id = PLATFORM_DEVID_AUTO,
+					.res = res,
+					.num_res = num_res,
+					.data = (struct plat_serial8250_port []) {
+						{
+							.iobase = res->start,
+							.uartclk = 1843200,
+							.iotype = UPIO_PORT,
+							.flags = UPF_BOOT_AUTOCONF,
+						},
+						{}
+					},
+					.size_data =  2 * sizeof(struct plat_serial8250_port),
+				},
+			},
+		},
+		{}
+	};
+
+	for (; cell && cell->hid; cell++) {
+		if (!strcmp(cell->hid, hid)) {
+			found = true;
+			break;
+		}
+	}
+
+	if (!found) {
+		dev_warn(hostdev,
+			 "could not find cell for child device (%s), discarding\n",
+			 hid);
+		return 0;
+	}
+
+	pdev = platform_device_register_full(cell->pdevinfo);
+	if (IS_ERR(pdev))
+		return PTR_ERR(pdev);
+
+	acpi_device_set_enumerated(child);
+	return 0;
+}
+
+/*
+ * hisi_lpc_acpi_probe - probe children for ACPI FW
+ * @hostdev: LPC host device pointer
+ *
+ * Returns 0 when successful, and a negative value for failure.
+ *
+ * Create a platform device per child, fixing up the resources
+ * from bus addresses to Logical PIO addresses.
+ *
+ */
+static int hisi_lpc_acpi_probe(struct device *hostdev)
+{
+	int ret;
+
+	/* Only consider the children of the host */
+	ret = acpi_dev_for_each_child(ACPI_COMPANION(hostdev),
+				      hisi_lpc_acpi_add_child, hostdev);
+	if (ret)
+		hisi_lpc_acpi_remove(hostdev);
+
+	return ret;
+}
+#else
+static int hisi_lpc_acpi_probe(struct device *dev)
+{
+	return -ENODEV;
+}
+
+static void hisi_lpc_acpi_remove(struct device *hostdev)
+{
+}
+#endif // CONFIG_ACPI
+
+/*
+ * hisi_lpc_probe - the probe callback function for hisi lpc host,
+ *		   will finish all the initialization.
+ * @pdev: the platform device corresponding to hisi lpc host
+ *
+ * Returns 0 on success, non-zero on fail.
+ */
+static int hisi_lpc_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct logic_pio_hwaddr *range;
+	struct hisi_lpc_dev *lpcdev;
+	resource_size_t io_end;
+	int ret;
+
+	lpcdev = devm_kzalloc(dev, sizeof(*lpcdev), GFP_KERNEL);
+	if (!lpcdev)
+		return -ENOMEM;
+
+	spin_lock_init(&lpcdev->cycle_lock);
+
+	lpcdev->membase = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(lpcdev->membase))
+		return PTR_ERR(lpcdev->membase);
+
+	range = devm_kzalloc(dev, sizeof(*range), GFP_KERNEL);
+	if (!range)
+		return -ENOMEM;
+
+	range->fwnode = dev_fwnode(dev);
+	range->flags = LOGIC_PIO_INDIRECT;
+	range->size = PIO_INDIRECT_SIZE;
+	range->hostdata = lpcdev;
+	range->ops = &hisi_lpc_ops;
+	lpcdev->io_host = range;
+
+	ret = logic_pio_register_range(range);
+	if (ret) {
+		dev_err(dev, "register IO range failed (%d)!\n", ret);
+		return ret;
+	}
+
+	/* register the LPC host PIO resources */
+	if (is_acpi_device_node(range->fwnode))
+		ret = hisi_lpc_acpi_probe(dev);
+	else
+		ret = of_platform_populate(dev->of_node, NULL, NULL, dev);
+	if (ret) {
+		logic_pio_unregister_range(range);
+		return ret;
+	}
+
+	dev_set_drvdata(dev, lpcdev);
+
+	io_end = lpcdev->io_host->io_start + lpcdev->io_host->size;
+	dev_info(dev, "registered range [%pa - %pa]\n",
+		 &lpcdev->io_host->io_start, &io_end);
+
+	return ret;
+}
+
+static int hisi_lpc_remove(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct hisi_lpc_dev *lpcdev = dev_get_drvdata(dev);
+	struct logic_pio_hwaddr *range = lpcdev->io_host;
+
+	if (is_acpi_device_node(range->fwnode))
+		hisi_lpc_acpi_remove(dev);
+	else
+		of_platform_depopulate(dev);
+
+	logic_pio_unregister_range(range);
+
+	return 0;
+}
+
+static const struct of_device_id hisi_lpc_of_match[] = {
+	{ .compatible = "hisilicon,hip06-lpc", },
+	{ .compatible = "hisilicon,hip07-lpc", },
+	{}
+};
+
+static const struct acpi_device_id hisi_lpc_acpi_match[] = {
+	{"HISI0191"},
+	{}
+};
+
+static struct platform_driver hisi_lpc_driver = {
+	.driver = {
+		.name           = DRV_NAME,
+		.of_match_table = hisi_lpc_of_match,
+		.acpi_match_table = hisi_lpc_acpi_match,
+	},
+	.probe = hisi_lpc_probe,
+	.remove = hisi_lpc_remove,
+};
+builtin_platform_driver(hisi_lpc_driver);